Big Ass Fans Haiku Guide d'installation

Marque: Big Ass Fans

Modèle: Haiku

Taper: Guide d'installation

INSTALLATION GUIDE

READ AND SAVE THESE INSTRUCTIONS

Follow the instructions for your mount type. Each mount uses di erent parts and hardware.

Low Proﬁ le Mount

Mounting

Flat ceilings from 8 to 10.5 feet (2.4to 3.2 meters)

Input Voltage

100–240 VAC, 50–60 Hz

Universal Mount

Mounting

Sloped or ﬂ at ceilings from 10.5 to 14+feet (3.2 to 4.3+ meters)

Input Voltage

100–240 VAC, 50–60 Hz

Page 16Page 6

HAIKU® BY BIG ASS FANS

☑ Gather Tools

☑ Select Extension Tube (Universal Mount Only)

If your fan uses the universal mount, you will need to select

the appropriate extension tube for your ceiling height and

slope.

See page 4 for a guide to select the most appropriate

extension tube.

BEFORE YOU START

☑ Turn O Power

Contact a licensed electrician

if you are uncomfortable

performing electrical work. A

licensed electrician must install

the fan if required by local code.

Do not use the fan with a

dimmer switch.

Turn o power at breaker!

☑ Prepare Fan Site

Outlet Box: Make sure your outlet box is suitable for fan

support. If there is not an outlet box at the fan location,

install one on a ceiling joist or beam.

Concrete Ceiling: Install an anchor hook for the safety

cable if required by your local building and safety code.

See the following page for installation details.

Wood Ceiling Joist: Attach the mounting plate or mounting

bracket directly to the joist using two wood screws (not

supplied). Big Ass Fans recommends using corrosion-

resistant 12-11 x 45 mm hex head timber screws with seal.

Ø 6 mm

112 mm

45 mm 43 mm

40 mm

Ø 8 mm

(anchor bolt)

Ø 14 mm

(anchor hook)

80 mm

100 mm

Concrete Ceiling

Install an anchor hook for the safety cable if required by your local building and safety code.

Universal Mount Low Proﬁle Mount

50 mm max

40 mm max

50 mm max

40 mm max

HAIKU® BY BIG ASS FANS

Universal Mount

Drill three Ø 6 mm holes in the pattern shown. The hole depth should not exceed 40 mm. Remove any dust

from the holes. Insert three anchor bolts into the holes. Strike the heads of the anchor bolts with a hammer,

ensuring the bolt sleeves are ﬂ ush with the ceiling surface. Position the mounting bracket on the anchor

bolts. Ensure all three anchor bolts are fully tightened to expand and lock the anchors.

If required by local building and safety codes, install an anchor hook for the safety cable. Drill a Ø 8 mm

hole for the anchor hook. The hole depth should not exceed 50 mm. Remove any dust from the hole, and

then insert the anchor hook and fully tighten.

Low Proﬁ le Mount

Drill four Ø 8 mm holes in the pattern shown. The hole depth should not exceed 40 mm. Remove any dust

from the holes. Insert four anchor bolts into the holes. Strike the heads of the anchor bolts with a hammer,

ensuring the bolt sleeves are ﬂ ush with the ceiling surface. Position the mounting plate on the anchor bolts.

Ensure all four anchor bolts are fully tightened to expand and lock the anchors.

If required by local building and safety codes, install an anchor hook for the safety cable. Drill a Ø 14 mm

hole for the anchor hook in the pattern shown. The hole depth should not exceed 50 mm. Remove any dust

from the hole, and then insert the anchor hook and fully tighten.

Choosing an Extension Tube (Universal Mount Only)

Consult the tables below to select the appropriate extension tube for your fan.

Ceiling Slope

Haiku fans with a universal mount can be installed on sloped

ceilings with an angle no greater than 33°.

Fan Diameter

Maximum

Ceiling Slope

Extension Tube

Length

52 in.

(1.3 m)

26°

20 in.

(508 mm)

52 in.

(1.3 m)

33°

32 in.

(813 mm)

60 in.

(1.5 m)

22°

20 in.

(508 mm)

60 in.

(1.5 m)

33°

32 in.

(813 mm)

84 in.

(2.1 m)

16°

20 in.

(508 mm)

84 in.

(2.1 m)

29°

32 in.

(813 mm)

Ceiling Height

For optimum performance, Big Ass Fans recommends the

following extension tube lengths based on ceiling height.

Ceiling Height Extension Tube Length

10.5–11 ft

(3.2–3.4 m)

20 in.

(508 mm)

11–13 ft

(3.4–4 m)

32 in.

(813 mm)

13–14 ft *

(4–4.3 m) *

48 in. *

(1219 mm) *

>14 ft *

(>4.3 m) *

60 in. *

(1524 mm) *

* Big Ass Fans recommends using an extended length

extension tube for ceiling heights over 13 ft (4 m). The fan

comes standard with 20 in. (508 mm) and 32 in. (813 mm)

extension tubes. Other lengths are available by contacting

Customer Service.

HAIKU® BY BIG ASS FANS

Haiku Remote

Do not expose the remote control to rain or water.

Turns fan on or o.

Sets fan timer length of up to eight hours. Each

press extends timer by one hour.

Turns light on or o. Clears active fan timer.

Increases fan speed/light brightness. Varies fan speed to simulate a natural breeze.

Decreases fan speed/light brightness.

Automatically adjusts your fan speed overnight to

keep you comfortable while you sleep.

Universal Mount

UNIVERSAL MOUNT

Mounting Bracket

Canopy

Extension Tube

Lower Cover

M5 Screws (6)

Canopy Screws (4)

Wiring Cover

Airfoils (3)

M6 Nut

M6 x 32 mm Bolt

Fan Stabilizer Kit

(Flat ceilings only)

Grommets (6)

Mounting Ball

and Wedge

Motor Hub

Wire Connectors

6 mm Steel Pin

Safety cable not shown

If the EMI ﬁlter is included, install it with your fan.

Universal Mount

HAIKU® BY BIG ASS FANS

Install Airfoils

Moving clockwise, align each airfoil on the fan hub and secure

it with the airfoil hardware (Fig. 1). Make sure the sticker color

on each airfoil matches the corresponding sticker color on

the fan hub!

M5 Screw

Grommet

Fig. 1

Airfoil

Install Lower Cover

Attach the lower cover as shown (Fig. 2).

Lower Cover

Fig. 2

Universal Mount

Attach Extension Tube and Wiring Harness

Align the holes on the extension tube with the holes on the motor bracket, and then secure the tube with the M6 x 32 mm bolt and M6

nut (Fig. 3.1).

Connect the wiring harness from the extension tube to the receptacle from the motor hub (Fig. 3.2).

Fig. 3.1 Fig. 3.2

Wiring

Harness

M6 x 32 mm Bolt

M6 Nut

Universal Mount

HAIKU® BY BIG ASS FANS

Install Lower Safety Cable and Ground Wire

Install the safety cable and ground wire lugs with the unpainted screws and lock washers (Fig. 4.1).

Make sure all hardware is secure, and then gently tug the cables at the top of the extension tube to reduce slack (Fig.4.2).

Slide the wiring cover down the extension tube, resting it on the fan hub. Make sure no wires are visible between the cover and fan hub.

Slide the canopy down the extension tube (Fig.4.3).

Fig. 4.1 Fig. 4.2 Fig. 4.3

Wiring

Cover

Canopy

Safety Cable

Ground Wire

(Green)

Lock Lock

WasherWasher

Screw

Universal Mount

Install Mounting Ball

Slide the mounting ball over the extension tube (Fig. 5.1).

Insert the 6 mm steel pin into the hole at the top of the extension tube, and then slide the mounting ball upward, seating the steel pin in

the inner slots (Fig. 5.2).

Insert the wedge into the mounting ball and secure it with the screw. Tighten the screw enough to prevent movement between the

mounting ball and extension tube, but do not over-tighten (Fig. 5.3).

Fig. 5.1

Fig. 5.2

Fig. 5.3

Extension Extension

TubeTube

Mounting

Ball

6 mm Steel Pin

Screw

Wedge

Fig. 7

Mounting

Bracket

Mounting

Ball

Universal Mount

HAIKU® BY BIG ASS FANS

Hang Fan

Raise the fan to the mounting bracket. Align the rib in the

mounting bracket with the slot in the mounting ball, position the

mounting ball, and let the fan hang freely (Fig. 7).

Gently twist the extension tube to ensure it is properly seated

and will not move during fan operation.

Install Mounting Bracket

Disconnect power to the fan location before installing

the mounting bracket!

Secure the mounting bracket to the mounting structure with

suitable hardware (Fig. 6).

Outlet box shown. Your mounting structure may di er from

the illustration.

Fig. 6

Suitable Mounting

Hardware

Mounting

Bracket

Universal Mount

Wire the Fan

Disconnect power to the fan location before wiring the fan!

Do not connect the fan to a damaged power source! Do not attempt to resolve electrical failures on your own. Consult a

qualiﬁed electrician if uncertain of the electrical installation of this fan.

Wire the fan as shown in the diagram using the wire connectors (Fig. 8). If your fan packaging included an EMI ﬁlter, install it as shown.

Attach the green ground wire to the mount with the unpainted screw. Connect the wiring harness from the power supply to the wiring

harness from the extension tube, making sure that the wiring and safety cable are routed in the same direction.

North America

100–120 V

All other regions

AC Hot/L1

Brown

Black Brown

AC Neutral/L2

Blue

White Blue

PE/Earth Ground

Green with Yellow

Green or Bare

Copper

Green with Yellow

Fig. 8

Universal Mount

HAIKU® BY BIG ASS FANS

Wiring Diagram

(No EMI Filter)

WHITE

BLACK

BROWN

BLUE

WHITE

BLACK

BROWN

BLUE

EMI FILTER

Wiring Diagram

(With EMI Filter)

GREEN &

YELLOW

GREEN &

YELLOW

Universal Mount

Install Flat Ceiling Fan Stabilizer

Fit the stabilizer block into the notches on top of the mounting ball (Fig. 9.1).

Secure the stabilizer plate to the stabilizer block with the M6 x 70 mm bolt and M6 nut (Fig. 9.2).

Fig. 9.1 Fig. 9.2

Stabilizer Block

Mounting Ball

Stabilizer Plate

M6 x 70 mm Bolt

M6 Nut

Universal Mount

HAIKU® BY BIG ASS FANS

Raise Canopy

Raise the canopy to the mounting bracket, aligning the four

holes on the canopy with the holes on the bracket. Secure

the canopy to the mounting bracket with the painted screws

(Fig.11). Make sure all wires and the safety cable are tucked in

the canopy.

Secure Safety Cable

Loop the safety cable around the mounting bracket or building

structure, and then secure it with the shackle (Fig. 10).

Canada: The safety cable must be secured directly

to an existing part of the building structure. It

may be necessary to install additional structural

material to provide attachment points.

Safety Cable

Shackle

Canopy

Screw

Fig. 10

Fig. 11

Congratulations!

Installation is now complete. Test your fan using the remote

control.

Low Proﬁle Mount

LOW PROFILE MOUNT

Use the extension tube screw caps that match the color of your fan.

Safety cable not shown.

Mounting Plate

Rubber Bumpers (2)

Mounting Brackets (2)

6 mm Nylock Nuts (4)

Extension Tube Screw Caps (2)

Lower Cover

Grommets (6)

M5 Screws (6)

Motor Hub

Wiring Cover Screws (2)

Airfoils (3)

Wire Connectors

Wiring Cover

Wiring Cover Trim

Low Proﬁ le Mount

HAIKU® BY BIG ASS FANS

Install Mounting Plate and Single Bracket

Slide the rubber bumpers onto the extension tube brackets (Fig. 1.1).

Secure the mounting bracket to the mounting structure with suitable hardware (Fig. 1.2). Your mounting structure may di er from the

illustration.

Loosely attach one mounting bracket to the mounting plate with two 6 mm nylock nuts, but do not fully tighten (Fig. 1.3).

Fig. 1.1 Fig. 1.2 Fig. 1.3

Rubber

Bumper

Extension Tube Brackets

Mounting

Plate

6 mm Nylock Nut

Mounting Plate

Suitable Mounting

Hardware

Outlet box shown. Your mounting

structure may di er from the illustration.

Low Proﬁle Mount

Secure Safety Cable

Raise the fan to the bracket and temporarily rest one rubber bumper in the space between the bracket and plate (Fig. 2.1). While

supporting the fan, loop the safety cable around the mounting plate or building structure, and then secure it with the shackle (Fig.2.2).

Canada: The safety cable must be secured directly to an existing part of the building structure. It may be necessary to

install additional structural material to provide attachment points.

Mounting

Plate

Safety

Cable

Shackle

Fig. 2.2

Fig. 2.1

La page charge ...

Big Ass Fans Haiku Guide d'installation

Marque: Big Ass Fans

Modèle: Haiku

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Big Ass Fans Haiku Installation guide
español: Big Ass Fans Haiku Guía de instalación

Big Ass Fans Haiku Guide d'installation

Big Ass Fans Haiku Guide d'installation

dans d''autres langues

Documents connexes