Chief PAC800E Guide d'installation

Catégorie
Supports de projecteur
Taper
Guide d'installation
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
PAC800E
PAC810E
IntelliSHOT
®
Video Conferencing Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PAC800E/810E
PAC800E/810E Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
Chief® and IntelliSHOT® are registered trademarks of Legrand
AV Inc.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems/
accessories are properly assembled and installed using the
instructions provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all equipment and accessories mounted on the PAC800E/
810E does not exceed 10 lbs (4.54 kg).
WARNING: Use of this accessory will decrease the weight
capacity of the mounting system to which it is attached by the
combined weight of the accessory and all components
supported by this accessory! See Figure below for reference.
WARNING: RISK OF INJURY TO PERSONS! Do not use
this accessory to support video equipment such as
televisions or computer monitors.
WARNING: Do not use this accessory outdoors.
--SAVE THESE INSTRUCTIONS--
standard weight limit of mounting system -
(weight of PAC800E/810E bracket + bracket components)
10 lbs (4.5 kg)
Installation Instructions PAC800E/810E
3
DIMENSIONS
PAC800
PAC810
PAC800E/810E Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions PAC800E/810E
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
5/32" 1/4"
A (1)
C (2)
E (2)
[Main bracket]
1/4-20"
1/4-20 x 1/2" D (2)
1/4-20 x 3/4"
B (1)
5/32"
(PAC800E shown)
PAC800E/810E Installation Instructions
6
Installation
NOTE: The PAC800/810E video conferencing shelf can be
mounted before or after the display is mounted to the
faceplate. It may be mounted above or below the
display.
Attach to Faceplate
1. Position main bracket (A) above or below the faceplate
making sure to line up the holes on the bracket with the
holes on the faceplate. (See Figure 1) or (See Figure 2)
2. Install two 1/4-20 x 3/4" button head cap screws (D) through
holes in bracket (A) and faceplate. (See Figure 1) or (See
Figure 2)
3. Thread two 1/4-20" lock nuts (E) onto screws (D) to secure
bracket (A) to faceplate. (See Figure 1) or (See Figure 2)
Figure 1
Figure 2
Installing Camera (not included)
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight
mounted on the
PAC800E/810E does not exceed 10 lbs (4.5
kg)
.
1. Use two 1/4-20 x 1/2" Phillips pan machine screws (C) to
secure camera to main bracket (A). (See Figure 3)
Figure 3
1
(A)
3
(D) x 2
(E) x 2
2
faceplate
(Above Install)
(PAC800E shown)
(Below install)
(D) x 2
2
faceplate
3
(E) x 2
1
(A)
(PAC800E shown)
2
(C) x 2
Camera
(not included)
(PAC800E shown)
(A)
Installation Instructions PAC800E/810E
7
Adjustments
Height Adjustment
1. Loosen two adjustment knobs on the back of the main
bracket (A). (See Figure 4)
2. Raise or lower bracket to desired height. (See Figure 4)
3. Tighten two adjustment knobs on the back of the bracket
until mount is secure. (See Figure 4)
Figure 4
123
(PAC800E shown)
2
PAC800E/810E Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003234 Rev01
2020 Legrand | AV
www.legrandav.com
12/2020
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief PAC800E Guide d'installation

Catégorie
Supports de projecteur
Taper
Guide d'installation

dans d''autres langues