Balt SD-AJ42R-BUTCHER Assembly Instructions

Taper
Assembly Instructions
Akt Tables (36”H and 42H)
UPDATED AS OF: 09/15/2021 1 of 8
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
A - 1/4-20 x 3.5” Torx
B - 1/4-20 x 2.5” Torx
C - 1/4-20 x 1” Torx
D - #10 x 1” Phillips
E - Lock Washer
P1 - Table Top
P2 - Round Leg
P3A - Locking Caster
P3B - Non Locking Caster
P4 - Outer Corner
P5 - Inner Corner
Parts List - Round Leg Table
UPDATED AS OF: 09/15/2021 2 of 8
x1
x4
x2
x2
x4
x4
Hardware
P6 - Long Crossbar
P7 - Short Crossbar
P8 (1) - Left Leg Bracket
P9 (2) - Right Leg Bracket
P10 - Plastic Cover
x4
x12
x8
x40
x4
x1
x2
x2
x2
x6
P1 - Table Top
P2 - Rectangular Leg
P3A - Locking Caster
P3B - Non Locking Caster
P4 - Outer Corner
P5 - Inner Corner
Parts List - Rect. Leg Table
UPDATED AS OF: 09/15/2021 3 of 8
x1
x4
x2
x2
x4
x4
P6 - Long Crossbar
P7 - Short Crossbar
P8 (1) - Left Leg Bracket
P9 (2) - Right Leg Bracket
P10 - Small Plastic Cover
P11 - Large Plastic Cover
x1
x2
x2
x2
x2
x4
B - 1/4-20 x 2.5” Torx
C - 1/4-20 x 1” Torx
D - #10 x 1” Phillips
E - Lock Washer
P1 - Table Top
P2 - Round Leg
P3A - Locking Caster
P3B - Non Locking Caster
P4 - Outer Corner
P5 - Inner Corner
Hardware
x16
x8
x40
x4
For full product warranty details, please visit:
Para obtener información sobre la garantía del producto, consulte este sitio (ingles):
Pour plus d’informations sur la garantie du produit, consultez ce site (anglais):
For questions on assembly or missing/damaged parts, please contact us using the
following information.
Para preguntas sobre el ensamblaje o piezas faltantes o dañadas, por favor
contáctenos usando la siguiente información.
Pour toute question sur le montage l-assamblage manquantes ou endommagées,
veuillez nous contacter en utilisant les l’information ci-dessous.
To register your product for warranty, please visit:
Para registrar la garantía del producto, vea este sitio (en ingles):
Pour enregistrer la garantie de votre produit, consultez ce site (en anglais):
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
WARRANTY
CARE & MAINTENANCE
PRODUCT REGISTRATION
UPDATED AS OF: 09/15/2021 4 of 8
Phone:
1.800.749.2258
(Monday – Friday, 8AM – 5PM
Central Time)
http://moorecoinc.com/warranty
https://moorecoinc.com/register
Email:
support@moorecoinc.com
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
complètes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient serrées.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 09/15/2021 5 of 8
STEP 2
After placing plastic inserts into frame corners as shown, insert Leg from outside and
secure with screw (B) from inside frame, tightening into Leg until snug. Use screws
with unpainted heads for this step.
P5
P4
BP2
P7
A
P6
P10
P7
B
P6
P10
ROUND
RECTANGULAR
Attach short and long crossbars as shown, capping Long Crossbar ends with Plastic
Cover before binding at either end with 2 screws (A for Round, B for Rectangular).
STEP 3
UPDATED AS OF: 09/15/2021 6 of 8
Snap on additional Plastic Covers to exposed ends of Short Crossbars before
screwing on Leg Brackets with 2 screws (B) each. Note positions of Left and Right
Brackets depicted below. Brackets will be marked with “1” or “2” which should be
right side up throughout assembly and attached to appropriate end.
P8
P8
P9
P9
P10
B
P9
P11
B
P9
P8
P8
ROUND
RECTANGULAR
P8 P9
12
STEP 4
UPDATED AS OF: 09/15/2021 7 of 8
Keeping footrest in same position as previous step (“1” and “2” should NOT be upside
down), lower between legs. Aligning Leg Brackets with inside holes on legs, secure to legs
with 2 screws (C) per leg. Note that footrest will only fit onto legs one way so if unable to
align holes, return to previous step and carefully read instructions.
C
STEP 5
UPDATED AS OF: 09/15/2021 8 of 8
Attach legs directly to top with 10 wood screws (D) per leg.
THIS COMPLETES ASSEMBLY INSTRUCTION
P3B
STEP 6
Insert all 4 Casters by screwing into legs with lock washers (E). Install Locking Casters on
same side of table for easier access.
D
P3A
E
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Balt SD-AJ42R-BUTCHER Assembly Instructions

Taper
Assembly Instructions

dans d''autres langues