Firman W01782 Manuel utilisateur

P/N:317745451 Rev:06

PORTABLE INVERTER GENERATOR

Record product information to reference when ordering parts or

obtaining warranty coverage.

MODEL NUMBER

W01782

Rev Level:00

OPERATOR’S MANUAL

Table of Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety Precautions . . . . . . . . . . . . . . . . . . . . .2

Unpacking The Generator. . . . . . . . . . . . . . .6

Parts Included. . . . . . . . . . . . . . . . . . . . . .6

Controls and Features. . . . . . . . . . . . . . . . . 7

Generator. . . . . . . . . . . . .. . . . . . . . . . . . . .7

Control Panel. . . . . . . . . . . . . . . . . . . . . . . 8

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 9

Add Engine Oil . . . . . . .. . . . . . . . . . . . . . . .10

Low Oil Shutdown . . . . . . . . . . . . . . . . . . . .10

Add Fuel . . . . . . .. . . . . . . . . . . . . . . . . . . . .10

Grounding. . . . .. . . . . . . . . . . . . . . .. . . . . .11

System.. . . . . . . . . . . . . . . . . . . . . . .. . . . . .12

Operation . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 12

Generator Location . . . . . . . . . . . . . . . . . . 12

Surge Protection . . . . . . . . . . . . .. . . . . . . .13

Starting the Generator. . . . . . . . . .. . . . . . 13

Connecting Electrical Loads . . . . . . . .. . . 14

Economy Control Switch. . . . . . . .. . . . . . 15

12V DC Outlet (Battery Charger).. . . . . . 15

Stopping the Engine . . . . . . . . . . . . . . . . . 16

Low Oil Shutdown . . . . . . . . . . . . . . . . . . 17

Do Not Overload Generator . . . . . . . . . . . 17

Parallel Operation. . . . . . . . . . . . . . . . . . . 17

Maintenance And Storage. . . . . . . . . . . . . . 18

Maintenance Schedule . . . . . . . . . . . . . 18

Engine Maintenance .. . . . . . . . . . . .. . . . 19

Change Engine Oil . . .. . . . . . . . . . . . . . 19

Air Filter Maintenance. . . . . . . . . . . . . .19

Spark Plug Maintenance. . . . . . . . . . . . 20

Cleaning Fuel Strainer . . . . . . . . . . . . 20

. . . 20

Generator Maintenance . . . . . . . . . . . . . . 21

Service and Storage . . . . . . . . . . . . . . . .. 22

Introduction

Inspect Muffler and Spark Arrester

Connecting to a Building’s Electrical

English Customer Service: 1-844-FIRMAN1

. . . . . . . . . . . . . . . . . . . . .23

Parts / List/ Wiring diagram . . . . . . . . . . 24

Generator Parts Diagram . . . . . . . . . . . . 24

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . 25

Engine Parts Diagram . . . . . . . . . .. . . . . 26

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . 27

Wiring diagram. . . . . . . . . . . . .. . . . . 28

Service Information . . . . . . . . . . . . . .. . . . . 29

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Trouble Shooting

Thank you for purchasing a FIRMAN generator.

This manual covers operation and maintenance of the FIRMAN generators. All information in this

publication is based on the latest production information available at the time of approval for printing.

The manufacturer reserves the right to change, alter or other wise improve the generator and this

documentation at any time without prior change.

Page 01

This manual contains safety information to make you aware of the hazards and risks associated

with generator products and how to avoid them. This generator is designed and intended only

for supplying electrical power for operating compatible electrical lighting, appliances, tools and

motor loads, and is not intended for any other purpose. It is important that you read and

understand these instructions thoroughly before attempting to start or operate this equipment.

Save these original instructions for future reference.

Important Safety Information

The manufacturer cannot possibly anticipate every possible circumstance that might involve a

hazard. The warnings in this manual and the tags and decals affixed to the unit are therefore not

all-inclusive. If you use a procedure, work method or operating technique that the manufacturer

does not specifically recommend you must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure work method or operating technique that you choose

does not render the generator unsafe.

SAFETY INFORMATION

DANGER WARNING CAUTION

Toxic Fumes

Fire Hazard

Hot Surface.

Do Not Touch the Surface.

Kickback

Risk of Electric Shock

Explosion Hazard

Rotating Parts Entanglement

Hazard

Operator’s Manual

INTRODUCTION

English Customer Service: 1-844-FIRMAN1

Indicates a hazard

which, if not avoided,

will result in death or

serious injury.

Indicates a hazard

which, if not avoided,

could result in death

or serious injury.

Indicates a hazard

which, if not avoided,

could result in minor or

moderate injury.

SAFETY PRECAUTIONS

Page 02

POISONOUS GAS HAZARD.

•

English Customer Service: 1-844-FIRMAN1

DANGER

Page 03

CORRECT USAGE

Example location to reduce risk of carbon monoxide poisoning

•ONLY use outside and downwind, far away from windows, doors and vents.

•Direct exhaust away from occupied spaces.

INCORRECT USAGE

Do not operate in any of the following locations:

Near any door, window or vent

Garage

Basement

Crawl Space

Living Area

Attic

Entry Way

Porch

Mudroom

English Customer Service: 1-844-FIRMAN1

Page 04

English Customer Service: 1-844-FIRMAN1

WHEN OPERATING EQUIPMENT

DO NOT operate this product inside any

building, carport, porch, mobile equipment,

marine applications, or enclosure.

•

DO NOT tip engine or equipment at angle

which causes fuel to spill.

DO NOT stop engine by moving choke

control to “Start” position.

•

WHEN TRANSPORTING, MOVING

OR REPAIRING EQUIPMENT

Transport/move/repair with fuel tank

EMPTY or with fuel shutoff valve OFF.

•

•DO NOT tip engine or equipment at angle

which causes fuel to spill.

Disconnect spark plug wire.

•

WHEN STORING FUEL OR EQUIPMENT

WITH FUEL IN TANK

•Store away from furnaces, stoves, water

heaters, clothes dryers, or other appliances

that have pilot light or other ignition source

because they could ignite fuel vapors.

WARNING

This generator does not meet U. S. Coast

Guard Regulation 33CFR-183 and should not

be used on marine applications.

•

•Failure to use the appropriate U. S. Coast

Guard approved generator could result in

death or serious injury.

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

WARNING

Starter cord kickback (rapid

retraction) will pull hand and arm

toward engine faster than you can

let go which could cause broken

bones, fractures, bruises, or

sprains resulting in serious injury.

When starting engine, pull cord slowly until

resistance is felt and then pull rapidly to

avoid kickback.

•

•NEVER start or stop engine with electrical

devices plugged in and turned on.

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire,

or explosion resulting in death or serious

injury.

WHEN ADDING OR DRAINING FUEL

Turn generator engine OFF and let it cool at

least 2 minutes before removing fuel cap.

Loosen cap slowly to relieve pressure in tank.

Fill or drain fuel tank outdoors.

•

•DO NOT overfill tank. Allow space for fuel

expansion.

If fuel spills, wait until it evaporates before

starting engine.

•

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap, and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke.

•

WHEN STARTING EQUIPMENT

Ensure spark plug, muffler, fuel cap, and air

cleaner are in place.

•

DO NOT crank engine with spark plug

removed.

•

Page 05

English Customer Service: 1-844-FIRMAN1

WARNING

Unintentional sparking

could cause fire or

electric shock resulting

in death or serious

injury.

WHEN ADJUSTING OR MAKING REPAIRS TO

YOUR GENERATOR

Disconnect the spark plug wire from the

spark plug and place the wire where it cannot

contact spark plug.

•

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

•DO NOT check for spark with spark plug

removed.

•

WARNING

Starter and other rotating parts

could entangle hands, hair,

clothing, or accessories

resulting in serious injury.

NEVER operate generator without protective

housing or covers.

DO NOT wear loose clothing, jewelry or

anything that could be caught in the starter

or other rotating parts.

Tie up long hair and remove jewelry.

•

Excessively high operating speeds could result

in minor injury. Excessively low operating speeds

impose a heavy load.

DO NOT tamper with governor spring, links or

other parts to increase engine speed.

Generator supplies correct rated frequency

and voltage when running at governed speed.

DO NOT modify generator in any way.

•

DO NOT exceed the generator’s wattage

amperage capacity.

Start generator and let engine stabilize

before connecting electrical loads.

NOTE:

•

CAUTION

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices

connected to it.

Connect electrical loads in OFF position,

then turn ON for operation.

Turn electrical loads OFF and disconnect

from generator before stopping generator.

•

DO NOT use generator with electrical cords

which are worn, frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or

wet weather.

DO NOT handle generator or electrical

cords while standing in water, while

barefoot, or while hands or feet are wet.

DO NOT allow unqualified persons or

children to operate or service generator.

•

WARNING

Exhaust heat/gases could ignite combustibles,

structures or damage fuel tank causing a fire,

resulting in death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot

exhaust gases.

Allow equipment to cool before touching.

It is a violation of California Public Resource

Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust

system is equipped with a spark arrester, as

defined in Section 4442, maintained in

effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for the exhaust system installed on

this engine.

Replacement parts must be the same and

installed in the same position as the original

parts.

•

DO NOT touch bare wires or receptacles.

•

Page 06

•

Use generator only for intended uses.

If you have questions about intended use,

ask dealer or contact local service center.

Operate generator only on level surfaces.

DO NOT expose generator to excessive

moisture, dust, dirt, or corrosive vapors.

DO NOT insert any objects through cooling

slots.

If connected devices overheat, turn them off

and disconnect them from generator.

Shut off generator if:

-Electrical output is lost.

-Equipment sparks, smokes, or emits flames.

-Unit vibrates excessively.

•

WARNING

Medical and Life Support Uses.

In case of emergency, call 911 immediately.

NEVER use this product to power life support

devices or life support appliances.

NEVER use this product to power medical

devices or medical appliances.

Inform your electricity provider immediately

if you or anyone in your household depends

on electrical equipment to live.

Inform your electrical provider immediately

if a loss of power would cause you or anyone

in your household to experience a medical

emergency.

•

NOTE:

Improper treatment of generator could damage

it and shorten its life.

UNPACKING THE GENERATOR

Open carton and Remove packaging materials.

Remove generator, accessories boxes, and

literature from carton. If any items are missing

or damaged, contact our product service

department at 1-844-347-6261.

•

Parts Included

Your gasoline powered inverter generator ships

with the following parts:

English Customer Service: 1-844-FIRMAN1

1. Engine Oil(Bottle) . . . . . . . . . . . . . . . . . . . . . . . 1

2. Oil Funnel . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . 1

3. Wrench for Spark Plug . . . . . . . . . . . . . . . . . . . .1

4. Screw Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

5. Battery Charge Cable . . . . . . . . . . . . . . . . . . . . .1

6. Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

7. Quick Reference Guide . . . . . . . . . . . . . . . . . . . 1

8. Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2

1

Quick

Reference

Guide

3

Manual

7

6

4

5

8

Page 07

CONTROLS AND FEATURES

Generator

*We are always working to improve our products. Therefore, the enclosed product may differ

slightly from the image on this page.

1

1-

2- Fuel Lever Vent – Turn this valve to the “On” position to supply air to the tank.

3- Fuel Cap

4- Control Panel

5- Recoil Starter

6- Muffler/Spark Arrester

7- Spark Plug Access Cover

8- Maintenance Cover – Oil filler and air filter access.

9- Choke Knob

10- Engine ON/OFF Switch

11- Economy Control Switch

Carrying Handle

English Customer Service: 1-844-FIRMAN1

①②③

④⑤

⑥

⑦

⑧

⑨

⑩

⑪

Page 08

Control Panel

Engine Switch – Flip the switch to the “ON”

position and pull the recoil starter to start

the generator. Turn to the “OFF” position to

turn off the generator.

1

2

3

4

6

Ground Terminal – Consult an electrician for local

grounding regulations.

120V, 20A Duplex – (NEMA 5-20R) 20 Amp of current

may be drawn from this 120 Volt receptacle.

Total power drawn from all receptacles must not exceed the name plate rating.

NOTE:

Outlet Cover - Protect the receptacles from dust

and debris.

English Customer Service: 1-844-FIRMAN1

1

3

2

4

56

7

8

9

10

11

12

13

14

12V DC outlet – 5 Amp of DC current may be drawn

from this receptacle.

Use this outlet to charge 12V automotive type

batteries ONLY. See 12V DC outlet (Battery

Charger) section.

Parallel Operation Outlets - These outlets are used

for connecting two FIRMAN inverter generators for

parallel operation. A FIRMAN parallel kit(optional

equipment) is required for parallel operation.

DC Circuit Breaker - The circuit protector may be reset

by pushing the button of the protector.

5

7

Oil Warning Indicator Light – Check oil level when

this light turns “ON”. Engine will not run when

indicator is lit.

8Overload Indicator Light – This light turns “ON”

when the generator is overloaded and will cut

power to the receptacles.

9

Output Ready Indicator Light – Remains “ON”

during normal operating conditions. Shuts “OFF”

when generator is overloaded.

10

11

Choke Knob

Economy Control Switch

12

The Economy Control switch can be activated in order to

minimize fuel consumption and noise while operating the

unit during times of reduced electrical output, allowing

the engine speed to idle during periods of non-use. The

engine speed returns to normal when an electrical load is

connected. When the economy switch is off, the engine

runs at normal speed continuously.

13

14 Fuel Valve Knob

5V USB Outlet

15

15 Recoil Stater

When the oil falls below the minimum level, the oil

warning indicator light comes on and the engine

stops automatically. The engine will not start until

the proper amount of oil is in the crank case.

The green AC Power Indicator Light comes on

when the engine starts and generates power.

If the engine overload indicator light comes on, the

generator’s wattage / amperage capacity has been

exceeded by connected electrical devices or by a

power surge. When this occurs, the green AC Power

Indicator Light(Item 7) will go off. The engine will

continue to run, but the red Engine Overload Indicator

Light will stay on and power will no longer be supplied

to connected electronic devices.

Page 09

SPECIFICATIONS

AN IMPORTANT MESSAGE ABOUT TEMPERATURE:

Your Firman Power Equipment product is designed and rated for continuous operation at

ambient temperatures up to 40°C (104°F). When your product is needed, your product may be

operated at temperatures ranging from -15°C (5°F) to 50°C (122°F) for short periods. If the

product is exposed to temperatures outside this range during storage, it should be brought back

within this range before operation. In any event, the product must always be operated outdoors,

in a well-ventilated area and away from doors, windows and other vents.

When operated above 77°F(25°C) there may be a decrease in power.

Maximum wattage and current are subject to and limited by such factors as fuel BTU content

ambient temperature, altitude, engine condition and etc. Maximum power decreases about

3.5% for each 1,000 feet above sea level; and will also decrease about 1% for each 10°F(6°C)

above 60°F(16°C) ambient temperature.

•

English Customer Service: 1-844-FIRMAN1

Model

Rated AC Voltage

Phase

Power Factor

Voltage regulator

Alternator Type

Running Watts

Starting Watts

Engine

Engine Type

Displacement

Low Oil Shutdown

Ignition System

Starting System

Fuel

Capacity Fuel Tank

Lubricating Oil Capacity

Carburetor Type

Air Cleaner

P.T.O. shaft rotation

120V

W01782

1700

Digital

Single Phase

1

Single Cylinder, 4-Stroke OHV Air Cooled

80 cc

Breakless Ignition Type, Flywheel Magneto

Unleaded Automotive Gasoline

Recoil

0.9 Gallon

12.9 oz(0.38L)

Counter Clockwise (Facing P.T.O.)

Float

Polyurethane Type

YES

2100

FIRMAN

Rated Fequency 60Hz

Oil Type

See “Add Engine Oil” Section

Magneto Inductor

THD <3%

Grounding System

Floating Neutral

Add Engine Oil

Page 10

DO NOT attempt to crank or start the engine

before it has been properly filled with the

recommended type and amount of oil. Damage

to the generator as a result of failure to follow

these instructions will void your warranty.

1.Place generator on a flat and level surface.

2.Loosen the cover screw and remove the

maintenance cover.

NOTE:

The recommended oil type is 10W-30 automotive

oil. However outdoor temperatures will determine

the space proper oil viscosity for the engine. Use the

chart to select the best for the outdoor temperature

range expected.

The engine is equipped with a low oil shut-off and

will stop when the oil level in the crankcase falls

below the threshold level.

NOTE:

We consider the first 5 hours of run time to be

the break-in period for the unit. During the break

in period stay at or below 50% of the running

watt rating and vary the load occasionally to allow

stator windings to heat and cool. Adjusting the

load will also cause engine speed to vary and help

seat piston rings.

The unit is equipped with a low oil shutdown.If

the oil level becomes lower than required,the

sensor will activate a warning device or stop the

engine.

If generator shuts off and the oil level is within

specifications, check to see if generator is sitting

at an angle that forces oil to shift. Place on an

even surface to correct this. If engine fails to

start, the oil level may not be sufficient to

deactivate low oil level switch. Make sure the

sump is completely full of oil.

5.Replace oil fill cap/dipstick and fully tighten.

6.Reinstall maintenance cover and tighten screws.

4.Using oil funnel, slowly pour contents of

provided oil bottle into oil fill opening to the

"H" mark on dipstick. Be careful do not

overfill. Overfilling with oil could cause the

engine to not start or hard starting.

Low oil shutdown

Degrees Celsiusº(Outside)

Full Synthetic 5W-30

Degrees Fahrenheitº(Outside)

5W-30 10W-40

10W-30

English Customer Service: 1-844-FIRMAN1

3.Remove oil fill cap/dipstick .

7.Oil Level should be checked prior to each use or

at least 8 hours or operation. Keep oil level maintained.

HIGH

H

L

NOTICE:

Page 11

English Customer Service: 1-844-FIRMAN1

The generator neutral is floating, which means

that the AC stator winding is isolated from the

grounding fastener and the AC receptacle

ground pins. On a floating neutral generator

the AC receptacle ground pins are not functional.

Electrical devices, such as a ground fault circuit

interrupter (GFCI), requiring a functioning AC

receptacle ground pin will not operate.

Add Fuel

Fuel must meet these requirements:

•Clean, fresh, unleaded gasoline.

Use regular UNLEADED gasoline with the

generator engine with a minimum 87 octane

/ 87 AKI (91 RON).

For high altitude use, see "Operation at High

Altitude".

Do not use gasoline with more than 10%

alcohol such as E85 or ethanol.

•

Failure to follow Operator's Manual for fuel

recommendations voids warranty.

Avoid generator damage.

DO NOT use unapproved gasoline such as E85.

DO NOT mix oil in gasoline.

DO NOT modify engine to run on alternate fuels.

•

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire or

explosion resulting in death, serious injury.

WHEN ADDING FUEL

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel

expansion. If the tank is overfilled, fuel

can overflow onto a hot engine and cause fire

or explosion. Wipe up any spilled fuel

immediately.

If fuel spills, wait until it evaporates before

starting engine.

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke when

filling the fuel tank.

•

1.Clean area around fuel fill cap, remove cap.

2.Slowly add unleaded fuel to fuel tank. Be

careful not to fill above the red fuel level

indicator . This allows adequate space for

fuel expansion.

3.Install fuel cap and let any spilled fuel

evaporate before starting engine or wipe up

any spilled gasoline.

Grounding

CAUTION

Slowly add unleaded gasoline to fuel tank.

Do not overfill tank.

Do not fill above the red line indicator.

This will allow expansion in hot weather

and prevent overflow.

•

Red Line Indicator

Page 12

English Customer Service: 1-844-FIRMAN1

DO NOT touch bare wires or receptacles.

DO NOT use generator with electrical cords

which are worn,frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or wet

weather.

DO NOT handle generator or electrical cords

while standing in water, while barefoot, or

while hands or feet are wet.

DO NOT allow unqualified persons or children

to operate or service generator.

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

OPERATION

Generator Location

Make sure you review each warning in order to

prevent fire hazard.

Keep area clear of inflammables or other

hazardous materials.

Select a site that is dry, well ventilated and

protected from the weather.

Keep exhaust pipe clear of foreign objects.

Keep generator away from open flame.

Keep generator on a stable and level surface.

WARNING

DANGER

POISONOUS GAS HAZARD.

Engine exhaust contains carbon

monoxide, a poisonous gas that

could kill you in minutes. You

CANNOT smell it, see it, or taste

it. Even if you do not smell exhaust

fumes, you could still be exposed

to carbon monoxide gas.

Avoid other generator hazards.

READ MANUAL BEFORE USE.

Do not block generator air vents with paper or

other material.

CAUTION

Tilting can cause fuel spillage.

Page 13

Surge Protection

Voltage fluctuation may impair the proper

functioning of sensitive electronic equipment.

Electronic devices, including computers and

many programmable appliances use components

that are designed to operate within a narrow

voltage range and may be affected by momentary

voltage fluctuations. While there is no way to

prevent voltage fluctuations, you can take steps

to protect sensitive electronic equipment.

Install UL1449, CSA-listed, plug-in surge

suppressors on the outlets feeding your

sensitive equipment. Surge suppressors come

in single- or multi-outlet styles. They’re

de si g n e d to pr o t e c t a g a i n s t v i r t u a l l y

all short-duration voltage fluctuations.

Operate this product ONLY outside far away

from windows, doors and vents to reduce

the risk of carbon monoxide gas from

accumulating and potentially being drawn

towards occupied spaces.

•

•Install battery-operated carbon monoxide

alarms or plug-in carbon monoxide alarms

with battery back-up according to the

manufacturer’s instructions. Smoke alarms

cannot detect carbon monoxide gas.

•

DO NOT run this product inside homes,

garages, basements, crawlspaces, sheds, or

other partially-enclosed spaces even if using

fans or opening doors and windows for

ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for

hours, even after this product has shut off.

•ALWAYS place this product downwind and

point the engine exhaust away from

occupied spaces. If you start to feel sick,

dizzy, or weak while using this product, shut

it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide

poisoning.

English Customer Service: 1-844-FIRMAN1

Starting the Generator

1. Before starting the generator, check for loose

or missing parts and for any damage which

may have occurred during shipment.

2. Check oil level and fuel.

3. Disconnect all electrical loads from the

generator. Never start or stop the generator

with electrical devices plugged in or turned

on.

4. Turn the fuel cap vent lever to the “O”(l) position.N

5. Turn the fuel valve to the “ON”(l) position.

NOTICE:

Page 14

If engine starts after 3 pulls but fails to run, or if

unit shuts down during operation, make sure

unit is on a level surface and check for proper

oil level in crankcase. This unit may be equipped

with a low oil protection device. If so, oil must

be at proper level for engine to start.

Keep choke lever in “START” position for only 1

pull of the recoil starter. After first pull, move

choke lever to the “RUN” position for up to the

next 3 pulls of the recoil starter. Too much

choke leads to sparkplug fouling/engine

flooding due to the lack of incoming air. This

will cause the engine not to start.

9. Do not over-choke. As soon as engine starts

and warm up, push the choke lever in to the

“RUN” position.

10. Allow generator to run at no load for few

minutes upon each initial start-up to permit

engine and generator to stablize.

Starter cord kickback(rapid

retraction) will pull hand and arm

toward engine faster than you can

let go which could cause broken

WARNING

When starting engine, pull cord slowly until

resistance is felt and then pull rapidly to avoid

kickback.

8. Pull the starter cord slowly until resistance is

felt and then pull rapidly.

English Customer Service: 1-844-FIRMAN1

6. Pull the choke lever out to the “START” position.

7. Flip the engine switch to the “ON”(l) position.

bones, fractures, bruises, or sprains resulting in

serious injury.

Connecting Electrical Loads

1.Let engine stabilize and warm up for a few

minutes after starting.

2.Ensure circuit breaker on control panel is in

on position.

This unit has been pretested and adjusted to

handle its full capacity. Before starting the

generator, disconnect all load. Apply load only

after generator is running. Voltage is regulated

via the engine speed adjusted at the factory for

correct output. Readjusting will void warranty.

When applying a load, do not exceed the maximum

wattage rating of the generator when using one or

more receptacles. Also, do not exceed the amperage

rating of any one receptacle.

Do not apply heavy electrical load during break-in

period (the first five hours of operations).

3.Plug in and turn on the desired 120 Volt AC,

single phase, 60Hz electrical loads. It is

better to attach the item with largest load first.

NOTICE:

Page 15

English Customer Service: 1-844-FIRMAN1

Economy Control Switch

The Economy Control switch can be activated in

order to minimize fuel consumption and noise

while operating the unit during times of reduced

electrical output, allowing the engine speed to

idle during periods of non-use. The engine speed

returns to normal when an electrical load is

connected. When the economy switch is off, the

engine runs at normal speed continuously.

For periods of high electrical load or momentary

fluctuations, the Economy Control Switch should

be turned OFF.

12V DC Outlet (Battery Charger)

The 12V DC outlet is ONLY to be used with the

supplied 12V battery charging cable. The DC

output is unregulated and will damage other

12V DC products.

CAUTION

1. Before connecting the battery charging cable

to a battery that is installed in a vehicle, disconnect

the vehicle battery ground cable from the

negative (–) battery terminal.

Storage batteries give off EXPLOSIVE hydrogen

gas while charging. Do not allow smoking, open

flames, sparks, or spark producing equipment

in the area while charging.

WARNING

Battery electrolyte fluid is comprised of sulfuric

acid that can be very dangerous and cause severe

burns. Do not allow this fluid to contact eyes, skin,

clothing, etc. If contact or spillage does occur,

flush the area with water immediately.

WARNING

Do not continue to charge a battery that becomes

hot or is fully charged.

The amount of current flowing will depend on the

charging voltage and battery's state of charge. As

the battery becomes more fully charged, the output

current to the battery decreases and nearly becomes

constant. Taper chargers are intended to be used

with the provision that they will be disconnected

from the battery after a maximum time on charge.

Normally a period of 30 to 120 minutes is sufficient

to recharge a weak battery. The charge level of the

battery should be checked periodically.

Do not start the vehicle while the battery charging

Cable is connected and the generator is running.

It will not give the battery a boost of power. The

Vehicle or the generator may be damaged. Charge

only vented wet lead acid batteries. Other types

of batteries may burst, causing personal injury

or damage.

NOTICE:

Page 16

English Customer Service: 1-844-FIRMAN1

A DC circuit protector has been provided to

protect the circuit from overloads. If an overload

occurs, the circuit protector will trip. The circuit

protector may be reset by pushing the button of

the protector.

DC CIRCUIT PROTECTOR

Charging a large capacity battery or a totally

discharged battery may cause the DC breaker to

turn off. In these cases, a separate battery charger

unit connected to an AC power source is

recommended instead of the DC receptacle on

the generator.

2. Plug the battery charging cable into the DC

receptacle of the generator.

3. Connect the red (+) battery charger lead to the

red (+) battery terminal.

4. Connect the black (–) battery charger lead to

the black (–) battery terminal.

5. Start the generator.

NOTE:

When the battery circuit is in use the AC capacity

is reduced by 60 watts. Make sure the combined

load is within the rated limits.

WARNING

Do not continue to charge a battery that becomes

hot or is fully charged.

Stopping the Engine

1. Turn off and remove entire electrical loads.

Never start or stop the generator with

electrical devices plugged in or turned on.

Let the generator run at no-load for two

minutes to stabilize internal temperatures

of the engine and generator.

2. Press the engine switch to the “OFF”(O) position.

WARNING

If a cover is used, do not install until unit has cooled.

Fuel and its vapors are extremely flammable and

explosive which could cause burns, fire or

explosion resulting in death, serious injury.

3. Turn the fuel valve to the “OFF”(O) position.

Do not leave the generator until it has

completely stopped.

4. Turn the fuel cap vent lever to the “O”(O) position.FF

DO NOT stop engine by moving choke control

to “START” position.

Important: Always ensure that the Fuel Valve

and the Engine Switch are in the “OFF” position

when the engine is not in use.

If the engine will not be used for a period of two

weeks or longer, please see the Storage section

for proper engine and fuel storage.

Page 17

English Customer Service: 1-844-FIRMAN1

Low Oil Shutdown

If the engine oil drops below a preset level, an

oil switch will stop the engine. Check oil level

with dipstick.

If oil level is between the LOW and HIGH mark on

dipstick:

1.Add oil to bring level to HIGH mark.

2.Restart engine and if the engine stops again

a low oil condition may still exist. DO NOT try

to restart the engine.

3.Contact an Authorized FIRMAN Service Dealer.

4.DO NOT operate engine until oil level is

corrected.

Do Not Overload Generator

Overloading a generator in excess of its rated

wattage capacity can result in damage to the

generator and to connected electrical devices.

To prolong the life of your generator and

attached devices, follow these steps to add

electrical load:

1. Start the generator with no electrical load

attached.

2. Allow the engine to run for several minutes

to stabilize.

3. Plug in and turn on the first item. It is best to

attach the item with the largest load first.

4. Allow the engine to stabilize.

5. Plug in and turn on the next item.

6. Allow the engine to stabilize.

7. Repeat steps 5-6 for each additional item.

Overload Operation

The overload indicator light will turn on when

the load exceeds 1764W(approximately). If the

load exceeds 1860W(approximately), the light

will blink and cut power to the receptacles in 30

seconds.

Parallel Operation

Two FIRMAN model W01782 generators can be

operated in parallel to increase the total available

electrical power to 3100 watts. A FIRMAN parallel

kit (optional equipment) is required for parallel

operation. For kit availability, call Customer Service

at 1-844-347-6261 or visit:www.firmangenerators.com.

1.DO NOT try to restart the engine.

2.Contact an Authorized FIRMAN Service Dealer.

3.DO NOT operate engine until oil level is corrected.

If oil level is below the LOW mark on dipstick:

1. Disconnect any electronic devices, and then

stop the engine.

2. Reduce the total wattage of connected

electronic devices until it is within the generator’s

rated output.

3. Inspect the Air Inlet and Control Panel for any

blockage. Remove blockage if found.

4. Restart Engine.

How to Correct

Page 18

English Customer Service: 1-844-FIRMAN1

MAINTENANCE AND STORAGE

MAINTENANCE SCHEDULE

General Recommendations

Regular maintenance will improve the performance and extend the life of the generator. See any

authorized dealer for service.

The generator's warranty does not cover items that have been subjected to operator abuse or

negligence. To receive full value from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your generator.

All service and adjustments should be made at least once each season. Follow the requirements

in the Maintenanc Shedule chart above.

Notice Once a year you should clean or replace the spark plug and replace the air filter. New

spark plugs and clean air filter assure proper fuel-air mixture and help your engine run better

and last longer.

ITEM NOTES Daily(Before

operation)

Initial

25 hours

Every

50 hours

Every

100 hours

(or annual)

Fittings/

Fasteners

Spark Plug

Engine Oil

Air Filter

Fuel Line

Exhaust

System

Engine

Check condition. Adjust gap

and clean. Replace if necessary.

Check oil level.

Clean, replace if necessary.

Check for leakage. Retighten or

replace gasket if necessary.

Check adjust valve clearance.

Clean combustion chamber.

Check. Replace if necessary.

Check fuel hose for cracks or other

damage. Replace if necessary.

√

Replace.

Check spark arrester screen.

Clean/Replace if necessary.

Every

250 hours

√

To be performed by knowledgable/experienced owner or by authorized service center.

*

Fuel Filter Clean fuel filter and fuel tank

strainer. Replace if necessary. √

La page charge ...

Firman W01782 Manuel utilisateur

Firman W01782 Manuel utilisateur

dans d''autres langues

Documents connexes