JennAir JF36NXFXDE Le manuel du propriétaire

Marque: JennAir

Modèle: JF36NXFXDE

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

JF42NXFXDE

W11310951A

Table of Contents/Table des matières/Índice..........................................................................2

USE AND CARE GUIDE

For questions about features, operation/performance, parts, accessories, or service,

call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.

Get the app, connect instructions, terms of use, and privacy policy at www.jennair.com/connect.

JENNAIR

FRENCH DOOR

REFRIGERATOR

RÉFRIGÉRATEUR JENNAIR

AVEC

PORTEÀDOUBLE BATTANT

REFRIGERADOR DE PUERTAS

FRANCESASJENNAIR

GUIDE D’UTILISATION ET D’ENTRETIEN

Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, accessoires ou service,

composer le 1800JENNAIR (1800536-6247) ou visiter le www.jennair.com.

Au Canada, composer le 1800JENNAIR (1800536-6247) ou visiter le www.jennair.ca.

Obtenez l’application et les instructions de connexion, les conditions d’utilisation

et la politique de condentialité au www.jennair.com/connect.

MANUAL DE USO Y CUIDADO

Si tiene preguntas respecto a las características, funcionamiento/rendimiento, piezas, accesorios o servicio,

llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio web www.jennair.com.

En Canadá, llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio web en www.jennair.ca.

Obtenga la aplicación, las instrucciones de conexión, los términos de uso y la política de privacidad en www.jennair.com/connect.

TABLE OF CONTENTS

TABLE DES MATIÈRES

REFRIGERATOR SAFETY ..............................................................3

Proper Disposal of Your Old Refrigerator ....................................4

BEFORE USE ..................................................................................4

Water Supply Requirements ........................................................4

Water System Preparation ...........................................................5

Install Air Filter

(on some models) ......................................................................... 5

Install Produce Preserver

(on some models) ......................................................................... 5

REFRIGERATOR USE ....................................................................6

Power On/Off Switch ...................................................................6

Using the Controls .......................................................................7

Ice Maker and Storage Bin ..........................................................8

Water Filtration System ................................................................8

REFRIGERATOR FEATURES ......................................................10

Refrigerator Shelves ...................................................................10

Deli/Crisper Drawers ..................................................................10

Wine Rack ..................................................................................10

FREEZER FEATURES ..................................................................10

Freezer Drawer and Pull-out Ice Bin ..........................................10

DOOR FEATURES ........................................................................11

Utility Compartment

(on some models) .......................................................................11

Door Bins ....................................................................................11

REFRIGERATOR CARE ...............................................................11

Cleaning .....................................................................................11

Lights ..........................................................................................12

Power Interruptions ....................................................................12

Vacation Care .............................................................................12

TROUBLESHOOTING ..................................................................13

Refrigerator Operation ...............................................................13

Temperature and Moisture .........................................................14

Ice and Water .............................................................................14

ASSISTANCE OR SERVICE .........................................................15

In the U.S.A. ...............................................................................15

In Canada ...................................................................................15

ACCESSORIES .............................................................................15

PERFORMANCE DATA SHEETS ................................................. 16

WARRANTY ..................................................................................18

SÉCURITÉ DU RÉFRIGÉRATEUR...............................................19

Mise au rebut du vieux réfrigérateur ..........................................20

AVANT UTILISATION ....................................................................20

Spécications de l’alimentation en eau .....................................20

Préparation du circuit d’eau ....................................................... 21

Installer le ltre à air (sur certains modèles) ...............................21

Installer le conservateur de produits frais

(sur certains modèles) ................................................................21

UTILISATION DU RÉFRIGÉRATEUR ..........................................22

Interrupteur d’alimentation On/Off (marche/arrêt) .....................22

Utilisation des commandes .......................................................23

Machine à glaçons et bacd’entreposage .................................25

Système de ltration d’eau ........................................................25

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................26

Tablettes du réfrigérateur ...........................................................26

Bacs pour spécialités alimentaires/àlégumes ..........................27

Casier à vin .................................................................................27

CARACTÉRISTIQUES DU CONGÉLATEUR ...............................27

Tiroir de congélateur et bac àglaçonscoulissant .....................27

CARACTÉRISTIQUES DE LA PORTE .........................................27

Compartiment utilitaire (sur certains modèles) ..........................27

Balconnets de porte ...................................................................27

ENTRETIEN DU RÉFRIGÉRATEUR ............................................28

Nettoyage ...................................................................................28

Lampes .......................................................................................28

Pannes de courant .....................................................................28

Entretien avant les vacances .....................................................29

DÉPANNAGE .................................................................................29

Fonctionnement du réfrigérateur ...............................................29

Température et humidité ............................................................30

Glaçons et eau ...........................................................................31

ASSISTANCE OU SERVICE .........................................................32

Aux É.-U. ....................................................................................32

Au Canada ..................................................................................32

ACCESSOIRES .............................................................................32

FEUILLES DE DONNÉES SUR LA PERFORMANCE ................33

GARANTIE .....................................................................................35

ÍNDICE

SEGURIDAD DEL REFRIGERADOR ...........................................37

Cómo deshacerse adecuadamente desu refrigerador viejo ....38

ANTES DEL USO ..........................................................................38

Requisitos del suministro de agua .............................................38

Preparación del sistema de agua ..............................................39

Instalar el ltro de aire

(en algunos modelos) .................................................................39

Cómo instalar el preservador dealimentos frescos

(en algunos modelos) .................................................................39

USO DE SU REFRIGERADOR .....................................................40

Interruptor de On/Off

(Encendido/Apagado) ................................................................40

Uso de los controles ..................................................................41

Fábrica de hielo y depósito dealmacenamiento .......................42

Sistema de ltración de agua ....................................................43

CARACTERÍSTICAS DEL REFRIGERADOR .............................44

Estantes del refrigerador ............................................................44

Cajones para carnes frías/verduras ...........................................44

Portabotellas ..............................................................................45

CARACTERÍSTICAS DEL CONGELADOR .................................45

Cajón del congelador y depósito removible de hielo ................45

CARACTERÍSTICAS DE LA PUERTA .........................................45

Compartimiento de uso general

(en algunos modelos) .................................................................45

Recipientes de la puerta ............................................................45

CUIDADO DEL REFRIGERADOR ...............................................46

Limpieza .....................................................................................46

Luces ..........................................................................................46

Cortes de corriente ....................................................................46

Cuidados en período de vacaciones .........................................46

SOLUCIÓN DE PROBLEMAS......................................................47

Funcionamiento del refrigerador ................................................47

Temperatura y humedad ............................................................48

Hielo y agua ................................................................................49

ASISTENCIA O SERVICIO TÉCNICO .........................................50

En los EE.UU. .............................................................................50

En Canadá ..................................................................................50

ACCESORIOS ...............................................................................50

HOJAS DE DATOS DE RENDIMIENTO ......................................51

GARANTÍA ....................................................................................53

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded (earthed) outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■

Do not store or use petrol, flammable liquids or gas in the

vicinity of this or other electrical appliances. The fumes can

cause fires or explosions.

■ Do not store explosive substances such as aerosol cans

with a flammable propellant in this refrigerator.

■ Do not use or place electrical devices inside the refrigerator

compartments if they are not of the type expressly

authorized by the manufacture.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ A qualified service technician must install the water line and

ice maker. See installation instruction supplied with

ice maker kit IC13B for complete details.

■

Connect to a potable water supply only.

■ Use a sturdy glass when dispensing ice (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

■ To avoid the risk of children becoming trapped and

suffocating, do not allow them to play or hide inside the

refrigerator.

■ If the power supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly qualified

person.

Proper Disposal of Your Old

Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

–even if they will sit for “just a few days.” If you are getting rid

of your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

BEFORE USE

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your ngers. Wipe with warm water

and dry.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see “Refrigerator Safety.”

■ Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions in

“Refrigerator Care.”

Water Supply Requirements

Read all directions before you begin.

IMPORTANT:

■ When your refrigerator was installed, the water connection

from the water source should have been connected to your

refrigerator. If your refrigerator is not connected to a water

source, see “Connect to Water Line” in the Installation

Instructions. If you have any questions about your water

connection, see “Troubleshooting” or call a licensed, qualied

plumber.

■ If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF. See “Ice Maker and

Storage Bin.”

■ All installations must meet local plumbing code requirements.

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the oor with

cardboard or hardboard to avoid oor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as oor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker.

NOTE: If the water pressure is less than what is required, the ow

of water from the water dispenser could decrease or ice cubes

could be hollow or irregular shaped. If you have questions about

your water pressure, call a licensed, qualied plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of

a reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water ltration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 psi (276 kPa).

If the water pressure to the reverse osmosis system is less than

40 psi (276 kPa):

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy usage.

■ If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water lter. See “Water Filtration

System.”

If you have questions about your water pressure, call a licensed,

qualied plumber.

Water System Preparation

Please read before using the water system.

IMPORTANT:

■ After connecting the refrigerator to a water source or after

replacing the water lter, ll and discard two full containers of

ice to prepare the water lter for use before using the ice.

■ Connect to potable water supply only.

1. To turn on the ice maker, simply lower the wire shutoff arm.

See “Ice Maker and Storage Bin” for further instructions on

the operation of your ice maker.

NOTE: Allow 24 hours to produce the rst batch of ice.

NOTE: If your model has a base grille lter system, make sure

the base grille lter is installed so that the Eject button is out. See

“Water Filtration System.”

Install Air Filter

(on some models)

An air lter is 15 times more powerful than baking soda at

reducing common food odors inside the refrigerator.

On some models, your refrigerator’s accessory packet includes

an air lter which must be installed prior to use.

Installing the Air Filter

Install the air lter in the ceiling, along the back wall, of the

refrigerator compartment.

1. Remove the air lter from its packaging.

2. Snap the lter into place.

Replacing the Air Filter

The disposable air lter should be replaced every 6 months. To

order a replacement air lter, contact us. See “Accessories” for

information on ordering.

1. Remove the used air lter by squeezing in on the side tabs.

2. Install the new air lter by snapping it into place.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies, depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate-to-high amounts of ethylene.

Sensitivity

to Ethylene

Ethylene

Production

Apples High Very High

Asparagus Medium Very Low

Berries Low Low

Broccoli High Very Low

Cantaloupe Medium High

Carrots Low Very Low

Citrus Fruit Medium Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Installing the Produce Preserver

1. Wash the interior of a drawer with a solution of mild dish soap

and warm water and dry thoroughly.

2. Find the package containing the Produce Preserver inside the

refrigerator and install the Produce Preserver into the drawer

according to the instructions provided in the package.

Replacing the Produce Preserver

The disposable packets should be replaced every 6 months or

when the status indicator changes completely from white to red.

To order replacements, contact us. See “Accessories” section for

information on ordering.

1. Remove the used packets from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement packets and status indicator using the

instructions included in the package.

REFRIGERATOR USE

Power On/Off Switch

If you need to turn the power to your refrigerator On or Off, you

must remove the top grille assembly to access the power switch.

Turn the power to the refrigerator Off before plugging/unplugging

unit, or when cleaning your refrigerator.

To Remove Top Grille:

1. Grasp both ends of the top grille.

2. Pull the bottom out. Then, push the top grille straight up and

pull it straight out. Place the grille on a soft surface.

To Replace Top Grille:

1. Insert top grille hooks (located on the back of the top grille)

onto mounting bolts on the side trim.

2. Pull the grille down slightly and push the bottom in to lock it

into place.

Turn Power On or Off:

1. Remove top grille.

2. Press power switch to the On or Off position.

3. Replace top grille.

IMPORTANT: Be sure the power switch is set to the On position

after cleaning refrigerator.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

B BA

A. Power switch

A. Top grille

B. Cabinet side trims

Using the Controls

IMPORTANT:

■ The Fridge control adjusts the temperature in the refrigerator

compartment. The Freezer control adjusts the temperature in

the freezer compartment.

■ Wait 24 hours after you turn on the refrigerator before you put

food into it. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the temperature controls to a lower (colder)

setting will not cool the compartments any faster.

■ If the temperature is too warm or too cold in the refrigerator

or freezer, rst check the air vents to be sure they are not

blocked before adjusting the controls.

■ The recommended settings should be correct for normal

household usage. The controls are set correctly when milk or

juice is as cold as you like and when ice cream is rm.

■ The actual temperature may differ from the display when a

door is open for an extended period of time.

Turning On Cooling and Viewing Set Points

The factory recommended set points are 0°F (-18°C) for the

freezer and 37°F (3°C) for the refrigerator

1. Press the FRIDGE or FREEZER touch pad.

NOTE: After the refrigerator is turned on, the Over

Temperature audio alarm and indicator light may activate

every 1½ hours until the refrigerator and freezer temperatures

are below 48°F (9°C) and 15°F (-9°C), respectively, or until the

alarm is turned off. To turn off the audio alarm and indicator

light, see “Alarm Reset.”

Turning Off Cooling

1. Press the FRIDGE or FREEZER touch pad.

2. Press and hold the COOLING OFF touch pad for 3 seconds.

NOTE: To turn off the power completely, use the power

ON/ OFF switch located behind the top grille. See “Power On/

Off Switch.”

Viewing the Temperature in Degrees Celsius

1. Press °C touch pad. To display degrees Fahrenheit, press °F

touch pad.

NOTE: If the freezer temperature is below zero, the negative

sign next to the freezer display will light up. This is normal.

Adjusting Controls

NOTE: Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

To Adjust Set Point Temperatures:

■ Press the FRIDGE or FREEZER touch pad, and then press the

Plus (+) or Minus (-) touch pad until the desired temperature is

reached.

■ Press the SAVE touch pad to program the desired

temperature.

NOTE: The set point range for the freezer is -5°F to 3°F (-21°C

to -16°C). The set point range for the refrigerator is 34°F to 42°F

(1°C to 6°C).

CONDITION /REASON:: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold

Not set correctly for conditions

REFRIGERATOR Control 1°

higher

REFRIGERATOR too warm

High use or room very warm

REFRIGERATOR Control 1°

lower

FREEZER too cold

Not set correctly for conditions

FREEZER Control1° higher

FREEZER too warm/too little

ice

High use or heavy ice use

FREEZER Control 1° lower

Options

Max Ice

The Max Ice feature speeds up the ice production rate to assist

with periods of heavy ice usage.

■ Press OPTIONS, and then press MAX ICE to turn on the Max

Ice feature. Max Ice will remain activated for 24 hours unless

manually turned off.

NOTE: The temperature display for the refrigerator and freezer

compartments will remain at the user’s set points, but the actual

temperature of the freezer compartment will drop to -5°F (-21°C),

while the Max Ice feature is enabled. After 24 hours, the freezer

will return to the previous temperature set point.

Max Cool

The Max Cool feature assists with full grocery loads, temporarily

warm room temperatures, or during heavy door opening use.

■ Press OPTIONS, and then press MAX COOL to turn on the

Max Cool feature. Max Cool will remain activated for 24 hours

unless manually turned off.

NOTE: The temperature display for the refrigerator compartment

will remain at the user’s set point, but the actual temperature

of the refrigerator compartment will drop to 34°F (1°C), while

the Max Cool feature is enabled. After 24 hours, the refrigerator

returns to the previous temperature set points.

Sabbath Mode

Sabbath mode is designed for the traveler or for those whose

religious observances require turning off the lights and ice maker.

By selecting this feature, the temperature set points remain

unchanged, the ice maker will be disabled, the interior lights

will turn off, and the audio tones are muted. For most efcient

refrigerator operation, it is recommended to exit Sabbath mode

when it is no longer required.

■ Press the SABBATH touch pad to turn on Sabbath mode. This

feature will remain on until Sabbath is pressed again.

NOTE: If the Max Cool or Max Ice feature has been selected

prior to turning on Sabbath mode, Max Cool and Max Ice will be

automatically canceled upon entering Sabbath mode.

Filter Reset

See “Water Filter Indicator” in the “Water Filtration System”

section.

Alarm Functions

Alarm Reset

Pressing any Home Screen touch pad (Fridge, Freezer or Options)

will turn off the audio alarm and indicator light. The audio alarm

will not sound again for the current condition that caused the

alarm until a new condition occurs.

An Alarm Reset can be performed by pressing any Home Screen

touch pad (Fridge, Freezer or Options), or by turning the power

to the refrigerator off and on again. See “Power On/Off Switch.”

After performing an Alarm Reset, the indicator light will reactivate

if the condition that caused the alarm is still present. See “Door

Open,” “Over Temperature” or “Power Outage.”

Door Open

An alarm will sound when a door has been open for longer than

5 minutes. Closing the door or drawer, or pressing any Home

Screen touch pad (Fridge, Freezer or Options) will reset the Door

Open feature and turn off the audio alarm.

NOTE: If the door(s) or drawer are left open for 10 minutes the

interior lights will go out. Closing the open door(s) or drawer will

reset the lights.

Over Temperature

IMPORTANT: If the Over Temperature Alarm activates, your food

may spoil. See “Power Interruptions.” Minimize door openings

until temperatures return to normal.

The Over Temperature feature is designed to let you know when

either the refrigerator temperature rises above 48°F (9°C) or

the freezer temperature rises above 15°F (-9°C) for longer than

1½ hours. The audio alarm will shut off automatically when the

temperature returns to normal, but the indicator light will continue

to ash to let you know that an Over Temperature condition

occurred until an Over Temperature reset has been performed.

Press any Home Screen touch pad (Fridge, Freezer or Options) to

turn off the indicator light.

If the over temperature condition is still present when an Over

Temperature reset is performed, the indicator light will continue

to reactivate every 1½ hours until refrigerator and freezer

temperatures are below 48°F (9°C) and 15°F (-9°C), respectively.

Power Outage

When a power outage occurs, a Power Outage indicator light will

be displayed. Press any Home Screen touch pad (Fridge, Freezer

or Options) to turn off the indicator light. The power outage

indicator light will not display when either Cooling Off or Sabbath

mode is active, but will appear after exiting Sabbath mode if a

power outage occurred.

Ice Maker and Storage Bin

IMPORTANT: After connecting the refrigerator to a water source

or replacing the water lter, ll and discard two full containers of

ice to prepare the water lter for use, before using the ice.

Turn the Ice Maker On/Off

1. To turn ON the ice maker, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will ll the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position. Do not force the wire shutoff arm up or down.

2. To manually turn off the ice maker, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click.

Ice Storage Bin Care

NOTE: It is normal for ice to stick together in the ice bin. It

is recommended that the ice bin be emptied and cleaned as

needed.

To clean the ice storage bin:

1. Slide the ice bin out of the freezer, and then lift up and out.

2. Empty the ice bin. Use warm water to melt the ice if

necessary.

NOTE: Do not use anything sharp to break up the ice in the

bin. This can cause damage to the ice bin and the dispenser

mechanism.

3. Wash ice bin with warm water and a mild detergent, rinse well

and dry thoroughly. Do not use harsh or abrasive cleaners or

solvents.

REMEMBER:

■ Allow 24 hours to produce the rst batch of ice.

■ It may take 3 to 4 days for the ice bin to completely ll, if no

ice is used.

■ The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

■ Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

■ It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

■ Do not store anything inside the ice bin.

Water Filtration System

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Indicator (on some models)

The water lter indicator, located on the control panel, will help

you know when to change the water lter.

A replacement water lter should be ordered when “Order Filter”

is displayed. It is recommended that you replace the lter when

“Replace Filter” is displayed or when water ow to your water

dispenser and/or ice maker decreases noticeably. See “Changing

the Water Filter” later in this section.

After changing the water lter, press and hold FILTER RESET for

3 seconds until the “Order Filter” or “Replace Filter” indicator light

disappears.

Changing the Water Filter

The water lter is located in the base grille below the freezer

compartment door. It is not necessary to remove the base grille to

remove the lter.

1. Remove the lter by pressing the eject button and pulling

straight out on the lter cap.

NOTES:

■ Avoid twisting the cap when removing the lter because

this could cause the cap to come off. If this occurs,

replace the cap and pull the lter straight out.

■ There will be water in the lter. Some spilling may occur.

2. Remove the cap by turning it counterclockwise until it stops.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement lter.

3. Align the ridge on the cap with the arrow on the new lter, and

then turn the cap until it snaps into place.

4. Remove the covers from the O-rings. Be sure the O-rings are

still in place after the covers are removed.

5. Place the cap (removed in Step 2) on the new lter. Align the

ridge on the cap with the arrow on the lter. Turn the cap

clockwise until it snaps into place.

6. Push the new lter into the opening in the base grille. As the

lter is inserted, the eject button will depress. The eject button

will pop back out when the lter is fully engaged.

7. Pull gently on the cap to check that the lter is securely in

place.

8. Flush the water system. Depending on your model, see

“Water and Ice Dispensers” or “Ice Maker and Storage Bin.”

Using the Ice Maker Without a Water Filter

You can operate the ice maker without a water lter. Your ice will

not be ltered.

1. Remove the lter by pressing the eject button and pulling on

the cap. See “Changing the Water Filter” earlier in this section.

2. Remove the cap by turning it counterclockwise until it stops.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator.

3. With the cap in a horizontal position, insert the cap into the

base grille until it stops.

4. Turn the cap counterclockwise until the cap slips into the

attachment slot. Then, turn the cap clockwise until it is in a

horizontal position.

NOTE: The cap will not be even with the base grille.

A. Eject button

B. Filter cap

A. Cover

B. O-rings

A. Eject button

B. Arrow on lter

C. Ridge on cap

REFRIGERATOR FEATURES

Refrigerator Shelves

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to t different heights of items will make

nding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open, and save energy.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf by tilting it up at the front and lifting it out of

the shelf supports. Pull shelf straight out.

2. Reposition the shelf supports in the desired location. Check

that they are level and rmly inserted in the support rails.

3. Place the back of the shelf in the shelf supports.

4. Lower the front of the shelf and make sure that it is in

position.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh sh or shellsh......................... use same day as purchased

Chicken, ground beef, variety meats (liver) ...................... 1-2 days

Cold cuts, steaks/roasts .................................................. 3-5 days

Cured meats................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

Deli/Crisper Drawers

To remove and replace the deli/crisper drawers:

1. Slide the deli/crisper drawer straight out to the stop. Lift the

front of the drawer with one hand while supporting the bottom

with the other hand. Slide the drawer out the rest of the way.

2. To replace the deli/crisper drawer, pull out the drawer slides

until they are fully extended and set the drawer on the slides.

Push the drawer in toward the back until it is in closed

position.

3. Reopen the deli/crisper drawer to make sure it has been

replaced properly.

Wine Rack

To remove and replace the wine rack:

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the wall

of the refrigerator.

FREEZER FEATURES

Freezer Drawer and Pull-out Ice Bin

The freezer drawer can be used to store smaller items. The

freezer drawer is not removable.

To remove and replace the ice bin:

1. Slide the ice bin out of the freezer, and then lift up and out.

2. To replace the ice bin, pull out the drawer slides until they are

fully extended, and then set ice bin on the slides. Push the ice

bin in toward the back until it is in closed position.

3. Reopen the ice bin to make sure it has been replaced

properly.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of

food, the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 lbs of food per cubic foot [907-

1,350 g per 28 L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. Be sure to leave

enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

A. Ice bin

B. Freezer drawer

DOOR FEATURES

Utility Compartment

(on some models)

The utility compartment can be placed in any position on the

refrigerator door.

To remove and replace the utility bin:

1. Remove utility compartment by grasping both ends and lifting

compartment up and out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

Door Bins

Large door bins hold gallon containers and the smaller door bins

hold 2-liter bottles. The door bins are adjustable and removable

for easy cleaning and adjusting.

Gallon Door Bin

To install the gallon door bin:

NOTE: The gallon door bin can only be placed on the lower door

support.

1. Position gallon door bin above lowest door adjustment slot.

2. Push down to secure bin.

3. Adjust other bins, as necessary to allow for milk or beverage

container height.

Door Bins

To remove and replace the door bins:

1. Remove the bin by lifting it up and pulling it out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

To Clean Your Refrigerator:

1. Remove the top grille. See “Power On/Off Switch.”

2. Press the power switch to OFF.

3. Remove all removable parts from inside, such as shelves,

crispers, etc.

4. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

■ Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, ammable uids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

■ To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to

1 qt [26 g to 0.95 L] of water).

5. Clean the exterior surfaces.

Stainless steel panels: Wash stainless steel with a clean

sponge or soft cloth and a mild detergent in warm water.

■ To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested

that you use the manufacturer’s approved Stainless Steel

Cleaner and Polish.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to come

into contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth. To

order the cleaner, see “Accessories.”

6. Press the power switch to ON.

7. Replace the top grille. See “Power On/Off Switch.”

WARNING

Explosion Hazard

Use nonammable cleaner.

Failure to do so can result in death, explosion, or re.

Lights

The lights in both the refrigerator and freezer compartments

are LEDs which do not need to be replaced. If the lights do not

illuminate when the door or drawer is opened, call for assistance

or service. In the U.S.A., call 1-800-JENNAIR (1-800-536-6247). In

Canada call 1-800-JENNAIR (1-800-536-6247).

Power Interruptions

If the power will be out for 24 hours or less, keep the door or

doors closed (depending on your model) to help food stay cold

and frozen.

If the power will be out for more than 24 hours, do one of the

following:

■ Remove all frozen food and store it in a frozen food locker.

■ Place 2 lbs (907 g) of dry ice in the freezer for every cubic foot

(28 L) of freezer space. This will keep the food frozen for 2 to

4 days.

■ If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially lled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and avor may be affected. If the

condition of the food is poor, dispose of it.

Vacation Care

Your refrigerator is equipped with the Sabbath mode feature,

which is designed for the traveler or for those whose religious

observances require turning off the lights and ice maker.

By selecting this feature, the temperature set points remain

unchanged, the ice maker will be disabled and the interior

lights will turn off. For most efcient refrigerator operation, it

is recommended to exit Sabbath mode when it is no longer

required.

If You Choose to Leave the Refrigerator On While

You’re Away:

1. Use up any perishables and freeze other items.

2. Press the SABBATH touch pad.

3. If your refrigerator has an automatic ice maker, shut off the

water supply to the ice maker.

4. Empty the ice bin.

5. When you return from vacation, press the SABBATH touch

pad to return to normal operation.

If You Choose to Turn Off the Refrigerator Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day

ahead of time.

■ When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

3. Under the Fridge or Freezer menu, press and hold COOLING

OFF for 3 seconds to turn off cooling.

NOTE: To turn off the power completely, use the power ON/

OFF switch located behind the top grille. See “Power On/Off

Switch.”

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

When you get to your new home, put everything back and refer to

the “Installation Instructions” section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service

call, refer to the warranty page in this manual, visit http://producthelp.jennair.com or call 1-800-JENNAIR (1-800-536-6247). In Canada,

visit www.jennair.ca.

In the U.S.A.:

JennAir Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

In Canada:

JennAir Brand Home Appliances

Customer eXperience Centre

200 – 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Refrigerator Operation

The refrigerator will not operate

■ Power cord unplugged? Plug into a grounded 3 prong outlet.

■ Is outlet working? Plug in a lamp to see if the outlet is

working.

■ Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

■ Are controls on? Make sure the refrigerator controls are on.

See “Using the Control(s).”

■ New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to

its high-efciency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to

this reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below

are listed some normal sounds with explanations.

■ Buzzing - heard when the water valve opens to ll the ice

maker.

■ Pulsating - fans/compressor adjusting to optimize

performance.

■ Hissing/Rattling - ow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator.

■ Sizzling/Gurgling - water dripping on the heater during

defrost cycle.

■ Popping - contraction/expansion of inside walls, especially

during initial cool-down.

■ Water running - may be heard when ice melts during the

defrost cycle and water runs into the drain pan.

■ Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

There is no audible door open alarm

Has the door been open less than 5 minutes? The door open

alarm will only ash when the door has been open for 5 minutes.

The audible alarm will sound the rst time the door is left open

for more than 5 minutes. Subsequent door open alarms will only

ash. You must reset the audible alarm each time. See “Using the

Control(s).”

The doors will not close completely

■ Door blocked open? Move food packages away from door.

■ Bin or shelf in the way? Push bin or shelf back in the correct

position.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

The doors are difﬁcult to open

■ Are the gaskets dirty or sticky? Clean gaskets and contact

surfaces with mild soap and warm water. Rinse and dry with

soft cloth.

The lights do not work

■ Is the refrigerator in Sabbath mode? See “Using the

Controls.”

■ Has the door been open more than 10 minutes? See

“Using the Controls.”

Temperature and Moisture

Temperature is too warm

■ New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

■ Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

■ Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

■ Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in 24

hours. See “Using the Control(s).”

■ Refrigerator not cooling? For models with digital controls,

turn the refrigerator OFF and then ON to reset. If this does not

correct the problem, call for service.

■ Air vents blocked? Remove any item from in front of the air

vents.

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

■ Humid room? Contributes to moisture buildup.

■ Door(s) opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

Ice and Water

The ice maker is not producing ice or not enough ice

■ Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

■ Kink in the water source line? A kink in the line can reduce

water ow. Straighten the water source line.

■ Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

■ New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

■ Freezer door closed completely? Firmly close the freezer

compartment door. If the freezer compartment door will not

close all the way, see “The doors will not close completely,”

earlier in this section.

■ Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

■ Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

■ Water lter installed on the refrigerator? Remove lter and

operate ice maker. If ice volume improves, then the lter may

be clogged or incorrectly installed. Replace lter or reinstall it

correctly.

■ Reverse osmosis water ltration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements.”

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

■ Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

■ Kink in the water source line? A kink in the line can reduce

water ow. Straighten the water source line.

■ Water lter installed on the refrigerator? Remove lter and

operate ice maker. If ice quality improves, then the lter may

be clogged or incorrectly installed. Replace lter or reinstall it

correctly.

■ Reverse osmosis water ltration system connected to

your cold water supply? This can decrease water pressure.

See “Water Supply Requirements.”

■ Questions remain regarding water pressure? Call a

licensed, qualied plumber.

Ice is sticking together in the ice storage bin

■ It is normal for frost to be on top of the ice storage bin due to

normal opening and closing of the freezer.

■ It is normal for ice to stick together when it is not dispensed

or used frequently. It is recommended that the ice storage

bin be emptied and cleaned as needed. See “Ice Maker and

Storage Bin.”

Off-taste, odor or gray color in the ice

■ New plumbing connections? New plumbing connections

can cause discolored or off-avored ice.

■ Ice stored too long? Discard ice. Wash ice bin. Allow 24

hours for ice maker to make new ice.

■ Odor transfer from food? Use airtight, moisture proof

packaging to store food.

■ Are there minerals (such as sulfur) in the water? A water

lter may need to be installed to remove the minerals.

■ Is there a water lter installed on the refrigerator? Gray

or dark discoloration in ice indicates that the water ltration

system needs additional ushing.

WARNING

Explosion Hazard

Use nonammable cleaner.

Failure to do so can result in death, explosion, or re.

ASSISTANCE OR SERVICE

If You Need Service

Please refer to the warranty page in this manual.

If You Need Replacement Parts

If you need to order replacement parts, we recommend that

you use only factory specied parts. Factory specied parts will

t right and work right because they are made with the same

precision used to build every new JennAir

appliance.

To locate factory specied parts in your area, call us or your

nearest designated service center.

In the U.S.A.

Call the JennAir Customer eXperience Center toll free

1-800-JENNAIR (1-800-536-6247), or visit our website at

www.jennair.com.

Our consultants provide assistance with:

■ Features and specications on our full line of appliances.

■ Referrals to local JennAir brand dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

For Further Assistance

If you need further assistance, you can write to JennAir with any

questions or concerns at:

JennAir Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the JennAir Canada LP Customer eXperience Centre toll free

1-800-JENNAIR (1-800-536-6247), or visit our website at

www.jennair.ca.

Our consultants provide assistance with:

■ Scheduling of service. JennAir

appliances designated service

technicians are trained to fulll the product warranty and

provide after-warranty service, anywhere in Canada.

■ Features and specications on our full line of appliances.

■ Referrals to local JennAir brand dealers.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

For Further Assistance

If you need further assistance, you can write to JennAir Canada

LP with any questions or concerns at:

JennAir Brand Home Appliances

Customer eXperience Centre

200 – 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

ACCESSORIES

The following accessories are available for your refrigerator. To

order an accessory, contact us and ask for the part number.

In the U.S.A., visit our website www.jennair.com/accessories or

call 1-800-JENNAIR (1-800-536-6247).

In Canada, visit our webpage www.jennair.ca or call

1-800-JENNAIR (1-800-536-6247).

Affresh

Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

Affresh

Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

Affresh

Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Replacement Water Filter:

In U.S.A., order Part #4396841 (T2RFWG2)

In Canada, order Part #4396841B (T2RFWG2)

Air Filter:

Order Part #W10311524

Produce Preserver Keep Fresh Packet Rell:

Order Part #P1KC6R1

PERFORMANCE DATA SHEETS

Base Grille Water Filtration System

Model T1WG2L/T2RFWG2 Capacity 200 Gallons (757 Liters)

Model T1WG2/T2RFWG2 Capacity 200 Gallons (757 Liters)

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42 and 53.

Substance Reduction

Aesthetic Effects

NSF

Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Chlorine Taste/Odor

Particulate Class II*

50% reduction

85% reduction

2.0182 mg/L

1333333 #/mL

2.0 mg/L ± 10%

At least

10,000 particles/mL

0.06 mg/L

6600 #/mL**

0.0536 mg/L

2325 #/mL

97.03%

99.51%

97.34%

99.83%

Contaminant

Reduction

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Lead: @ pH 6.5 ***

Lead: @ pH 8.5 ***

0.010 mg/L

0.1533 mg/L

0.1400 mg/L

0.15 mg/L ± 10%

0.0005 mg/L

0.0007 mg/L

0.0005 mg/L

0.0006 mg/L

99.67%

99.50%

99.67%

99.57%

Mercury: @ pH 6.5

Mercury: @ pH 8.5

0.002 mg/L

0.0058 mg/L

0.0059 mg/L

0.006 mg/L ± 10%

0.0002 mg/L

0.0005 mg/L

0.0002 mg/L

0.0003 mg/L

96.54%

91.57%

96.54%

94.92%

Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L ± 10% 0.0012 mg/L 0.0006 mg/L 92.22% 96.34%

O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L ± 10% 0.0250 mg/L 0.0066 mg/L 98.58% 99.63%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L ± 10% 0.001 mg/L 0.001 mg/L 93.3% 93.3%

Carbofuran 0.040 mg/L 0.0819 mg/L 0.08 mg/L ± 10% 0.0400 mg/L 0.0213 mg/ 51.13% 74.00%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.85 gpm (3.2 Lpm). Pressure = 60 psig (413.7 kPa).

Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

■ It is essential that operational, maintenance, and lter

replacement requirements be carried out for the product to

perform as advertised.

■ Use replacement lter T2RFWG2, part #4396841.

Model T1WG2L: Style 1 – When the lter indicator reads

10%, order a new lter. When the indicator reads 0%, it is

recommended that you replace the lter.

Style 2 – When the lter indicator changes from green to

yellow, order a new lter. When the indicator changes from

yellow to red, it is recommended that you replace the lter.

Style 3 – When the water lter status display changes from

“GOOD” to “ORDER,” order a new lter. When the lter

indicator reads “REPLACE,” it is recommended that you

replace the lter.

Style 4 – Press FILTER to check the status of your water lter.

If the lter indicator light is yellow, order a new lter. If the lter

indicator light is red, it is recommended that you replace the

lter.

Model T1WG2: Change the water lter cartridge every 6

months. If the water ow to the water dispenser or ice maker

decreases noticeably before 6 months have passed, replace

the water lter cartridge more often.

■ These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory

conditions, actual performance may vary.

■ The product is for cold water use only.

■ Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system.

■ Refer to the “Warranty” section for the Manufacturer’s name,

address and telephone number.

■ Refer to the “Warranty” section for the Manufacturer’s limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

35 - 120 psi (241 - 827 kPa)

33° - 100°F (1° - 38°C)

0.85 gpm (3.2 L/min.) @ 60 psi*

System tested and certied by NSF International against NSF/ANSI Standard 42 for

the reduction of Chlorine Taste and Odor, Particulate Class II*; and against NSF/ANSI

Standard 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene,

and Carbofuran.

*Class II particle size: 1 um to <5 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dus

***Compliant for Lead reduction requirements under NSF/ANSI Standard 53 as tested by Pace Analytical Services, Inc.

NSF is a registered trademark of NSF International.

Base Grille Water Filtration System

Model T1WG2L/T2RFWG2 Capacity 200 Gallons (757 Liters)

Model T1WG2/T2RFWG2 Capacity 200 Gallons (757 Liters)

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42 and 53.

Substance Reduction

Aesthetic Effects

NSF

Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Chlorine Taste/Odor

Particulate Class II*

50% reduction

85% reduction

2.0182 mg/L

1333333 #/mL

2.0 mg/L ± 10%

At least

10,000 particles/mL

0.06 mg/L

6600 #/mL**

0.0536 mg/L

2325 #/mL

97.03%

99.51%

97.34%

99.83%

Contaminant

Reduction

NSF Reduction

Requirements

Average

Inuent

Inuent Challenge

Concentration

Maximum

Efuent

Average

Efuent

Minimum%

Reduction

Average%

Reduction

Lead: @ pH 6.5 ***

Lead: @ pH 8.5 ***

0.010 mg/L

0.1533 mg/L

0.1400 mg/L

0.15 mg/L ± 10%

0.0005 mg/L

0.0007 mg/L

0.0005 mg/L

0.0006 mg/L

99.67%

99.50%

99.67%

99.57%

Mercury: @ pH 6.5

Mercury: @ pH 8.5

0.002 mg/L

0.0058 mg/L

0.0059 mg/L

0.006 mg/L ± 10%

0.0002 mg/L

0.0005 mg/L

0.0002 mg/L

0.0003 mg/L

96.54%

91.57%

96.54%

94.92%

Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L ± 10% 0.0012 mg/L 0.0006 mg/L 92.22% 96.34%

O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L ± 10% 0.0250 mg/L 0.0066 mg/L 98.58% 99.63%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L ± 10% 0.001 mg/L 0.001 mg/L 93.3% 93.3%

Carbofuran 0.040 mg/L 0.0819 mg/L 0.08 mg/L ± 10% 0.0400 mg/L 0.0213 mg/ 51.13% 74.00%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).

Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

■ It is essential that operational, maintenance, and lter

replacement requirements be carried out for the product to

perform as advertised.

■ Use replacement lter T2RFWG2, part #4396841.

Model T1WG2L: Style 1 – When the lter indicator reads

10%, order a new lter. When the indicator reads 0%, it is

recommended that you replace the lter.

Style 2 – When the lter indicator changes from green to

yellow, order a new lter. When the indicator changes from

yellow to red, it is recommended that you replace the lter.

Style 3 – When the water lter status display changes from

“GOOD” to “ORDER,” order a new lter. When the lter

indicator reads “REPLACE,” it is recommended that you

replace the lter.

Style 4 – Press FILTER to check the status of your water lter.

If the lter indicator light is yellow, order a new lter. If the lter

indicator light is red, it is recommended that you replace the

lter.

Model T1WG2: Change the water lter cartridge every 6

months. If the water ow to the water dispenser or ice maker

decreases noticeably before 6 months have passed, replace

the water lter cartridge more often.

■ These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory

conditions, actual performance may vary.

■ The product is for cold water use only.

■ Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system.

■ Refer to the “Warranty” section for the Manufacturer’s name,

address and telephone number.

■ Refer to the “Warranty” section for the Manufacturer’s limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

35 - 120 psi (241 - 827 kPa)

33° - 100°F (1° - 38°C)

0.5 gpm (1.9 L/min.) @ 60 psi*

System tested and certied by NSF International against NSF/ANSI Standard 42 for

the reduction of Chlorine Taste and Odor, Particulate Class II*; and against NSF/ANSI

Standard 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene,

and Carbofuran.

*Class II particle size: 1 um to <5 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dus

***Compliant for Lead reduction requirements under NSF/ANSI Standard 53 as tested by Pace Analytical Services, Inc.

NSF is a registered trademark of NSF International.

05/14

JENNAIR

REFRIGERATION

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE

IS REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address, and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase, including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed without

service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide or visit https://producthelp.jennair.com.

2. All warranty service is provided exclusively by our authorized JennAir Service Providers. In the U.S. and Canada, direct all requests

for warranty service to:

JennAir Customer eXperience Center

1-800-JENNAIR (1-800-536-6247).

If outside the 50 United States or Canada, contact your authorized JennAir dealer to determine whether another warranty applies.

TWELVE YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

TWO YEAR LIMITED WARRANTY

For two year from the date of purchase, when this major appliance is

installed, operated, and maintained according to instructions attached to

or furnished with the product, JennAir brand of Whirlpool Corporation or

Whirlpool Canada LP (hereafter “JennAir”) will pay for factory specied

replacement parts and repair labor to correct defects in materials or

workmanship that existed when this major appliance was purchased or, at

its sole discretion, replace the product. In the event of product replacement,

your appliance will be warranted for the remaining term of the original unit’s

warranty period.

THIRD THROUGH SIXTH YEAR LIMITED WARRANTY

(SEALED REFRIGERATION SYSTEM ONLY)

In the third through sixth year from the date of purchase, when this major

appliance is installed, operated and maintained according to instructions

attached to or furnished with the product, JennAir brand will pay for factory

specied replacement parts and repair labor for the following components

to correct non-cosmetic defects in materials or workmanship in the sealed

refrigeration system (includes compressor, evaporator, condenser, dryer and

connecting tubing) that existed when this major appliance was purchased.

SEVENTH THROUGH TWELFTH YEAR LIMITED WARRANTY

(SEALED REFRIGERATION SYSTEM ONLY - LABOR NOT INCLUDED))

In the seventh through twelfth year from the date of purchase, when

this major appliance is installed, operated and maintained according to

instructions attached to or furnished with the product, JennAir brand will

pay for factory specied replacement parts for the following components

to correct defects in materials or workmanship in the sealed refrigeration

system (includes compressor, evaporator, condenser, dryer and connecting

tubing) that existed when this major appliance was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a JennAir designated service company.

This limited warranty is valid only in the United States or Canada and

applies only when the major appliance is used in the country in which it

was purchased. This limited warranty is effective from the date of original

consumer purchase. Proof of original purchase date is required to obtain

service under this limited warranty.

1. Commercial, non-residential, or multiple-family use, or use

inconsistent with published user, operator, or installation

instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or

installation, installation not in accordance with electrical or

plumbing codes, or correction of household electrical or

plumbing (e.g., house wiring, fuses, or water inlet hoses).

4. Consumable parts (e.g., light bulbs, batteries, air or water

lters, preservation solutions).

5. Damage from accident, misuse, abuse, re, oods, acts of

God, or use with products not approved by JennAir.

6. Repairs to parts or systems to correct product damage

or defects caused by unauthorized service, alteration, or

modication of the appliance.

7. Cosmetic damage, including scratches, dents, chips, and

other damage to the appliance nishes, unless such damage

results from defects in materials and workmanship and is

reported to JennAir within 30 days.

8. Discoloration, rust, or oxidation of surfaces resulting from

caustic or corrosive environments including, but not limited

to, high salt concentrations, high moisture or humidity, or

exposure to chemicals.

9. Food or medicine loss due to product failure.

10. Pickup or delivery. This product is intended for in-home repair.

11. Travel or transportation expenses for service in remote

locations where an authorized JennAir servicer is not available.

12. Removal or reinstallation of inaccessible appliances or built-

in xtures (e.g., trim, decorative panels, ooring, cabinetry,

islands, countertops, drywall) that interfere with servicing,

removal, or replacement of the product.

13. Service or parts for appliances with original model/serial

numbers removed, altered, or not easily determined.

The cost of repair or replacement under these excluded

circumstances shall be borne by thecustomer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO TWELVE YEARS OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do

not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This warranty

gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

JennAir makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask JennAir or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES: EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENNAIR

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation

of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specic legal rights,

and you also may have other rights that vary from state to state or province to province.

SÉCURITÉ DU RÉFRIGÉRATEUR

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

AVERTISSEMENT :

Pour réduire le risque d’incendie, de choc électrique ou de blessure dans le cadre de l’utilisation du

réfrigérateur, suivre les consignes de base suivantes :

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

CONSERVEZ CES INSTRUCTIONS

■

Brancher sur une prise de terre (reliée à la masse).

■

Ne pas retirer la broche de terre.

■

Ne pas utiliser d’adaptateur.

■

Ne pas utiliser de rallonge.

■ Débrancher la source de courant électrique avant l'entretien.

■ Replacer pièces et panneaux avant de faire la remise en marche.

■ Enlever les portes de votre vieux réfrigérateur.

■ Utiliser un produit de nettoyage ininflammable.

■

Ne pas utiliser ou conserver d’essence ni de liquides ou gaz

inflammables à proximité de cet ou d’autres appareils électriques. Les

fumées peuvent causer des incendies ou des explosions.

■

Ne pas conserver de substances explosives, par exemple des bombes

aérosols contenant un agent propulseur, dans ce réfrigérateur.

■

Ne pas utiliser ni placer dans les compartiments du réfrigérateur des

dispositifs électriques d’un type autre que celui expressément autorisé

par le fabricant.

■ Utiliser deux ou plus de personnes pour déplacer et installer le

réfrigérateur.

■ Débrancher le réfrigérateur avant l'installation de la machine à

glaçons (seulement pour modèles prêts à recevoir une machine

à glaçons).

■

Un technicien qualifié doit installer le tuyau d’eau et le

distributeur de glaçons.

Consulter les instructions

d’installation fournies avec la trousse de machine à

glaçons IC13B pour tous les détails.

■

Raccorder uniquement à une arrivée d’eau potable.

■ Utiliser un verre robuste pour prendre des glaçons (sur

certains modèles).

■ Cet appareil ne convient pas à une utilisation par des

personnes (y compris des enfants) à capacités physiques,

sensorielles ou mentales réduites, ou possédant un

manque d'expérience et de connaissances, à moins

qu'elles ne soient placées sous supervision ou qu'elles

aient reçu des instructions concernant l’utilisation de

l'appareil par une personne responsable de leur sécurité.

■ Les enfants doivent être placés sous surveillance afin de

s'assurer qu'ils ne jouent pas avec l'appareil.

■

Pour éviter le risque que des enfants restent enfermés à

l’intérieur et s’asphyxient, ne pas les laisser jouer ou se cacher

dans le réfrigérateur.

■

Si le cordon d’alimentation est endommagé, il doit être remplacé

par le fabricant ou son technicien d’entretien ou une personne

Mise au rebut du vieux réfrigérateur

IMPORTANT: Le risque qu’un enfant puisse se retrouver coincé

et suffoquer n’est pas chose du passé. Les réfrigérateurs jetés ou

abandonnés restent dangereux, même s’ils ne restent à l’extérieur

que pour “quelques jours seulement”. Si l’ancien réfrigérateur doit

être mis au rebut, suivre les instructions suivantes an d’éviter les

accidents.

Avant de jeter l’ancien réfrigérateur ou congélateur:

■ Enlever les portes.

■ Laisser les tablettes en place de sorte que les enfants ne

puissent pas y pénétrer facilement.

AVANT UTILISATION

Retrait des matériaux d’emballage

■ Enlever tout résidu de ruban adhésif et de colle des surfaces

du réfrigérateur avant de le mettre en marche. Frotter une

petite quantité de savon liquide à vaisselle sur l’adhésif avec

les doigts. Rincer à l’eau tiède et sécher.

■ Ne pas utiliser d’instruments coupants, d’alcool à friction,

de liquides inammables ou de nettoyants abrasifs pour

enlever le ruban adhésif ou la colle. Ces produits peuvent

endommager la surface du réfrigérateur. Pour plus de

renseignements, voir la section “Sécurité du réfrigérateur”.

■ Éliminer/recycler tous les matériaux d’emballage.

Nettoyage avant utilisation

Après avoir enlevé tous les matériaux d’emballage, nettoyer

l’intérieur du réfrigérateur avant de l’utiliser. Voir les instructions

de nettoyage dans la section “Entretien du réfrigérateur”.

Spécications de l’alimentation en eau

Lire toutes les instructions avant de commencer.

IMPORTANT:

■ Lors de l’installation du réfrigérateur, la conduite d’eau de

la source d’alimentation en eau devrait avoir été connectée

au réfrigérateur. Si le réfrigérateur n’est pas connecté à une

source d’alimentation en eau, voir le point “Raccordement

de la canalisation d’eau” dans les Instructions d’installation.

Encas de questions au sujet du raccordement en eau,

consulter la section “Dépannage” ou faire appel à un

plombierqualié agréé.

■ Si on doit mettre en marche le réfrigérateur avant que la

canalisation d’eau ne soit connectée, placer la machine à

glaçons à OFF (arrêt). Voir la section “Machine à glaçons

etbac d’entreposage”.

■ Toutes les installations doivent être conformes aux exigences

des codes locaux de plomberie.

AVERTISSEMENT

Risque de suffoquer

Enlever les portes de votre vieux réfrigérateur.

Le non-respect de cette instruction peut causer

un décès ou des lésions cérébrales.

Renseignements importants à propos de la mise au

rebut des fluides réfrigérants :

Mettre le réfrigérateur au rebut conformément à la

réglementation fédérale et locale. Les fluides réfrigérants

doivent être évacués par un technicien certifié et agréé par

l’EPA conformément aux procédures établies.

AVERTISSEMENT

Risque du poids excessif

Utiliser deux ou plus de personnes pour déplacer et

installer le réfrigérateur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Déplacement de votre réfrigérateur :

Votre réfrigérateur est lourd. Lors du déplacement de votre

réfrigérateur pour le nettoyage ou un entretien ou réparation,

veiller à recouvrir le plancher avec du carton ou un panneau

de fibres dures pour éviter qu'il ne subisse tout dommage.

Toujours tirer le réfrigérateur tout droit lors de son

déplacement. Ne pas incliner le réfrigérateur d’un côté ou de

l’autre ni le “faire marcher” en essayant de le déplacer car le

plancher pourrait être endommagé.

Importants renseignements à savoir au sujet des tablettes

et des couvercles en verre :

Ne pas nettoyer les tablettes ou couvercles en verre avec de

l’eau tiède quand ils sont froids. Les tablettes et les

couvercles peuvent se briser s'ils sont exposés à des

changements soudains de température ou à un impact tel

que coup brusque. Le verre trempé est conçu pour éclater

en d’innombrables pièces minuscules. Ceci est normal. Les

tablettes et les couvercles en verre sont lourds. Les saisir à

deux mains lors de leur dépose afin d'éviter de les faire

tomber.

La page est en cours de chargement...

JennAir JF36NXFXDE Le manuel du propriétaire

Marque: JennAir

Modèle: JF36NXFXDE

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

JF42NXFXDE

Télécharger le PDF

rapport

dans d''autres langues

English: JennAir JF36NXFXDE Owner's manual
español: JennAir JF36NXFXDE El manual del propietario

JennAir JF36NXFXDE Le manuel du propriétaire

Ce manuel convient également à

JennAir JF36NXFXDE Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents