Balt 91776-XXXX-XX Assembly Instructions

Taper
Assembly Instructions
Single Pedestal with Laminate Top
UPDATED AS OF: 12/02/2021
**DISCARD THIS INSTRUCTION IF USING WITH DESK**
1 of 6
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
Parts
UPDATED AS OF: 12/02/2021 2 of 6
P1 - Top
P2 - Pedestal Box
P3 - Handle
P4 - Divider Panel
P5 - Divder Bar
P6 - Pencil Tray
P7 - Key Set
x1
x1
x3
x1
x1
x1
x1
A - Pedestal Caster
Locking
B - Pedestal Caster
Non - Locking
C - Caster Screw
D - Wood Screw
E - Plastic Side Cap
F - Plastic Back Cap
x2
x2
x4
x5
x8
x6
Hardware
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
UPDATED AS OF: 12/02/2021 3 of 6
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
complètes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient serrées.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 12/02/2021 4 of
STEP 2
Open shelves and remove handle screws. Swap handles to front of shelves and insert
handle screws from inside of shelves to secure handles in place.
Remove shelves by first extending shelf to furthest setting until catch engages. To slide
shelf off of rails, rotate visible catch levers on both sides of shelf either up or down while
gently pulling shelf. Once both sides are free, shelf can be removed.
STEP 3
UPDATED AS OF: 12/02/2021 5 of 6
STEP 4
Set pedestal (with shelves removed) upside down on top.
Secure to top with wood screws inserted through holes in
pedestal top brackets.
Install Casters to bottom of pedestal. Use Locking Casters in front of pedestal and
Non-Locking Casters in the back. Secure casters with screws.
A
B
C
D
STEP 5
UPDATED AS OF: 12/02/2021 6 of 6
Insert shelves back in pedestal. Place file accessories
in desired location within shelves. (Optional: Push plastic
caps into threaded inserts on either side of pedestal).
THIS COMPLETES ASSEMBLY INSTRUCTION
STEP 6
Optionally customer may choose to plug side and back holes with Plastic Side
Caps (E) and Back Caps (F). Extra caps are included.
E
F
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Balt 91776-XXXX-XX Assembly Instructions

Taper
Assembly Instructions

dans d''autres langues