Access Lighting 24900LEDD-MWH/ACR Manuel utilisateur

Access Lighting
Marque
Access Lighting
Modèle
24900LEDD-MWH/ACR
Taper
Manuel utilisateur
WHAT YOU NEED
• Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
INSTALLATION INSTRUCTIONS
WHAT WE PROVIDE
• Mounting Hardware
• Metal with Acrylic shade
• LED
COLLECTION
1
CERTIFICATION: cULus DRY
NO. 52067LEDD/52068LEDD
ANELLO
52067LEDD
52068LEDD
APPLICATION MODEL NO.
PENDANT
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that
you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care, are factors that can’t be built into any product. These factors must
be supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
Recognized.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
Recommended Dimmers
(0-10V) Any 0-10V Dimmer
(ELV) LUTRON Diva DVELV-300P
(ELV) LUTRON Maestro CL MACL-153M
(ELV) LUTRON Skylark Contour CTCL-153P
(TRIAC) LEVITON Decora Sureslide 6672
(TRIAC) LEVITON Decora Sureslide 6674
(TRIAC) LUTRON Diva DVCL-153P
(TRIAC) LUTRON Skylark CL SCL-153 or SCL-153P
MOUNT THE MOUNTING BRACKET
If there is an existing fixture remove it. Align the mounting
bracket to the junction box and with a pencil, mark the
location of the drywall anchors. Drill a hole and insert the
supplied drywall anchors. Secure the mounting bracket to
the junction box and drywall anchors with the supplied
screws.
MAKE WIRE CONNECTION AND
MOUNT
THE CANOPY TO THE MOUNTING BRACKET
Expose the supply wires from the J-box. Gently pull the
supply wires through the hole in the mounting bracket.
Connect the black supply wire to the black driver wire.
Secure with the supplied wire nuts. Connect the white supply
wire to the white driver wire. Secure with the supplied wire
nuts. Attach the green J-Box wire around green hexagonal
head screw or connect it to the green supply grounding wire
of the fixture. Secure all wires with electrical tape (not
supplied). Tuck all wires carefully into the J-Box. If not
connecting to 0-10V dimmer, cap off the Grey and Purple
wires with supplied wire nuts. Align the fixture
canopy to the
mounting bracket and secure with the supplied screws.
1
WHAT YOU NEED
• Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
2
2
CERTIFICATION: cULus DRY NO.
52067LEDD/
52068LEDD
3
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS LIGHTING FIXTURE
If the fixture is to be removed or replaced,
please ensure that the electricity is
switched off and that the fitting is cool
before touching it.
CAUTION
VER: 21.10.1
L
N
  • Page 1 1
  • Page 2 2

Access Lighting 24900LEDD-MWH/ACR Manuel utilisateur

Access Lighting
Marque
Access Lighting
Modèle
24900LEDD-MWH/ACR
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents