Samsung Electronics WIC212S IoT Module Mode d'emploi
- Taper
- Mode d'emploi
Theory of Operation WIC212S IoT Module
SAMSUNG ELECTRONICS 09/07/22
Introduction
The WIC212S is a IoT Module for Home automation networks.
Connected to the TV-remote control device, it acts as a pathway between remote home automation.
Power is provided by External 5V power supply with 10pin zip type connector.
Networking
The WIC212S is applied EFR32 IoT Multi-Protocol of Silicon Labs.
The IoT Module delivers the information received from the remote control device to the main
board with 10pin zip type connector.
Power Source
The WIC212S is powered by an external 5VDC@500mA regulated power source with
10pin zip type connector.
Indication
None.
Expansion Ports
None.
Europe
US/Canada
FCC approval
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two
Conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undes-
irable operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in aresidential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installedand used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this e-
quipment doescause harmful interference to radio or television reception, which can be determ-
ined by turning the equipment off and on, the user is encouraged to try to correct the interferenc
e by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/ TV technician for help.
-The OEM integrator is responsible for ensuring the end-user has no manual instruction to
remove or install module.
-The module is limited to installation in mobile or fixed applications.
IC approval
This device contains licence-
exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
development Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired oper
ation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’
Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptib
le d’en compromettre le fonctionnement.
IMPORTANT NOTE
This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environ
ment. This device should be installed and must not be colocated or operating in conjunction
with any other antenna or transmitter.
This device is intended only for OEM integrators under the following conditions:
1) This module may not be co-located with any other transmitters or antennas.
2) The antenna must be installed such that 20cm is maintained between the antenna and users.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end product for any additional compliance
requirements with this module installed.
In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer
considered valid and the FCC ID cannot be used on the final product. In these circumstances,
the OEM integrator will be responsible for reevaluating the end product including this module
and obtaining separate FCC & IC authorizations.
Cet appareil est conforme aux limites de la FCC et IC exposition aux radiations dans un environne
ment non contrôlé.
Cet appareil doit être installé et ne doit pas être co-localisées ou opérant en conjonction avec
une autre antenne ouun autre émetteur.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes :
1 ) L' antenne doit être installée de telle sorte que 20 cm est maintenue entre l'antenne et les utili
sateurs .
2 ) Ce module ne peut pas être co-localisé avec d'autres émetteurs ou des antennes .
Aussi longtemps que deux conditions précitées sont remplies, le test du transmetteur supplément
aires ne serontpas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leurs
produits finis pour toutes lesexigences de conformité supplémentaires avec ce module installé.
Dans le cas où ces conditions ne peuvent pas être remplies, alors la FCC et IC autorisations ne so
nt plus considérés comme valides et l'ID de la FCC ne peut pas être utilisé sur le produit final.
Dans ces circonstances, l'intégrateur OEM sera responsable de réévaluer le produit final, y
compris l'obtention de ce module et séparée de la FCC et IC Autorisations
User Information
Caution: Any changed or modifications not expressly approved by the party responsible for compl
iance could void the user`s authority to operate this equipment.
Attention: Toute changé ou modifications non expressément approuvés par la partie responsable
de la conformité pourraient annuler l'utilisateur `autorité de faire fonctionner cet équipement.
Antenna information
This module is certified with the following antenna.
Type : Patch antenna
Antenna Gain : 1.60dBi
Frequency range : 2405MHz ~2480MHz
*Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive
change procedure.
The module has been certified for use under FCC Part 15.247/RSS-247 only
Host labeling requirement:
“Contains FCC ID: A3LWIC212S , IC : 649E-WIC212S”
As well as the model name: “WIC212S”
If the module's FCC/IC ID is not visible when installed in the host system then the host system shall be labeled with
"Contains FCC ID: A3LWIC212S / IC ID: 649E-WIC212S ".
The host devices user manual shall contain, in addition to the compliance information required for the host system for
e.g. Part 15 subpart B, the following statements:
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
To verify that your installation of the module into your host device has not compromised compliance with FCC rules we
recommend performing spot checks with the module operational to check that emissions remain below the FCC 15.247
limits.
Refer to FCC KDB 996369 D04.
The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.247 and that the host product
manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. This includes Part 15 subpart B requirements for unintentional radiators.
Host manufacturers are responsible for the approvals of the host system with this module installed for Part 15 B when
applicable following the appropriate procedures for SDoC or certification.
-
1
-
2
-
3
-
4
-
5
