WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov.2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
PD-35433
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty: 5pcs+2 Extra
AB
Mounting Screw
Qty:1 Extra
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov .2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
PD-35433
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Turn to down
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
3. Loosen the mounting screw (B) from the xture, and remove the mounting ring.
4. Secure the mounting ring to the junction box using standard junction box screws
that comes with the junction box.
Note: (i) Using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
5. Choose number of rods suitable for your application. Thread the xture wire through the rods,
swivel and canopy as shown in Fig. 1. Ensure all are tightened.
Due to limited space within the canopy, shorten the cable as necessary to make the
installation easier. Make sure to identify and label all the wiring properly before any
trimming/shortening. Fig.3
6. Connect the driver’s output wires to center cable as shown in Fig. 3, red to the red, and black to the
black, make sure that wire connectors(A) are secured. Then tuck them inside the canopy.
7. Connect the driver’s input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly
to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Secure the xture by mounting the canopy to the ring of the backplate. Turn and rotate the canopy in the direction of the arrow until
it stops. Fasten the canopy to the mounting ring using the mounting screw (B).(Fig. 1)
9. For slope ceiling application, rotate swivel at the top of the stem to ensure luminaire is aiming down (Fig. 4).
White - Neutral
Black - Hot
Red +
Black -
Red +
Black -
Canopy
Driver
Output
Input
Ø6 3/4"
Ø6 1/4"
1 3/4" 1 3/8"
Driver
Fixture
Canopy
Wire Connector
Junction box
Mounting Ring
A
Junction Box Screw
Mounting Screw
B
1x6"Rod
(ROD-I06-PC130T-BK
or ROD-I06-PC130T-CH)
3x12"Rods
(ROD-I12-PC130T-BK
or ROD-I12-PC130T-CH)
Wire
-
1
-
2
dans d''autres langues
Documents connexes
-
WAC Lighting FM-35424 Mode d'emploi
-
-
-
-
-
-
-
-
-