SportsArt N961 Le manuel du propriétaire

N961 OWNER’S MANUAL CONTENTS

1. INTRODUCTION ........................................................................... 2

2. SAFETY PRECAUTIONS ............................................................. 3

3. LIST OF PARTS ............................................................................. 4

4. ASSEMBLE THE PRODUCT ......................................................... 6

STEP 1 Install the Main Frame .................................................................. 6

STEP 2 Install the Handles ...................................................................... 7

STEP 3 Install the Leg Cushion ............................................................... 8

STEP 4 Install the Foot Covers ................................................................ 9

STEP 5 Install the Storage Tray ............................................................... 10

STEP 6 Install the Cap Nut ..................................................................... 11

STEP 7 Secure the Product ..................................................................... 12

STEP 8 Belt Tension Adjustment Instructions ............................................... 14

STEP 9 Minor Weight Stack Instructions .................................................... 15

STEP 10 Unit Inspection

..........................................................................16

5. OPERATE THE PRODUCT ............................................................. 17

OPERATION Safety Operating Area ........................................................... 17

OPERATION Exercising Instructions .......................................................... 18

OPERATION Operate the Product ............................................................. 19

6. MAINTENANCE ............................................................................... 20

MAINTENANCE Safety Precautions ......................................................... 20

MAINTENANCE Guide Rod Cleaning and Lubricating .................................. 21

MAINTENANCE Important Note ............................................................... 22

MAINTENANCE Schedule ..................................................................... 23

MAINTENANCE Task List ...................................................................... 24

MAINTENANCE Maintenance Log ............................................................ 25

7. CONSIGNES DE SÉCURITÉ IMPORTANTES ............................... 26

8. APPENDIXES ................................................................................. 27

APPENDIXES Exploded Diagram ............................................................ 27

2

1. INTRODUCTION

Congratulations on the purchase of a high quality SportsArt product, the N961 Total

Hip machine. Constructed of high quality materials and designed for years of reliable

performance, this product was made for full commercial use.

Before this product is assembled or operated, we recommend that you familiarize

yourself with this manual. Understanding the correct assembly and operation of

this product will help ensure that exercisers obtain their tness goals safely and

successfully.

3

2. SAFETY PRECAUTIONS

This product was designed and built for optimum safety. However certain

precautions apply during the use of this product. Please note the following safety

precautions:

• Please read the entire manual before assembly and operation. Make

sure the product is installed and operated as instructed in this manual.

• Assemble and operate the product on a solid, level surface. Do not use

outdoors or near water, including pools and saunas.

• Check the product before every use. Make sure all parts are assembled,

and all fasteners are tightened. Do not use the product if it is disassembled

in any way.

• Wear proper workout clothing. Do not wear loose clothing. Do not wear

shoes with leather soles or high heels. Tie all long hair back. Do not go

barefoot on this product.

• Keep away from moving parts. Moving parts may or may not stop

immediately if an object becomes caught or impedes normal motion.

• Use this product only for its intended purpose as described in this manual.

• Be careful when mounting and dismounting the unit.

• Never operate this product if it has been damaged in any way. If it is

not working properly, or has been dropped or damaged, contact a service

technician for repairs.

• Do not use accessories or parts that are not specically recommended

by the manufacturer (SportsArt) . Such parts might cause injuries or cause

the unit to fail and void the warranty. We will not be responsible for any

safety issue that arises due to the misuse of accessories or parts. At the

same time, we will terminate the warranty terms of this equipment.

• This product is not intended for use by persons (including children 12

or younger) with reduced physical, sensory, or mental capabilities, or by

people who are otherwise decient in product knowledge or experience. If

such people use this product, they should be given training and be super-

vised at all times by someone responsible for their safety.

• Children ages 12 or younger should be supervised to ensure that they

do not play on or near the product.

• Maintenance and repair must be performed by trained service person-

nel only. Improper maintenance would not only damage the machine, but

also may present a danger to the exerciser.

• The user weight limit for this product is 227 kg (500 lb).

• Warning that any of the adjustment devices that could interfere with the

user’s movement should not be left projecting.

CAUTION: If you feel any pain or any abnormal sensations, STOP YOUR

WORKOUT and consult your physician immediately. Work within your

recommended exercise level. DO NOT work to exhaustion. Before beginning

any exercise program, you should consult with your doctor. It is recommended that

you undergo a complete physical examination.

Over exercise may result in serious injury or death. If you feel faint, stop exercising

immediately.

*NOTE: Each machine provides a different resistance ratio of weight stack.

4

3. LIST OF PARTS

Assembly Parts

No. Name Qty. No. Name Qty.

A1 Weight Stack Frame 1 A6 118 Oval Foot Cover A 7

A2 Support Frame 1 A7 118 Oval Foot Cover B 7

A3

Leg Cushion 1 A8 Storage Tray 1

A4 Left Handle 1 A9 Ground Fixing Bracket 1

A5 Right Handle 1 A10 U Clip 1

5

Components In the Hardware Kit

No. Name Qty. Specication Notes

10 Cover cap 1 D23*t8.8

11 Push rivets 14

L-shaped Allen wrench 1 (M5)

L-shaped Allen wrench 1 (M6)

Double open-end wrench 1 (8*17)

Double open-end wrench 1 (8*10)

Double open-end wrench 1 (13.2*15.2)

Double open-end wrench 1 (17*23)

19 Cap nut

Components on the Product

No. Name Specication Notes

20

Hex screw M10*P1.5*L35

Spring washer M10

Washer D16*d10.2*t1.0

Nylon hex nut M10

21

Round head hex screws M8*P1.25*L15

Spring washer M8

Handle washer D24*d8.3*t2.0

22

Round head inner hex screw M8*P1.25*L20

Washer D40*d8.5*t3.0

23

Fixed plate Foam included

Round head inner hex screw M8*P1.25*L15

Flat washer D17*d8.3*t2

Nylon hex nut M8

25

Mushroom top Phillips screw

(heat treatment)

M5*0.8*L15

Flat washer D13*d6*t1.0

6

4. ASSEMBLE THE PRODUCT

Follow instructions below to assemble this product. Note that in this manual

the words “left” and “right” are used to refer to the product and its parts. As

such, these designations correspond to the “left” and “right” sides of a person

in position to exercise on this product. Also, for brevity, the word “screws” or

“nuts” is used where washers and other hardware may be involved.

STEP 1 Install the Main Frame

Due to safety concerns, a minimum of three people are required for assembly

of the equipment.

(a) Remove screws (20) from the support frame (A2) and the weight stack

frame (A1).

(b) Have one person stand at the back of the equipment and hold the weight

stack frame (A1), then install the support frame (A2) to the weight stack

frame (A1) with screws (20).

7

STEP 2 Install the Handles

(a) Remove screws (21) from the weight stack frame (A1).

(b) Attach both left and right handles (A4)(A5) onto the weight stack frame

(A1), then use screws (21) to secure the assembly.

8

STEP 3 Install the Leg Cushion

(a) Remove the screws (22) from the leg cushion (A3).

(b) Secure the rotational connector of the leg cushion (A3) to the weight stack

frame (A1) using screws (22), and then put the cork cover (10) on.

Note: Make the knob is at the bottom of the leg cushion, and the rotational

connector is aligned with the 4th hole during the assembling process.

9

STEP 4 Secure the Foot Covers

(a) Attach the oval foot covers (A6)(A7) onto the weight stack frame (A1) and

support frame (A2) legs. Align the ends and using push rivets (10) to secure

the foot covers together.

Note: If the holes don’t match up while installing the oval foot covers, change

their direction and put them back in a new way. The cutout should face the

inner side of the foot tube.

10

STEP 5 Install the Storage Tray

(a) Locate the position where the storage tray (A8) attaches to the weight

stack frame (A1), then remove the screws (23) from the weight stack

frame.

(b) Secure the storage tray (A8) to the main frame (A1) using screws (23).

11

STEP 6 Install the Cap Nut

After completing the assembly, install the cap nut (19) as shown in the

following figure.

Note: Make sure the cap nuts and screws are size-matching.

12

STEP 7 Secure the Product

Please follow the instructions (a) through (c) to secure the unit to make sure

it is firmly fixed to the floor when operating.

(a) Remove screws (25) from the ground fixing bracket (A9).

(b) Insert the U clip (A10) onto the machine (Make sure the U clip is in

the correct direction as shown below), and then secure the ground fixing

bracket (A9) with screws.

(c) Secure the ground fixing bracket to the floor with the ground fixing bolt,

nut and washer.

(Note: The screw hole of ground fixing bracket is Ø9mm, make certain you

use the suitable ground fixing bolt and drill the proper hole on the floor.)

(b)

(a)

(c)

13

*If the ground has a slight incline or is uneven, slipping some kind of shim

under one of the legs as shown below. (Several shims are given away free

enclosed with the equipment).

14

STEP 8 Belt Tension Adjustment Instructions

1. After finishing installation and the final positioning of the equipment, per

form the whole-machine-test to ensure it works properly.

2. If the belt tension is incorrect, perform the modification adjustment: First

loosen nut A as shown then adjust nut B (as shown in the figure). Note

that if the belt is too long, adjust the nut down, and vice versa. Once

the belt reaches the desired position, tighten nut A to secure the belt

length.

Note: After adjusting the belt, the gap between nut A and B must be within

35mm(1.4”). If the gap still exceeds the 35mm limit, you need to perform the

following modifications:

A. Loosen the screws as pointed by the arrow-C, and adjust the belt to the

proper length.

B. Tighten the screws pointed by the arrow-C.

3. After finishing the above adjustments, perform the whole- machine -test

again to ensure the unit functions properly.

15

STEP 9 Minor Weight Stack Instructions

To adjust the minor weight stack, insert the upper pin to add 3.5Lbs/1.5kgs

or the lower pin to add 6.5Lbs/3kgs. When the minor weights are not in use,

pull the pin to release the weight.

16

STEP 10 Unit Inspection

After completing the assembly or regular maintenance, please follow

instructions (a) through (c) to inspect the unit. If the unit is disassembled or

has been damaged in any way, it might cause injuries or cause the unit to

fail.

(a) Make sure the unit is steady and is on a level surface. If not, make ad-

justments according to the instructions “Secure the Unit” in this manual.

(b) Make sure all parts are assembled and all fasteners are tightened.

(c) Please follow operating instructions to test operation and make sure that

the equipment is working properly. (Please refer to “Operate the Product”

in this manual.)

17

5. OPERATION THE PRODUCT

This section includes operational instructions.

OPERATION Safety Operating Area

(a) Safety clearance required is shown below. Do not allow access for peo-

ple to near this area when operating.

(b) Noise emission under load is higher than without load.

(c) Over exercise or improper workout position may result in serious injury.

(d) This equipment is intended to strengthen the muscles that surround your

hips and legs.

18

OPERATION Safety Operating Area

(a) Select the appropriate weight stacks according to your recommended

exercise level.

(b) Adjust the rotational connector and leg cushion to the most comfor-

table position and make sure the knob is engaged to secure the posi-

tion.

(c) Perform the exercise in a controlled manner. Inhale when pushing up

against resistance and exhale when returning to original position.

* Always workout at a level that is tolerable, to stay in the proper training

zone for your body. DO NOT work to exhaustion.

* Use equipment ONLY under the supervision of trained and qualified ins-

tructors for safety reasons.

* Please follow operating instructions on the product sticker to test opera-

tion and make sure the equipment is working properly.

19

OPERATION Operate the Product

(a). The rotator adjusting pin (as shown in area A) is used to adjust the posi-

tion of the rotator.

(b). The plate adjusting pin (as shown in area B) is used to adjust the position

of the plate.

Note: Make sure the leg cushion is locked and secured before exercising.

20

6. MAINTENANCE

This section covers maintenance topics and includes a maintenance

schedule, task list, and log.

MAINTENANCE Safety Precautions

● Please follow standard safety precautions when servicing on this pro-

duct.

● Do NOT use a damp towel to clean the product and do perform the fol-

lowing maintenances.

● Do NOT use cleaners with alcohol, ammonia, or other damaging chemi-

cals.The use of such chemicals can damage the product and void the

warranty. Never spray or pour any liquid directly onto the product. Doing

so can damage components and void the warranty.

● Use a clean, lint-free towel, dampened with a mixture of Simple Green®all-

purpose cleaner, to thoroughly clean the handlebar and the console.

● This product has moving parts that can be hazardous. Exercise caution-

when maintaining, operating, or moving this product.

● Do not use accessories or parts that are not specically recommend-

edby the manufacturer (SportsArt) . Such parts might cause injuries or

cause the unit to fail and void the warranty. We will not be responsible

for anysafety issue that arises due to the misuse of accessories or parts.

At the same time, we will terminate the warranty terms of this equipment.

● Maintenance and repair must be performed by trained service personnel

only. Improper maintenance would not only damage the machine, but

also may present a danger to the exerciser.

● Keep this product out of use until maintenance is completed.

La page charge ...

SportsArt N961 Le manuel du propriétaire

SportsArt N961 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents