The Daintree® EZ Connect Wireless Integrated Sensor (WIT100)
is a small-size, luminaire-integrated sensor with wireless
communication based on the 802.15.4 standard which provides
secure and reliable communication between the luminaires in
the room. Using the WIT100 sensor in each luminaire provides
state-of-the-art distributed lighting control based on the
built-in motion sensing and daylight harvesting functionalities.
The sensor is shipped in Daintree ONE standalone mode. The
standalone mode works with pre-programmed settings to
maximize energy efciency.
The sensor can be upgraded and personalized with the
Daintree EZ Connect app available as a free download on
the Apple® App Store. The sensor can be zoned with up to
30 nearby luminaires using the EZ Connect app. Once
commissioned, the sensed information is then shared
between all luminaires. The system can be commissioned,
with the Daintree EZ connect mobile app. The app is available
for download on Apple® devices. The app allows grouping
of xtures and customization of the lighting performance
in the space.
The control of the luminaire is carried out through the digital
bus between the output of the sensor and the control input
of the luminaire’s LED driver. The digital bus also provides the
necessary supply power for the sensor. No additional wiring
or auxiliary power supply are required which helps to minimize
installation costs. When commissioned in a zone it is also
possible to adjust preferred dimming levels manually through
self-powered wireless switches (ZBT-S1AWH).
These ZBT-S1AWH self-powered and wireless dimmer switches
transmit wireless messages to the xtures using the mechanical
energy of button presses to generate all necessary power for
the electronics.
Project Name
Date Type
Catalog Number
Daintree™ Wireless Controls
WIT100 Wireless Integrated Sensor
Product Dimensions
Description
Cable from Driver/Interface module
Cable from Driver/Interface module
Sensor Pattern
The detection area
determination was
performed according to the
NEMA WD 7-2011 Standard
(Occupancy
Motion Sensors
Standard).
The detector sensitivity
was
set to the default 80%
The whole area shows
the major motion
detection eld.
The shaded area shows the minor motion
detection eld.
Compatible with
• ZigBee Green Power (included in ZigBee 3.0)
• Daintree EZ Connect controls
• ZBT-S1AWH self powered, wireless dimmer switches
Daintree™ | WIT100 Wireless Integrated Sensor
Daintree EZ Connect Benets
Technical Data
Product Specications
Dimensions: See Dimensional Diagram
Weight: 15g
Voltage Rating 20Vdc, Class 2 (SELV)
Current Consumption: Max 8mA (without digital communication) @ Max. 20V DC, Class 2
Sensor Type: Passsive infrared (PIR) sensor (for motion) and light sensor
Operating Environment: 0°C to 45°C / IP 20 – Indoor, dry location
Status indicator: Network LED (amber): Network joined / Motion is sensed
Connections: Cable connection to the Driver or Interface module
Mounting: Installs with a 22mm (0,87”) hole
Recommended Mounting Height: 10 feet (3m)
Warranty: 5 years
2
FCC Compliant
FCC ID: 2AS3F-WIT100
IC: 25008-WIT100
CAN ICES-005 (A) / NIMB-005 (A)
Product Certications
E486320
For a complete list of the harmonized standards
that this product is in conformity with, please see
this product’s EU Declaration of Conformity on
gecurrent.com Note: Any external cables connected to devices not to exceed 3 meters length.
Additional Information
Purpose of the Control: Operating Control
Method of Mounting Control: Independently Mount Control.
Model WIT100 intended for
ush mounting into a recessed
cavity
Type of Action and Additional Features: Type 1
Control of Pollution Degree: 2
Function/Software Class and Structure: Class A
Rated Impulse Voltage: 330V
Easy Commissioning:
Daintree EZ Connect mobile app simplies and reduces the
installation process, minimizing disruption to enterprise
operations.
Intuitive Deployment:
Daintree EZ Connect mobile app recognizes xtures that
are closest to the installer, so xtures are easily identied
making the commissioning more efcient.
Zoned Communication:
Fixtures can be zoned and the sensors talk to each other to
react in concert with each other to occupancy, daylight and
wall controls.
Simplicity:
Integration with xtures reduces the amount of devices that
need to be installed in a room.
Room Based Control:
Customize the lighting parameters to the task that is being
performed in the application space.
Code Compliant:
Integrated wireless sensors offer daylight harvesting and
granular lighting controls.
Daintree™ | WIT100 Wireless Integrated Sensor
3
Cable Connection to Driver
• Connect the WIT100 Sensor’s digital power bus line with the connectors to compatible devices and interface module.
• CE Power Supply Compatibility List: Vossloh-Schwabe Ref. No. 186738 and 186740
• Please contact customer support for the full list of compatible devices.
Mains
Input
Fixture
Digital Power Bus
(Power +2-Way Data)
WIT100
Cable from Driver/Interface module
Control Ready Driver
Commissioning the WIT 100 Sensor
Commissioning the sensor is easy on the Daintree EZ Connect app.
The app is available for download on the Apple® App Store.
Product Availability
95037451 Wireless Integrated Sensor WIT100
SKU DESCRIPTION ARTICLE NO.
Designed in the USA & Hungary by
GE current a Daintree company
WIRELESS CONTROLS
www.gecurrent.com
T 1-888-694-3533
© 2020 Current Lighting Solutions, LLC GE and the GE monogram are
trademarks of the General Electric Company and are used under license.
Information provided is subject to change without notice. All values are
design or typical values when measured under laboratory conditions
DT026 (Rev 10/23/20)
Daintree™ | WIT100 Wireless Integrated Sensor
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
• This device may not cause interference.
• This device must accept any interference, including interference
that may cause undesired operation of the device.
Cet appareil est conforme à la partie 15 des règles FCC. Son
fonctionnement est soumis aux deux conditions suivantes: (1) Cet
appareil ne doit pas causer d’interférences nuisibles, et (2) cet appareil
doit accepter toute interférence reçue, y compris les interférences
susceptibles de provoquer un fonctionnement indésirable.
•
L’appareil ne doit pas produire de brouillage;
•
L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
To satisfy FCC/ISED RF exposure requirements a separation
distance of 20 cm or more must be maintained between the
antenna of this device and persons during operation. Operation
at closer than 20cm is not permitted.
Pour être conforme aux limites d’exposition aux ondes RF des
normes FCC/ISED, une distance de séparation d’au moins 20 cm
doit être maintenue entre l’antenne de cet appareil et tou te
personne pendant son opération. Mettre en opération cet appareil
a une distance plus rapprochée que 20 cm n’est pas permis.
FCC/IC Compliance Statements
Caution: The user is cautioned that changes or
modications not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment
and receiver.
— Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV
technician for help
Suppliers Name: Current Lighting Solutions, LLC
Suppliers Address (USA): 1975 Noble Road, East
Cleveland, OH 44112
Suppliers phone number and / or internet contact
information: 1-800-327-0097
-
1
-
2
-
3
-
4
dans d''autres langues
- English: Daintree WIT100 User manual
Documents connexes
Autres documents
-
GE current WOS3-PC Guide d'installation
-
GE current DT044 Guide d'installation
-
Lumination RPL Series Controls Accessory Controller Bracket Guide d'installation
-
GE current IND183 Guide d'installation
-
-
-
Otterbox 78-80734 Manuel utilisateur
