Kohler K-2604-1WA Guide d'installation

Marque: Kohler

Modèle: K-2604-1WA

Taper: Guide d'installation

Installation and Care

Guide

Vanity

K-2604, K-5288, K-5289

M product numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

M corresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1267640-2-A

Tools and Materials

Before You Begin

CAUTION: Risk of property damage. Select 250 lb (113.4

kg) load bearing 5/16″ lag bolts with a length to clear

obstacles in the wall and 5/16″ washers. Calculate proper lag

bolt length by adding the following: 1-1/2″ (38 mm) backing

material + wallboard thickness + back rail thickness.

IMPORTANT! Risk of product damage. Do not modify the vanity.

Doing so will compromise structural stability.

IMPORTANT! Risk of product damage. Use care when moving the

vanity to avoid impacting, sliding, or side-loading the legs.

NOTICE: Siliconized acrylic caulk must be used to secure the sink

to the vanity. Do not use 100% silicone sealant which will damage

the ﬁnish of the vanity.

NOTICE: The ﬁnished wall must be straight and plumb to ensure

proper support of the vanity and alignment of the sink and door.

Plus:

• Wood Screws

• 2x6s

• 5/16" Lag Bolts and Washers

[Min 250 lb (113.4 kg) Load Bearing]

• Socket Wrenches

• Siliconized Acrylic Caulk

1267640-2-A 2 Kohler Co.

1. Prepare the Site

NOTICE: If the K-2607 bridge cabinet will also be installed, extend

the backing material a minimum of 12″ (305 mm) beyond the width

of the vanity on the side where the bridge will be installed.

NOTICE: To properly secure the vanity, the top of the required 2x6

backing material must be 32-1/2″ (826 mm) from the ﬁnished ﬂoor.

Measure and mark 32-1/2″ (826 mm) up from the ﬁnished ﬂoor.

This will be the height from the ﬁnished ﬂoor to the top of the

2x6 backing material.

Ensure there are no obstructions in the wall (such as wiring or

plumbing) from the marked height down to the ﬂoor. If there are

obstructions, select another area to install the vanity.

NOTICE: Extend the backing material beyond the width of the

vanity to the nearest stud to ensure proper support for the vanity.

Front-notch the studs 1-1/2″ (38 mm) to ensure the 2x6 backing

material is ﬂush against the studs.

Secure the 2x6 backing material to the studs with framing nails.

Rough-in the water supply and drain lines into the rough-in

plumbing area of the vanity.

NOTICE: The ﬁnished wall must be straight and plumb to ensure

proper support of the vanity and alignment of the sink and door.

2x6

Backing

Material

32-1/2" (826 mm)

Kohler Co. 3 1267640-2-A

Prepare the Site (cont.)

Complete the ﬁnished wall. Make sure the ﬁnished wall is

straight and plumb, and the ﬂoor is ﬂat and perpendicular to the

ﬁnished wall.

1267640-2-A 4 Kohler Co.

2. Secure the Vanity

CAUTION: Risk of property damage. Select 250 lb (113.4

kg) load bearing 5/16″ lag bolts with a length to clear

obstacles in the wall and 5/16″ washers. Calculate proper lag

bolt length by adding the following: 1-1/2″ (38 mm) backing

material + wallboard thickness + back rail thickness.

IMPORTANT! Risk of product damage. Use care when moving the

vanity to avoid impacting, sliding, or side-loading the legs.

With assistance, lift and place the vanity in position against the

ﬁnished wall. Do not drag the vanity into position.

Verify the vanity is level and the back rail is plumb against the

wall. If necessary, turn the leveler(s) to adjust the unit.

Using a 1/4″ drill bit, drill pilot holes through the back rail and

the ﬁnished wall. Verify the pilot holes are positioned to ensure

the lag bolts will engage the 2x6 backing material.

Secure the vanity to the wall with two 5/16″ lag bolts and

washers (not provided).

Install the Bridge Cabinet (Optional)

Refer to the installation instructions packed with the K-2607

bridge cabinet.

Pilot

Hole

Finished

Wall

Washer

Lag Bolt

Back Rail

Leveler

Kohler Co. 5 1267640-2-A

3. Install the Bathroom Sink

CAUTION: Risk of personal injury. Vitreous china sinks are

very heavy. Get help lifting and aligning the sink.

Install the faucet (if applicable) and drain to the sink. Refer to the

faucet and drain manufacturer’s installation instructions.

NOTICE: Siliconized acrylic caulk must be used to secure the sink

to the vanity. Do not use 100% silicone sealant which will damage

the vanity ﬁnish.

Run a 1/4″ (6 mm) continuous bead of siliconized acrylic caulk

around the top of the vanity, as illustrated.

NOTE: The sink is properly positioned when: (1) the back edge of

the sink is ﬂush against the ﬁnished wall and (2) the overhang on

the left, right, and front side of the sink is equal on each side of the

vanity.

With assistance, lift and properly position the sink on top of the

vanity.

Immediately wipe away any excess caulk that contacts the vanity.

Run a 1/8″ (3 mm) bead of siliconized acrylic caulk along the top

edge of the sink where it contacts the ﬁnished wall.

Finished

Wall

1267640-2-A 6 Kohler Co.

4. Reverse Door Swing

(Optional - 24″ only)

NOTE: To ease installation, get assistance supporting the door.

NOTE: The vanity comes with hinges installed on the inside left. To

reverse the door swing, use the included template (1181754-7) to

mount the brackets to the opposite side of the vanity.

Align the hinge hooks with the cup of the top bracket.

Slide the hinge onto the top bracket.

Clip the hinge onto the bracket to secure.

Repeat for the lower hinge.

Hook

Bracket

Cup

Kohler Co. 7 1267640-2-A

5. Adjust the Drawers

Remove

Slide the drawer out until fully extended.

From underneath, pull the release latches toward the center of the

drawer.

Lift the front of the drawer and pull toward you to disengage

from the rails.

Once removed, lay the drawer on a ﬂat, protective surface.

Reinstall

Fully extend the rails.

Align the holes in the back of the drawer with the rail hooks.

Rotate the drawer down onto the rails, engaging the front drawer

holes with the rail pins.

From underneath, push the release latches into the rails to secure

the drawer.

Latch

Rail

Hook

Holes

1267640-2-A 8 Kohler Co.

6. Recommended Hardware Placement

Measure and mark the dimensions for the hardware as shown

above.

Drill a 3/16″ (21 mm) pilot hole at each marking.

Drill a ﬁnished hole to size.

Insert a screw through each hole. Thread the knob onto the screw.

24” Vanity Installation

From the back side of the door, insert the screw through the

predrilled hole.

Thread the knob onto the screw. Tighten securely.

Repeat for the drawer.

K-5288: 6-1/16" (154 mm)

K-5289: 4-9/16" (116 mm)

4-3/4"

(121 mm)

(25 mm)

Kohler Co. 9 1267640-2-A

Adjust the Door

Adjust

Refer to the illustration and note the screwdriver location for the

desired adjustment.

Remove

Apply a small amount of leverage to the door with one hand to

keep the door in the full open position.

With the other hand, press the clip to release the lower hinge

latch from the bracket.

Repeat for the upper hinge.

Move the door forward to slide the hinges off the brackets.

Reinstall

Apply a small amount of leverage to the door with one hand to

keep the door in the full open position.

With the other hand, align the top hinge with the top bracket.

Clip the hinge onto the bracket to secure.

Repeat for the lower hinge.

Open and close the door to ensure proper operation.

Care and Cleaning

Vitreous China and Fireclay

•

Use a mild detergent such as liquid dishwashing soap and warm

water for cleaning. Do not use abrasive cleaners that may scratch

or dull the surface.

Adjustments

Side

Depth

Height

Bracket

Clip

1267640-2-A 10 Kohler Co.

Care and Cleaning (cont.)

•

Carefully read the cleaner product label to ensure the cleaner is

safe for use on the material.

•

Always test your cleaning solution on an inconspicuous area

before applying to the entire surface.

•

Do not allow cleaners to sit or soak on the surface.

•

Wipe surfaces clean and rinse completely with water immediately

after cleaner application. Rinse and dry any overspray that lands

on nearby surfaces.

•

Use a soft, dampened sponge or cloth. Never use an abrasive

material such as a brush or scouring pad to clean surfaces.

Wood Surfaces

•

As with any smooth surface, avoid using abrasive cleaners as

they will scratch the surface. Wipe the wood surface regularly to

prevent buildup of soap and scum.

•

To protect against scratches, use felt, leather, or cork under all

items placed on the wood surface. To conceal scratches, a

touch-up marker is available for order. Contact a Kohler

distributor or call 1-800-4-KOHLER for ordering information.

•

Do not expose wood furniture to direct sunlight, drying heat

sources, or dampness.

•

Dust frequently with a soft cloth in the direction of the grain. Use

only products speciﬁcally made for cleaning wood. Avoid using

oily polishes or waxes, or products containing silicone. Blot spills

immediately with a soft, damp cloth.

•

Every six months, remove soil buildup by rubbing with a soft

cloth dampened in a 50/50 solution of warm water and an

ammonia-free detergent. Wipe clean with a cloth dampened in

warm water, then wipe dry.

For detailed cleaning information and products to consider, visit

www.kohler.com/clean. To order Care & Cleaning information, call

1-800-456-4537.

Kohler Co. 11 1267640-2-A

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in

material and workmanship for one year from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate

adjustment where Kohler Co. inspection discloses any such defects

occurring in normal usage within one (1) year after installation. Kohler

Co. is not responsible for removal or installation costs. Use of in-tank

toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your

Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing

Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler,

WI 53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from

within the USA and Canada, and 001-800-456-4537 from within Mexico,

or visit www.kohler.com within the USA, www.ca.kohler.com from

within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE

DURATION OF THIS WARRANTY. KOHLER CO. AND/OR

SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states/provinces do not

allow limitations on how long an implied warranty lasts, or the

exclusion or limitation of special, incidental or consequential damages,

so these limitations and exclusions may not apply to you. This

warranty gives you speciﬁc legal rights. You may also have other

rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

1267640-2-A 12 Kohler Co.

Guide d’installation et d’entretien

Meuble de toilette

Outils et matériel

Avant de commencer

ATTENTION: Risque de dommages matériels. Choisir des

tire-fonds de 5/16″ porteurs de 250 lb (113,4 kg) avec une

longueur adéquate pour dégager les obstacles dans le mur,

ainsi que des rondelles de 5/16″. Calculer une longueur de

tire-fonds adéquate en ajoutant les valeurs suivantes:

matériau de renfort de 1-1/2″ (38 mm) + épaisseur de

panneau mural + épaisseur de rail arrière.

IMPORTANT! Risque d’endommagement du produit. Ne pas

modiﬁer le meuble de toilette. Ceci pourrait compromettre la

stabilité structurelle.

IMPORTANT! Risque d’endommagement du produit. Procéder

avec précaution lors du déplacement du meuble aﬁn d’éviter d’avoir

un impact sur les pieds, ou de faire glisser ou de charger ceux-ci sur

le côté.

AVIS: Du mastic à l’acrylique siliconisé doit être utilisé pour

sécuriser le lavabo sur le meuble. Ne pas utiliser de mastic à la

silicone à 100%, car cela endommagera la ﬁnition du meuble.

AVIS: La ﬁnition murale doit être droite et d’aplomb aﬁn d’assurer

un support adéquat du meuble et un alignement correct du lavabo

Plus:

• Vis à bois

• Lambourde de 2x6

• Tire-fonds de 5/16" et rondelles

[capacité de charge min 250 lb (113,4 kg)]

• Clés à douilles

• Mastic à l'acrylique siliconée

Kohler Co. Français-1 1267640-2-A

Avant de commencer (cont.)

et de la porte.

1267640-2-A Français-2 Kohler Co.

1. Préparer le site

AVIS: Si l’armoire pont K-2607 est également installée, prolonger le

matériau de renfort de 12″ (305 mm) minimum au-delà de la largeur

du meuble sur le côté où le pont sera installé.

AVIS: Pour bien ﬁxer le meuble, le dessus du matériau de renfort

2x6 requis doit se trouver à 32-1/2″ (826 mm) du plancher ﬁni.

Mesurer et marquer 32-1/2″ (826 mm) vers le haut à partir du

plancher ﬁni. Ceci sera la hauteur entre le plancher ﬁni et le

dessus du matériau de renfort 2x6.

S’assurer qu’il n’y ait pas d’obstructions dans le mur (comme un

câblage ou la plomberie) à partir de la hauteur marquée vers le

plancher. Si il y a des obstructions, choisir une autre zone dans

laquelle installer le meuble.

AVIS: Étendre le matériau de renfort au-delà de la largeur du

meuble jusqu’au montant le plus proche aﬁn d’assurer un support

adéquat du meuble.

Encocher les montants à l’avant de 1-1/2″ (38 mm) aﬁn d’assurer

que le matériau de renfort 2x6 soit à ras des montants.

Sécuriser le matériau de renfort 2x6 aux montants avec des clous

de cadrage.

Raccorder l’alimentation d’eau et les conduites d’écoulement dans

la zone de plomberie de raccordement du meuble.

Matériau de

renfort 2x6

32-1/2" (826 mm)

Kohler Co. Français-3 1267640-2-A

Préparer le site (cont.)

AVIS: La ﬁnition murale doit être droite et d’aplomb aﬁn d’assurer

un support adéquat du meuble et un alignement correct du lavabo

et de la porte.

Terminer la ﬁnition murale. S’assurer que la ﬁnition murale est

droite et d’aplomb, et que le sol est plat et perpendiculaire à la

ﬁnition murale.

1267640-2-A Français-4 Kohler Co.

2. Sécuriser le meuble

ATTENTION: Risque de dommages matériels. Choisir des

tire-fonds de 5/16″ porteurs de 250 lb (113,4 kg) avec une

longueur adéquate pour dégager les obstacles dans le mur,

ainsi que des rondelles de 5/16″. Calculer une longueur de

tire-fonds adéquate en ajoutant les valeurs suivantes:

matériau de renfort de 1-1/2″ (38 mm) + épaisseur de

panneau mural + épaisseur de rail arrière.

IMPORTANT! Risque d’endommagement du produit. Procéder

avec précaution lors du déplacement du meuble aﬁn d’éviter d’avoir

un impact sur les pieds, ou de faire glisser ou de charger ceux-ci sur

le côté.

Avec de l’assistance, lever et placer le meuble dans l’emplacement

prévu contre la ﬁnition murale. Ne pas faire glisser le meuble en

position.

Vériﬁer que le meuble est à niveau et que le rail arrière est

d’aplomb contre le mur. Si nécessaire, tourner le(s) vérin(s) de

calage pour ajuster l’ensemble.

Utiliser un foret de 1/4″ pour percer des trous pilotes à travers le

rail arrière et la ﬁnition murale. Vériﬁer que les trous pilotes sont

bien en place pour assurer que les tire-fonds seront engagés dans

le matériau de renfort 2x6.

Sécuriser le meuble sur le mur à l’aide de deux tire-fonds de

5/16″ et des rondelles (non fournis).

Orifice

pilote

Finition

murale

Rondelle

Tire-fond

Rail arrière

Vérin de calage

Kohler Co. Français-5 1267640-2-A

Sécuriser le meuble (cont.)

Installer l’armoire pont (optionnel)

Se référer aux instructions d’installation accompagnant l’armoire

pont K-2607.

1267640-2-A Français-6 Kohler Co.

3. Installer le lavabo

ATTENTION: Risque de blessures. Les lavabos en

porcelaine vitriﬁée sont très lourds. Demander de l’aide pour

soulever et aligner le lavabo.

Installer le robinet (si applicable) et le drain sur le lavabo. Se

référer aux instructions d’installation du fabricant du robinet et

du drain.

AVIS: Du mastic à l’acrylique siliconisé doit être utilisé pour

sécuriser le lavabo sur le meuble. Ne pas utiliser de mastic

d’étanchéité à la silicone à 100%, car cela endommagera la ﬁnition

du meuble.

Faire passer un boudin continu de mastic à l’acrylique siliconé de

1/4″ (6 mm) autour du dessus du meuble, comme sur

l’illustration.

REMARQUE: Le lavabo est positionné correctement lorsque: (1) le

rebord arrière du lavabo est à ras contre la ﬁnition murale et (2) le

dépassement à gauche, à droite et à l’avant du lavabo est égal sur

chaque côté du meuble.

Avec de l’assistance, soulever et positionner correctement le

lavabo au-dessus du meuble.

Essuyer immédiatement tout excès de mastic en contact avec le

meuble.

Finition

murale

Kohler Co. Français-7 1267640-2-A

Installer le lavabo (cont.)

Poser un boudin continu de mastic à l’acrylique siliconé de 1/8″

(3 mm) le long du rebord supérieur du lavabo au point de contact

de celui-ci avec la ﬁnition murale.

1267640-2-A Français-8 Kohler Co.

La page charge ...

Kohler K-2604-1WA Guide d'installation

Marque: Kohler

Modèle: K-2604-1WA

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Kohler K-2604-1WA Installation guide
español: Kohler K-2604-1WA Guía de instalación
português: Kohler K-2604-1WA Guia de instalação

Kohler K-2604-1WA Guide d'installation

Kohler K-2604-1WA Guide d'installation

dans d''autres langues

Documents connexes

Autres documents