Scotts CS34016S Manuel utilisateur

OWNER’S MANUAL

ELECTRIC CHAIN SAW

Model CS34016S

Your chain saw has been engineered and manufactured to our high standard for dependability, ease of

operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual

before using this product.

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY,

PART, SERVICE QUESTIONS? GO TO SCOTTS.AMERICANLAWNMOWER.COM,

OR CALL 1-800-618-7474 BETWEEN 8:00AM-5:00PM EST FOR ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

5006496

GENERAL POWER TOOL SAFETY WARNINGS

IMPORTANT SAFETY WARNINGS

2

Model CS34016S

WARNING: Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust

or fumes.

• Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces the risk

of electric shock.

Personal safety

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

• Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non

-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or

energizing power tools that have the switch on invites

accidents.

• Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

• Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

• Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewelry or long hair can be

caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

• Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

GENERAL POWER TOOL SAFETY WARNINGS

• Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Service

• Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

• When servicing a power tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual. Use of

unauthorized parts or failure to follow Maintenance

instructions may create a risk of shock or injury.

CHAIN SAW SAFETY WARNINGS

• Keep all parts of the body away from the saw chain

when the chain saw is operating. Before you start the

chain saw, make sure the saw chain is not contacting

anything. A moment of inattention while operating chain

saws may cause entanglement of your clothing or body

with the saw chain.

• Always hold the chain saw with your right hand on the

rear handle and your left hand on the front handle.

Holding the chain saw with a reversed hand configuration

increases the risk of personal injury and should never be

done.

• Hold the power tool by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring or its own cord. Saw chains contacting a live wire

may make exposed metal parts of the power tool live and

could give the operator an electric shock.

• Wear safety glasses and hearing protection. Further

protective equipment for head, hands, legs and feet is

recommended. Adequate protective clothing will reduce

personal injury by flying debris or accidental contact with

the saw chain.

• Do not operate a chain saw in a tree. Operation of a

chain saw while up in a tree may result in personal injury.

• Always keep proper footing and operate the chain saw

only when standing on fixed, secure and level surface.

Slippery or unstable surfaces such as ladders may cause a

loss of balance or control of the chain saw.

• When cutting a limb that is under tension be alert for

spring back. When the tension in the wood fibers is

released the spring loaded limb may strike the operator

and/or throw the chain saw out of control.

• Use extreme caution when cutting brush and

saplings. The slender material may catch the saw chain

and be whipped toward you or pull you off balance.

• Carry the chain saw by the front handle with the chain

saw switched off and away from your body. When

transporting or storing the chain saw always fit the

guide bar cover. Proper handling of the chain saw will

reduce the likelihood of accidental contact with the

moving saw chain.

• Follow instructions for lubricating, chain tensioning

and changing accessories. Improperly tensioned or

lubricated chain may either break or increase the chance

for kickback.

• Keep handles dry, clean, and free from oil and grease.

Greasy, oily handles are slippery causing loss of control.

• Cut wood only. Do not use chain saw for purposes

not intended. For example: do not use chain saw for

cutting plastic, masonry or non-wood building

materials. Use of the chain saw for operations different

than intended could result in a hazardous situation.

3

Model CS34016S

CHAIN SAW SAFETY WARNINGS

Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches

the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards the

operator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of

the saw which could result in serious personal injury. Do not

rely exclusively upon the safety devices built into your saw.

As a chain saw user, you should take several steps to keep

your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

It is possible to tie the extension cord and power cord in a knot

to prevent them from becoming disconnected

during use. Make the knot as shown, then con-

nect the plug end of the power cord into the re-

ceptacle end of the extension cord. This method

can also be used to tie two extension cords to-

gether.

WARNING: CALIFORNIA PROPOSITION 65 This product

contains chemicals known to the State of California to cause

cancer and birth defects or other reproductive harm.

WARNING: Some dust and debris created by this product

could contain chemicals known to the State of California to

cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

-chemicals in fertilizers

-compounds in insecticides, herbicides and pesticides

-arsenic and chromium from chemically treated lumber

Your risk from exposure to these chemicals varies, depending

on how often you do this type of work. To reduce your

exposure, work in a well ventilated area and with approved

safety equipment, such as dust masks that are specially

designed to filter out microscopic particles.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

DOUBLE INSULATION – Double Insulation is a concept in

safety in electric power tools, which eliminates the need for

the usual three-wire grounded power cord. All exposed

metal parts are isolated from the internal metal motor

components with protecting insulation. Double insulated

tools do not need to be grounded.

NOTE: The double insulated system is intended to protect

the user from shock resulting from a break in the tool’s

internal insulation. Observe all normal safety precautions to

avoid electrical shock.

POLARIZED PLUGS – To reduce the risk of electric shock,

this equipment has a polarized plug (one blade is wider than

the other). This equipment must be used with a suitable

polarized 2 wire or 3 wire extension cord. Polarized

connections will fit together only one way. Make sure that

the receptacle end of the extension cord has large and small

blade slot widths. If the plug does not fit fully into the

extension cord, reverse the plug. If it still does not fit, obtain

a suitable extension cord. If the extension cord does not fit

fully into the outlet, contact a qualified electrician to install

the proper outlet. Do not change the tool plug or extension

cord in any way.

WARNING: Use outdoor extension cords marked SW-A,

SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA.

These cords are rated for outdoor use and reduce the risk of

electric shock.

EXTENSION CORD. Make sure your extension cord is in

good condition. When using an extension cord be sure it is

heavy enough to carry the current your product will draw. An

undersized extension cord will cause a drop in line voltage

resulting in loss of power and overheating. The following

table shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt, use the

next heavier gage. The smaller the gage number, the

heavier the cord.

• Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both hands on

the saw and position your body and arm to allow you

to resist kickback forces. Kickback forces can be

controlled by the operator, if proper precautions are taken.

Do not let go of the chain saw.

• Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact and ena-

bles better control of the chain saw in unexpected situa-

tions.

• Only use replacement bars and chains specified by

the manufacturer. Incorrect replacement bars and chains

may cause chain breakage and/or kickback.

• Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to increased

kickback.

Minimum Gage for Cord Sets

Volts Total Length of cord in Feet

120V 0-25 26-50 51-100 101-150

Ampere Rating

More Not More American wire Gage

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

4

Model CS34016S

FEATURES

PRODUCT SPECIFICATIONS

CS34016S

Input……………………………….........120 Volt, 60 Hz, 13 Amp

Bar Length/Type………………...16” Oregon Bar 160SDEA041

Chain Length/Type………………16” Oregon Chain 91PX057X

Weight………………………………………………………...12 lbs

- Automatic oiling pump system - Tool-less chain tensioning system - Oil level window - Rubber over molded handle -

5

Model CS34016S

Rear Handle

Front Handle

Oil Tank Cover

Chain

Bar

Hand Guard

Cable

Lock Button

Trigger

Chain Cover

Chain Cover Knob

Tensioning Wheel

Cord Retainer

Oil Level Window

UNPACKING

This product requires no assembly.

PACKING LIST

- Chain Saw

- Blade Cover

- Instruction Manual

Carefully remove the product and any accessories from the

box. Make sure that all items listed in the packing list are

included.

Inspect the product carefully to make sure no breakage or

damage occurred during shipping. Do not discard the

packaging material until you have carefully inspected and

satisfactorily operated the product.

WARNING: If any parts are damaged or missing do not

operate this product until the parts are replaced. Failure to

heed this warning could result in serious personal injury. Call

1-800-618-7474 for assistance.

REPLACING THE GUIDE BAR AND CHAIN

DANGER: Never start the motor before installing the guide

bar, and chain. Without these parts in place, the clutch can

fly off or explode, exposing the user to possible serious injury.

WARNING: To avoid serious personal injury, read and

understand all the safety instructions provided.

DANGER: Before performing any maintenance, make sure

the tool is unplugged from the power supply. Failure to heed

this warning could result in serious personal injury.

CAUTION: Always wear gloves when handling the bar and

chain; these components are sharp and may contain burrs.

WARNING: Never touch or adjust the chain while the motor

is running. The saw chain is very sharp; always wear

protective gloves when performing maintenance to the chain

to avoid possible serious lacerations.

NOTE: When replacing the guide bar and chain, use only

identical replacement parts.

REPLACING THE SAW CHAIN

• Disconnect chain saw from power supply. Lay the chain

saw on flat surface.

• Unscrew the nut by turning the chain cover knob

counter-clockwise.

• Remove the chain cover.

• Remove the bar and chain assembly from the mounting

surface.

• Remove the old chain from the bar.

• Lay out the new saw chain in a loop and straighten any

kinks. The cutters should face in the direction of the chain

rotation. If they face backwards, turn the loop over.

ASSEMBLY

6

Model CS34016S

Chain Cover Chain Cover Knob

REPLACING THE GUIDE BAR AND CHAIN

7

Model CS34016S

• Replace the chain drive links into the bar groove.

NOTE: Make certain of the direction of chain.

• Position the chain so there is a loop at the back of the

bar.

• Hold the chain in position on the bar and place the loop

around the sprocket. Raise it to an angle of approx..45

degrees. This will make it easier to place the saw chain

onto the sprocket. It is normal that the saw chain is slack.

• Pre-tighten the chain tension by turning the tension plate

clockwise.

• Replace the chain cover. Secure by turning the chain

cover knob clockwise. Only lightly tighten the knob as you

will still need to tension the saw chain.

TENSIONING THE SAW CHAIN

• To tighten the chain, turn the tensioning wheel clockwise.

To loosen the tension, turn the tensioning wheel

counter-clockwise.

• Tighten the chain cover knob by turning it clockwise.

• Re-adjust tension of the saw chain when necessary.

The chain is correctly tensioned when there is no sag on the

underside of the guide bar, the chain is snug, but it can be

turned by hand without binding.

NOTE: If chain is too tight, it will not rotate. Loosen by turning

the tensioning wheel. Ensure that the chain will rotate without

binding.

NOTE: A new chain tends to stretch, check chain tension

frequently and tension as required.

REPLACING THE BAR

• Disconnect chain saw from power supply.

• Use a Phillips head screw driver to remove the fixing

screw. Remove the tension plate from the old bar.

• Attach the tension plate to the new bar. Make sure the

round end of the clamping plate is placed in the direction

as shown below and the clamping bolt is placed at the

bottom. Tighten the fixing screw.

• Replace the saw chain (see Saw Chain Replacement

instructions)

Clamping plate

Round

end

Clamping bolt

Fixing screw

Tension plate

OPERATING

TO TURN THE TOOL ON

Push the lock button in with your thumb and then squeeze the

trigger with your fingers. (Once the tool is running, you can release

the lock button). To turn the tool OFF, release the trigger.

WARNING: To guard against injury, observe the following:

- Read instruction manual before using, save instruction manual.

- Keep hands away from chain.

- Keep hands on handles. Don’t overreach.

A good, firm grip on the saw with both hands will help you maintain

control. Don’t let go. Grip the rear handle with your right hand

whether you are right or left handed. Wrap the fingers of your left

hand over and around the front handlebar, and your left thumb

under the front handlebar.

WARNING: Do not operate chain saw in a tree, on a ladder, or on a

scaffold; this is extremely dangerous.

CAUTION: Chain coasts after turned off.

Do not use under wet conditions.

Use extreme caution when cutting small size brush, saplings or

limbs under tension, because slender and tense material may catch

the saw and be whipped toward you, pull you off balance or spring

back.

Do not cut vines and/or small underbrush.

WARNING: Do not allow familiarity with this type of tool to make

you careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

Before you start the unit, make sure the chain saw is not contacting

any object.

WARNING: Do not cut trees near electrical wires or buildings.

Make sure you follow the instructions in maintenance for putting oil

in the chain saw.

CAUTION: Failure to lubricate the chain will cause damage to the

bar and chain. Use only a good quality bar and chain oil or, if not

available, unused SAE 30 weight motor oil may be substituted. One

minute of use will consume approx. 0.2 fl. oz. (6ml) of oil.

NOTE: It is normal for oil to seep from the saw when not in use. To

prevent seepage, empty the oil tank after each use. When storing

the unit for a long period of time (3 months or longer) be sure the

chain is lightly lubricated; this will prevent rust on the chain and bar

sprocket.

WARNING: Kickback may occur when the moving chain contacts

an object at the upper portion of the tip of the guide bar or when the

wood closes in and pinches the chain saw in the cut. Contact at the

upper portion of the tip of the guide bar can cause the chain to dig

into the object and stop the chain for an instant. The result is a

lightening fast, reverse reaction which kicks the guide bar up and

back toward the operator. If the chain saw is pinched along the top

of the guide bar, the guide bar can be driven rapidly back toward

the operator. Either of these reactions can cause loss of saw

control which can result in serious injury. Do not rely exclusively

upon the safety devices built into the saw. As a chain saw user, you

should take several steps to keep your cutting jobs free from

accident or injury.

WARNING: Do Not use the chain saw with any type of accessory

or attachment. Such usage might be hazardous.

The following precautions should be followed to minimize

kickback:

1. Always grip the saw firmly with both hands. Hold the saw

firmly with both hands when the unit is running. Place your

right hand on the rear handle and your left hand on the front

handle with your thumbs and fingers encircling the chain

saw handles. A firm grip together with a stiff left arm will help

you maintain control of the saw if kickback occurs.

2. Make sure that the area in which you are cutting is free from

obstructions. Do not let the nose of the guide bar contact a

log, branch, fence or any other obstruction that could be hit

while you are operating the saw.

3. Always cut with the unit running at full speed. Fully squeeze

the throttle trigger and maintain a steady cutting speed.

Push and Pull – This reaction force is always opposite to the

direction the chain is moving where wood contact is made. Thus,

the operator must be ready to control the PULL when cutting on

the bottom edge of the bar, and PUSH when cutting along the top

edge.

Wear non-slip gloves for maximum grip and protection.

Proper Cutting Stance

Weight should be balanced with both feet on solid ground.

Keep left arm with elbow locked in a “straight arm” position to

withstand any kickback force.

Your body should always be to the left of the chain line.

Basic Cutting Procedure

Small trees up to 6-7inches in diameter are usually cut in a single

cut. Large trees require notch cuts. Notch cuts determine the

direction the tree will fall.

WARNING: If the tree starts to fall in the wrong direction, or if the

saw gets caught or hung up during the fall, leave the saw and

save yourself.

WARNING: Periodically glance at the top of the tree during the

back-cut to assure the tree is going to fall in the desired direction.

Practice cutting a few small logs using the following technique to

get the “feel” of using the saw before you begin a major sawing

operation.

Take the proper stance in front of the wood with the saw off.

Squeeze the trigger and let the chain accelerate to full speed

before entering the cut.

Hold the saw firmly with both hands. Always keep your left hand

on the front handle and your right hand on the rear handle so that

your body is to the left of the chain line.

8

Model CS34016S

OPERATING

Keep the unit running the entire time you are cutting, maintain

a steady speed.

Allow the chain to cut for you; exert only light downward

pressure. If you force the cut, damage to the bar, chain, or

unit can result.

Do not put pressure on the saw at the end of the cut.

When felling a tree, keep everyone a safe distance from the

cutting area. During felling operations, the safe distance

should be at least twice the height of the largest trees in the

felling area. If the tree makes contact with any utility line, the

utility company should be notified immediately.

Always cut with both feet on solid ground to prevent being

pulled off balance.

Do not cut above chest height, as a saw held higher is difficult

to control against kickback forces.

FELLING A TREE

When bucking and felling operations are being performed by

two or more persons, at the same time, the felling operation

should be separated from the bucking operation by a distance

of at least twice the height of the tree being felled. Trees

should not be felled in a manner that would endanger any

person, strike any utility line or cause any property damage. If

the tree does make contact with any utility line, the utility

company should be notified immediately.

WARNING: Check the tree for damaged or dead branches

that could fall and hit you during felling.

Before any cuts are started, pick your escape route (or routes

in case the intended route is blocked); clear the immediate

area around the tree and make sure there are no obstructions

in your planned path of retreat. A clear path of safe retreat is

approximately 135 degrees from planned line of fall. The

retreat path should extend back and diagonally to the rear of

the expected line of fall.

Before felling is started, consider the force and direction of

the wind, the lean and balance of the tree, and the location of

large limbs. These things influence the direction in which the

tree will fall. Do not try to fell a tree along a line different from

its natural line of fall.

The chain saw operator should keep on the uphill side of the

terrain as the tree is likely to roll or slide downhill after it is

felled.

Remove dirt, stones, loose bark, nails, staples, and wire from

the tree where felling cuts are to be made.

NOTCHED UNDERCUT – Cut a notch about 1/3 diameter of

the tree, perpendicular to the direction of the fall. Make the

cuts of the notch so they intersect at a right angle to the line

of fall. This notch should be cleaned out to leave a straight

line. To keep the weight of the wood off the saw, always

make the lower cut of the notch before the upper cut.

WARNING: Do not fell trees during periods of high wind or

heavy precipitation. Wait to do your cutting until the hazard

has ended.

WARNING: Do not cut down trees having an extreme lean or

large trees that have rotten limbs, loose bark, or hollow

trunks. Have these trees pushed or dragged down with heavy

equipment, then cut them up.

FELLING BACK-CUT

The back-cut is always made level and horizontal, and at a

minimum of 2 inches (5cm) above the horizontal cut of the

notch.

Never cut through to the notch. Always leave a band of wood

between the notch and back-cut (approximately 2 inches

(5cm) or 1/10 the diameter of the tree). This is called “hinge”

or “hinge wood.” It controls the fall of the tree and prevents

slipping or twisting or shoot-back of the tree off the stump.

On large diameter trees, stop the back cut before it is deep

enough for the tree to either fall or settle back on the stump.

Then insert soft wooden or plastic wedges into the cut so they

do not touch the chain. The wedges can be driven in, little by

little, to help jack the tree over.

9

Model CS34016S

OPERATING

CUTTING INSTRUCTIONS

LIMBING

Limbing is removing branches from a fallen tree.

Work slowly, keeping both hands on the chain saw with a firm grip.

Always make sure your footing is secure and your weight is distributed

evenly on both feet.

Leave the larger support limbs under the tree to keep the tree off the

ground while cutting.

Limbs should be cut one at a time. Remove the cut limbs from the work

area often to help keep the work area clean and safe.

Branches under tension should be cut from the bottom up to avoid

binding the chain saw.

Keep the tree between you and the chain saw while limbing. Cut from

the side of the tree opposite the branch you are cutting.

WARNING: Never climb into a tree to limb or prune. Do not stand on

ladders, platforms, a log, or in any position which can cause you to

lose your balance or control of the saw.

PRUNING

Pruning is trimming limbs from a live tree.

Work slowly, keeping both hands on the chain saw with a firm grip.

Always make sure your footing is secure and your weight is distributed

evenly on both feet.

When pruning trees it is important not to make the finishing cut next to

the main limb or trunk until you have cut off the limb further out to

reduce the weight. This prevents stripping the bark from the main

member.

Under-buck the branch 1/3 through for your first cut. Your second cut

should over-buck to drop the branch off. Now make your finishing cut

smoothly and neatly against the main member so the bark will grow

back to seal the wound.

WARNING: SPRINGPOLES

A springpole is any log, branch, rooted stump, or sapling which is bent

under tension by other wood so that it springs back if the wood holding

it is cut or removed. On a fallen tree, a rooted stump has a high

potential of springing back to the upright position during the bucking cut

to separate the log from the stump. Watch out for springpoles, they are

dangerous. They could result in severe or fatal injury.

As the tree starts to fall, stop the chain saw and put it down

immediately. Retreat along the cleared path, but watch the action in

case something falls your way. Be alert for overhead limbs or

branches that may fall and watch your footing.

WARNING: Never cut through to the notch when making a back-cut.

The hinge controls the fall of the tree, this is a section of wood

between the notch and back-cut.

BUCKING

Bucking is the term used for cutting a fallen tree to the desired log

length.

Always make sure your footing is secure and your weight is

distributed evenly on both feet.

Cut only one log at a time. Support small logs on a saw horse or

another log while bucking.

Keep a clear cutting area. Make sure that no objects can contact the

guide bar nose and chain during cutting, this can cause kickback.

When bucking on a slope, always stand on the uphill side of the log.

To maintain complete control of the chain saw when cutting through

the log, release the cutting pressure near the end of the cut without

relaxing your grip on the chain saw handles. Do not let the chain

contact the ground. After completing the cut, wait for the saw chain

to stop before you move the chain saw. Always stop the motor

before moving from tree to tree.

BUCKING LOGS UNDER STRESS

When the log is supported along its entire length, it should be cut

from the top or over-bucking.

When the log is supported on one end, cut 1/3 diameter from the

underside or under-bucking. Then make the finishing cut by

over-bucking to meet the first cut.

As the log is being cut, it will tend to bend. The saw can become

pinched or hung in the log if you make the first cut deeper than 1/3

of the diameter of the log.

Give special attention to logs under stress to prevent the bar and

chain from pinching.

OVERBUCKING – Begin on the top

side of the log with the bottom of the

saw against the log; exert light pressure

downward. Note that the saw will tend

to pull away from you.

UNDER-BUCKING – Begin on the

under side of the log with the top of the

saw against the log; exert light pressure

upward. During under-bucking, the

saw will tend to push back at you. Be

prepared for this reaction and hold the

saw firmly to maintain control.

10

Model CS34016S

UNDERBUCKING

CUT LIMBS ONE AT A TIME AND LEAVE

SUPPORT LIMBS UNDER TREE UNTIL

LOG IS CUT

LOAD

SECOND CUT

FIRST CUT

1/3 DIA.

FINISHING CUT

NOTCH

BACK CUT

HINGE

OVERBUCKING

CHAIN TENSION AND MAINTENANCE

CHAIN TENSION

Stop the engine before setting the chain tension. Make sure the guide

bar screw is loosened to finger tight, turn the tensioning wheel up or

down to tension the chain. A cold chain will be correctly tensioned

when there is no slack on the underside of the guide bar, the chain is

snug, but it can be turned by hand without binding.

Chain must be re-tensioned whenever the flats on the drive links hang

out of the bar groove.

During normal saw operation, the

temperature of the chain will

increase. The drive links of a

correctly tensioned warm chain will

hang approximately .050 in.

(1.25mm) out of the bar groove. Be

aware that chain tensioned while

warm, may be too tight upon

cooling. Check the “cold tension”

before next use.

NOTE: A new chain tends to stretch, check chain tension frequently

and tension as required.

CHAIN MAINTENANCE

CAUTION: Disconnect from the power supply and make sure the

chain has stopped before you do any work on the saw.

For smooth and fast cutting, chain needs to be maintained properly.

The chain requires sharpening when the wood chips are small and

powdery, the chain must be forced through the wood during cutting,

or the chain cuts to one side. During maintenance of your chain

remember:

- Improper filing angle of the side plate can increase the risk of

severe kickback.

- Raker (depth gauge) clearance.

- Too low increases the potential for kickback.

- Not low enough decreases cutting ability.

- If cutter teeth have hit hard objects such as nails and stones, or

have been abraded by mud or sand on the wood, have service dealer

sharpen chain.

NOTE: Inspect the drive sprocket for wear or damage when replacing

the chain. If signs of wear or damage are present in the areas indicat-

ed, have the drive sprocket replaced by a qualified individual. Call our

customer service help line at 1-800-618-7474 for assistance.

HOW TO SHARPEN THE CUTTERS

Be careful to file all cutters to the

specified angles and to the same

length, as fast cutting can be

obtained only when all cutters are

uniform.

Wear gloves for protection.

Properly tension the chain prior to

sharpening. Refer to “Chain

Tension Section” earlier in this manual. Do all of your filing at the

midpoint of the bar.

Use a 5/32 in. diameter round file and holder.

Keep the file level with the top

plate of the tooth. Do not let the

file dip or rock. Using light but

firm pressure, stroke towards

the front corner of the tooth.

Lift file away from the steel on each return stroke.

Put a few firm strokes on

every tooth. File all left hand

cutters in one direction.

Then move to the other side

and file the right hand

cutters in the opposite

direction. Occasionally

remove filing from the file

with a wire brush.

WARNING: Improper chain sharpening increases the potential of kick-

back.

WARNING: Failure to replace or repair damaged chain can cause seri-

ous injury.

WARNING: The saw chain is very sharp, always wear protective gloves

when performing maintenance to the chain.

TOP PLATE FILING ANGLE

Correct 30 degrees – File holders

are marked with guide marks to

align file properly to produce top

plate angle.

Less than 30 degrees – for cross

cutting.

More than 30 degrees – feathered edge dulls quickly.

SIDE PLATE ANGLE

Correct – 80 degrees produced

automatically if correct diameter

file is used in file holder.

Hook – “Grabs” and dulls quickly. Increases potential of kickback.

Results from using a file with a diameter too small, or file held too low.

Backward Slope – Needs too much feed pressure, causes excessive

wear to bar and chain. Results from using a file with a diameter too

large, or file held too high.

DEPTH GAUGE CLEARANCE

The depth gauge should be main-

tained at a clearance of .025 in. (0.6

mm). Use a depth gauge tool for

checking the depth gauge clearances.

Every time the chain is filed, check the

depth gauge clearance

Use a flat file and a depth gauge

jointer to lower all gauges uniformly.

Depth gauge jointers are available

in .020 in. to .035 in. (0.5 mm to 0.9

mm). Use a .025 in. (0.6 mm) depth

gauge jointer. After lowering each

depth gauge, restore original shape

by rounding the front. Be careful not to

damage adjoining drive links with the

edge of the file.

Depth gauges must be adjusted with the flat file in the same direction

the adjoining cutter was filed with the round file. Use care not to contact

cutter face with flat file when adjusting depth gauges.

Approx. .050 (1.25mm)

11

Model CS34016S

MAINTENANCE

If you drop the chain saw, carefully inspect it for damage. If the

blade is bent, housing cracked, or handles broken or if you see

any other condition that may affect the saw’s operation, call our

customer service line at 1-800-618-7474 for assistance.

Make sure the unit is disconnected from the power supply, then

use only mild soap and a damp cloth to clean the tool. Never let

any liquid get inside the tool; never immerse any part of the tool

into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment should be performed by a

qualified individual always using identical replacement parts.

CAUTION: Do not at any time let brake fluids, gasoline, petroleum

based products, penetrating oils, etc., come in contact with plastic

parts. They contain chemicals that can damage, weaken or

destroy plastic.

Ensure that the plastic bar cover is in place when storing.

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals Do not store the tool on

or adjacent to fertilizers or chemicals.

For smooth and fast cutting, chain needs to be maintained

properly. The chain requires sharpening when the wood chips are

small and powdery, the chain must be forced through the wood

during cutting, or the chain cuts to one side. Refer to instructions

earlier in this manual for instructions on properly sharpening the

chain.

TROUBLESHOOTING

Possible Cause

- Extension cord not connected to the plug

- Cord not connected to power source

- Lock off button not fully depressed

Possible Solution

- Check extension cord is fully connected to tool

- Check extension cord is fully connected to a live receptacle

- Check that lock off is fully depressed prior to engaging trigger

switch

- Bar and chain running hot and

smoking

- Check tension for over-tight condition

- Chain oil tank empty

- Chain installed in wrong direction

- Adjust chain tension

- Fill tank with chain oil

- Reverse chain so that cutters face the right direction

- Chain tension too tight

- Check guide bar and chain for damage

- Motor runs but chain is not rotating - Adjust chain tension

- Replace damaged bar and chain with identical replacement

parts or contact our customer service center at 1-800-618-7474

for assistance.

LUBRICATION SYSTEM

BEFORE USING : Fill oil well with new quality bar and chain oil, or

if unavailable, unused SAE 30 weight motor oil may be substituted.

The chain is automatically lubricated.

Use only new bar and chain oil or unused SAE 30 weight motor oil

may be substituted. Never use wasted oil, low quality oil, or insufficient

oil. This could damage the pump; the bar and the chain which may

result in serious personal injury. Check oil level before each work

session, refill if less than ¼ full.

If the lubrication system does not work properly, check if the oil filter and

all oil-ways are clean and free from obstructions. If it is still not working,

call our customer service line at 1-800-618-7474 for assistance.

GUIDE BAR MAINTENANCE

When the guide bar shows signs of wear, reverse it on the saw to

distribute the wear for maximum bar life. The bar should be cleaned

every day of use and checked for wear and damage.

Feathering or burring of the bar rails is a normal process of bar wear.

Such faults should be smoothed with a file as soon as they occur.

A bar with any of the following faults should be replaced.

- Wear inside the bar rails which permits the chain to lay over sideways.

- Bent guide bar

- Cracked or broken rails

- Spread rails

In addition, guide bars with a sprocket at their tip must be lubricated

weekly with a grease syringe to extend the guide bar life. Using a

grease syringe, lubricate weekly in the lubricating hole.

Turn the guide bar and check that the lubrication holes and chain

groove are free from obstructions.

Problem

- Unit does not run

12

Model CS34016S

13

Model CS34016S

PARTS AND SERVICE

For parts or service, please call 1-800-618-7474 or visit us online at scotts.americanlawnmower.com.

Be sure to provide all relevant information when you call or visit.

REPAIR PARTS (KITS/ ITEMS)

The model/ serial number of this tool is found on a plate or label attached to the housing. Please

record the serial number in the space provided below.

MODEL NUMBER CS34016S____

SERIAL NUMBER________________

Always mention the model number when ordering kits/items for this tool.

No. Kit/Item Number Description QTY

1

CS34-SCA-1 Sprocket cover assembly kit

1

2

CS34-BCK-1 16" Bar & chain assembly kit

1

3

CS34-OTC-1 Oil cap assembly

1

CALL US FIRST !!

Call us first with questions about operating or maintaining your tool

at 1-800-618-7474 between 8:00 a.m. – 5:00 p.m. Eastern

Standard Time, or get assistance on scotts.americanlawnmower.com.

American Lawn Mower Company

The Great States Corporation

7444 Shadeland Station Way

Indianapolis, IN 46256 USA

Phone 1-800-618-7474

scotts.americanlawnmower.com

In a continued commitment to improve quality, the Manufacturer reserves the right

to make component changes or design changes when necessary.

Rev. 11/08/18

OWNER’S MANUAL

CS34016S ELECTRIC CHAIN SAW

WARRANTY POLICY

Scotts Warranty policy

• 3 Year limited warranty on all Scotts corded power tools from date of purchase when used for personal, household, or family use.

The Great States Corp. (GSC) warrants to the original owner that this Scotts product and service part is free from defects in materials and

workmanship and agrees to repair or replace any defective product or part for the warranty period as stated above.

• Warranty voided if used for commercial or industrial purposes or any other improper use as determined by GSC.

• Warranty does not include repairs necessary due to operator’s abuse or negligence (including overloading the product beyond capacity

or immersion in water), or the failure to assemble, operate, maintain or store the product according to the instructions in the owner’s

manual.

• This warranty does not cover

 Wear items, including but not limited to - drive belts & gears, tines, cutting blades, mower blades, saw chains, mulching blades,

blower fans, spool covers, trimmer line, blower and vacuum tubes, guide bars, high pressure hoses, wheels, handles, augers, worn

bags, power cables, and other items subject to wear over time.

 Wear on batteries, including but not limited to – drops, wear and breakage on charger, exposure to extreme temperature swings

(hot or cold), battery left on charger too long, battery left uncharged for too long, and misuse or abuse of the battery.

• This warranty does not cover damage caused by cold, heat, rain, excessive humidity or other environmental extremes.

• This warranty does not cover normal deterioration of the exterior finish or normal wear and tear on the products including, but not limited

to scratches, cracks, dents, or damage caused by outside chemicals.

• This warranty is not transferable and only applies to new products sold directly from an authorized retailer. This warranty does not apply

to any product, new or used, purchased through unauthorized third-party channels. For information on authorized dealers, contact our

customer support hotline at 1-800-618-7474 (Mon-Fri 8am-5pm Est)

• Any incidental, indirect or consequential loss, damage, or expense that may result from any defect or malfunction of the products is not

covered by the warranty.

• The warranty does not include installation, assembly or normal adjustments explained in the operator’s manual. The expense of

delivering the product to the vendor and the expense of returning the product or replacement parts to the owner is not covered by the

warranty.

Additional Warranty Limitations

Some states do not allow the exclusion or limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

Products sold damaged or incomplete, sold ―as is, or sold as reconditioned are not covered under the warranty.

Damage or liability caused by shipping, improper handling, improper assembly, incorrect voltage, improper wiring, improper maintenance,

improper modification or the use of accessories and/or attachments not specifically recommended is not covered by this warranty.

Proof of purchase, original dated sales receipt, must accompany all warranty claims.

For claims go to scotts.americanlawnmower.com or call our customer support hotline from 8am-5pm EST,

Mon-Fri at 1-800-618-7474

MANUAL DEL OPERARIO

MOTOSIERRA ELÉCTRICA

Modelo CS34016S

Este producto ha sido diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación

y seguridad para el operario. Si se trata con cuidado, esta herramienta le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender el manual del

operario antes de usar este producto.

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

Muchas gracias por su compra.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE

FUNCIONAMIENTO, MONTAJE, PIEZAS O SERVICIO TÉCNICO? VAYA A

SCOTTS.AMERICANLAWNMOWER.COM, O LLAME AL 1-800-618-7474 ENTRE LAS 8:00 Y LAS

17:00 HORA DEL ESTE DE LOS ESTADOS UNIDOS.

5006496

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

2

Modelo CS34016S

ADVERTENCIA: Lea todas las advertencias de seguridad y las

instrucciones. La inobservancia de las advertencias e instrucciones

puede causar descargas eléctricas, incendios o lesiones graves.

Guarde todas las advertencias e instrucciones para consultarlas

en el futuro. El término “herramienta eléctrica” en las advertencias se

refiere a las herramientas eléctricas que funcionan con corriente (con

cordón) o las que funcionan con batería (inalámbricas).

Área de trabajo

• Mantenga limpia y bien iluminada el área de trabajo. Un área

de trabajo mal despejada o mal iluminada propicia accidentes.

• No utilice herramientas motorizadas en atmósferas

explosivas, como las existentes alrededor de líquidos, gases

y polvos inflamables. Las herramientas eléctricas generan

chispas que pueden encender el polvo y los vapores inflamables.

• Mantenga alejados a los niños y circunstantes al maniobrar

una herramienta eléctrica. Toda distracción puede causar la

pérdida del control de la herramienta.

Seguridad eléctrica

• Las clavijas de las herramientas eléctricas deben

corresponder a las tomas de corriente donde se conectan.

Nunca modifique la clavija de ninguna forma. No utilice

ninguna clavija adaptadora con herramientas eléctricas

dotadas de contacto a tierra. Conectando las clavijas

originales en las tomas de corriente donde corresponden se

disminuye el riesgo de una descarga eléctrica.

• Evite el contacto del cuerpo con las superficies de objetos

conectados a tierra, como las tuberías, radiadores, estufas y

refrigeradores. Existe un mayor riesgo de descargas eléctricas

si el cuerpo está haciendo tierra.

• No exponga las herramientas eléctricas a la lluvia ni a

condiciones de humedad. La introducción de agua en una

herramienta eléctrica aumenta el riesgo de descargas eléctricas.

• No maltrate el cordón eléctrico. Nunca utilice el cordón para

trasladar, desconectar o tirar de la herramienta eléctrica.

Mantenga el cordón lejos del calor, aceite, bordes afilados y

piezas móviles. Los cordones eléctricos dañados o enredados

aumentan el riesgo de descargas eléctricas.

• Al utilizar una herramienta eléctrica a la intemperie, use un

cordón de extensión apropiado para el exterior. Usando un

cordón adecuado para el exterior se disminuye el riesgo de

descargas eléctricas.

• Si debe operar una herramienta en lugares húmedos, use un

suministro protegido por un interruptor de circuito con

pérdida a tierra (GFCI). El uso de un GFCI reduce el riesgo de

descargas eléctricas.

ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTAS ELÉCTRICAS

Seguridad personal

• Permanezca alerta, preste atención a lo que esté haciendo

y aplique el sentido común al utilizar herramientas

eléctricas. No utilice la herramienta eléctrica si está

cansado o se encuentra bajo los efectos de alguna droga,

alcohol o medicamento. Un momento de inatención al

utilizar una herramienta eléctrica puede causar lesiones

corporales serias.

• Utilice protección el equipo otros. Siempre póngase

protección ocular. El uso de equipo protector como

mascarilla para el polvo, calzado de seguridad, casco y

protección para los oídos en las circunstancias donde

corresponda disminuye el riesgo de lesiones.

• Evite que la herramienta se active accidentalmente.

Asegúrese de que el interruptor esté en la posición de

apagado antes de conectar la herramienta a un suministro

de corriente o de colocar un paquete de baterías.

Transportar herramientas eléctricas con el dedo en el

interruptor o enchufar herramientas eléctricas que tienen el

interruptor encendido puede ocasionar accidentes.

• Retire toda llave o herramienta de ajuste antes de encender

la herramienta eléctrica. Toda llave o herramienta de ajuste

dejada en una pieza giratoria de la herramienta eléctrica puede

causar lesiones.

• No estire el cuerpo para alcanzar mayor distancia.

Mantenga una postura firme y buen equilibrio en todo

momento. De esta manera se logra un mejor control de la

herramienta eléctrica en situaciones inesperadas.

• Vístase adecuadamente. No vista ropas holgadas ni joyas.

Mantenga el cabello, la ropa y los guantes alejados de las

piezas móviles. Las ropas holgadas y las joyas, así como el

cabello largo, pueden engancharse en las piezas móviles.

• Si se suministran dispositivos para conectar mangueras de

extracción y captación de polvo, asegúrese de que éstas

estén bien conectadas y se usen correctamente. El uso de

la captación de polvo puede reducir los peligros relacionados

con éste.

Empleo y cuidado de la herramienta eléctrica

• No fuerce la herramienta eléctrica. Utilice la herramienta

eléctrica adecuada para cada trabajo. La herramienta

eléctrica adecuada efectúa mejor y de manera más segura el

trabajo, si además se maneja a la velocidad para la que está

diseñada.

• No utilice la herramienta si el interruptor no enciende o no

apaga. Cualquier herramienta eléctrica que no pueda

controlarse con el interruptor es peligrosa y debe repararse.

3

Modelo CS34016S

ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTAS ELÉCTRICAS

• Desconecte la clavija del suministro de corriente o retire el

paquete de baterías de la herramienta eléctrica, según sea el

caso, antes de efectuarle cualquier ajuste, cambiarle

accesorios o guardarla. Tales medidas preventivas de

seguridad reducen el riesgo de poner en marcha accidentalmente

la herramienta.

• Guarde las herramientas eléctricas desocupadas fuera del

alcance de los niños y no permita que las utilicen personas

no familiarizadas con las mismas o con estas instrucciones.

Las herramientas eléctricas son peligrosas en manos de personas

no capacitadas en el uso de las mismas.

• Preste servicio a las herramientas eléctricas. Revise para ver

si hay desalineación o atoramiento de piezas móviles, ruptura

de piezas o cualquier otra condición que pueda afectar el

funcionamiento de la herramienta. Si está dañada la

herramienta eléctrica, permita que la reparen antes de usarla.

Numerosos accidentes son causados por herramientas eléctricas

mal cuidadas.

• Mantenga las herramientas de corte afiladas y limpias. Las

herramientas de corte bien cuidadas y con bordes bien afilados,

tienen menos probabilidad de atascarse en la pieza de trabajo y

son más fáciles de controlar.

• Utilice la herramienta eléctrica, los accesorios y brocas,

hojas y cuchillas de corte, ruedas de esmeril, etc. de

conformidad con estas instrucciones, tomando en cuenta

las condiciones de trabajo y la tarea por realizar. Si se

utiliza la herramienta eléctrica para operaciones diferentes de

las indicadas podría originar una situación peligrosa.

Servicio

• Permita que un técnico de reparación calificado preste

servicio a la herramienta eléctrica, y sólo con piezas de

repuesto idénticas. De esta manera se mantiene la seguridad

de la herramienta eléctrica.

• Al dar servicio a una herramienta eléctrica, sólo utilice

piezas de repuesto idénticas. Siga las instrucciones

señaladas en la sección Mantenimiento de este manual. El

empleo de piezas no autorizadas o el incumplimiento de las

instrucciones de mantenimiento puede significar un riesgo de

descarga eléctrica o de lesiones.

ADVERTENCIAS DE SEGURIDAD DE LA MOTOSIERRA

• Mantenga todas las partes del cuerpo alejadas de la

motosierra mientras esté en funcionamiento. Antes de

encender la motosierra, asegúrese de que no esté en

contacto con nada. Un momento de distracción mientras usa la

motosierra puede hacer que la motosierra agarre su ropa o una

parte de su cuerpo.

• Siempre sostenga la motosierra con la mano derecha en el

mango trasero y la mano izquierda en el mango delantero.

Sostener la motosierra con las manos invertidas aumenta el riesgo

de sufrir lesiones personales y siempre debe evitarse.

• Sostenga la herramienta eléctrica únicamente por las partes

aisladas, porque la misma podría morder cables ocultos. Si la

motosierra toca un cable vivo, las piezas metálicas de la

herramienta podrían energizarse y producirle una descarga

eléctrica al operador.

• Use gafas de seguridad y protección auditiva. También se

recomienda usar equipo de protección para la cabeza, las

manos, las piernas y los pies. La indumentaria de protección

adecuada reducirá las lesiones personales en caso de que salgan

partículas despedidas o su cuerpo toque accidentalmente la

motosierra.

• No use la motosierra sobre un árbol. Si usa la motosierra

subido a un árbol, podría sufrir lesiones personales.

• Siempre mantenga un buen apoyo y utilice la motosierra

únicamente sobre superficies fijas, firmes y niveladas. Las

superficies resbaladizas o inestables como las escaleras pueden

hacerle perder el equilibrio o el control de la motosierra.

• Cuando corte una rama que esté sometida a tensión, esté

atento al retorno. Cuando se libera la tensión de las fibras de

madera, la rama podría golpear al operador o lanzar la

motosierra en forma descontrolada.

• Tenga extremo cuidado al cortar maleza o retoños. El

material delgado podría quedar atrapado en la motosierra y

salir disparado hacia usted o hacerle perder el equilibrio.

• Transporte la motosierra apagada, lejos de su cuerpo y

tomada del mango frontal. Siempre que transporte o

almacene la motosierra, coloque la cubierta de la barra

guía. Manipular la motosierra correctamente reduce la

probabilidad de tocar accidentalmente la cadena en

movimiento.

• Siga las instrucciones para lubricar la herramienta,

tensionar la cadena y cambiar los accesorios. Si la cadena

no está correctamente tensionada o lubricada, podría

romperse o presentar un mayor riesgo de que ocurra un

contragolpe.

• Mantenga los mangos secos, limpios y sin aceite ni grasa.

Los mangos con aceite o grasa son resbaladizos y pueden

hacerle perder el control.

• Corte únicamente madera. No use la motosierra para usos

distintos de los previstos. Por ejemplo: no use la

motosierra para cortar plástico, mampostería ni materiales

de construcción que no sean de madera. El uso de la

motosierra para fines distintos de los previstos podría dar lugar

a una situación de riesgo.

4

Modelo CS34016S

ADVERTENCIAS DE SEGURIDAD DE LA MOTOSIERRA

Causas y prevención del contragolpe:

Puede ocurrir un contragolpe cuando la punta de la barra guía toca

un objeto o cuando la madera se cierra y pellizca la cadena de la

sierra en el punto de corte.

En algunos casos, el contacto de la pieza de trabajo con la punta de

la barra guía puede causar una reacción súbita en dirección inversa,

la cual lanza la barra guía hacia arriba y hacia atrás, en dirección al

operador.

El pellizcamiento de la cadena de la sierra en la parte superior de la

barra guía puede empujar la barra rápidamente hacia atrás, en

dirección al operador.

Cualquiera de estas dos reacciones puede causar la pérdida del

control de la sierra, lo cual a su vez puede producir lesiones

personales serias. No dependa exclusivamente de los dispositivos de

seguridad incorporados de la sierra. Como usuario de una

motosierra, debe tomar varias medidas para evitar los accidentes y

las lesiones en todos sus trabajos de corte.

El contragolpe es el resultado de un uso indebido de la herramienta o

de procedimientos o condiciones de utilización incorrectos, y se

puede evitar tomando las precauciones apropiadas que se presentan

a continuación:

• Mantenga la herramienta bien sujeta, con los pulgares y los

dedos alrededor de los mangos de la motosierra; sostenga la

herramienta con ambas manos y posicione su cuerpo y su

brazo de una forma que le permita resistir la fuerza de un

contragolpe. El operador puede controlar las fuerzas del

contragolpe si toma las precauciones adecuadas. No suelte la

motosierra.

• No se estire ni corte por encima de la altura del hombro. Esto

ayuda a evitar el contacto accidental con la punta y permite un

mejor control de la motosierra ante situaciones inesperadas.

• Use únicamente barras y cadenas de repuesto indicadas por

el fabricante. El uso de barras y cadenas de repuesto incorrectas

podría hacer que la cadena se rompa o que se produzcan

contragolpes.

• Siga las instrucciones de afilado y mantenimiento de la

cadena de la sierra que provee el fabricante. Disminuir la altura

del calibrador de profundidad puede aumentar la probabilidad de

que ocurra un contragolpe.

DOBLE AISLAMIENTO. El doble aislamiento es un concepto de

seguridad en las herramientas eléctricas que elimina la necesidad del

acostumbrado cable de alimentación puesto a tierra mediante el

sistema de tres cables. Todas las piezas metálicas expuestas están

separadas de los componentes del motor metálico interno por un

aislamiento protector. Las herramientas con doble aislamiento no

necesitan la conexión a tierra.

NOTA: La finalidad del sistema de doble aislamiento es proteger al

usuario de una descarga eléctrica provocada por una rotura del

aislamiento interno de la herramienta. Respete todas las

precauciones generales de seguridad para evitar una descarga

eléctrica.

ENCHUFES POLARIZADOS. Para reducir el riesgo de una descarga

eléctrica, este equipo tiene un enchufe polarizado (un contacto es

más ancho que el otro). Se debe utilizar un cable de extensión

polarizado adecuado de dos o tres cables. Las conexiones

polarizadas encajan de una sola manera. Cerciórese de que el

extremo del receptáculo del cable de extensión tenga ranuras de

anchos diferentes para los contactos. Invierta el enchufe si no encaja

exactamente en el cable de extensión. Si aún así no encaja, consiga

un cable de extensión adecuado. Si el cable de extensión no se

adapta bien al tomacorriente, llame a un electricista competente para

que instale un tomacorriente adecuado. No modifique el enchufe de

la herramienta ni el cable de extensión de ningún modo.

ADVERTENCIA: Use cables de extensión para exteriores

rotulados con las siguientes inscripciones: SW-A, SOW-A, STW-A,

STOW-A, SJW-A, SJTW-A, o SJTOWA. Estos cables están

especificados para usar al aire libre y reducir el riesgo de descarga

eléctrica.

CABLE DE EXTENSIÓN. Asegúrese de que el cable de extensión

esté en buenas condiciones. Además, compruebe que tenga el

grosor suficiente para transportar la corriente que necesitará el

producto. Un cable de extensión muy pequeño provocará una

disminución en la tensión de la línea y, como resultado, una pérdida

de potencia y recalentamiento. La siguiente tabla muestra el tamaño

correcto que se debe usar según la longitud del cable y el amperaje

de la etiqueta. Ante la duda, utilice el siguiente calibre más grueso.

Cuanto más bajo es el número de calibre, más grueso es el cable.

El cable de extensión y el cable de alimentación se pueden atar para

evitar que se desconecten durante el uso. Realice el

nudo como se muestra en la imagen y después conecte

el enchufe del cable de alimentación en el receptáculo

del cable de extensión. Este método también se puede

aplicar para unir dos cables de extensión.

ADVERTENCIA: Proposición 65 de California: Este product contiene

sustancias químicas al estado de california como causantes de cáncer,

defectos de nacimiento u otros problemas reproductivos.

ADVERTENCIA: Parte del polvo generado por este product contiene

químicos reconocidos por el Estado de California como causantes de

cáncer, defectos de nacimiento u otros efectos nocivos para el aparato

reproductor. Algunos ejemplos de estos productos químicos son:

- compuestos presentes en fertilizantes;

- compuestos presentes en insecticidas, herbicidas y pesticidas; y

- arsénico y cromo de maderas tratadas químicamente.

Para reducir la exposición a estos químicos, use equipo de protección

aprobado, como mascarillas antipolvo especialmente elaboradas para

eliminar partículas microscópicas mediante un proceso de filtrado.

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

Calibre mínimo para los cables

Voltios Longitud del cable en pies

120 V 0-25 26-50 51-100 101-150

Amperaje

Más No más Calibre AWG

de de

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 No recomendado

CARACTERÍSTICAS

ESPECIFICACIONES DEL PRODUCTO

CS34016S

Entrada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 voltios, 60 Hz, 13 amp

Longitud de la barra/Tipo. . . . . . . . . . . . . . . . . . Barra Oregon de 406 mm (16 pulg.)/160SDEA041

Longitud de la cadena/Tipo. . . . . . . . . . . . . . . . .Cadena Oregon de 406 mm (16 pulg.)/91PX057X

Peso . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 kg (12 libras)

- Lubricación automática de la barra y la cadena - Sistema de tensado de cadena sin herramientas -

- Ventana de nivel de aceite - Mango de caucho sobremoldeado -

5

Modelo CS34016S

CABLE

MANGO

TRASERO

VENTANA DE NIVEL

DE ACEITE

TAPA DEL TANQUE

DE ACEITE

MANGO

DELANTERO

PROTECTOR

MANUAL

TAPA DE CADENA

PERILLA DE SEGURIDAD

RUEDA TENSORA

CADENA

BARRA

BOTÓN DE

DESBLOQUEO

DEL GATILLO

INTERRUPTOR DE GATILLO RETENEDOR DE CABLE

6

Modelo CS34016S

PELIGRO: Nunca encienda el motor antes de instalar la barra guía,

la cadena y la tapa de la cadena. Si estas piezas no están en su

lugar, el embrague puede salir disparado o explotar, lo que

expondrá al usuario a una posible lesión grave.

ADVERTENCIA: Para evitar lesiones personales graves, lea y

comprenda las instrucciones de seguridad provistas.

ADVERTENCIA: Antes de realizar alguna tarea de mantenimiento,

asegúrese de que la herramienta esté desconectada del suministro

eléctrico. De lo contrario, podría sufrir lesiones personales de gravedad.

PRECAUCIÓN: Use siempre guantes al manipular la barra y la

cadena. Estos componentes son filosos y pueden contener rebabas.

ADVERTENCIA: Nunca toque o ajuste la cadena mientras el motor

está en funcionamiento. La cadena de la motosierra es muy filosa;

por lo tanto, siempre utilice guantes de protección al realizar el

mantenimiento de la cadena para evitar posibles laceraciones

graves.

NOTA: Use únicamente piezas de reemplazo idénticas al

reemplazar la barra guía y la cadena.

REEMPLAZO DE LA CADENA DE LA MOTOSIERRA

• Desconecte la motosierra del suministro eléctrico. Coloque la

motosierra sobre una superficie plana.

• Desenrosque la tuerca girando la perilla en sentido contrario a las

agujas.

• Retire la tapa de la cadena.

• Retire el ensamble de la barra y la cadena de la superficie de

montaje.

• Retire la cadena vieja de la barra.

• Extienda la nueva cadena de la sierra formando círculo y enderece

todo retorcimiento presente en la misma. Los dientes de corte

deben estar orientados en la dirección desplazamiento de la

cadena. Si están orientados en la dirección opuesta, invierta la

posición de la cadena.

MONTAJE

DESEMBALAJE

Este producto requiere no montaje.

LISTA DE EMBALAJE

• Motosierra

• Funda de cuchillas

• Manual del operario

Extraiga la herramienta y los accesorios de la caja con cuidado.

Asegúrese de que estén incluidos todos los elementos detallados en

la lista de embalaje.

Inspeccione el producto detenidamente para corroborar que no

existan roturas ni averías ocurridas durante el envío. No deseche el

material de embalaje hasta haber inspeccionado exhaustivamente el

producto y comprobar que funciona en forma satisfactoria.

ADVERTENCIA: Si falta alguna pieza o está dañada, no utilice este

producto hasta reponer la pieza en cuestión. De lo contrario, podría

sufrir lesiones personales de gravedad. Si falta alguna pieza o está

dañada, llame al 1-800-618-7474 para obtener asistencia.

REEMPLAZO DE LA BARRA GUÍA Y LA CADENA

TAPA DE CADENA PERILLA DE SEGURIDAD

Dirección de corte

La page charge ...

Scotts CS34016S Manuel utilisateur

Scotts CS34016S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents