Sony Sony VPL-CX10 Manuel utilisateur

Operating Instructions

Mode d’emploi

Manual de instrucciones

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\01COV-

VPLCS10.CX10WW\01COV.fm

masterpage:Left

4-079-300-12 (2)

LCD Data Projector

GB

FR

ES

VPL-CS10

VPL-CX10

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\02REG.fm

masterpage:Left

GB

2

VPL-CS10/CX10

4-079-300-12 (2)

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not

open the cabinet. Refer servicing to

qualified personnel only.

For the customers in the USA

If you have any questions about this product,

you may contact:

Sony Electronics Inc.

Attn: Business Information Center (BIC)

12451 Gateway Boulevard

Ft. Myers, Florida 33913

Telephone No.: 800-686-7669

The number below is for FCC related

matters only.

Declaration of Conformity

Trade Name: SONY

Model No.: VPL-CS10, VPL-CX10

Responsible Party: Sony Electronics Inc.

Address: 680 Kinderkamack Road, NJ

07649 U.S.A.

Telephone No.: 201-930-6972

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and (2)

this device must accept any interference

received, including interference that may

cause undesired operation.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct

the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/

TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

This symbol is intended to

alert the user to the presence

of uninsulated “dangerous

voltage” within the

product’s enclosure that may

be of sufficient magnitude to

constitute a risk of electric

shock to persons.

This symbol is intended to

alert the user to the presence

of important operating and

maintenance (servicing)

instructions in the literature

accompanying the

appliance.

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\02REG.fm

masterpage:Left

3

GB

VPL-CS10/CX10

4-079-300-12 (2)

For the customers in Canada

This Class B digital apparatus complies with

Canadian ICES-003.

For the customers in the United

Kingdom

WARNING

THIS APPARATUS MUST BE

EARTHED

IMPORTANT

The wires in this mains lead are coloured in

accordance with the following code:

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead

of this apparatus may not correspond with

the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured green-and-

yellow must be connected to the terminal in

the plug which is marked by the letter E or

by the safety earth symbol I or coloured

green or green-and-yellow.

The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black. The wire

which is coloured brown must be connected

to the terminal which is marked with the

letter L or coloured red.

Voor de klanten in Nederland

Bij dit product zijn batterijen

geleverd. Wanneer deze leeg

zijn, moet u ze niet

weggooien maar inleveren

als KCA.

The socket-outlet should be installed near

the equipment and be easily accessible.

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\02REG.fm

masterpage:Left

GB

4

VPL-CS10/CX10

4-079-300-12 (2)

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\01COVTOC.fm

masterpage:Left

5

GB

Table of Contents

GB

Overview

Precautions .........................................6

Features ..............................................7

Location and Function of Controls ...9

Front/Left Side .............................9

Rear/Right Side/Bottom ...............9

Control Panel ..............................11

Connector Panel .........................12

Remote Commander ...................13

Setting Up and Projecting

Installing the Projector .....................15

Connecting the Projector ..................16

Connecting with a Computer ......16

Connecting with a VCR or 15k

RGB/Component

Equipment ......................18

Selecting the Menu Language ..........20

Projecting .........................................22

Effective Tools for Your

Presentation .....................25

Adjustments and Settings

Using the Menu

Using the MENU .............................26

The PICTURE CTRL Menu ............27

The INPUT SETTING Menu ...........28

The SET SETTING Menu ...............30

Maintenance

Maintenance .................................... 31

Replacing the Lamp ................... 31

Cleaning the Air Filter ............... 32

Troubleshooting .............................. 33

Warning Messages ..................... 35

Caution Messages ...................... 35

Other

Installation Example ........................ 36

Notes on Installation ........................ 38

Unsuitable Installation ............... 38

Unsuitable Conditions ................ 38

Specifications .................................. 39

Index ............................................... 47

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

GB

6

Precautions

VPL-CS10/CX10

4-079-300-12 (2)

B

Overview

Precautions

On safety

• Check that the operating voltage of your

unit is identical with the voltage of your

local power supply.

• Should any liquid or solid object fall into

the cabinet, unplug the unit and have it

checked by qualified personnel before

operating it further.

• Unplug the unit from the wall outlet if it is

not to be used for several days.

• To disconnect the cord, pull it out by the

plug. Never pull the cord itself.

• The wall outlet should be near the unit and

easily accessible.

• The unit is not disconnected to the AC

power source (mains) as long as it is

connected to the wall outlet, even if the

unit itself has been turned off.

• Do not look into the lens while the lamp is

on.

• Do not place your hand or objects near the

ventilation holes. The air coming out is

hot.

• Be careful not to catch your fingers by the

adjuster when you lift up the projector. Do

not push hard on the top of the projector

with the adjuster out.

• Install the projector on the floor or ceiling.

Any other installation causes a

mulfunction such as color irregularity or

shortened lamp life.

• For ceiling installation, consult with

qualified Sony personnel.

On illumination

• To obtain the best picture, the front of the

screen should not be exposed to direct

lighting or sunlight.

• Ceiling-mounted spot lighting is

recommended. Use a cover over

fluorescent lamps to avoid lowering the

contrast ratio.

• Cover any windows that face the screen

with opaque draperies.

• It is desirable to install the projector in a

room where floor and walls are not of

light-reflecting material. If the floor and

walls are of reflecting material, it is

recommended that the carpet and wall

paper be changed to a dark color.

On preventing internal heat build-

up

After you turn off the power with the I / 1

key, do not disconnect the unit from the wall

outlet while the cooling fan is still running.

Caution

The projector is equipped with ventilation

holes (intake) and ventilation holes

(exhaust). Do not block or place anything

near these holes, or internal heat build-up

may occur, causing picture degradation or

damage to the projector.

On cleaning

• To keep the cabinet looking new,

periodically clean it with a soft cloth.

Stubborn stains may be removed with a

cloth lightly dampened with a mild

detergent solution. Never use strong

solvents, such as thinner, benzene, or

abrasive cleansers, since these will

damage the cabinet.

• Avoid touching the lens. To remove dust

on the lens, use a soft dry cloth. Do not use

a damp cloth, detergent solution, or

thinner.

• Clean the filter at regular intervals.

On repacking

• Save the original shipping carton and

packing material; they will come in handy

if you ever have to ship your unit. For

maximum protection, repack your unit as

it was originally packed at the factory.

On LCD projector

• The LCD projector is manufactured using

high-precision technology. You may,

however, see tiny black points and/or

bright points (red, blue, or green) that

continuously appear on the LCD projector.

This is a normal result of the

manufacturing process and does not

indicate a malfunction.

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

7

GB

Features

Overview

Features

High portability

• Light weight/small size

This projector has been miniaturized to

approx. 3.3 kg (7 lb 4 oz) in weight and

A4-file size. A carrying handle is equipped

with the projector, so you can carry it

easily with your computer.

Reduced noise

Because the projector uses a new cooling

mechanism, noise has been reduced.

High brightness, high picture

quality

• High brightness

Adopting the new developed optical

system and the 132 W UHP lamp allows

high brightness (VPL-CS10: light output

1000 ANSI lumen, VPL-CX10: light

output 1200 ANSI lumen) and excellent

uniformity on the picture.

• High resolution

VPL-CS10

Three 0.9-inch, about 480,000 pixel,

SVGA panels provide a resolution of 800

× 600 dots for RGB input and 600

horizontal TV lines for video input.

VPL-CX10

Three 0.9-inch, about 790,000 pixel, XGA

panels provide a resolution of 1024 × 768

dots for RGB input and 750 horizontal TV

lines for video input.

Simple setup

• Simple setup with external equipment

This projector is preset for 37 kinds of

input signals. You can project images from

an external signal source just by

connecting the equipment with the

supplied cable and pushing the APA key.

• Compatible with USB (Universal Serial

Bus) hub function

You can connect an USB equipment (e.g.,

USB mouse) to the projector, and also

control the projector by using the

application software (CD-ROM) supplied

with the projector from a computer

operated with Windows 98, Windows 98

SE or Windows 2000. Using this

application software, you can open a file

you want to use for your presentation with

the supplied Remote Commander.

Easy presentation

• Multi functional Remote Commander

with mouse control functions

You can operate a computer connected to

this projector with the Remote

Commander since the unit has a build-in

mouse receiver.

• Digital ZOOM and FUNCTION keys

on the Remote Commander

The Digital ZOOM allows you to enhance

your presentation by zooming in on the

image. You can allocate a presentation file

to the FUNCTION keys by using the

application software (CD-ROM) supplied

with the projector. Just pressing the

FUNCTION key opens the file

immediately.

Accepts various input signals

• Scan converter loaded

This projector has a build-in scan

converter that converts the input signal

within 800 × 600 dots (VPL-CS10) or

1024 × 768 dots (VPL-CX10).

• Compatible input signals

This projector accepts video signals of

composite, S video, and component as

well as 15k RGB, VGA, SVGA, XGA,

and SXGA signals, which all can be

displayed.

• Compatible with six color systems

NTSC, PAL, SECAM, NTSC

4.43

1)

, PAL-

M, or PAL-N color system can be selected

automatically or manually.

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

GB

8

Features

......................................................................

.

• Windows is a registered trademark of

Microsoft Corporation in the United States

and/or other countries.

• VGA, SVGA, XGA, and SXGA are

registered trademarks of the International

Business Machines Corporation, U.S.A.

• Macintosh is a registered trademark of

Apple Computer, Inc.

• IBM PC/AT is a registered trademark of

International Business Machines

Corporation, U.S.A.

• VESA is a registered trademark of Video

Electronics Standard Association.

• Display Data Channel is a trademark of

Video Electronics Standard Association.

• PC-98 is a trademark of NEC Corporation.

1)NTSC

4.43

is the color system used when

playing back a video recorded on NTSC

on a NTSC

4.43

system VCR.

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

9

GB

Location and Function of Controls

Overview

Location and

Function of Controls

1 Zoom ring

Adjusts the picture size.

2 Focus ring

Adjusts the picture focus.

3 Ventilation holes (exhaust)

4 Lens

5 Adjuster

When a picture is projected on the

exterior of the screen, adjust the picture

using this adjuster.

For details on how to use the adjusters,

see “How to use the adjuster” on page

10.

6 Ventilation holes (intake)/air

filter cover

• Do not place anything near the

ventilation holes as it may cause internal

heat build-up.

• Do not place your hand or objects near

the ventilation holes as it may cause the

air coming out heat build-up.

• To maintain optimal performance, clean

the air filter every 300 hours.

7 Front remote control detector

(SIRCS receiver)

8 Control panel

For details, see “Control Panel” on

page 11.

9 Speakers

q;

q;q;

q; Rear remote control detector

(SIRCS receiver)

qa

qaqa

qa Connector panel

For details, see “Connector Panel” on

page 12.

qs

qsqs

qs AC IN socket

Connects the supplied AC power cord.

Front/Left Side

Rear/Right Side/Bottom

1

7

6

5

2

3

4

Notes

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

GB

10

Location and Function of Controls

qd

qdqd

qd Security lock

Connects to an optional security cable

(Kensington’s).

qf

qfqf

qf Ventillation holes (intake,

bottom)

qg

qgqg

qg Lamp cover (bottom)

qh

qhqh

qh RELEASE (adjuster adjustment)

button

For details, see “How to use the

adjuster” on page 10.

qj

qjqj

qj Carrying handle

Pull up the handle from the projector for

carrying.

qk

qkqk

qk Ventilation holes (intake, rear)

How to use the adjuster

To adjust the height

Adjust the height of the projector as follows:

1

Lift the projector and press the

RELEASE button.

The adjuster will extend from the

projector.

2

While pressing the button, lower the

projector. Then, release the button.

For fine adjustment, turn the adjusters to

the right and the left.

• Do not remove the adjusters from the

projector. Do not use the projector with the

adjusters removed.

• Be careful not to let the projector down on

your fingers.

• Do not push hard on the top of the projector

with the adjusters out.

The security lock corresponds to

Kensington’s MicroSaver

®

Security

System.

If you require further information,

contact

Kensington

2855 Campus Drive

San Mateo, CA 94403

In North America

Phone: 800-235-6708

Fax: 800-247-1317

Outside North America

Phone: 847-541-9500

Home page address:

http://www.kensington.com/

Notes

RELEASE button

to raise the

projector

to lower the

projector

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

11

GB

Location and Function of Controls

Overview

1 I / 1

11

1 (ON/STANDBY) key

Turns on and off the projector when the

projector is in standby mode. The ON/

STANDBY indicator lights in green

when the power is turned on.

When turning off the power, press

the I / 1 key twice following the

message on the screen, or press and hold

the key for about one second.

For details on steps for turning off the

power, see “To turn off the power” on

page 24.

2 INPUT key

Selects the input signal. Each time you

press the key, the input signal switches

as follows:

3 APA (Auto Pixel Alignment) key

Adjusts a picture clearest automatically

while a signal is input from a computer.

4 VOLUME +/– keys

Adjust the volume of the built-in

speakers.

+ : Increases the volume.

– :

Decreases the volume.

5 Indicators

• LAMP/COVER: Lights up or flashes

under the following conditions:

– Lights up when the lamp has

reached the end of its life or

becomes a high temperature.

– Flashes when the lamp cover or air

filter cover is not secured firmly.

• FAN/TEMP (Temperature): Lights

up or flashes under the following

conditions:

– Lights up when temperature inside

the projector becomes unusually

high.

– Flashes when the fan is broken.

• POWER SAVING: Lights up when

the projector is in power saving mode.

When POWER SAVING in the SET

SETTING menu is set to ON, the

projector goes into power saving mode

if no signal is input for 10 minutes.

Although the lamp goes out, the

cooling fan keeps running. In power

saving mode, any key does not

function for the first 30 seconds. The

power saving mode is canceled when a

signal is input or any key is pressed.

• ON/STANDBY: Lights up or flashes

under the following conditions:

– Lights in red when a AC power cord

is plugged into a wall outlet. Once in

standby mode, you can turn on the

projector with the I / 1 key.

– Lights in green when the power is

turned on.

– Flashes in green while the cooling

fan runs after the power is turned off

with the I / 1 key. The fan runs for

about 60 seconds after the power is

turned off.

The ON/STANDBY indicator

flashes quickly for the first 30

seconds. During this time, you

cannot light up the ON/STANDBY

indicator with the I / 1 key.

For details on the LAMP/COVER and

the FAN/TEMP indicators, see page 35.

6 ENTER key

Enters the settings of items in the menu

system.

Control Panel

RESET ENTER

– VOLUME +

LAMP/

COVER

ON/

STANDBY

FAN/

TEMP

POWER

SAVING

APA INPUT ON/STANDBY

MENU

I / 1

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

GB

12

Location and Function of Controls

7 Arrow keys (M

MM

M/m

mm

m/<

<<

</,

,,

,)

Select the menu or to make various

adjustments.

8 RESET key

Resets the value of an item back to its

factory preset value. This key functions

when the menu or a setting item is

displayed on the screen.

9 MENU key

Displays the on-screen menu. Press

again to clear the menu.

1 INPUT A connector

Connect to external equipment such as a

computer.

• INPUT A connector (HD D-sub 15-

pin, female): Connects to the monitor

output on a computer using the

supplied cable.

When inputting a component or 15k

RGB signal, use an optional cable.

For details, see “To connect a 15k RGB/

Component equipment” on page 19.

• AUDIO (stereo minijack)

connector: Connects to the audio

output of the computer.

• MOUSE connector (6-pin):

Connects to the PS/2 mouse port on a

computer via the supplied mouse

cable, to control the mouse function of

the connected computer.

2 VIDEO IN connector

Connect to external video equipment

such as a VCR.

• S VIDEO (mini DIN 4-pin):

Connects to the S video output (Y/C

video output) of video equipment.

• VIDEO (phono type): Connects to

the composite video output of video

equipment.

• AUDIO (stereo minijack)

connector: Connects to the audio

output of the VCR.

3 CONTROL S IN/PLUG IN

POWER (DC 5V output) jack

Connects to the control S out jack of the

Sony equipment.

Connects to the CONTROL S OUT jack

on the supplied Remote Commander

when using it as a wired Remote

Commander. In this case, you do not

need to install the batteries in the

Remote Commander, since the power is

supplied from this jack.

4 USB connector (USB A-plug for

downstream, 4-pin)

Connect to USB equipment such as a

mouse, camera, etc.

5 USB connector (USB B-plug for

upstream, 4-pin)

Connect to the USB connector on a

computer.

When you connect the projector to the

computer, the projector recognizes the

mouse of the computer connected to the

INPUT A connector and you can control

the mouse function with the supplied

Remote Commander. The supplied

application software can be installed in

the computer attached to this connector.

Connector Panel

INPUT A

CONTROL S

IN / PLUG IN

POWER

VIDEO IN INPUT A

Rear side

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

13

GB

Location and Function of Controls

Overview

The keys that have the same names as those

on the control panel function identically.

You can control a connected computer using

the Remote Commander.

For details, see “To control the computer

using the supplied Remote Commander” on

page 23.

1 I / 1

11

1 key

2 APA (Auto Pixel Alignment) key

3 ENTER key

4 Joystick

Functions as the mouse of the computer

connected to the unit.

5 Arrow (

M

/

m

/

<

/

,

) keys

6 R CLICK key

Functions as the right button on a mouse.

7 FUNCTION 1, 2 keys

These keys function when the supplied

application software is used.

When you connect the projector with a

computer, you can open a file on the

screen by just pressing the FUNCTION

key. This will enhance your

presentation. To use this function,

allocate a file to the FUNCTION key by

using the application software.

For details, see the README file and

the HELP file supplied with the

application software.

8 CONTROL S OUT jack (stereo

minijack)

Connects to the CONTROL S IN jack on

the projector with the connecting cable

(not supplied) when using the Remote

Commander as a wired one. In this case,

you do not need to install the batteries as

the power is supplied via the CONTROL

S IN jack on the projector.

9 RESET (D ZOOM) key

Resets the value of an item back to its

factory preset value or returns the

enlarged image back to its original size.

0 D ZOOM +/–

key

Enlarges the image at a desired location

on the screen.

+: Pressing the + key once highlights

one of the images divided into 16.

Use an arrow key (M/m/</,) to

move the highlight portion to the

point in the image to be enlarged.

Press the + key repeatedly until the

image is enlarged to your

requirements.

–: Pressing the – key reduces an image

that has been enlarged with the D

ZOOM + key.

qa L CLICK key

Functions as the left button on a mouse.

qs MENU key

qd INPUT key

Remote Commander

I / 1

PIC

INPUT

MUTING

MENU ENTER

VOLUME

RESET

FUNCTION

D ZOOM

12

(D ZOOM)

APA

+

–

+

–

R

CLICK

8

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\03OVR.fm

masterpage:Left

GB

14

Location and Function of Controls

qf MUTING PIC key

Cut off the picture. Press again to restore

the picture.

qg VOLUME +/– keys

qh Infrared transmitter

To install batteries

1

Push and slide to open the lid, then

install the two size AA (R6) batteries

(supplied) with the correct polarity.

2

Replace the lid.

Notes on batteries

• Make sure that the battery orientation is

correct when inserting batteries.

• Do not mix an old battery with a new one

or different types of batteries.

• If you do not use the Remote Commander

for a long time, remove the batteries to

avoid damage from battery leakage. If

batteries have leaked, remove them, wipe

and dry the battery compartment, and

replace the batteries with new ones.

Notes on Remote Commander

operation

• Make sure that nothing obstructs the

infrared beam between the Remote

Commander and the remote control

detector on the projector. Direct the

Remote Commander toward the front or

rear remote control detector.

• The operation range is limited. The shorter

the distance between the Remote

Commander and the projector is, the wider

the angle within which the commander can

control the projector becomes.

Be sure to install the

battery from the

#

side.

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\04SET.fm

masterpage:Left

15

GB

Installing the Projector

Setting Up and Projecting

B

Setting Up and Projecting

Installing the Projector

This section describes how to install the projector.

The distance between the lens and the screen varies depending on the size of

the screen. Use the following table as a guide.

For details, see “Installation Example” on page 36.

For details on ceiling installation, consult with qualified Sony personnel (fee

charged).

Unit: m (feet)

Screen size

(inches)

40 60 80 100 120 150 200 300

Minimum

Distance

1.5

(4.8)

2.2

(7.3)

3.0

(9.8)

3.8

(12.4)

4.5

(14.9)

5.7

(18.6)

7.6

(24.9)

11.4

(37.5)

Maximum

Distance

1.8

(5.8)

2.7

(8.8)

3.6

(11.8)

4.5

(14.8)

5.4

(17.8)

6.8

(22.3)

9.1

(29.8)

13.7

(44.9)

Distance between the screen and

the center of the lens

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\04SET.fm

masterpage:Left

GB

16

Connecting the Projector

When making connections, be sure to do the following:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs properly; plugs that are not fully inserted often

generate noise. When pulling out a cable, be sure to pull it out from the plug,

not the cable itself.

This section describes how to connect the projector to a computer.

For more information, refer to the computer’s instruction manual.

• The projector accepts VGA, SVGA, XGA, and SXGA signals. However, we

recommend that you set the output mode of your computer to SVGA (VPL-CS10) or

XGA (VPL-CX10) mode for the external monitor.

• If you set your computer, such as a notebook type, to output the signal to both your

computer’s display and the external monitor, the picture of the external monitor may

not appear properly. Set your computer to output the signal to only the external

monitor.

For details, refer to the operating instructions supplied with your computer.

• Supplied mouse cable may not work properly according to your computer.

• This projector is compatible with a DDC2B (Digital Data Channel 2B). If your

computer is compatible with a DDC, turn the projector on according to the following

procedures.

1 Connect the projector to the computer by using the supplied HD D-sub 15 pin cable.

2 Turn the projector on.

3 Start the computer.

Connecting with a Computer

Notes

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\04SET.fm

masterpage:Left

17

GB

Connecting the Projector

Setting Up and Projecting

To connect an IBM PC/AT compatible computer

When you use a USB mouse and USB equipment

On the USB function

When connecting the projector to a computer by using the USB cable for the

first time, the computer recognizes the following devices automatically.

1 USB hub (general use)

2 USB human interface device (wireless mouse function)

3 USB human interface device (projector control function)

The computer also recognizes the device connected to the downstream

connector on the projector.

Recommended operating environment

When you use the USB function, connect your computer as illustrated above.

This application software and the USB function can be used on a computer

loaded with Windows 98, Windows 98 SE or Windows 2000 preinstall

models.

• As the projector recognizes the USB mouse when the computer is

connected to the USB connector, do not connect anything to the PS/2

mouse port.

• Your computer may not start correctly when connected to the projector

via the USB cable. In this case, disconnect the USB cable, restart the

computer, then connect the computer to the projector using the USB

cable.

• This projector is not guaranteed for suspend, standby mode. When you

use the projector in suspend, standby mode, disconnect the projector

from the USB port on the computer.

• Operations are not guaranteed for all the recommended computer

environments.

Notes

INPUT A

CONTROL S

IN / PLUG IN

POWER

VIDEO IN INPUT A

Rear side

to USB equipment

USB cable A type – B type (supplied)

Stereo audio connecting

cable (not supplied)

HD D-sub

15-pin cable

(supplied)

to USB connector

to monitor output

to audio output

Computer

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\04SET.fm

masterpage:Left

GB

18

Connecting the Projector

When you use a PS/2 mouse port

To connect a Macintosh computer

Use an ADP-20 signal adapter (not supplied). In this case, however, you can

not control the mouse of the computer by the Remote Commander.

This section describes how to connect the projector to a VCR and 15k RGB/

component equipment.

For more information, refer to the instruction manuals of the equipment you

are connecting.

To connect a VCR

Connecting with a VCR or 15k RGB/Component Equipment

INPUT A

CONTROL S

IN / PLUG IN

POWER

VIDEO IN INPUT A

to audio output

Rear side

HD D-sub

15-pin cable

(supplied)

to mouse port

(PS/2)

PS/2 Mouse cable

(supplied)

Stereo audio connecting cable

(not supplied)

to monitor output

Computer

INPUT A

CONTROL S

IN / PLUG IN

POWER

VIDEO IN INPUT A

AV cable (supplied)

S-Video cable (not supplied)

VCR

to video

output

to S video

output

Rear side

to

audio

output

(R/L)

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\04SET.fm

masterpage:Left

19

GB

Connecting the Projector

Setting Up and Projecting

To connect a 15k RGB/Component equipment

• S

et the aspect ratio using ASPECT in the INPUT SETTING menu

according to the input signal.

• When

you connect the unit to 15k RGB/component video equipment,

select RGB or component with the INPUT-A setting in the SET

SETTING menu.

• U

se the composite sync signal when you input the external sync signal

from 15k RGB/component equipment.

Notes

INPUT A

CONTROL S

IN / PLUG IN

POWER

VIDEO IN INPUT A

Rear side

Stereo audio connecting cable (not supplied)

SMF-402 Signal Cable (not supplied)

HD D-sub 15-pin (male) ↔ 3 × phono jack

to audio

output

15k RGB/Component equipment

to RGB/

component

output

VPL-CS10/CX10

4-079-300-12 (2)

D:\Nouhin\W00001VPL-

CS10CX10\4079300122\4079300122VPLCS10CX10WW\02GB-

VPLCS10.CX10WW\04SET.fm

masterpage:Left

GB

20

Selecting the Menu Language

You can select one of seven languages for displaying the menu and other on-

screen displays. The factory setting is English.

1

Plug the AC power cord on the rear side on the projector into a wall outlet.

2

Press the I /

1

key to turn on the projector.

3

Press the MENU key.

The menu appears.

The menu presently selected is shown as a yellow button.

RESET ENTER

– VOLUME +

LAMP/

COVER

ON/

STANDBY

FAN/

TEMP

POWER

SAVING

APA INPUT ON/STANDBY

MENU

I / 1

1

3

4,5,6

2

3

I / 1

PIC

INPUT

MUTING

MENU ENTER

VOLUME

RESET

APA

+

–

+

–

R

CLICK

Front remote control

detector

80

50

PICTURE CTRL

CONTRAST:

BRIGHT:

GAMMA MODE: GRAPHICS

COLOR TEMP: HIGH

INPUT-A

La page charge ...

Sony Sony VPL-CX10 Manuel utilisateur

Ce manuel convient également à

Sony Sony VPL-CX10 Manuel utilisateur

dans d''autres langues

Documents connexes