DeWalt DCS690X2W388B Manuel utilisateur

Marque: DeWalt

Modèle: DCS690X2W388B

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCS690

9" (230 mm) Cut Off Saw

Scie à Béton de 230mm (9po)

Sierra de corte de 230 mm (9")

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 17

Español (traducido de las instrucciones originales) 35

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

Rear handle

Trigger switch

Lock-off button

Battery door latch

Battery door

1/2" (13mm) wrench

and storgage

Heavy load indicator LED

Front handle

Guard

Guard rotation handle

Arbor screw

Blade rotation indicator

Spindle lock button

Guard rotation release

lever

Tool tag mounting holes

Water valve

Water inlet

Fig. A

8 9

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

ENGLISH

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

Additional Specific Safety Instructions for

Cut-Off Machines

a ) The guard provided with the tool must be

securely attached to the power tool and

positioned for maximum safety, so the least

amount of wheel is exposed towards the

operator. Position yourself and bystanders

away from the plane of the rotating wheel. The

guard helps to protect operator from broken wheel

fragments and accidental contact withwheel.

b ) Use only bonded reinforced wheels or diamond

blades for your power tool. Just because an

accessory can be attached to your power tool, it does

not assure safeoperation.

c ) The rated speed of the accessory must be at least

equal to the maximum speed marked on the

power tool. Accessories running faster than their

rated speed can break and flyapart.

d ) Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-off wheel. Abrasive cut-off wheels are

intended for peripheral grinding, side forces applied to

these wheels may cause them toshatter.

e ) Always use undamaged wheel flanges that are of

correct diameter for your selected wheel. Proper

wheel flanges support the wheel thus reducing the

possibility of wheelbreakage.

f ) Do not use worn down reinforced wheels from

larger power tools. Wheels intended for a larger

power tool are not suitable for the higher speed of a

smaller tool and mayburst.

g ) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot

be adequately guarded orcontrolled.

h ) The arbor size of wheels and flanges must

properly fit the spindle of the power tool. Wheels

and flanges with arbour holes that do not match the

mounting hardware of the power tool will run out

of balance, vibrate excessively and may cause loss

ofcontrol.

i ) Do not use damaged wheels. Before each use,

inspect the wheels for chips and cracks. If power

tool or wheel is dropped, inspect for damage or

install an undamaged wheel. After inspecting

and installing the wheel, position yourself and

bystanders away from the plane of the rotating

wheel and run the power tool at maximum no

load speed for one minute. Damaged wheels will

normally break apart during this testtime.

j ) Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and shop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable

of stopping flying debris generated by various

operations. The dust mask or respirator must be

capable of filtering particles generated by your

operation. Prolonged exposure to high intensity

noise may cause hearingloss.

k ) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments

of workpiece or of a broken wheel may fly away and

cause injury beyond immediate area ofoperation.

l ) Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact hidden

wiring. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electricshock.

m ) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning wheel may grab the surface and pull the

power tool out of yourcontrol.

n ) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into yourbody.

o ) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electricalhazards.

ENGLISH

p ) Do not operate the power tool near flammable

materials. Sparks could ignite thesematerials.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel. Pinching or snagging causes rapid stalling

of the rotating wheel which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the wheel’s

rotation at the point of thebinding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump

toward or away from the operator, depending on direction

of the wheel’s movement at the point of pinching. Abrasive

wheels may also break under theseconditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as givenbelow.

a ) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always hold front and rear

handle for maximum control over kickback or

torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper

precautions aretaken.

b ) Never place your hand near the rotating

accessory. Accessory may kickback over yourhand.

c ) Do not position your body in line with the

rotating wheel. Kickback will propel the tool in

direction opposite to the wheel’s movement at the

point ofsnagging.

d ) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have

a tendency to snag the rotating accessory and cause

loss of control orkickback.

e ) Do not attach a saw chain, woodcarving blade or

toothed saw blade on the saw. Such blades cause

frequent kickback and loss ofcontrol.

f ) Do not use a segmented wheel with a peripheral

gap greater than 3/8" (10mm).

g ) Do not "jam" the wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or binding of

the wheel in the cut and the possibility of kickback or

wheelbreakage.

h ) When wheel is binding or when interrupting a

cut for any reason, switch off the power tool and

hold the power tool motionless until the wheel

comes to a complete stop. Never attempt to

remove the wheel from the cut while the wheel

is in motion otherwise kickback may occur.

Investigate and take corrective action to eliminate the

cause of wheelbinding.

i ) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in

theworkpiece.

j ) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under

their own weight. Supports must be placed under

the workpiece near the line of cut and near the edge of

the workpiece on both sides of thewheel.

k ) Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can causekickback.

Additional Safety Information

• Use of accessories not specified in this manual is not

recommended and may be hazardous. Use of power

boosters that would cause the tool to be driven at speeds

greater than its rated speed constitutesmisuse.

• Do not use circular saw blades with this tool. Serious

injury mayresult.

• Avoid bouncing the wheel or giving it rough

treatment. If this occurs, stop the tool and inspect the

wheel for cracks orflaws.

• Direct sparks away from operator, bystanders or

flammable materials. Sparks may be produced while

using a cut-off tool. Sparks may cause burns or startfires.

• Always use front handle. Make sure the front handle

is securely tightened before use. The front handle

should always be used to maintain control of the tool at

alltimes.

• Never cut into area that may contain electrical

wiring or piping. Serious injury mayresult.

• Clean out your tool often, especially after heavy

use. Dust and grit containing metal particles often

accumulate on interior surfaces and could create an

electric shockhazard.

• Do not operate this tool for long periods of time.

Vibration caused by tool action may be harmful

to your hands and arms. Use gloves to provide extra

cushion and limit exposure by taking frequent restperiods.

• Never use the weight of the tool to stop

bladerotation.

• Never leave your cut-off machine unattended if it is

in operating mode. When your cut-off machine is not in

use, remove the battery pack, make sure the trigger switch

is in the OFF position and lock-off button isengaged.

• Always wear sturdy boots with non-slip soles and

heavy-duty work gloves when operating your cut-off

machine. Heavy-duty gloves improve your grip and

protect yourhands.

• Always use NIOSH/OSHA approved respiratory

protection when wet cutting below the

recommended flowrate.

• Consult and follow any federal, state or local laws or

regulations with respect to dry and wetcutting.

ENGLISH

• Never touch the rotating wheel with any part of

yourbody.

• When transporting the machine always make sure

the lock-off button is in the lockedposition.

• Remove the cutting wheel after use. The cutting wheel

may suffer damage duringtransport.

• Never use a cutting wheel that is damaged, is untrue

orvibrates.

• Never use your cut-off machine while standing on a

ladder orscaffolding.

• Never cut above your shoulderheight.

• Do not cut wood or any material from which the

cutting wheel is notrated.

• Use the wet cut method when using a diamond

blade whenever possible. The water can act as a

lubricant and reduce the risk reactiveforces.

• Use caution when reentering a cut. Do not push the

cutting wheel into the cut at an angle as this can increase

the risk onbinding.

• Always be alert of anything that could cause the

workpiece to close at the cut and pinch the cutting

wheel. Always support the workpiece in a manner that

results in the cut remaining open. Never make a cut that

could result in binding of the cuttingwheel.



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols.

The symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

ENGLISH

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a shortcircuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use

andShipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to the

FLEXVOLT™ battery, the

battery is in Shipping Mode.

Strings of cells are electrically

disconnected within the pack resulting in three batteries

with a lower Watt hour (Wh) rating as compared to one

battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hourbatteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 batteryimplied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

ENGLISH

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

ENGLISH

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center forrecycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting batterypack.

Fig. C

2. Insert the battery pack

18

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

19

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before

firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132:

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

yellow light will turn off and the charger will resume the

chargingprocedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing to light or by displaying a problem pack or charger

blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fullycharged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

ENGLISH

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaningsolutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack in an air temperature below +40°F

(+4.5°C), or above +104°F (+40°C). This is important

and will prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting toclean.

6. Do not freeze or immerse the charger in water or any

otherliquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat orcold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged beforeuse.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

Intended Use

This cut off tool is designed for professional

cuttingapplications.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

This cut off tool is a professional power tool. DO NOT let

children come into contact with the tool. Supervision is

required when inexperienced operators use thistool.

SPECIFICATIONS

DCS690

Blade diameter 9" (230 mm)

Arbor size 7/8" (22.2 mm)

RPM 6600

Lock-Off Button (Fig. A)

Your cut-off tool is equipped with a lock-off button

To lock the trigger switch in the OFF postition, push the

lock-off button from the left side of the tool. To unlock the

trigger switch, push the lock-off button from the right side

of thetool.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. Make sure

the trigger switch is in the OFFposition. An accidental

start-up can causeinjury.

Spindle Lock Button (Fig. A)

The spindle lock button

13

is used to lock the arbor

screw

11

when changingaccessories.

1. To engage the spindle lock button, remove the battery

pack and make sure trigger switch is in the OFF position

and lock-off button isengaged.

2. Depress the spindle lock button and turn the wheel and

spindle until the lock button engages thespindle.

3. Use supplied wrench

to unscrew the arbor screw

11

and remove or mount accessories. Spindle threads are

righthand.

ENGLISH

Installing Abrasive and Diamond Wheels

(Fig. A, D)



WARNING: Install only oneblade.

1. Lay unit on a firm surface, with the arbor screw

facingupward.

2. Using supplied 1/2" (13mm) open end wrench

6

(located in the battery compartment), remove arbor

screw

11

, outer clamp washer

20

and used wheel

21

if one is installed. Hold arbor screw

from turning

with spindle lock button

. Spindle threads are

righthand.

3. The inner clamp washer

22

is held in place with a

double D shaft and retainingring.

4. Slip wheel over spindle

. Slip on outer clamp washer.

Start threading on arbor screw which will self align outer

clampwasher.

IMPORTANT: Make sure the diamond blade is installed

with the correct rotation, as marked on the blade

rotation indicator

12

5. Engage spindle lock button and tighten screw firmly

with wrench. Do not over-tighten arborscrew.

6. Turn wheel by hand to ensure it is properly centered.

The wheel should not hit the shoe or guard. The screw

and flanges should betight.



CAUTION: Only use 9" (230mm) Type 1/41 wheels

with 7/8" (22.2mm) arbor hole with this tool. Never

force a wheel onto the machine or alter the size of the

arborhole.

Fig. D

Replacing Worn Clamp Washers (Fig. D)



WARNING: Replace clamp washers as they wear.

They may become sharp with extendeduse.

1. Remove the arbor screw

11

, outer clamp washer

20

and used wheel

21

if one is installed as described in

Installing Abrasive and DiamondWheels.

2. To remove the inner clamp washer

, first remove the

retainingring that holds the inner clamp washer to the

double Dshaft.

3. Remove the inner clamp washer and replace with a new

one. Orient the inner clamp washer with the depressed

center section toward the blade. Make sure the new

inner clamp washer is secure with the retaining ring

inplace.

4. Install the wheel

, new outer clamp washer

, and

arbor screw

as described in Installing Abrasive and

DiamondWheels.

Adjusting the Guard Angle (Fig. E)



WARNING: Do not use guard rotation handle to

hold tool while cutting. Guard rotation handle is

only used for adjustment of the guard while tool is

not inuse.



CAUTION: Guard may be hot. Use guard handle to

rotateguard.



WARNING: Always make sure the guard is properly

engaged before starting themachine.

You can adjust the angle of theguard.

1. To adjust the angle of the guard, pull back the guard

rotation release lever

and holdit.

2. Grasp the guard

firmly by guard rotation handle

10

and rotate to desiredangle.

3. Release the guard rotation release lever and make sure

it engages, locking the guard in place. If the guard

rotation release lever doesn't engage, rotate the guard

slightly until the guard rotation release lever returns to

the lockedposition.

Fig. E

DeWALT

Tool Tag Ready (Fig. F)

Optional Accessory

Your cut-off saw comes with mounting holes

and

fasteners for installing a

DeWALT

Tool Tag. You will need

a T15 bit tip to install the tag. The

DeWALT

Tool Tag is

designed for tracking and locating professional power

tools, equipment, and machines using the

DeWALT

Tool

Connect™ app. For proper installation of the

DeWALT

Tool

Tag refer to the

DeWALT

Tool Tagmanual.

ENGLISH

Fig. F

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. Make sure

the trigger switch is in the OFFposition. An accidental

start-up can causeinjury.

Installing and Removing the Battery Pack

(Fig. G)

NOTE: For best results, make sure your battery pack is

fullycharged. Use only

DeWALT

FLEXVOLT™ batteries with

this cut-offmachine.

Unlock battery door

by moving battery door latch

towards the rear of the tool and open as shown in Figure G.

To install the battery pack

18

into the tool, align the

battery pack with the rails inside the tool and slide it in

until the battery pack is firmly seated. Ensure that it does

notdisengage.

Close the battery door

, and push the battery door

latch

4

forward towards the front of the tool to lock the

batterydoor.

To remove the battery pack from the tool, unlatch and open

the battery door. Then press the battery release button

19

and firmly pull the battery pack out of the tool. Insert it into

the charger as described in Charging aBattery.

Do not leave the battery dooropen.

Fig. G

Proper Hand Position (Fig. H)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.



WARNING: Never use the cut-off machine with one

hand. Always grip the cut-off machine firmly with

bothhands.



WARNING: Make sure the handles and grips of

your cut-off machine are secure and free of grease

and/ormoisture.

Proper hand position for both left- and right-handed users

requires your right hand on the rear handle

and your left

hand on the front handle

8

Fig. H

Heavy Load Indicator LED (Fig. A)

The heavy load indicator LED

will illuminate as a warning

when the tool is being pushed too hard. Continuing to

use the tool after the LED is lit could cause the tool to shut

down or reduce runtime.

Reducing the Risk of Kickback (Fig. I)



WARNING: Reactive forces may occur at any time

the cutting wheel is inmotion.



WARNING: To reduce the risk of kickback, avoid

cutting with the upper quadrant of the cutting

wheel whenever possible. Be extremely mindful

of binding or pinching of the cutting wheel in this

area as it can cause severe reactive forces resulting

inkickback.

• Always be alert to any potential movement that could

cause the material being cut to close and pinch the

cuttingwheel.

• Proper support of the material will ensure the cut stays

open during the cut. If you cannot properly support the

material, do not use a cut-off machine to make yourcut.

Fig. I

• Always support exposed pipe in the ground so that it

is stable and is able to support weight. Use additional

ENGLISH

support closer to the area to be cut to prevent the pipe

from sagging and pinching the cuttingwheel.

• Material that is under stress could shift when it is cut.

Uneven pipe beds could exertstress.

• Always make sure the section of material being

removed is also supported. After the first cut is made

you may have to move supports or add additional

support to ensure both sides of the material are

evenlysupported.

• Be aware of weakened work areas that could shift or

slide causing your supports tomove.

Making Cuts with a Cut-Off Machine



CAUTION: Before attempting to start, grasp tool

firmly with both hands beforelifting.



WARNING: Cut-off saw not intended for surface

grinding or other applications where side loading of

the blade isencountered.



WARNING: Edge cutting can be performed only

with wheels that are designed and specified for this

purpose. Protect yourself during edge cutting by

directing the open side of the guard away from you,

theoperator.



WARNING: Wheels used for cutting may break or kick

back if they bend or twist while the tool is being used

to do cut-offwork.



WARNING: Always be alert for gyroscopic forces that

can be generated by a rapidly spinning cutting wheel.

Moving the cut-off machine sideways can create a

gyroscopic force, causing the operator to experience

an unexpected perpendicular change indirection.

Wet Cut Method (Fig. A, J, K)



CAUTION: Close battery door and securely latch it

closed before using anywater.



CAUTION: Never use the saw over head. When using

water, limit cutting to the horizontal position to

reduce the risk of water entering thetool.



WARNING: Wet cut method is to be used only with

a diamondblade.



WARNING: The recommended flow rate should be at

least 20 fl. oz. (0.6 liters) per minute. Cutting at a flow

rate less than recommended or cutting for more than

two consecutive hours requires use of NIOSH/OSHA

approved respiratory protection for the operator and

anybystanders.



WARNING: Maximum supplied water pressure not to

exceed 60PSI (4.1bar).



WARNING: Makes sure that water does not flow onto

the abrasive wheel while the cut-off machine is not

in use. The cutting wheel will absorb water which will

affect thebalance.

NOTICE: Before using the wet cut method, make

sure water will not damage the material being cut or

surroundingproperty.

Attaching the Water Supply

1. Attach the water supply to the quick water

connector

23

2. Attach the quick water connector to the water inlet

17

Fig. J

3. To regulate the water flow, slowly rotate the water

valve

towards to open position until desired flow is

reached as shown in Figure K. To stop the flow of water,

rotate the water valve to the closedpostion.

4. Proceed to cut as described in Making a Cutbelow.

5. After finishing your cuts, run the machine for

3–5seconds with the water valve closed to remove any

residual water from the cuttingwheel.

OPEN CLOSED

Fig. K

Removing the Water Supply

1. Turn off and depressurize watersystem.

2. Make sure the trigger switch

is in the OFF position

and lock-off button

isengaged.

3. Close the water valve

16

4. Disconnect the quick water connector

from the

water inlet

17

Making a Cut



WARNING: Always make sure the guard is in place

and set for the type of cut you are making.



WARNING: Always use your cut-off machine so that

the operator and bystanders are not endangered by

potential airborne particles of material being cut,

sparks, or pieces of damaged cuttingwheels.



DANGER: To reduce the risk of serious or fatal injury,

DO NOT change direction during the cut. A change

in direction may produce a high torsional load on the

cutting wheel and cause it to bind or break.



CAUTION: Wear gloves when cuttingmetal.

ENGLISH

1. Mark a cutting line on the material to becut.

2. Grasp rear handle

1

and front handle

8

firmly.

3. Line up wheel with cutting line. Be sure nothing is near

or in line with thewheel.

4. Depress and hold trigger switch

, wait for the blade

to reach full speed, then slowly feed wheel into work

with firm pressure, working along the cutting line. Do

not force the tool. Cut only as deep as needed to reduce

the amount of dust produced. For maximum efficiency

and wheel life, keep the wheel speedhigh. To maintain

control of the cut-off machine, release pressure as you

near the end of yourcut.

5. To stop tool, release trigger switch

2

6. Set the lock-off button

to the locked postion and

make sure the cutting wheel has come to a complete

stop before setting the cut-off machinedown.

NOTE: Denser and thicker material should be cut in several

passes. The maximum depth of cut of each pass should not

exceed 1.0" (25.4mm).

Cutting Slabs (Fig. L, M)



WARNING: Before making any cuts, make sure the

slab is properly secured on a non-slipsurface.

1. Cut a guiding groove along a marked cuttingline.

2. Cut deeper into the slab, never exceeding the maximum

depth of cut of 3.25" (83mm), and leaving a ridge of

uncut material

as shown on Fig.L.

Fig. L

3. Cut through the slab at each end to ensure the slab

does notchip.

4. Break theslab.

NOTE: Curves must be made into the slab using several

straight cuts as shown in Fig. M, always making sure that the

cutting wheel does not becomewedged.

Fig. M

Cutting Pipe (Fig. N, O)



WARNING: Before making any cuts, make sure the

pipe is properly secured on a non-slipsurface.



WARNING: Pipe may break at any time during the

cut. Take precautions to maintain control of the tool

and avoid fallingdebris.

If the outer diameter of the pipe is smaller than the

maximum cutting depth

• Make one cut straight down, starting at the top of the

pipe through to the bottom of thepipe.

If the outer diameter of the pipe is larger than the

maximum cutting depth

Several cuts are needed on larger pipes and it is important

to make the cuts in the propersequence.

If the pipe is in-ground and can not be rolled, make

the following sequence of cuts

1. Cut a guiding groove along a marked cutting line

making sure to avoid any metal reinforcements

ifpossible.

2. Start at the bottom of the pipe and use only the front

and upper part of the cutting wheel. This will reduce the

risk of kickback orpinching.

3. Using only the front and upper part of the cutting

wheel, make a cut on the oppsite lower side of thepipe.

4. Make a lateral cut on the top half of thepipe.

5. Make a second lateral cut on the opposite side of the

top half.

IMPORTANT: To keep the pipe from pinching the

cutting wheel, make sure not to cut into the area of the

finalcut.

6. Make sure all the top and bottom cuts are complete

when making the final topcut.

IMPORTANT: Always make the final cut from the top

of the pipe. If the pipe is properly supported, this will

reduce the risk of pinching the cutting wheel. If any

pinching does occur it will be at the bottom of the

cutting wheel resulting in pull-away but notkickback.

Fig. N

If the pipe is free and can be rolled, make the

following sequence ofcuts

1. Secure the pipe on a non-slipsurface.

2. Using only the bottom part of the cutting wheel, make a

cut in the upper part of thepipe.

3. Roll the pipe and repeat steps 1 and 2 until the cut

iscomplete.

ENGLISH

Fig. O

Cutting a Recess in Concrete Pipe (Fig. P)



WARNING: Before making any cuts, make sure the

pipe is properly secured on a non-slipsurface.

Several cuts are needed to make a recess cut in

concrete pipe and it is important to make the cuts in the

propersequence.

1. First make two cuts along the length of the pipe.

Always make an axial cut to avoid pinching of the

cuttingwheel.

2. Insert wedges into thecuts.

3. Make the third and fourth cuts to complete therecess.

4. If the severed part remains after all four cuts are made,

do not make any more cuts. Break the severed partout.

Fig. P

Applications



WARNING: NEVER cut magnesium with this

tool. Magnesium particles may ignite causing

personalinjury.

• 1/8" (3mm) max. gauge sheet metal

• Concrete, cinder blocks and bricks

• Roofing tiles (terracotta or similar)

• Curb stone/pavers

• Asphalt

• Reinforcing rod; generally under 1" (25.4mm) diameter

• 1/8" (3mm) diameter concrete wire mesh

• Corrugated floor and ceiling form (concrete forms)

• Electrical conduit 1/8" (3mm) wall thickness

• 1/8" (3mm) max. thick structural forms such as channel,

angles, plate,etc.

NOTE: The cutting of materials heavier than those listed

above are not recommended due to the possibility of

tooldamage.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. Make sure

the trigger switch is in the OFFposition. An accidental

start-up can causeinjury.

Maintenance Schedule

Before use Daily/After work

Clean machine X

Check/clean handles X

Check intake port X

Check battery X

Check battery compartment X

Check water intake X

Check cutting wheel X

Check guide plate X

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.



WARNING: Do not use pressurized water to

clean your machine. This may damage parts of

themachine.

Accessories



WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.



WARNING: Accessories must be rated for at least

the speed recom mended on the tool warning label.

Wheels and other accessories running over rated

speed can fly apart and cause injury. Accessory

ratings must always be above tool speed as shown on

toolnameplate.

ENGLISH



WARNING: Handle and store all abrasive wheels

carefully to prevent damage from thermal shock, heat,

mechanical damage, etc. Store in a dry protected area

free from high humidity, freezing temperatures or

extreme temperaturechanges.

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

DeWALT

Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-

DeWALT

(1-800-433-9258) or visit our website:

www.dewalt.com.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a

DeWALT

factory

service center or a

DeWALT

authorized service center.

Always use identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from

the date of purchase. This warranty does not cover part

failure due to normal wear or tool abuse. For further detail

of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-

DeWALT

(1-800-

433-9258). This warranty does not apply to accessories

or damage caused where repairs have been made

or attempted by others. THIS LIMITED WARRANTY IS

GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB205BT, DCB206,

DCB606, DCB609

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

ENGLISH

TROUBLESHOOTING

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

For assistance with your product, visit our website at www.dewalt.com for a list of service centers, or call

DeWALT

1-800-4-

DeWALT

(1-800-433-9258).

PROBLEM POSSIBLE CAUSE SOLUTION

Machine will not start. Battery pack not installed properly. Check battery pack installation.

Battery pack not charged. Check battery pack charging requirements.

Battery pack too hot/cold. Allow battery to cool down or warm up.

Internal components too hot. Allow machine to cool down.

Machine shuts off abruptly. Battery pack has reached its maximum

thermal limit.

Allow battery pack to cool down.

Out of charge. (To maximize the life of the

battery pack it is designed to shut off

abruptly when the charge is depleted.)

Place on charger and allow to charge.

Reduced run time. Battery is not completely charged. Charge battery.

Life of the battery has been reached. Replace with a new D

WALT FLEXVOLT™ battery.

Battery pack will not charge. Battery pack not inserted into charger. Insert battery pack into charger until LED illuminates.

Charger not plugged in. Plug charger into a working outlet. Refer to Important

Charging Notes for more details.

Surrounding air temperature too hot or too cold. Move charger and battery pack to a surrounding air

temperature of approximately 65 °F – 75 °F (18 °C– 24 °C).

Frayed edges or tears on the

cutting wheel.

Cutting wheel wobbling. Replace with a new cutting wheel.

Cutting wheel is blunt. Replace with a new cutting wheel.

Built-up edges on the cutting wheel. Dress the cutting wheel by briefly cutting in abrasive material.

Cutting wheel wanders off the

cutting line.

Cutting wheel wobbling. Replace with a new cutting wheel.

Cutting wheel is blunt. Replace with a new cutting wheel.

Cutting wheel is not properly installed. Mount cutting wheel correctly. Refer to Installing Abrasive

and Diamond Wheels.

Wear on the side of the cutting wheel. Surface grinding. Do not surface grind with the cutting wheel.

Reduced or no cutting performance. Cutting wheel is blunt. Replace with a new cutting wheel.

Built-up edges on the cutting wheel for stone. Dress the cutting wheel for stone by briefly cutting in abrasive

material. Use a new cutting wheel for cutting asphalt.

Cutting wheel is not properly installed. Mount cutting wheel correctly. Refer to Installing Abrasive

and Diamond Wheels.

Cutting material for which the cutting wheel

is not rated.

Use the proper cutting wheel.

Chipping or cracking in the

wheel core.

Overload. Replace with a new cutting wheel.

Sparking. Built-up edges on the cutting wheel for stone. Dress the cutting wheel for stone by briefly cutting in abrasive

material. Use a new cutting wheel for cutting asphalt.

Heavy load indicator LED illuminated. Too much force on the tool. Reduce force.

FRANÇAIS

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels oumatériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à lasécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommagesmatériels.



AVERTISSEMENT! lire tous les

avertissements de sécurité et toutes

les directives. Le non-respect des

avertissements et des directives pourrait

se solder par un choc électrique, un

incendie et/ou une blessuregrave.

AVERTISSEMENT : afin de réduire

le risque de blessures, lire le mode

d’emploi del’outil.

Pour toute question ou remarque au

sujet de cet outil ou de tout autre outil

DeWALT

, composez le numéro sans frais :

1-800-4-

DeWALT

(1-800-433-9258).

Poignée arrière

Gâchette

Bouton de verrouillage

Loquet du couvercle du

compartiment à piles

Couvercle du compartiment à piles

Clé de 13mm (1/2po) et

rangement

Témoin à DEL de charge

importante

Poignée avant

Protecteur

Poignée de pivotement du

protecteur

Vis de l’arbre

Indicateur de rotation de lame

Bouton de verrouillage du fuseau

Levier de dégagement du

pivotement du protecteur

Trous de montage de la balise de

l’outil

Robinet d’eau

Orifice d’admission d’eau

Français (traduction de la notice d’instructions originale)

Fig. A

FRANÇAIS

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

POUR LES OUTILS ÉLECTRIQUES



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sansfil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique.

Une distraction pourrait en faire perdre la maîtrise

àl’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc électrique est plus élevé si votre corps

est mis à laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive.

Ne jamais utiliser le cordon pour transporter,

tirer ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à

l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue

pour l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique

est utilisé. Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence de drogues,

d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut

entraîner des blessures corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source

d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter

un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de

provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les

situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

4) Utilisation et entretien d’un outil

électrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

La page est en cours de chargement...

DeWalt DCS690X2W388B Manuel utilisateur

Marque: DeWalt

Modèle: DCS690X2W388B

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCS690X2W388B User manual
español: DeWalt DCS690X2W388B Manual de usuario

DeWalt DCS690X2W388B Manuel utilisateur

Ce manuel convient également à

DeWalt DCS690X2W388B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents