Samsung Electronics WBA210M Manuel utilisateur

WBA210M
Samsung Electronics
Marque
Samsung Electronics
Modèle
WBA210M
Taper
Manuel utilisateur
User Manual
1. Device name : VD BT Module
2. Model name : WBA210M
3. General Information
Shape : PCBA Module type
Comm. Protocols : BLE
Weights & Dimensions : Width 26 * Depth 49 * Height 2.7 mm
Product Weight : approximately 5g
Operating Temp : 0 ~ 40︒C
Power Source : External DC 3.3V
The WBA210M is a BLE Transceiver for Home automation networks.
Connected to the TV-remote control device, it acts as a pathway between remote home automation.
Power is provided by External 3.3V power supply with 14pin zip type connector.
Networking
The WBA210M is applied UE878 BLE Transceiver of Universal Electronics.
The BLE transceiver delivers the information received from the remote control device to the main
board with 14pin zip type connector.
Power Source
The WBA210M is powered by an external 3.3VDC@500mA regulated power source with
14pin zip type connector..
Indication
A general-purpose Red LED is used to communicate various BLE transceiver states.
Expansion Ports
The 14pin zip type connector connects the main control board.
4. Electrical Properties
Parameter
Description
Modulation type
GFSK
Modulation rate
1Mbps
Channel interval
2MHz
Antenna gain(Chip Antenna)
1.35dBi
Occupancy bandwidth ≤2MHz
frequency range 2400MHz~2483.5MHz
Carrier frequency tolerance ≤20×10-6
OEM/Integrators Installation Guide
Important Notice to OEM integrators
1. This module is limited to OEM installation ONLY.
2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b).
3. The separate approval is required for all other operating configurations, including portable configurations with
respect to Part 2.1093 and different antenna configurations
4. F r FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional testing to verify compliance
as a composite system. When testing the host device for compliance with Part15 Subpart B, the host
manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are
installed and operating. The modules should be transmitting and the evaluation should confirm that the
module's intentional emissions are compliant (i.e. fundamental and out of band emissions).
The host manufacturer must verify that there are no additional unintentional emissions other than what is
permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s).
The Grantee will provide guidance to the host manufacturer for Part 15 B requirements if needed.
Antenna Installation
(1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
(2) The transmitter module may not be co-located with any other transmitter or antenna.
(3) Only antennas of the equal or less gains as 1.35dBi may be used with this module
When using an antenna higher than the gain mentioned above, the conducted oputput power must be reduced,
and the product may require C2PC filing with additional tests and RF exposure evaluation.
In the event that these conditions cannot be met (for example higher than max gain or co-location with another
transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate FCC/IC authorization.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module. The end user
manual shall include all required regulatory information/warning as show in this manual.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device is intended only for OEM integrators under the
following conditions: (For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
End Product Labeling
When the module is installed in the host device, the FCC ID label must be visible through a window on the final
device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be
placed on the outside of the final device that contains the following text: “Contains FCC ID: A3LWBA210M” The
FCC ID can be used only when all FCC compliance requirements are met.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
List of applicable FCC rules
This module has been tested and found to comply with part 15.247 requirements for Modular Approval.
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the
grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to
the host not covered by the modular transmitter grant of certification. If the grantee markets their product as
being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee
shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with
the modular transmitter installed.
Industry Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement."
The device could automatically discontinue transmission in case of absence of information to transmit, or
operational failure. Note that this is not intended to prohibit transmission of control or signaling information or
the use of repetitive codes where required by the technology.
L'appareil peut interrompre automatiquement la transmission en cas d'absence d'informations à transmettre
ou de panne opérationnelle. Notez que ceci n'est pas destiné à interdire la transmission d'informations de
contrôle ou de signalisation ou l'utilisation de codes répétitifs lorsque cela est requis par la technologie.
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les
utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Cet appareil est conçu uniquement pour les intégrateurs OEM dansles
conditions suivantes: (Pour utilisation de dispositif module)
This device is intended only for OEM integrators under the following
conditions: (For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son
produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or colocation with
another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used
on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du
Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans
ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur)
et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm
may be maintained between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains IC: 649E-WBA210M”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne
peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les
utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 649E-WBA210M".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à
la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui
intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Samsung Electronics WBA210M Manuel utilisateur

WBA210M
Samsung Electronics
Marque
Samsung Electronics
Modèle
WBA210M
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents