Lincoln Electric K2513-1 Manuel utilisateur

Marque: Lincoln Electric

Modèle: K2513-1

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

Operator’s Manual

WIRE FEEDER WELDERS (125, 140 MODELS)

www.lincolnelectric.com/register

Authorized Service and Distributor Locator:

www.lincolnelectric.com/locator

IM10049-A | Issue D ate Mar- 14

For use with machines having Code Numbers:

11631, 11632, 11633, 11634,

11635, 11636, 11637, 11638,

11639, 12100, 12101, 12102,

12103, 12104, 12105, 12106,

12107

Save for future reference

Date Purchased

Code: (ex: 10859)

Serial: (ex: U1060512345)

OPERATOR’S MANUAL

MANUAL DE OPERACIÓN

MANUEL DE L’OPÉRATEUR

THANK YOU FOR SELECTING

A QUALITY PRODUCT BY

LINCOLN ELEC TRIC.

!

"

When this equipment is shipped, title passes to the purchaser upon

receipt by the carrier. Consequently, Claims for material damaged in

shipment must be made by the purchaser against the transportation

company at the time the shipment is received.

""

Lincoln arc welding and cutting equipment is designed and built with

safety in mind. However, your overall safety can be increased by

proper installation ... and thoughtful operation on your part.

DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT

WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS

CONTAINED THROUGHOUT. And, most importantly, think before you

act and be careful.

This statement appears where the information must be followed

exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed to

avoid minor personal injury or damage to this equipment.

"

DON’T get too close to the arc. Use

corrective lenses if necessary to

stay a reasonable distance away

from the arc.

READ and obey the Material Safety

Data Sheet (MSDS) and the warning

label that appears on all containers

of welding materials.

USE ENOUGH VENTILATION or

exhaust at the arc, or both, to keep

the fumes and gases from your breathing zone and the general area.

IN A LARGE ROOM OR OUTDOORS, natural ventilation may be

adequate if you keep your head out of the fumes (See below).

USE NATURAL DRAFTS or fans to keep the fumes away from your

face.

If you de velop unusual symptoms, see your supervisor. Perhaps the

welding atmosphere and ventilation system should be checked.

""

PROTECT your eyes and face with welding helmet

properly fitted and with proper grade of filter plate

(See ANSI Z49.1).

PROTECT your body from welding spatter and arc

flash with protective clothing including woolen

clothing, flame-proof apron and gloves, leather

leggings, and high boots.

PROTECT others from splatter, flash, and glare with

protective screens or barriers.

IN SOME AREAS, protection from noise may be

appropriate.

BE SURE protective equipment is in good condition.

Also, wear safety glasses in work area

AT ALL

TIMES.

SPECIAL SITUATIONS

DO NOT WELD OR CUT containers or materials which previously had

been in contact with hazardous substances unless they are properly

cleaned. This is extremely dangerous.

DO NOT WELD OR CUT painted or plated parts unless special

precautions with ventilation have been taken. They can release highly

toxic fumes or gases.

Additional precautionary measures

PROTECT compressed gas cylinders from excessive heat, mechanical

shocks, and arcs; fasten cylinders so they cannot fall.

BE SURE cylinders are never grounded or part of an electrical circuit.

REMOVE all potential fire hazards from welding area.

ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR

IMMEDIATE USE AND KNOW HOW TO USE IT.

WARNING

CAUTION

SECTION A:

WARNINGS

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel Engines

Diesel engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects, and other

reproductive harm.

Gasoline Engines

The engine exhaust from this product contains chemicals known

to the State of California to cause cancer, birth defects, or other

reproductive harm.

 #

"

" "

  



Read and understand the following safety highlights. For additional

safety information, it is strongly recommended that you purchase a

copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the

American Welding Society, P.O. Box 351040, Miami, Florida 33135 or

CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety”

booklet E205 is available from the Lincoln Electric Company, 22801

St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION,

MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE POWERED

EQUIPMENT.

1.a. Turn the engine off before troubleshooting

and maintenance work unless the

maintenance work requires it to be running.

1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes outdoors.

1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from

vaporizing on contact with hot engine parts

and igniting. Do not spill fuel when filling

tank. If fuel is spilled, wipe it up and do not start engine until

fumes have been eliminated.

1.d. Keep all equipment safety guards, covers and

devices in position and in good repair.Keep

hands, hair, clothing and tools away from

V-belts, gears, fans and all other moving parts

when starting, operating or repairing

equipment.

1.e. In some cases it may be necessary to remove safety guards to

perform required maintenance. Remove guards only when

necessary and replace them when the maintenance requiring

their removal is complete. Always use the greatest care when

working near moving parts.

1.f. Do not put your hands near the engine fan. Do not attempt to

override the governor or idler by pushing on the throttle control

rods while the engine is running.

1.g. To prevent accidentally starting gasoline engines while turning

the engine or welding generator during maintenance work,

disconnect the spark plug wires, distributor cap or magneto wire

as appropriate.

1.h. To avoid scalding, do not remove the radiator

pressure cap when the engine is

hot.

ELECTRIC AND

MAGNETIC FIELDS MAY

BE DANGEROUS

2.a. Electric current flowing through any conductor

causes localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and welding

machines

2.b. EMF fields may interfere with some pacemakers, and welders

having a pacemaker should consult their physician before

welding.

2.c. Exposure to EMF fields in welding may have other health effects

which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work

cables. If the electrode cable is on your right side, the

work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as pos-

sible to the area being welded.

2.d.5. Do not work next to welding power source.

SAFETY

OPERATOR’S MANUAL

ELECTRIC SHOCK

CAN KILL.

3.a. The electrode and work (or ground) circuits are

electrically “hot” when the welder is on. Do

not touch these “hot” parts with your bare skin

or wet clothing. Wear dry, hole-free gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full area

of physical contact with work and ground.

0$'',6,10616+(014/$.5$)(6;24(&$76,105,)

9(.',0*/756%(2(4)14/('70'(4(.(&64,&$..;

+$<$4'175&10',6,105,0'$/2.1&$6,105149+,.(

9($4,0*9(6&.16+,0*10/(6$.5647&674(557&+$5

).1145*4$6,0*5145&$))1.'59+(0,0&4$/2('

215,6,10557&+$55,66,0*-0((.,0*14.;,0*,)6+(4(

,5$+,*+4,5-1)70$81,'$%.(14$&&,'(06$.&106$&6

9,6+6+(914-2,(&(14*4170'75(6+()1..19,0*

(37,2/(06

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic welding

gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection should

be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical (earth)

ground.

3.f. Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of electrode

holders connected to two welders because voltage

between the

two can be the total of the open circuit voltage of both

welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see It ems 6.c. and 8.

ARC RAYS CAN BURN.

4.a. Use a shield with the proper filter and cover plates to protect your

eyes from sparks and the rays of the arc when welding or

observing open arc welding. Headshield and filter lens should

conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant material

to protect your skin and that of your helpers from the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES

CAN BE DANGEROUS.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases. When welding, keep your head out of the fume.

Use enough ventilation and/or exhaust at the arc to keep fumes

and gases away from the breathing zone. +(09(.',0*

9,6+(.(&641'(59+,&+4(37,4(52(&,$.8(06,.$6,10

57&+$556$,0.(5514+$4')$&,0*5((,05647&6,105

10&106$,0(4141410.($'14&$'/,7/

2.$6('56((.$0'16+(4/(6$.514&1$6,0*59+,&+

241'7&(+,*+.;61:,&)7/(5-((2(:21574($5.19

$52155,%.($0'9,6+,0$22.,&$%.($0'

.,/,6575,0*.1&$.(:+$75614

/(&+$0,&$.8(06,.$6,100&10),0('52$&(514,0

51/(&,4&7/56$0&(5176'1145$4(52,4$614/$;

%(4(37,4(''',6,10$.24(&$76,105$4($.51

4(37,4('9+(09(.',0*10*$.8$0,<('56((.

5. b. The operation of welding fume control equipment is affected by

various factors including proper use and positioning of the

equipment, maintenance of the equipment and the specific

welding procedure and application involved. Worker exposure

level should be checked upon installation and periodically

thereafter to be certain it is within applicable OSHA PEL and

ACGIH TLV limits.

5.c. Do not weld in locations near chlorinated hydrocarbon vapors

coming from degreasing, cleaning or spraying operations. The

heat and rays of the arc can react with solvent vapors to form

phosgene, a highly toxic gas, and other irritating products.

5.d. Shielding gases used for arc welding can displace air and

cause

injury or death. Always use enough ventilation, especially in

confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your employer’s

safety practices. MSDS forms are available from your welding

distributor or from the manufacturer.

5.f. Also see item 1.b.

SAFETY

WELDING AND CUTTING

SPARKS CAN CAUSE

FIRE OR EXPLOSION.

6.a. Remove fire hazards from the welding area. If

this is not possible, cover them to prevent the

welding sparks from starting a fire. Remember that welding

sparks and hot materials from welding can easily go through

small cracks and openings to adjacent areas. Avoid welding near

hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special

precautions should be used to prevent hazardous situations.

Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)

and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is

touching the work or ground. Accidental contact can cause

overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures will

not cause flammable or toxic vapors from substances inside.

They can cause an explosion even though they have been

“cleaned”. For information, purchase “Recommended Safe

Practices for the Preparation for Welding and Cutting of

Containers and Piping That Have Held Hazardous Substances”,

AWS F4.1 from the American Welding Society (see address

above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free

protective garments such as leather gloves, heavy shirt, cuffless

trousers, high shoes and a cap over your hair. Wear ear plugs

when welding out of position or in confined places. Always wear

safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area

as practical. Work cables connected to the building framework or

other locations away from the welding area increase the

possibility of the welding current passing through lifting chains,

crane cables or other alternate circuits. This can create fire

hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “ Standard for Fire Prevention During

Welding, Cutting and Other Hot Work”, available from NFPA, 1

Batterymarch Park, PO box 9101, Quincy, Ma 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER MAY EXPLODE IF

DAMAGED.

7.a. Use only compressed gas cylinders containing

the correct shielding gas for the process used

and properly operating regulators designed for

the gas and pressure used. All hoses, fittings,

etc. should be suitable for the application and

maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to

an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected

to physical damage.

• A safe distance from arc welding or cutting operations

and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight

except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders,

associated equipment, and CGA publication P-l, “Precautions for

Safe Handling of Compressed Gases in

Cylinders,” available

from the Compressed Gas Association 1235 Jefferson Davis

Highway, Arlington, VA 22202.

FOR ELECTRICALLY

POWERED EQUIPMENT.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on the

equipment.

8.b. Install equipment in accordance with the U.S. National Electrical

Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturer’s recommendations.

()(461

+662999.,0&1.0(.(&64,&&1/5$)(6;

)14$'',6,10$.5$)(6;,0)14/$6,10

SAFETY

Welding Safety

Interactive Web Guide

for mobile devices

OPERATOR’S MANUAL

TABLE OF CONTENTS

General Decription. . . . . . . . . . . . . . . . . . . . . . Page 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . .Section A

Technical Specifications . . . . . . . . . . . . . . . . . . . . .A-1

Identify and Locate Components for 125 Amp Unit .A-2

Identify and Locate Components for 140 Amp Unit .A-3

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .Section B

Safety and Product Description . . . . . . . . . . . . . . . .B-1

Controls and Settings . . . . . . . . . . . . . . . . . . .B-2, B-3

Dual Track Drive Roll and Wire Guide Table . . . . . .B-4

Setting Up and Making a Flux-Cored Weld with a 125Amp

or 140Amp machines . . . . . . . . . . . . . . . . .B-4 thru B-6

Setting Up and Making a MIG Weld and Install Shielding

Gas for a 140Amp machine . . . . . . . . . .B-7 thru B-10

Setting Up and Making a Aluminum Weld . . . . . . .B-11

Accessories . . . . . . . . . . . . . . . . . . . . . . . . .Section C

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . .C-1

Utility Carts . . . . . . . . . . . . . . . . . . . . . . . . . . .C-2, C-3

Maintenance . . . . . . . . . . . . . . . . . . . . . . . .Section D

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . .D-1

Wire Feed Compartment, Fan Motor, Wire Reel

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-1

Gun And Cable Maintenance . . . . . . . . . . . . . . . . . .D-2

Overload Protection . . . . . . . . . . . . . . . . . . . . . . . .D-2

Component Replacement Procedures . . . . . . . . . . .D-2

Troubleshooting . . . . . . . . . . . . . . . . . . . . .Section E

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . .E-1

How to Use Troubleshooting Guide . . . . . . . . . . . . .E-1

Troubleshooting Guide . . . . . . . . . . . . . . .E-2 thru E-3

Wiring Diagram and Dimension Print . . . . . . . . . Section F

Parts Pages . . . . . . . . . . . . . . . . . . . .P-653, P-202-E

PRODUCT DESCRIPTION

PRODUCT DESCRIPTION (PRODUCT CAPABILITIES)

The portable 125Amp Wire Feeder Model is capable of flux-cored

welding on mild steel. The portable 140Amp Wire Feeder Model is

capable of MIG welding on steel, stainless steel, and aluminum, in

addition to flux-core welding on mild steel.

MIG welding stands for Metal Inert Gas welding and requires a

separate bottle of shielding gas to protect the weld. The Shielding

gas used is determined by the type of material you are welding on.

Shielding gases can be purchased separately from your local

welding gas distributor. MIG welding is ideal for welding on thin

and clean materials when an excellent cosmetic weld is required.

An example is automotive body panels.

FCAW-S stands for Self shielding Flux-cored Arc Welding and does

not require a shielding gas to protect the weld since the welding

wire has special additives known as flux to protect the weld from

impurities. Flux-cored welding is ideal for medium to thicker

material and for welding on painted or rusty steel. Flux-cored

welding is also ideal for outdoor applications where windy condi-

tions might blow the MIG shielding gas away from the weld. Flux-

cored welding produces a good looking weld but does not produce

an excellent weld appearance as MIG welding does.

Your 140Amp machine includes the necessary items to weld with

either the flux-cored welding or MIG welding process on steel. To

weld on stainless steel, an optional stainless steel welding wire

can be purchased separately. The 140Amp machine is spool gun

ready and the machine can weld aluminum using .035”(0.9mm)

diameter 4043 aluminum welding wire. Since aluminum welding

wire is soft, an optional spool gun is recommended for best

results. A welding Procedure Decal on the wire drive compartment

door provides suggested settings for welding.

COMMON WELDING ABBREVIATIONS

GMAW (MIG)

• Gas Metal Arc Welding

FCAW (Innershield or Outershield)

• Flux Core Arc Welding

WIRE FEEDER WELDERS (125, 140)

OPERATOR’S MANUAL

A-1

INSTALLATIONWIRE FEEDER WELDERS (125, 140)

TECHNICAL SPECIFICATIONS

125 Amp units (K2479-1, K2513-1, K2696-1, K2699-1, K2785-1)

140 Amp units (K2480-1, K2514-1, K2658-1, K2697-1)

If connected to a circuit protected by fuses use Time Delay Fuse marked “D”.

Requirements For Maximum Output

In order to utilize the maximum output capability of the machine, a branch circuit capable

of 25 amps at 120 volts, 60 Hertz is required.

INPUT – SINGLE PHASE ONLY

RATED OUTPUT

OUTPUT

Standard Voltage/Frequency

120 V / 60 Hz

Duty Cycle

20% Duty Cycle

Current

90 Amps

Voltage at Rated Amperes

Welding Current Range

30-125 Amps

Input Voltage / Frequence

120V 60Hz

Height

13.7 in.

347 mm

Width

10.15 in.

258 mm

Depth

17.9 in.

454 mm

Weight

49.5 lbs.

22.5 kg.

Fuse or Breaker Size

1,2

20 Amp

Input Amps

Power Cord

15 Amp, 125 V,

Three Prong Plug

(NEMA Type 5-15P)

Extension Cord

3 Conductor # 12 AWG

(4mm

) or Larger

up to 50 ft.(15.2m)

Maximum-Open Circuit Voltage

33 V

Wire Speed Range

50 - 500 in/min.

(1.3 - 12.7 m/min.)

Input Current

20 Amps @ rated output

RECOMMENDED INPUT CABLE AND FUSE SIZES

PHYSICAL DIMENSIONS

INPUT – SINGLE PHASE ONLY

RATED OUTPUT

OUTPUT

Standard Voltage/Frequency

120 V / 60 Hz

Duty Cycle

20% Duty Cycle

Current

90 Amps

Voltage at Rated Amperes

19.5

Welding Current Range

30-140 Amps

Input Voltage / Frequence

120V 60Hz

Height

13.7 in.

347 mm

Width

10.15 in.

258 mm

Depth

17.9 in.

454 mm

Weight

49.5 lbs.

22.5 kg.

Fuse or Breaker Size

1,2

20 Amp

Input Amps

Power Cord

15 Amp, 125 V,

Three Prong Plug

(NEMA Type 5-15P)

Extension Cord

3 Conductor # 12 AWG

(4mm

) or Larger

up to 50 ft.(15.2m)

Maximum-Open Circuit Voltage

33 V

Wire Speed Range

50 - 500 in/min.

(1.3 - 12.7 m/min.)

Input Current

20 Amps @ rated output

RECOMMENDED INPUT CABLE AND FUSE SIZES

PHYSICAL DIMENSIONS

A-2

INSTALLATIONWIRE FEEDER WELDERS (125, 140)

• .025” -.035”(0.6mm-0.8mm) Dual Groove Drive Roll

(Factory installed .035”(0.9mm) groove ready for flux-

cored process)

• Black Gun Nozzle (Installed on Welding Gun)

• 2”(51mm) Spindle Adapter (For 8”

(203mm) reel of wire)

• Instruction Manual

• How to Weld “DVD”

• Wire Feeder Welder

• Work Cable & Clamp

• Magnum 100L Welding Gun

• (3) .035”(0.9mm) Contact Tips (1 installed on the welding gun)

• Spool of .035”(0.9mm) diameter NR-211MP Innershield Flux-

cored Wire

IDENTIFY AND LOCATE COMPONENTS for 125 AMP UNIT

.035

.035 NR-211 MP

.025 GROOVE

.035 GROOVE

"INSTRUCTION

MANUAL"

DVD

2" SPINDLE ADAPTER (FOR 8" REEL OF WIRE)

OPERATOR’S MANUAL

A-3

INSTALLATIONWIRE FEEDER WELDERS (125, 140)

• Wire Feeder Welder

• Work Cable & Clamp

• Magnum 100L Welding Gun

• (3) .035”(0.9mm) Contact Tips (1 installed on the welding gun).

• (3) .025”(0.6mm) Contact Tips

• Spool of .035”(0.9mm) diameter NR-211MP

Innershield Flux-cored Wire

• Spool of .025”(0.6mm) diameter Super Arc L-56 MIG Wire

• .025” -.035”(0.6mm-0.8mm) Dual Groove Drive Roll

(Factory installed .035”(0.9mm) groove ready for

flux-cored process).

• Black Gun Nozzle (Installed on Welding Gun)

• Brass MIG Gun Nozzle for MIG welding

• 2”(51mm) Spindle Adapter for 8”(203mm) reel of

wire.

• Regulator

• Gas Hose

• Instruction Manual

• How to Weld “DVD”

.025

.035

NR-211 MP

WIRE

L-56 MIG

NR-211 MP

WIRE

L-56 MIG

IM10049

"INSTRUCTION

MANUAL"

DVD

GAS HOSE

REGULATOR

2" SPINDLE ADAPTER (FOR 8" REEL OF WIRE)

IDENTIFY AND LOCATE COMPONENTS for 140 AMP UNIT

.025 GROOVE

.035 GROOVE

B-1

OPERATION

WIRE FEEDER WELDERS (125, 140)

Read entire operation section before operating the

WIRE FEEDER WELDERS.

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts or

electrode with skin or wet clothing.

Insulate yourself from work and ground.

• Always wear dry insulating gloves.

FUMES AND GASES can be danger-

ous.

• Keep your head out of fumes.

• Use ventilation or exhaust to remove

fumes from breathing zone.

WELDING SPARKS can cause fire or

explosion.

• Keep flammable material away.

• Do not weld on closed containers.

ARC RAYS can burn eyes and skin.

• Wear eye, ear and body protection.

Observe all safety information throughout this

manual.

------------------------------------------------------

OPERATOR’S MANUAL

WARNING

B-2

OPERATION

WIRE FEEDER WELDERS (125, 140)

CONTROLS AND SETTINGS

This machine has the following controls:

See Figure B.1

1. POWER SWITCH – Turns power on and off to the machine.

2. ARC VOLTAGE CONTROL – This knob sets the output voltage

of the machine. Along with wire feed speed (WFS), this con-

trol sets a weld procedure. Refer to the procedure decal on

the wire drive compartment door to set a welding procedure

based on the type of material and thickness being welded.

3. WIRE FEED SPEED CONTROL (WFS) – This knob sets the

speed that the machine feeds wire. Along with arc voltage,

this control sets a weld procedure. Refer to the procedure

decal on the wire drive compartment door to set a welding

procedure based on the type of material and thickness being

welded.

See Figure B.2

4. GUN TRIGGER – Pressing the trigger activates the wire drive

and energizes the output of the machine. Press the trigger to

weld and release the trigger to stop welding.

5. WELDING GUN – Delivers wire and welding current to the

work piece.

a. Gun Liner – wire travels through the liner from the wire

drive. The gun liner will feed .025” to .035”(0.6mm to

0.9mm) wire.

b. Contact Tip – provides electrical contact to the wire.

c. Nozzle – When flux-cored welding, the black nozzle pro-

tects the mounting threads on the gun. When MIG welding,

the brass nozzle funnels the shielding gas to the weld.

6. WORK CLAMP & CABLE – Clamps to the work piece being

welded and completes the electrical welding circuit.

7. GUN TRIGGER CONNECTOR RECEPTACLE – Plug the 4 pin

gun trigger connector into this receptacle.

FIGURE B.1

FIGURE B.2

B-3

OPERATION

WIRE FEEDER WELDERS (125, 140)

See Figure B.3

8. WELDING GUN CONNECTOR BUSHING & THUMBSCREW –

Provides electrical power to the welding gun. The thumbscrew

holds the welding gun into the connector block. (Front Cover

and Side Door have been removed for clarity of Items 8 and

9).

9. OUTPUT TERMINALS - Connections to these terminals deter-

mines the welding polarity, depending on whether the process

being used is flux-cored welding or MIG welding.

See Figure B.4

10. WIRE SPOOL SPINDLE AND BRAKE – Holds a 4”(102mm)

diameter spool. Use the 2”(51mm) spindle adapter included

with the machine for 8” (203mm) diameter spools. The wing

nut sets the brake friction to prevent the spool from over

rotating when the trigger is released. Tightening the wing nut

will prevent the spool from rotating when the trigger is

released.

See Figure B.5

11. WIRE DRIVE & COMPONENTS – Feeds wire from the wire

spool through the drive and through the welding gun to the

work piece.

a. Drive Roll – Drives the wire through the drive system. The

drive roll has grooves to match the specific wire type and

diameter. Refer to Table B.1 for available drive rolls.

b. Incoming & Outgoing Guide – The wire is fed through

both guides. The Pivot Arm Assembly, Tension Arm

Assembly and Drive Roll keep pressure on the wire in the

groove.

c. Tension Arm Assembly – Turning clockwise increases the

forward force on the wire and turning counterclockwise

decreases the force.

FIGURE B.3

FIGURE B.4

FIGURE B.5

FIGURE B.5a

WIRE SPOOL

.035" (0.9mm)

NR-211-MP

DRIVE ROLL

PIVOT ARM ASSE MBLY

TENSION ARM ASSEMBL

OUTGOING GUIDE

INCOMING GUIDE

BEARING

See Figure B.5a

Magnum 100SG / Magnum 100L Switch - The spool gun

switch is available on 140 Amp machines only. The Magnum

100SG Spool Gun can be purchased at authorized retailers. The

part number is K2532-1.

MAGNUM 100SG

SWITCH

MAGNUM 100L

OPERATOR’S MANUAL

B-4

OPERATION

WIRE FEEDER WELDERS (125, 140)

A. ITEMS NEEDED FOR FLUX

CORED WELDING

1. .035”(0.9mm) Contact Tip

2. Dual Groove Drive Roll.

3. .035”(0.9mm) NR-211MP Flux-Cored

Wire

4. Black Flux Cored gun nozzle

5. Welding Gun

7. Work Cable & Clamp

.035

.035 NR-211 MP

SETTING UP AND MAKING A FLUX-CORED WELD WITH 125AMP OR 140AMP MACHINES

TABLE B.1

DRIVE ROLLS

See Figure B.6

12. CIRCUIT BREAKER – If the rated input current of the machine is

exceeded this circuit breaker will trip. Press to reset.

13. GAS INLET –Shielding gas connects to this inlet

(This is not available on 125 Amp Unit.)

FIGURE B.6

125/140 Amp

.025 GROOVE

.035 GROOVE*

Wire Diameter & Type

.025”(0.6mm) MIG wire

.030”(0.8mm) MIG wire

.035”(0.9mm) MIG wire

.030”(0.8mm) flux-cored

.035”(0.9mm) flux-cored

Smooth Drive Roll

(Dual Grooves)

Use .025”(0.6mm) Drive Roll Groove

Use .035”(0.9mm) Drive Roll Groove

Drive Roll Part

Number

KP2948-1

B-5

OPERATION

WIRE FEEDER WELDERS (125, 140)

B. CONNECT LEADS AND CABLES ON THE MACHINE

(See Figure B.7)

1. Open the case side door

2. Slide the connector end of the gun and cable through the

hole in the machine front and into the gun connector bush-

ing. Tighten thumb screw to connector bushing.

3. Make sure the gun connector end is seated fully into the

wire drive.

4. Plug the gun trigger lead connector into the 4 pin gun trigger

receptacle on the machine front.

5. Wire Drive Polarity. NR-211 MP requires negative (-) polarity.

Connect the short power cable from the wire drive to the

negative (-) output terminal and tighten wing nut.

6. Work Lead Connection. Slide the lugged end of the work

cable through the hole in the machine front and route cable

through strain relief as shown in figure B.7. Place lug on the

positive (+) output terminal and tighten wing nut.

C. LOAD WIRE SPOOL

(See Figure B.8)

1. Locate the sample spool of .035”(0.9mm) NR-211MP flux-

cored wire and place onto wire spool spindle. Orient the

spool so that the wire feeds off the top of the spool.

2. Secure spool by tightening the wing nut against the spacer

that holds the wire spool on the spindle. Do not over tighten

the spool.

3. Open the pivot arm assembly by rotating the tension arm

assembly down and lift pivot arm assembly up.

4. Remove drive roll

by un-screwing the black knob that holds the

drive roll on. Install the Dual Groove drive roll with the

.035”(0.9mm) mark facing outward which will allow feeding of

.035”

(0.9mm)

NR-211MP flux-cored wire

5. Carefully unwind and straighten the first six inches of welding

wire from the spool. Do not let the end of the wire go to prevent

the wire from unspooling.

WORK CLAMP

(4 PIN)

TRIGGER RECEPTACLE

PLUGGED IN

ALL COMPONENTS SHOWN CONNECTED

(FRONT AND SIDE DOOR IS REMOVED

FOR CLARITY)

SHORT POWER

CABLE NEGATIVE "-"

OUTPUT TERMINAL

WORK LEAD

STRAIN

RELIEF

CONNECTION

POSITIVE "+"

OUTPUT TERMINAL

TIGHTEN THUMB SCREW TO

CONNECTOR BUSHING

GUN AND CABLE

WORK CLAMP

(4 PIN)

LEAD CONNECTOR

TERMINAL END

(FITS ON STUD INSIDE

SEE FIGURE BELOW)

SLIDE

CONNECTOR

END HERE

OPEN LATCH DOOR

FIGURE B.7

WIRE SPOOL

.035" (0.9mm)

NR-211-MP

DRIVE ROLL

PI VOT AR M ASSE MBLY

TENSION ARM ASSEMBL

OUTGOING GUIDE

BEARING

INCOMING GUIDE

FIGURE B.8

OPERATOR’S MANUAL

B-6

OPERATION

WIRE FEEDER WELDERS (125, 140)

(See Figure B.9)

6. Feed the wire through the incoming guide, over the drive

roll groove, thru the outgoing guide and wire drive outlet on

the gun side.

7. Close the Pivot Arm Assembly and secure by rotating the

Tension Arm Assembly back to the up position. (See Tension

information on decal.)

(See Figure B.10)

8. Remove the nozzle from the gun and contact tip and

straighten the gun out flat.

9. Turn the machine power to on and depress the gun trigger

to feed the wire through the gun liner until the wire comes

out of the threaded end of the gun several inches. (See fig-

ure B.11)

10. When trigger is released spool of wire should not unwind.

Adjust wire spool brake accordingly.

MOVING PARTS AND ELECTRICAL CONTACT

CAN CAUSE INJURY OR BE FATAL.

•When the gun trigger is depressed, drive

rolls, spool of wire and electrode are ELEC-

TRICALLY LIVE (HOT).

• Keep away from moving parts and pinch points.

• Keep all doors, covers, panels and guards

securely in place.

DO NOT REMOVE OR CONCEAL WARNING

LABELS.

-------------------------------------------------------------------

11. Install the .035”

(0.9mm)

contact tip.

12. Install the black welding nozzle to the gun.

13. Trim the wire stickout to 3/8”

(9.5mm)

from the contact tip.

(See Figure B.12)

14. Close the case side door. The machine is now ready to

weld.

15. "Learn to Weld" Video is on the DVD.

16. Based on the thickness of the material you are going to

weld and the type and diameter of the welding wire, set the

voltage and the wire feed speed per the procedure decal

attached to the inside of the wire drive compartment door.

REMOVED NOZZLE

REMOVED CONT

ACT

TIP

LAY

CABLE AND GUN STRAIGHTEN

THIS POSITION

.035"(0.9mm)

NR-211-MP

WIRE SPOOL

PLUG IN POWER

INPUT CORD

DEPRESS

TRIGGER

ACTIVATE WIRE,

WHICH FEEDS

THE WIRE

THRU THE LINER.

FEED WIRE

APPROXIMA

TEL

Y 4.00"

FROM THE GUN

TUBE END

ON/OFF

SWITCH

WORK CLAMP AND CABLE

ROTATION

.035"(0.9mm)

NR-211-MP

WIRE SPOOL

WIRE SPOOL BRAKE

TENSION ARM ASSEMBL

LOCKED IN UP POSITION

PIVOT ARM ASSEM BLY

WITH BEARING PRESSING

AGAINST DRIVE ROLL

DIRECTION

OF WIRE

WIRE SPOOL

.035" (0.9mm)

NR-211-MP

DRIVE ROLL

INCOMING

GUIDE

OUTGOING GUIDE

BEARING

SLIDE WIRE

INTO GUN

CONNECTOR

SIDE

FIGURE B.10

FIGURE B.11

INSTALL .035 CONTACT TIP

INSTALL BLACK NOZZLE

TRIM WIRE

STICKOUT

3/8"(9.5mm)

from the Contact Tip

FIGURE B.9

FIGURE B.12

WARNING

B-7

OPERATION

WIRE FEEDER WELDERS (125, 140)

A. ITEMS NEEDED FOR MIG WELDING

1. .025”(0.6mm) Contact Tip

3. .025”(0.6mm) Dual Groove drive roll is used with L-56 Solid

Mig wire.

4. .025”(0.6mm) SuperArc L-56 Solid MIG Wire

5. Brass gun nozzle

6. Welding Gun

.025

WIRE

L-56 MIG

7. Work Cable & Clamp

8. Gas Regulator & Gas Line

9. Bottle of 75/25 Ar/

shielding gas (or 100%

shielding

gas) (note this requires a

regulator adapter which is sold

separately).

75/25

FEMALE END

MIXES

MALE END

100%

(REQUIRES ADAPTER

SOLD SEPARATELY)

SETTING UP AND MAKING A MIG WELD 140AMP MACHINE*

* 125 Amp Units can not be upgraded for MIG welding.

OPERATOR’S MANUAL

B-8

OPERATION

WIRE FEEDER WELDERS (125, 140)

B. INSTALL SHIELDING GAS

MIG welding requires an appropriate bottle of shielding gas. For

mild steel a cylinder of Ar/CO

or 100% CO

can be used; refer to

the following instructions to properly connect shielding gas to the

machine.

CYLINDER may explode if damaged. Keep

cylinder upright and chained to support

• Keep cylinder away from areas where it

may be damaged.

• Never lift welder with cylinder attached.

• Never allow welding electrode to touch

cylinder.

• Keep cylinder away from welding or

other live electrical circuits.

75/25

FEMALE END

MALE END

S19298

REGULATOR

ADAPTER

PLASTIC

WASH ER

MIXES

100%

3. Attach the flow regulator to the cylinder valve and tighten the

union nut securely with a wrench.

NOTE: If connecting to 100%

cylinder, a

regulator

adapter is required. Purchase separately S19298

adapter,

be sure to install plastic washer included in the fitting on the

bottle side.(See Figure B.13 )

4. Refer to Figure B.13. Attach one end of inlet gas hose to the

outlet fitting of the flow regulator and tighten the union nut

securely with a wrench. Connect the other end to the machine

Solenoid Inlet Fitting (5/8-18 female threads — for CGA — 032

fitting). Make certain the gas hose is not kinked or twisted.

FIGURE B.13

BUILDUP OF SHIELDING GAS may harm

health or kill.

• Shut off shielding gas supply when not

in use.

1. Secure the cylinder to a wall or other stationary support

to prevent the cylinder from falling over. Insulate the

cylinder from the work circuit and earth ground. Refer to

Figure B.13.

2. With the cylinder securely installed, remove the cylinder

cap. Stand to one side away from the outlet and open the

cylinder valve very slightly for an instant. This blows

away any dust or dirt which may have accumulated in

the valve outlet.

BE SURE TO KEEP YOUR FACE AWAY FROM THE VALVE OUT-

LET WHEN “CRACKING” THE VALVE. Never stand directly in

front of or behind the flow regulator when opening the cylin-

der valve. Always stand to one side.

SHIELDING GAS

1. For

, open the cylinder very slowly. For argon-mixed gas,

open cylinder valve slowly a fraction of a turn. When the cylin-

der pressure gauge pointer stops moving, open the valve fully.

2. Set gas flow rate for 30 to 40 cubic feet per hour (14 to 18

L/min) under normal conditions. Increase to as high as 40 to 50

CFH (18 to 23.5 L/min) for out of position welding.

3. Keep the cylinder valve closed, except when using the

machine.

WARNING

B-9

OPERATION

WIRE FEEDER WELDERS (125, 140)

C. CONNECT LEADS AND CABLES ON THE MACHINE

(See Figure B.14)

1. Open the case side door.

2. Slide the connector end of the gun and cable through the hole

of the machine front and into the gun connector bushing on

the wire drive. Tighten thumbscrew to connector bushing.

3. Make sure the gun connector end is seated fully into the wire

drive.

4. Plug the gun trigger lead connector into the 4 pin gun trigger

receptacle on the machine front.

5. Wire Drive Polarity. MIG welding requires Positive (+) polarity.

Connect the short power cable from the wire drive to the posi-

tive (+) output terminal and tighten wingnut.

6. Work Lead Connection. Slide the lugged end of the work

cable through the hole in the machine front and route cable

through the strain relief as shown in figure B.14. Place lug on

the negative (-) output terminal and tighten wing nut.

D. LOAD WIRE SPOOL

(See Figure B.15)

1. Locate the sample spool of .025”(0.6mm) L-56 solid MIG wire

and place onto wire spool spindle. Orient the spool so that the

wire feeds off the top of the spool.

2. Secure spool in place by tightening the wing nut against the

spacer that holds the wire spool on the spindle.

3. Open the pivot arm assembly by rotating the tension arm

assembly down and lift pivot arm assembly up.

4. Remove drive roll

by un-screwing the black knob that holds the

drive roll on. Install the Dual Track drive roll with the

.025”(0.6mm) mark facing outward which will allow feeding of

.025”

(0.6mm)

L-56 Solid MIG wire

5. Carefully unwind and straighten the first six inches of welding

wire from the spool. Hold onto the wire until the the Pivot Arm

assembly and Tension Arm are locked in place. This will pre-

vent the wire from unspooling.

GUN AND CABLE

WORK CLAMP

(4 PIN)

LEAD CONNECTOR

TERMINAL END

(FITS ON STUD INSIDE

SEE FIGURE BELOW)

SLIDE

CONNECTOR

END HERE

OPEN LATCH DOOR

LOCATE COMPONENTS

TO CONNECT TO THE

FRONT OF MACHINE

WORK CLAMP

(4 PIN)

TRIGGER RECEPTACLE

PLUGGED IN

ALL COMPONENTS SHOWN CONNECTED

(FRONT AND SIDE DOOR IS REMOVED

FOR CLARITY)

SHORT POWER

CABLE POSITIVE

"+"

OUT PUT TER MI NAL

WORK LEAD

CONNECTION

NEGATIVE "-"

OUT PUT TER MI NAL

GAS LINE

TIGHTEN THUMB SCREW TO

CONNECTOR BUSHING

STRAIN

RELIEF

FIGURE B.15

FIGURE B.14

WIRE SPOOL

.025" (0.6mm)

L-56 SOLID

MIG WIRE

DRIVE ROLL

PI VOT AR M ASSE MBLY

TENSION ARM ASSEMBL

OUTGOING GUIDE

BEARING

INCOMING GUIDE

OPERATOR’S MANUAL

B-10

OPERATION

WIRE FEEDER WELDERS (125, 140)

(See Figure B.16)

6. Feed the wire through the incoming guide, over the drive roll

groove, thru the outgoing guide and wire drive outlet on the

gun side.

7. Close the Pivot Arm Assembly and secure by rotating the

Tension Arm Assembly back to the up position. (See Tension

information on decal.)

(See Figure B.17)

8. Remove the nozzle from the gun and contact tip and

straighten the gun out flat.

9. Turn the machine power switch to on and press the gun trig-

ger to feed wire through the gun liner until the wire comes

out of the threaded end of the gun several inches. (See

Figure B.18)

10. When trigger is released, the spool of wire should not

unwind. Adjust wire spool brake accordingly.

MOVING PARTS AND ELECTRICAL CONTACT

CAN CAUSE INJURY OR BE FATAL.

•When the gun trigger is depressed drive rolls,

spool of wire and electrode are ELECTRICALLY

LIVE (HOT).

• Keep away from moving parts and pinch

points.

• Keep all doors, covers, panels and guards

securely in place.

DO NOT REMOVE OR CONCEAL WARNING

LABELS.

--------------------------------------------------------------------

11. Install the .025”(0.6mm) contact tip.

12. Install the brass MIG welding nozzle to the gun.

13. Trim the wire stickout to 3/8”(9.5mm) from the nozzle end.

(See Figure B.19)

14. Close the wire drive compartment door. The machine is now

ready to weld.

15. "Learn to Weld" Video is on the DVD.

16. Based on the thickness of the material you are going to weld

and the type and diameter of the welding wire, set the volt-

age and the wire feed speed per the procedure decal

attached to the inside of the wire drive compartment door.

TENSION ARM ASSEMBL

LOCKED IN UP POSITION

PIVOT ARM ASSEMBLY

WITH BEARING PRESSING

AGAINST DRIVE ROLL

DIRECTION

OF WIRE

WIRE SPOOL

.025" (0.6mm)

L-56 Solid

MIG WIRE

DRIVE ROLL

INCOMING

GUIDE

OUTGOING GUIDE

BEARING

SLIDE WIRE

INTO GUN

CONNECTOR

SIDE

WIRE SPOOL

.025" (0.6mm)

REMOVED NOZZLE

REMOVED CONTACT TIP

CABLE

AND GUN STRAIGHTEN

IN T HI S POS IT I O N

PLUG IN POWER

INPUT CORD

DEPRESS

TRIGGER

ACTIVA

TE WIRE,

WHICH FEEDS THE WIRE

THRU

THE LINER.

FEED WIRE

APPROXIMATELY

4.00"

FROM

THE GUN

TUBE END

ON/OFF

SWITCH

WORK CLAMP AND CABLE

ROTATION

WIRE SPOOL

WIRE SPOOL BRAKE

.025" (0.6mm)

INSTALL .025 (0.6mm) CONTACT TIP

INSTALL BRASS NOZZLE

TRIM WIRE

STICKOUT

3/8"(9.5mm)

from the Brass Nozzle

FIGURE B.17

FIGURE B.18

FIGURE B.19

FIGURE B.16

WARNING

La page charge ...

Lincoln Electric K2513-1 Manuel utilisateur

Marque: Lincoln Electric

Modèle: K2513-1

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Lincoln Electric K2513-1 User manual
español: Lincoln Electric K2513-1 Manual de usuario

Documents connexes

Autres documents

Tweco Tweco Spool Gun Manuel utilisateur