3M DBI-SALA® Lad-Saf™ Stainless Steel Cable Lifeline, 1x7 6152050, 1 EA Mode d'emploi

Marque: 3M

Modèle: DBI-SALA® Lad-Saf™ Stainless Steel Cable Lifeline, 1x7 6152050, 1 EA

Taper: Mode d'emploi

USER INSTRUCTIONS

A Capital Safety Company

Certiﬁcate No. FM 39709

ISO

9001

ANSI Z359

ANSI A14.3

EN 353-1:2002

CSA Z259.2.1

CE TYPE TEST

No. 0320

TUV NEL

East Kilbride,

Glasgow

G75 0QU

PRODUCTION

QUALITY

CONTROL

No. 0086

BSI Product Services

Kitemark House

Mayland Ave.

Hemel Hempstead

HP2 4SQ UK

ANSI, CSA CE DESCRIPTION

6116541

(ANSI A14.3, CSA Z259.2.1)

Flex Sleeve, 8.0 mm or 9.5 mm (5/16” or 3/8”), Sleeve Only

6116540

(ANSI A14.3, CSA Z259.2.1)

Flex Sleeve, 8.0 mm or 9.5 mm (5/16” or 3/8”), w/Carabiner

6116507

(CSA Z259.2.1)

6116507

(EN353-1:2002)

Flex Sleeve, 8.0 mm or 9.5 mm (5/16” or 3/8”), w/Shock Pack & Carabiner

FORM NO: 5903085

REV: B

LAD-SAF

Detachable Cable Sleeve

Model Number: 6116507, 6116540, 6116541

FORWARD

This instruction describes installation and use of Lad-Saf

Flexible Detachable Cable Sleeve. It should

be used as part of an employee training program as required by OSHA, ANSI, CSA, CE, and AS/NZS.

WARNING: These instructions must be provided to all users and rescuers

. The user and installer of

this equipment must read and understand these instructions before use of this equipment. Follow the

manufacturer’s instructions for safety equipment used with this system. Follow these instructions for

proper use, inspection, and maintenance of this equipment. This equipment is intended to be used

as part of a complete LAD-SAF

ladder safety system. Alterations, substitutions, or misuse of this

equipment, or failure to follow instructions, may result in serious injury or death

IMPORTANT: If you have questions on the installation, use, maintenance, or suitability of this

equipment for your application, contact DBI-SALA.

IMPORTANT: Before using this equipment, record the product identiﬁ cation information from the

installation and service label in the Inspection & Maintenance Log in Section 9 of this manual.

GLOSSARY REFERENCE BOXES

Numbered Glossary Reference Boxes on the front cover of this instruction reference

the following items:

: User Instructions

: Lad-Saf Detachable Cable Sleeve

: Model Number(s)

: Standards

: Top Bracket

: Cable

: Cable Guide

: System Label with i-Safe™ RFID Tag

: Bottom

Bracket

: EC Test Performed

: Number of body checking the manufacture of this PPE

1 RESCUER: Person or persons other than the rescue subject acting to perform an assisted rescue by operation or a rescue system.

1.0 APPLICATIONS

1.1 PURPOSE: The LAD-SAF Detachable Cable Sleeve (Figure 1)arrests the fall of personnel while climbing a

ﬁ xed ladder. The Detachable Cable Sleeve is not intended to be used for material handling.

NOTE: The installer and user must ensure the ladder meets all applicable local, state, and federal

standards, including ANSI A14.3.

1.2 LIMITATIONS: The LAD-SAF Detachable Cable Sleeves must be used with a DBI-SALA approved ladder

safety system. Use only 5/16 inch (8 mm) or 3/8 inch (9.5 mm) diameter solid core cable with the

Detachable Cable Sleeve.

The Detachable Cable Sleeve must be directly connected to an approved full body harness or body belt with

the attached Carabiner (Figure 1, Item F). Do not use connection devices other than the carabiner that is

part of the Detachable Cable Sleeve

NOTE: ANSI A14.3 and OSHA 1926.1053 states that the length of connection between the carrier and

attachment point must not exceed 9 inches (23 cm).

Figure 1 - Components

A Cable

B Upper Roller

C Upper Roller

Extension

D Label

E Handle

F Carabiner

G Lower Roller

H Cable Shoe

I Gravity Stop

J Locking Lever

K Energy Absorber

L Impact Indicator

M Sleeve Body

2.0 SYSTEM REQUIREMENTS

2.1 COMPATIBILITY OF COMPONENTS AND SUBSYSTEMS: This equipment is designed for use with

DBI-SALA approved components and subsystems. The use of non-approved components and subsystems

may jeopardize compatibility of equipment and could affect the safety and reliability of the complete system.

Contact DBI-SALA if you have questions about compatibility of equipment.

3.0 OPERATION AND USE

3.1 CONNECTING THE DETACHABLE CABLE SLEEVE TO THE

CARRIER CABLE: See Figure 1 for identiﬁ cation of components

referenced in the following steps:

WARNING: In situations where a fall hazard exists, use

a back-up fall arrest system, such as a lanyard, to protect

against a fall.

Step 1. Ensure the sleeve is correctly positioned relative to

the carrier cable (Figure 2). The “up” arrow on the

sleeve must be pointing to the ascending direction. The

detachable safety sleeve includes a gravity stop (1I) to

reduce the possibility of installing the sleeve upside-down.

Step 2. Rotate the locking lever (1J) and pivot handle (1E) to its

full upright position (Figure 2). This will draw back the

cable shoe (1H) to allow insertion of the carrier cable (1A)

into the sleeve housing (1M). The locking lever is on both

sides of the Detachable Cable Sleeve for right or left hand

operation.

Step 3. Hold the sleeve upright and place the upper roller (1B)

onto the cable. See Figure 3.

Step 4. Push back the upper roller extension (1C) and insert the

cable through the slot on the side of the sleeve. Position

the cable in the sleeve recess. Release the handle (1E)

to lock the sleeve on the cable (see Figure 4). Ensure the

locking lever (1J) is in the locked position before use .

Figure 1 shows the locking lever in the locked position.

3.2 CONNECTING THE DETACHABLE CABLE SLEEVE TO THE

HARNESS OR BODY BELT: Connect the carabiner on the sleeve

to the full body harness attachment point designated for ladder

climbing. Always use the carabiner supplied on the sleeve. Do not

substitute with other connectors. Do not use other connecting

devices such as a short lanyard, chain, link, or clevis. Connection

between the sleeve and full body harness or body belt may be

done before or after the sleeve has been installed onto the carrier

cable. When connecting, ensure the carabiner gate is fully closed

and locked.

ASCENDING: To ascend the ladder climb up normally. The

Detachable Cable Sleeve will follow the climber. The cable is snapped

out of the cable guides as they are encountered. Reconnect cable

into cable guides after passing each cable guide. Do not remove the

climbing sleeve from the cable to pass the cable guides.

DESCENDING: To descend the ladder, climb down smoothly in

a normal position. Allow the sleeve to “lead” the climber down.

Climbing down out of position (leaning back excessively) will cause

the sleeve to lock on the cable. If the sleeve locks, move upward

slightly to release the sleeve and continue to descend the ladder.

When climbing is completed remove the sleeve from the cable by

rotating the locking lever and pivoting handle to its full upright

position. The sleeve can now be removed from cable and properly

stored.

Figure 2

Figure 3

Figure 4

Ensure all hazards are addressed to provide climber safety. Hazardous environments or conditions include, but

are not limited to; power lines, heat or ﬂ ame, explosive gases, physical obstructions, and climbers ability and

health. If a fall occurs the employer must have a rescue plan and the ability to implement it. After a fall the

Detachable Cable Sleeve must be inspected by a competent person other than the user. See section 5.0 of this

manual for inspection steps.

4.0 TRAINING

4.1 TRAINING: It is the responsibility of the user and purchaser of this equipment to assure they are familiar

with these instructions, operating characteristics, application limits, and the consequences of improper use

of this equipment. Users and purchasers of this equipment must be trained in the correct care and use of

this equipment.

IMPORTANT: Training must be conducted without exposing the user to a fall hazard. Training should be

repeated on a periodic basis.

Step 1. Don a full body harness or body belt and attach to Detachable Cable Sleeve.

Step 2. Ascend the ladder to approximately three feet. With both hands and feet on the climbing structure

ﬂ ex knees in a quick sitting motion to simulate a fall. This will activate the sleeve.

Step 3. Repeat Step 2. After the sleeve locks, move upward to unlock the sleeve.

Step 4. Descend the ladder and detach from the sleeve.

5.0 INSPECTION

5.1 FREQUENCY:

• Before Each Use inspect the Detachable Cable Sleeve according to sections 5.2 and 5.3.

• Formal Inspection: A formal inspection of the Detachable Cable Sleeve must be performed at least

annually by a competent person other than the user. The frequency of formal inspections should be based

on conditions of use or exposure. See sections 5.2 and 5.3. Record the inspection results in the inspection

and maintenance log in Section 9.

• After a Fall a formal inspection of the Detachable Cable Sleeve must be performed by a competent person

other than the user. Record the inspection results in the inspection and maintenance log in Section 9.

5.2 INSPECTION GUIDELINES: See Figure 1 for identiﬁ cation of the components described in the following

guidelines:

1. Inspect the handle (1E) and cable shoe (1H) for bends, cracks, and deformities. All fasteners must be

securely attached. Operation of handle and cable shoe must be free and smooth. Springs must be secure

and of sufficient strength to pull handle down.

2. Inspect the locking lever (1J) for smooth operation, ensuring it springs back into its locked position when

released.

3. Inspect the sleeve body (1M) for wear on the inside where the cable passes through.

4. Insp ect the impact indicator pin (1L). If the indicator pin is missing or damaged, the sleeve should not be

used until the pin is replaced.

5. Inspect the energy absorber(1K) to determine it has not been activated. The energy absorber cover

should be secure and free of tears or damage.

5.3 If inspection reveals an unsafe or defective condition remove the Detachable Cable Sleeve from service

and destroy or contact an authorized service center for repair. Record the results in the Inspection and

Maintenance Log in Section 9 of this manual or use the i-Safe™ inspection web portal to maintain your

inspection records (see Section 6).

6.0 I-SAFE™ RFID

6.1 I-SAFE™ RFID TAG: The Detachable Cable Sleeve has an i-Safe™ Radio Frequency Identiﬁ cation (RFID)

tag in the inside pocket on the energy absorber ﬂ ap (see Figure 5). The i-Safe™ RFID tag can be used

in conjunction with the i-Safe handheld reading device and web based portal to simplify inspection and

inventory control and provide records for your fall protection equipment. If you are a ﬁ rst-time user, contact

a Capital Safety Customer Service representative (see back cover); or if you have already registered, go to

www.capitalsafety.com/isafe.html. Follow the instructions provided with your i-Safe handheld reader or on

the web portal to transfer your data to your web log.

Figure 5 - i-Safe™ RFID Tag

7.0 MAINTENANCE, SERVICING, STORAGE

The LAD-SAF sleeve may be cleaned using commercial parts cleaning solvents and rinsed with warm, soapy

water. Light machine oil may be applied to moving parts if required. Do not use excessive oil, or allow oil to

contact cable clamping surfaces.

Clean the energy absorber with water and a mild detergent solution. Wipe off the hardware with a clean, dry

cloth and hang to air dry. Do not force dry with heat. An excessive build-up of dirt, paint, etc. may prevent

the energy absorber from working properly, and in severe cases, weaken the webbing.

Additional maintenance and servicing procedures must be completed by an authorized service center.

Authorization must be in writing.

Store the Detachable Cable Sleeve in a cool, dry, clean environment, out of direct sunlight. Avoid areas

where chemicals vapors exist. Thoroughly inspect the sleeve after extended storage.

8.0 LABELING

8.1 Labels must be securely attached and fully legible:

1. Part Number

2. Serial Number

3. WARNING: Read and follow manufacturer’s instructions supplied

with this product before use. Do not use with incompatible

cables. Use only with DBI-SALA approved system and harness.

Maximum distance allowed between system cable and harness

attachment point is 9 inches. Inspect before each use. Make

only compatible connections between sleeve and harness.

Failure to heed warnings may result in serious injury or death.

1. Part Number

2. Date Manufactured (Year/Month)

3. WARNING: Read and follow manufacturer’s instructions supplied

with this product before use. Do not use with incompatible

cables. Use only with DBI-SALA approved system and harness.

Maximum distance allowed between system cable and harness

attachment point is 9 inches. Inspect before each use. Make

only compatible connections between sleeve and harness.

Failure to heed warnings may result in serious injury or death.

1. Maximum distance allowed between system cable and harness

attachment point is 9 inches (23 cm).

2. Do not use with Lanyard.

9.0 INSPECTION AND MAINTENANCE LOG

SERIAL NUMBER:

MODEL NUMBER:

DATE PURCHASED: DATE OF FIRST USE:

INSPECTION DATE INSPECTION ITEMS

NOTED

CORRECTIVE ACTION MAINTENANCE

PERFORMED

Approved By:

9.0 INSPECTION AND MAINTENANCE LOG

SERIAL NUMBER:

MODEL NUMBER:

DATE PURCHASED: DATE OF FIRST USE:

INSPECTION DATE INSPECTION ITEMS

NOTED

CORRECTIVE ACTION MAINTENANCE

PERFORMED

Approved By:

LIMITED LIFETIME WARRANTY

Warranty to End User: D B Industries, Inc., dba CAPITAL SAFETY USA (“CAPITAL SAFETY”)

warrants to the original end user (“End User”) that its products are free from defects in materials and

workmanship under normal use and service. This warranty extends for the lifetime of the product

from the date the product is purchased by the End User, in new and unused condition, from a CAPITAL

SAFETY authorized distributor. CAPITAL SAFETY’S entire liability to End User and End User’s exclusive

remedy under this warranty is limited to the repair or replacement in kind of any defective product

within its lifetime (as CAPITAL SAFETY in its sole discretion determines and deems appropriate). No oral

or written information or advice given by CAPITAL SAFETY, its distributors, directors, ofﬁ cers, agents

or employees shall create any different or additional warranties or in any way increase the scope of

this warranty. CAPITAL SAFETY will not accept liability for defects that are the result of product abuse,

misuse, alteration or modiﬁ cation, or for defects that are due to a failure to install, maintain, or use the

product in accordance with the manufacturer’s instructions.

CAPITAL SAFETY’S WARRANTY APPLIES ONLY TO THE END USER. THIS WARRANTY IS THE ONLY

WARRANTY APPLICABLE TO OUR PRODUCTS AND IS IN LIEU OF ALL OTHER WARRANTIES AND

LIABILITIES, EXPRESSED OR IMPLIED. CAPITAL SAFETY EXPRESSLY EXCLUDES AND DISCLAIMS

ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND

SHALL NOT BE LIABLE FOR INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES OF ANY NATURE,

INCLUDING WITHOUT LIMITATION, LOST PROFITS, REVENUES, OR PRODUCTIVITY, OR FOR BODILY

INJURY OR DEATH OR LOSS OR DAMAGE TO PROPERTY, UNDER ANY THEORY OF LIABILITY, INCLUDING

WITHOUT LIMITATION, CONTRACT, WARRANTY, STRICT LIABILITY, TORT (INCLUDING NEGLIGENCE) OR

OTHER LEGAL OR EQUITABLE THEORY.

GARANTIE LIMITÉE SUR LA DURÉE DE VIE

Garantie offerte à l’utilisateur ﬁ nal : D B Industries, Inc., dba CAPITAL SAFETY USA (« CAPITAL SAFETY »)

garantit à l’utilisateur ﬁ nal d’origine (« Utilisateur ﬁ nal ») que les produits sont libres de tout défaut matériel et de

fabrication dans des conditions normales d’utilisation et de service. Cette garantie couvre toute la durée de vie du

produit, de sa date d’achat à l’état neuf et inutilisé par l’utilisateur auprès d’un distributeur agréé CAPITAL SAFETY.

La responsabilité intégrale de Capital Safety et le seul recours du Client dans le cadre de cette garantie se limitent

à la réparation ou le remplacement en nature des produits défectueux pendant leur durée de vie (à la seule

discrétion de Capital Safety et selon ce qu’elle juge approprié). Aucun renseignement ou avis oral ou écrit fourni par

CAPITAL SAFETY, ses détaillants, administrateurs, cadres, distributeurs, mandataires ou employés ne représentera

une garantie ou n’augmentera de quelque manière la portée de la présente garantie limitée. CAPITAL SAFETY

n’accepte aucune responsabilité pour les défauts causés par un abus, une utilisation abusive, une altération ou une

modiﬁ cation, ou pour les défauts causés par le non-respect des instructions du fabricant relatives à l’installation,

à l’entretien ou à l’utilisation du produit.

CETTE GARANTIE CAPITAL SAFETY S’APPLIQUE UNIQUEMENT À L’UTILISATEUR FINAL. ELLE EST LA SEULE

GARANTIE APPLICABLE À NOS PRODUITS. ELLE EXCLUT TOUTE AUTRE GARANTIE EXPRESSE OU IMPLICITE.

CAPITAL SAFETY EXCLUT EXPLICITEMENT ET DÉCLINE TOUTE GARANTIE IMPLICITE DE MISE EN MARCHÉ ET

D’ADAPTATION À DES FINS PARTICULIÈRES, ET NE SERA RESPONSABLE POUR AUCUN DOMMAGE-INTÉRÊT

DIRECT OU INDIRECT, CORRÉLATIF OU ACCESSOIRE DE TOUTE NATURE Y COMPRIS ET DE MANIÈRE NON

LIMITATIVE, LES PERTES DE PROFITS, LES REVENUS OU LA PRODUCTIVITÉ, LES BLESSURES CORPORELLES,

VOIRE LA MORT OU DOMMAGES À LA PROPRIÉTÉ, DANS LE CADRE DE TOUTE THÉORIE DE RESPONSABILITÉ, Y

COMPRIS ET DE MANIÈRE NON LIMITATIVE UN CONTRAT, UNE GARANTIE, UNE RESPONSABILITÉ (Y COMPRIS LA

NÉGLIGENCE) OU TOUTE AUTRE THÉORIE LÉGALE OU ÉQUITABLE.

GARANTÍA LIMITADA DE POR VIDA

Garantía para el usuario ﬁ nal: D B Industries, Inc., que opera bajo el nombre de CAPITAL SAFETY USA

(“CAPITAL SAFETY”) garantiza al usuario ﬁ nal original (“Usuario ﬁ nal”) que sus productos están libres de defectos

de materiales y de mano de obra en condiciones normales de uso y mantenimiento. Esta garantía se extiende

durante la vida útil del producto a partir de la fecha en que el Usuario ﬁ nal adquiere el producto, nuevo y sin

uso, a un distribuidor autorizado de CAPITAL SAFETY. La entera responsabilidad de CAPITAL SAFETY hacia el

Usuario ﬁ nal y el remedio exclusivo para el Usuario ﬁ nal bajo esta garantía están limitados a la reparación o el

reemplazo por materiales de todo producto defectuoso dentro de su vida útil (según CAPITAL SAFETY lo determine

y considere apropiado a su solo criterio). Ninguna información o asesoramiento, oral o escrito, proporcionado

por CAPITAL SAFETY, sus distribuidores, directores, funcionarios, agentes o empleados creará una garantía

diferente o adicional ni aumentará de ninguna manera el alcance de esta garantía. CAPITAL SAFETY no aceptará

responsabilidad por defectos resultantes del abuso, el uso incorrecto, la alteración o la modiﬁ cación del producto,

ni por defectos resultantes de no respetar las instrucciones del fabricante durante la instalación, el mantenimiento

o el uso del producto.

LA GARANTÍA DE CAPITAL SAFETY SE APLICA ÚNICAMENTE AL USUARIO FINAL. ESTA GARANTÍA ES LA

ÚNICA GARANTÍA QUE SE APLICA A NUESTROS PRODUCTOS Y REEMPLAZA A TODAS LAS OTRAS GARANTÍAS

Y RESPONSABILIDADES, EXPRESAS O IMPLÍCITAS. CAPITAL SAFETY EXPRESAMENTE EXCLUYE Y RENUNCIA A

TODAS LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILIDAD O APTITUD PARA UN PROPÓSITO PARTICULAR, Y

NO SERÁ RESPONSABLE POR DAÑOS INCIDENTALES, PUNITIVOS O EMERGENTES DE NINGUNA NATURALEZA,

INCLUYENDO SIN LIMITACIÓN PÉRDIDAS DE INGRESOS, GANANCIAS O PRODUCTIVIDAD; NI POR

LESIONES CORPORALES O MUERTE, O PÉRDIDA DE O DAÑO A LA PROPIEDAD, BAJO CUALQUIER TEORÍA DE

RESPONSABILIDAD, INCLUYENDO SIN LIMITACIÓN CONTRATO, GARANTÍA, RESPONSABILIDAD ESTRICTA,

AGRAVIO (INCLUIDA NEGLIGENCIA) O CUALQUIER OTRA TEORÍA LEGAL O EQUITATIVA.

ISO

9001

CSG USA & Latin America

3833 SALA Way

Red Wing, MN 55066-5005

Toll Free: 800.328.6146

Phone: 651.388.8282

Fax: 651.388.5065

solutions@capitalsafety.com

CSG Canada

260 Export Boulevard

Mississauga, ON L5S 1Y9

Phone: 905.795.9333

Toll-Free: 800.387.7484

Fax: 888.387.7484

info.ca@capitalsafety.com

CSG Northern Europe

5a Merse Road

North Moons, Moat

Reditch, Worcestershire, UK

B98 9HL

Phone: + 44 (0)1527 548 000

Fax: + 44 (0)1527 591 000

csgne@capitalsafety.com

CSG EMEA

(Europe, Middle East, Africa)

Le Broc Center

Z.I. 1ère Avenue

5600 M B.P. 15 06511

Carros

Le Broc Cedex

France

Phone: + 33 4 97 10 00 10

Fax: + 33 4 93 08 79 70

information@capitalsafety.com

CSG Australia & New Zealand

95 Derby Street

Silverwater

Sydney NSW 2128

AUSTRALIA

Phone: +(61) 2 8753 7600

Toll-Free : 1 800 245 002 (AUS)

Toll-Free : 0800 212 505 (NZ)

Fax: +(61) 2 87853 7603

sales@capitalsafety.com.au

CSG Asia

Singapore:

16S, Enterprise Road

Singapore 627666

Phone: +65 - 65587758

Fax: +65 - 65587058

inquiry@capitalsafety.com

Shanghai:

Rm 1406, China Venturetech Plaza

819 Nan Jing Xi Rd,

Shanghai 200041, P R China

Phone: +86 21 62539050

Fax: +86 21 62539060

www.capitalsafety.com

The Ultimate in Fall Protection

3M DBI-SALA® Lad-Saf™ Stainless Steel Cable Lifeline, 1x7 6152050, 1 EA Mode d'emploi

Marque: 3M

Modèle: DBI-SALA® Lad-Saf™ Stainless Steel Cable Lifeline, 1x7 6152050, 1 EA

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: 3M DBI-SALA® Lad-Saf™ Stainless Steel Cable Lifeline, 1x7 6152050, 1 EA Operating instructions

3M DBI-SALA® Lad-Saf™ Stainless Steel Cable Lifeline, 1x7 6152050, 1 EA Mode d'emploi

3M DBI-SALA® Lad-Saf™ Stainless Steel Cable Lifeline, 1x7 6152050, 1 EA Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents