Dell PowerEdge C6145 Guide de démarrage rapide

Dell PowerEdge

C6145

Getting Started

With Your System

Guide de mise en route du système

Introdução ao Uso do Sistema

Procedimientos iniciales con el sistema

Dell PowerEdge

C6145

Getting Started

With Your System

Notes, Cautions, and Warnings

NOTE:

A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of

data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

______________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission

of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of

Dell Inc. AMD® is a registered trademark and AMD Opteron™ is a trademark of

Advanced Micro Devices, Inc. Red Hat Enterprise Linux® and Enterprise Linux® are

registered trademarks of Red Hat, Inc. in the United States and/or other countries.

Novell® is a registered trademark and SUSE™ is a trademark of Novell Inc. in the United

States and other countries. Citrix® and XenServer® are either registered trademarks or

trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Other trademarks and trade names may be used in this publication to refer to either the

entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Regulatory Model B05S

September 2013 P/N 6HNH8 Rev. A04

Getting Started With Your System | 3

CAUTION: Restricted Access Location

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply:

•

Access can only be gained by service persons or by users

who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

•

Access is through the use of a tool or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

WARNING: Before performing the following procedure, review and follow the

safety instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Tool-Less Rail Solution

WARNING: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the rails. To

avoid personal injury or damage to the system, you must adequately

support the system during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack

equipment must provide sufficient airflow to the system to maintain proper

cooling.

CAUTION: When installing rails in a square-hole rack it is important to

ensure that the square peg slides through the square holes.

Getting Started With Your System | 4

1

Pull on the latch release buttons on the midpoints of the end piece to

open the rail latches.

2

Align the end pieces of the rails on the vertical rack flanges to seat

the pegs in the bottom hole of the first U and the top hole of the

second U. Engage the back end of the rails until the latches lock in

place.

NOTE:

The rails can be used in both square-hole (item 1 in the following figure)

and round-hole racks (item 2 in the following figure).

Figure 1. Pushing the Latch Release Buttons

3

Repeat Step 1 and Step 2 to position and seat the front end pieces on

the vertical flanges.

NOTE:

To remove the rails, pull on the latch release button on the midpoints of

the end piece and unseat each rail.

4

On each vertical rack flange on the back, put two screw bases into

the two square holes right above the rail.

5

Install the chassis stabilizer shipping brackets (optional) on the back

rack flanges and simultaneously tighten the screws.

NOTE:

To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

Getting Started With Your System | 5

Figure 2. Installing the Chassis Stabilizer Shipping Brackets

6

Slide the system into the rack.

7

Tighten the thumbscrews to secure the ears of the system to the front

of the rack flanges.

Figure 3. Installing the Chassis onto the Rack.

Getting Started With Your System | 6

Optional—Connecting the Keyboard, Mouse, and Monitor

Figure 4. Optional—Connecting the Keyboard, Mouse and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to

plug into each connector. Be sure to tighten the screws (if any) on the monitor’s

cable connector.

Getting Started With Your System | 7

Connecting the Power Cable(s)

Figure 5. Connecting the Power Cable

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor. Plug the other end of the

power cables into a grounded electrical outlet or a separate power source such as

an uninterrupted power supply or a power distribution unit.

Getting Started With Your System | 8

Turning on the System

Figure 6. Pressing the Power Button on the Front of the System and the Monitor

Figure 7. Pressing the Power Button on the Back of the System

Press the power button(s) either on the front or back of the system and on the

monitor. The power indicators on the front should light.

Getting Started With Your System | 9

NOTE:

The color of the power indicator on the monitor will vary with the different

monitor models.

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentation for your operating system. Be sure the operating

system is installed before installing hardware or software not purchased with the

system.

NOTE:

For the latest information on supported operating systems, see

dell.com/ossupport

.

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

The Hardware Owner’s Manual provides information about system features and

describes how to troubleshoot the system and install or replace system

components. This document is available at

dell.com/support/manuals

.

Dell systems management application documentation provides information

about installing and using the systems management software. This document is

available online at

dell.com/support/manuals

.

NOTE:

Always check for updates on

dell.com/support/manuals

and read the

updates first because they often supersede information in other documents.

Getting Started With Your System | 10

NOM Information (Mexico Only)

The following information is provided on the device described in this document

in compliance with the requirements of the official Mexican standards (NOM):

Importer Dell Inc. de México, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 México, D.F.

Model number

B05S

Supply voltage 100-240 V CA with 1100 W Power

Supply Unit

200-240 V CA with 1400 W Power

Supply Unit

Frequency 50/60 Hz

Current consumption

12-6.7 Amps with 1100 W Power

Supply Unit

8.6 Amps with 1400 W Power Supply

Unit

Getting Started With Your System | 11

Technical Specifications

Processor (Per System Board)

Processor type Four AMD Opteron 6100 Series processors

Or four AMD Opteron 6200 Series

processors

Or four AMD Opteron 6300 Series

processors

Expansion Bus (Per System Board)

Bus type PCI Express Generation 2

Expansion slots

PCIe One x16, low profile-MD1 (maximum length

4.795 inches)

Two x16, low profile-MD2 (maximum

length 6.674 inches)

Daughter card PCIe One x16, Mezzanine slot

Memory (Per System Board)

Architecture 32 x DDR3 1066/1333/1600 MHz RDIMM

or UDIMM

Memory module sockets 32 x DDR3 DIMM sockets

Memory module capacities 2 GB, 4 GB, 8 GB, 16 GB, or 32GB

Minimum RAM

64 GB

Maximum RAM 1024 GB

Drives

Hard drives Up to twelve 3.5-inch, hot-swappable

SAS/SATA drives or up to twenty four 2.5-

inch, hot-swappable SAS/SATA/SSD drives

NOTE: SAS hard drives are supported by

add-on card.

Getting Started With Your System | 12

Connectors (Per System Board)

Back

NIC

Two RJ-45 (10/100/1000 Mbps Ethernet)

Serial

9-pin, DTE, 16550-compatible

USB Two 4-pin, USB 2.0-compliant

Video

15-pin D-Sub VGA

Management port Dedicated Ethernet port for remote

management access

iPass connector

Connect to external PCIE devices or a PCIE

bus extender port.

Internal

Micro-SD socket

SD riser card memory socket

Video (Per System Board)

Video type

On-board AST2050 video controller

Video memory

8 MB

Power

AC power supply (per power supply)

Wattage 1023 W low line/1100 W high line

Voltage

100-240 VAC, 50-60 Hz, maximum input

current: 12.0 Amps

Heat dissipation 4217.063 BTU/hr maximum

Wattage

1400 W

Voltage 200-240 VAC, 50-60 Hz, maximum input

current: 8.6 Amps

Heat dissipation

5724 BTU/hr maximum

Maximum inrush current Initial In-rush Current cannot exceed 55

Amps (peak). Secondary In-rush Current

cannot exceed 35 Amps (peak).

Getting Started With Your System | 13

Battery (per system board)

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

3.7-V lithium ion battery pack

Physical

Height

8.76 cm (3.45 in)

Width

44.8 cm (17.6 in)

Depth 79.0 cm (31.1 in)

Weight (maximum

configuration)

42 kg (92.61 lb)

Weight (empty) 16.5 kg (36.38 lb)

Environmental

NOTE:

For additional information about environmental measurements for specific system

configurations, see

www.dell.com/environmental_datasheets

.

Temperature

Operating 10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

NOTE:

For AMD 6180SE 140W processor, the maximum

operating temperature is up to 30°C (86°F)

Storage –40° to 65°C (–40° to 149°F) with a

maximum temperature gradation of 20°C per

hour

Relative humidity

Operating 20% to 80% (noncondensing) with a

maximum humidity gradation of 10% per

hour

Storage 5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz

Storage 1.88 Grms at 10–500 Hz for 15 min

Getting Started With Your System | 14

Maximum shock

Operating One shock pulse in the positive z axis

(one pulse on each side of the system) of 31

G for 2.6 ms in the operational orientation

Storage Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of 71

G for up to 2 ms;

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of 22

G faired square wave pulse with velocity

change at 200 inches/second (508

centimeters/second)

Altitude

Operating –16 to 3,048 m (–50 to 10,000 ft)

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne contaminant level

Class

G2 or lower as defined by ISA-S71.04-1985

Dell PowerEdge

C6145

Guide de mise en route

du système

Remarques, précautions

et avertissements

REMARQUE :

une REMARQUE indique des informations importantes qui

peuvent vous aider à mieux utiliser votre ordinateur.

PRÉCAUTION : une PRÉCAUTION indique un risque d'endommagement du

matériel ou de perte de données en cas de non respect des instructions.

AVERTISSEMENT : un AVERTISSEMENT indique un risque

d'endommagement du matériel, de blessure corporelle ou de mort.

______________

Les informations contenues dans ce document sont sujettes à modification

sans préavis.

La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite

de Dell Inc. est strictement interdite.

Marques utilisées dans le présent document : Dell™, le logo DELL et PowerEdge™ sont

des marques de Dell Inc. AMD

®

est une marque déposée et AMD Opteron™ est une

marque d'Advanced Micro Devices, Inc. Red Hat Enterprise Linux

®

et Enterprise Linux

®

sont des marques déposées de Red Hat, Inc. aux États-Unis et/ou dans d'autres pays.

Novell

®

est une marque déposée et SUSE™ est une marque de Novell Inc. aux États-Unis

et dans d'autres pays. Citrix

®

et XenServer

®

sont des marques déposées ou des marques de

Citrix Systems, Inc. aux États-Unis et/ou dans d'autres pays. VMware

®

est une marque

déposée ou une marque de VMware, Inc. aux États-Unis ou dans d'autres pays.

D'autres marques et noms de marque peuvent être utilisés dans ce document pour faire

référence aux entités se réclamant de ces marques et de ces noms ou de leurs produits.

Dell Inc. rejette tout intérêt propriétaire dans les marques et les noms de marques autres

que les siens.

Modèle réglementaire B05S

Septembre 2013 N/P 6HNH8 Rév. A04

Guide de mise en route du système | 17

PRÉCAUTION : lieux à accès restreint

Ce serveur est conçu pour être installé uniquement dans des zones à accès

restreint telles que définies par la consigne Cl. 1.2.7.3 de la norme

IEC 60950-1: 2001 où les deux conditions suivantes s'appliquent:

•

Seuls peuvent avoir accès le personnel d'entretien et les utilisateurs qui

ont été informés des motifs des restrictions appliquées au lieu et des

précautions à prendre.

•

L'accès, qui se fait par l'intermédiaire d'un outil ou d'un verrou et d'une clé,

ou par d'autres moyens de sécurité, est contrôlé par le responsable en

charge du lieu.

Installation et configuration

AVERTISSEMENT : avant de commencer la procédure suivante, lisez et

respectez les consignes de sécurité fournies avec le système.

Déballage du système

Sortez le système de son emballage et identifiez chaque élément.

Installation des rails sans outils

AVERTISSEMENT : demandez toujours de l'aide avant de soulever le

système. N'essayez pas de le soulever seul, car vous risqueriez de vous

blesser.

AVERTISSEMENT : le système n'est fixé ni au rack ni aux rails. Vous

devez le soutenir correctement au cours de l'installation et du retrait pour

éviter de l'endommager ou de vous blesser.

AVERTISSEMENT : afin d'éviter un éventuel choc électrique, assurez-vous

que vous disposez d'un troisième conducteur de mise à la terre pour

l'installation du rack. L'équipement du rack doit assurer une ventilation

suffisante pour bien refroidir le système.

PRÉCAUTION : lorsque vous installez des rails dans un rack à trous

carrés, vérifiez que les taquets de fixation à tête carrée glissent bien dans

les trous carrés.

Guide de mise en route du système | 18

1

Tirez sur les boutons d'ouverture du loquet situés au milieu de l'unité

d'extrémité pour ouvrir les loquets des rails.

2

Alignez les extrémités des rails avec les montants verticaux du rack

de manière à insérer les chevilles, l'une en bas et l'autre en haut.

Faites glisser l'extrémité arrière des rails coulissants jusqu'à ce que

les loquets de verrouillage s'enclenchent.

REMARQUE : l

es rails peuvent aussi bien être utilisés dans un rack à

trous carrés (élément 1 dans la figure ci-dessous) que dans un rack à

trous ronds (élément 2 dans la figure ci-dessous).

Figure 1.

Appui sur les boutons d'ouverture des loquets

3

Répétez l'étape 1 et l'étape 2 afin de positionner et fixer les embouts

avant des rails sur les montants verticaux.

REMARQUE :

pour retirer les rails, tirez sur le bouton d'ouverture du

loquet situé au milieu de l'unité d'extrémité et dégagez chaque rail.

4

À l'arrière de chaque montant vertical du rack, insérez deux vis dans

les deux trous carrés situés juste au-dessus du rail.

5

Installez les supports de stabilisation du châssis qui vous ont été

livrés (en option) sur les collerettes du rail arrière tout en serrant

les vis.

REMARQUE :

avant de transporter des systèmes déjà installés dans le

rack, assurez-vous que les deux supports d'expédition du stabilisateur de

châssis (en option) sont en place.

Vue avan

t

Vue arrière

La page charge ...

Dell PowerEdge C6145 Guide de démarrage rapide

Dell PowerEdge C6145 Guide de démarrage rapide

dans d''autres langues

Documents connexes