Lifesmart 411441309702 Manuel utilisateur

Check out the LifeSmart Spas channel on YouTube

for helpful videos on spa ownership.

OWNER’S MANUAL 60Hz

ESTRELLA™L • ESTRELLA™NL • CARINO™ • PLAYA™

LIFESMART OWNER'S MANUAL

230V Systems

Locating the Spa Serial Number:

The spa serial number label is located inside the equipment compartment. Equipment

compartment access panel is below the spas topside control panel. Write your spa information in

the space provided.

DATE PURCHASED:

PURCHASED FROM:

SPA MODEL:

SERIAL NUMBER:

Please read this Owner’s Manual carefully, as it is designed to provide you with the information

you will need to ensure the safe, secure use of your spa.

IMPORTANT: LIFESMART reserves the right to change specifications and/or design without

notification and without any obligation.

SPA SPECIFICATIONS

Model Spa

Seating

Length Width Height Dry Weight Water

Capacity

Electrical

60Hz

Carino™ 6 person 89" (226 cm) 89" (226 cm) 36" (91 cm) 918 lbs (416 kg) 409 (1548 lit) 230V

Estrella™ L 6 person 84" (213 cm) 84" (213 cm) 36" (91 cm) 796 lbs (361 kg) 330 (1249 lit) 230V

Estrella NL 7 person 84" (213 cm) 84" (213 cm) 36" (91 cm) 818 lbs (371 kg) 360 (1363 lit) 230V

Playa™ 3 person 65" (165 cm) 84" (213 cm) 29.5" (75 cm) 663 lbs (301 kg) 210 (795 lit) 230V

CAUTION

DO NOT OPERATE SPA BEFORE READING THIS MANUAL

Failure to read this manual and follow its instructions may result in unsafe operation and or

permanent damage to your portable spa.

Most cities, counties, states, and countries require permits for exterior construction and electrical

circuits. In addition, some communities have codes requiring residential barriers such as fencing

and/or self-closing gates on the property to prevent unsupervised access to a pool or spa by

children. Be sure to check with your local agencies for specific requirements.

If you need additional information and/or assistance, please contact Customer Service at

888-961-7727 Ext. 8440 or at [email protected].

Owner's Record

See Page 7

TITLE PAGE

TABLE OF CONTENTS

CONTENTS

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................................................1

IMPORTANT SPA INSTRUCTIONS ............................................................................................................................................4

INSTALLATION

PLANNING A LOCATION FOR YOUR SPA ...............................................................................................................................5

PLACING THE SPA ......................................................................................................................................................................6

EQUIPMENT ACCESS

EQUIPMENT ACCESS PANEL ...................................................................................................................................................7

ELECTRICAL REQUIREMENTS

ELECTRICAL REQUIREMENT ...................................................................................................................................................8

ELECTRICAL WIRING DIAGRAM 230V USE ...........................................................................................................................9

CONTROL PANEL OPERATION

DISPLAY OVERVIEW ................................................................................................................................................................10

TEMPERATURE ADJUSTMENT .............................................................................................................................................10

JETS OPERATION .....................................................................................................................................................................11

MULTI COLOR LED LIGHT .......................................................................................................................................................11

MODE ..........................................................................................................................................................................................11

FILTER CYCLES ........................................................................................................................................................................11

OPERATIONAL MODES ............................................................................................................................................................ 12

DIAGNOSTIC LCD MESSAGE ................................................................................................................................................13

COMPONENT OPERATION

SPA COMPONENT OPERATION .............................................................................................................................................14

FILL-UP AND START-UP INSTRUCTIONS

FILLING THE SPA WITH WATER .............................................................................................................................................15

APPLYING POWER ...................................................................................................................................................................15

ADDING START-UP CHEMICALS

WATER CHEMISTRY GUIDELINES ......................................................................................................................................... 16

SPA MAINTENANCE

FILTER CARTRIDGE MAINTENANCE ....................................................................................................................................17

SURFACE CARE ........................................................................................................................................................................18

COVER CARE ............................................................................................................................................................................18

CABINET CARE ......................................................................................................................................................................... 18

REPLACEMENT PARTS ............................................................................................................................................................ 18

DRAINING OR WINTERIZING

DRAINING YOUR SPA ..............................................................................................................................................................19

WINTERIZING YOUR SPA ........................................................................................................................................................19

TROUBLESHOOTING PROCEDURES

NO COMPONENT OPERATION ............................................................................................................................................... 20

PUMP DOES NOT OPERATE, BUT THE LIGHT DOES ........................................................................................................20

POOR JET ACTION....................................................................................................................................................................20

WATER IS TOO HOT ..................................................................................................................................................................20

1

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

AVOIDING THE RISK TO CHILDREN

DANGER:

• RISK OF CHILD DROWNING: Extreme caution must be exercised to prevent unauthorized access

by children. To avoid accidents, ensure that children cannot use a spa unless they are supervised at

all times. Children should be supervised to not use the spa as a toy.

WARNING:

• To reduce the risk of injury, do not permit children to use this product unless they are closely

supervised at all times.

• To reduce the risk of injury, lower water temperatures are recommended for young children. Children

are especially sensitive to hot water.

DO:

• Make sure you always lock the child resistant locks after using the spa for your children’s safety.

Every spa is equipped with a locking cover that meets the ASTM F1346-91 Standard for Safety

Covers.

• Test the water temperature with your hand before allowing your child to enter the spa to be sure that

it’s comfortable. Children are especially sensitive to hot water.

• Remind children that wet surfaces can be very slippery. Make sure that the children are careful when

entering or exiting the spa.

DON’T:

• Allow children to climb onto the spa cover.

• Allow children to have unsupervised access to the spa.

AVOIDING THE RISK OF ELECTROCUTION

RISK OF ELECTROCUTION:

• Connect only to a grounded source.

• Do not bury the power cord. A buried power cord may result in death or serious personal injury due

to electrocution if direct burial-type cable is not used, or if improper digging occurs.

• A ground terminal (pressure wire connector) is provided on the control box inside the unit to permit

connection of a minimum No. 10 AWG solid copper bonding conductor between this point and any

metal equipment, metal water pipe, metal enclosures of electrical equipment, or conduit within 5 feet

(1.5 m) of the unit as needed to comply with local requirements.

WARNING:

• Your spa must use a Ground Fault Circuit Interrupter for user and equipment protection. To ensure

proper operation of this important safety device, test according to the following instructions per

electrical configuration.

SAFETY INFORMATION

2

230 VOLTS:

• A ground terminal is provided on the control box. To reduce the risk of electric shock, connect this

terminal to the grounding terminal of your electrical service or subpanel with a continuous green,

insulated copper wire. The wire must be equivalent in size to the circuit conductors supplying the

equipment. In addition, a bonding terminal (pressure wire connector) is provided on the outside of

the control box for bonding to local ground points. To reduce the risk of electric shock, this connector

should be bonded with a No. 8 AWG solid copper wire to any metal ladders, water pipes, or other

metal within 5 feet (1.5 m) of the spa to comply with local requirements. The means of disconnection

must be readily accessible, but must be installed at least 5 feet (1.5 m) from the spa.

• Your spa requires a suitably rated circuit breaker to open all ungrounded supply conductors.

• Your spa must have a ground fault circuit interrupter in an electrical subpanel. Before each use of

the spa and with the unit operating, push the TEST button on the breaker. The switch should click

over to the “Trip” position. Wait 30 seconds and reset the GFCI breaker by switching it completely

off and then completely on. The switch should then stay on. If the interrupter does not perform in

this manner, it is an indication of an electrical malfunction and the possibility of an electric shock.

Disconnect the power until the fault has been identified and corrected.

IMPORTANT: Failure to wait 30 seconds before resetting the GFCI may cause the spa’s Power

Indicator (on the control panel) to blink. If this occurs, repeat the GFCI test procedure.

DANGER: RISK OF ELECTRICAL SHOCK

• Install spa at least 5 feet (1.5 m) from all metal surfaces. A spa may be installed within 5 feet (1.5 m)

of a metal surface if each metal surface is permanently connected by a minimum No. 10 AWG solid

copper conductor attached to the wire ground connector on the terminal box that is provided for this

purpose if in accordance with National Electrical Code ANSI/NMFPA70-1993.

• Do not permit any electrical appliances, such as a light, telephone, radio, or television within 5 feet

(1.5 m) of a spa. Failure to maintain a safe distance may result in death or serious personal injury

due to electrocution if the appliance should fall into the spa.

• Install your spa in such a way that drainage is away from the electrical compartment and from all

electrical components.

DO:

• Be sure your spa is connected to the power supply correctly - use a licensed electrical contractor.

• Disconnect the spa from the power supply before draining the spa or servicing the electrical

components.

• Test the Ground Fault Circuit Interrupter before each use.

DON’T:

• Use the spa with the equipment compartment door removed.

• Place electrical appliances within 5 feet (1.5m) of the spa.

• Attempt to open the electrical control box. There are no user serviceable parts inside.

SAFETY INFORMATION

3

RISKS TO AVOID

DANGER: RISK OF INJURY

• DO NOT sit in the filter compartment area. Sitting in this area can cause:

a) Restriction of Filter Pump suction/vacuum b) Damage to components

• Both can result in bodily harm. Should damage occur to components in this area, replace

immediately!

To reduce the risk of injury to persons, DO NOT remove floating weir, basket, and filter located in the filter

compartment while the spa is running.

• The suction fittings in the spa are sized to match the specific water flow created by the pump. Never

replace a suction fitting with one rated less than the flow rate marked on the original suction fitting.

• There is a danger of slipping and falling. Remember that wet surfaces can be very slippery. Take

care when entering or exiting the spa.

• Never operate spa if the suction fittings are broken or missing.

• The device should not be used by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they receive supervision or training.

• People with infectious diseases should not use the spa.

• Keep any loose articles of clothing or hanging jewelry away from rotating jets or other moving

components.

Increased side effects of medication

• The use of drugs, alcohol or medication before or during spa use may lead to unconsciousness with

the possibility of drowning.

• Persons using medications should consult a physician before using a spa; some medication may cause

a user to become drowsy, while other medication may affect heart rate, blood pressure, and circulation.

• Persons taking medications which induce drowsiness, such as tranquilizers, antihistamines or

anticoagulants should not use the spa.

Health problems affected by spa use

• Pregnant women should consult a physician before using spa.

• Persons suffering from obesity or with a medical history of heart disease, low or high blood pressure,

circulatory system problems, or diabetes should consult a physician before using spa.

Unclean water

• Keep the water clean and sanitized with correct chemical care. The recommended levels for your

spa are: Free Available Chlorine (FAC): 3.0-5.0 ppm Total Alkalinity: 40 - 120 ppm

Water pH: 7.2 - 7.8 Calcium Hardness: 75 - 150 ppm

IMPORTANT: Turn jet pump on for at least ten minutes after adding ANY spa water chemicals into the

filter compartment.

• Clean the filter cartridge monthly to remove debris and mineral buildup which may affect the

performance of the hydromassage jets, limit the flow, or trip the high-limit thermostat which will turn

off the entire spa.

AVOIDING THE RISK OF HYPERTHERMIA

Prolonged immersion in hot water can result in HYPERTHERMIA, a dangerous condition which occurs

when the internal temperature of the body reaches a level above normal 98.6°F (37ºC). The symptoms

of hyperthermia include unawareness of impending hazard, failure to perceive heat, failure to recognize

the need to exit the spa, physical inability to exit the spa, fetal damage in pregnant women, and

unconsciousness resulting in a danger of drowning.

SAFETY INFORMATION

4

WARNING:

The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs and

spas.

TO REDUCE THE RISK OF INJURY:

• The water in the spa should never exceed 104°F (40°C). Water temperatures between 100°F

(38°C) and 104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are

recommended for extended use (exceeding 10 minutes) and for young children. Extended use can

cause hyperthermia.

• Pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C). Failure

to do so may result in permanent injury to your baby.

• Do not use spa immediately following strenuous exercise.

AVOIDING THE RISK OF SKIN BURNS:

• To reduce the risk of injury, before entering a spa the user should measure the water temperature

with an accurate thermometer.

• Test the water with your hand before entering the spa to be sure it’s comfortable.

SAFETY SIGN:

A SAFETY SIGN is included in the owner’s package. The sign, which is required as a condition of Product

Listing, should be permanently installed where it is visible to the users of the spa.

IMPORTANT SPA INSTRUCTIONS

The following contains important spa information, and we strongly encourage you to read and apply them.

DO:

• Use and lock the vinyl cover when the spa is not in use, whether it is empty or full.

• Follow the Spa Care and Maintenance recommendations stated in this manual.

• Use only approved accessories and recommended spa chemicals and cleaners.

DON’T:

• Leave the spa exposed to the sun without water or the vinyl cover in place. Exposure to direct

sunlight can cause solar distress of the shell material.

• Roll or slide the spa on its side. This will damage the siding.

• Lift or drag the cover by using the cover lock straps; always lift or carry the cover by using the handles.

• Attempt to open the electrical control box. There are no user serviceable parts inside. Opening of the

control box by the spa owner will void the warranty. If you have an operational problem, carefully go

through the steps outlined in the Troubleshooting section. If you are not able to resolve the problem,

contact

Customer Service (888) 961-7727 Ext. 8440

. Many problems can easily be diagnosed

over the telephone.

INSTALLATION

5

PLANNING A LOCATION FOR YOUR SPA

Consider these things when determining where to place your spa.

SAFETY FIRST:

Make sure your spa is positioned so access to the equipment compartment and side panels

will not be blocked. Be certain your installation will meet all city and local safety codes and

requirements.

PLANNED USE OF SPA:

How you intend to use your spa will help you determine where you should position the spa. For

example, will you use it more for recreational or therapeutic purposes? If your spa is mainly for

family recreation, leave plenty of room around it for activity and lawn furniture. If you will use it

more for relaxation and therapy, you’ll probably want to create privacy around the spa.

PRIVACY:

Think of your surroundings during all seasons to determine your best privacy options. Consider

the view of your neighbors when you plan the location of your spa.

VIEWS:

Think about the direction you will be facing when sitting in your spa. Do you have a special

landscape you will find enjoyable? Perhaps there is an area that has a soothing breeze during the

day or a lovely sunset in the evening.

ENVIRONMENT:

If you live in a climate with a snowy winter and hot summer, a place to change clothes or a house

entry near the spa is convenient. A warmer climate may require shade from the hot sun. Consider

placement of trees, shrubs, patio cover or perhaps a gazebo structure to provide what you will

need. Indoor installations require adequate ventilation. When the spa is in use, considerable

amounts of moisture are produced. This moisture can damage walls and ceiling surfaces over

time. Special paint is available to resist moisture damage. Remember that spas periodically

require drainage, so plan your environment accordingly.

KEEP CLEAN:

Prevent dirt and foliage from being tracked into your spa by utilizing concrete for paths and access

areas. Check the location of spill paths from gutters, trees, and shrubs.

SERVICE ACCESS:

Many people choose to install tile or custom wood around their spas. If you are installing your tub

with custom decorative trimming, remember to allow for access to it for service. Should you need

service, a technician may need to remove the tub’s door panel, or access it from beneath. It is

always best to design special installations so the spa can still be moved, or lifted from the ground.

A GOOD FOUNDATION:

Your new spa needs a good solid foundation. The area your spa sits on must be able to support

the spa, the water in it and those who use it. If the foundation is inadequate, it may shift or settle

after the spa is in place, causing stress to the shell or components. NOTE: Do not shim your spa

in any manner, as this could cause the cabinet to crack, thereby voiding the warranty.

INSTALLATION

6

BE AWARE:

Damage caused by inadequate or improper foundation support is not covered by the spa warranty.

It is the sole responsibility of the spa owner to provide a proper foundation for the spa.

Make sure the foundation where the spa is placed drains water away from the spa. Proper

drainage will keep components dry from rain and wet weather.

Your spa weight must always be considered when installing your spa. If you are installing it on an

elevated wood deck or other structure, it is advisable to consult a structural engineer or contractor

to ensure the structure will support the weight.

IT IS STRONGLY RECOMMENDED THAT A QUALIFIED, LICENSED CONTRACTOR

PREPARE THE FOUNDATION FOR YOUR SPA.

A reinforced concrete pad at least four inches thick is recommended for your spa. The reinforcing

rod or mesh in the pad should be attached to a bond wire.

INDOOR INSTALLATION:

Be aware of some special requirements if you place your spa indoors. Water will accumulate

around the spa, so flooring materials must provide a good grip when wet. Proper drainage is

essential to prevent a build-up of water around the spa. When building a new room for the spa, it

is recommended that a floor drain be installed. The humidity will naturally increase with the spa

installed. Water may get into woodwork and produce dry rot, mildew, or other problems. Check for

airborne moisture’s effects on exposed wood, paper, etc. in the room. To minimize these effects, it

is best to provide plenty of ventilation to the spa area. An architect can help to determine if more

ventilation must be installed.

PLACING THE SPA

CHECK THE DIMENSIONS OF YOUR SPA:

Compare the spa dimensions to the width of gates, sidewalks, and doorways along the delivery

route used to bring the spa into your yard. It may be necessary for you to remove a gate or

partially remove a fence in order to provide an unobstructed passageway to the installation

location. Also, keep in mind—if you are using special equipment to place your spa into an area it

will be necessary to include those measurements and weights.

PLANNING A DELIVERY ROUTE:

Check the width of gates, doors and sidewalks to make sure your spa will pass through

unobstructed. You may have to remove a gate or part of a fence to allow for adequate width

clearance. If the delivery route will require a 90-degree turn, check the measurements at the turn

to ensure the spa will fit. Check for protruding gas meters, water meters, A/C units, etc., on your

home which will cause obstructions along the delivery path to your yard. Check for low roof eaves,

over hanging branches or rain gutters that could be an obstruction to overhead clearances.

SPECIAL CIRCUMSTANCES:

The use of a crane for delivery and installation is primarily to avoid injury to your spa, your

property or to delivery personnel. Cranes are not considered “normal delivery”.

EQUIPMENT ACCESS

7

Drain

Topside Control Panel

Door Panel

To access the equipment compartment:

Remove all the screws around the top, bottom and sides of the large full panel door. Lower

door panel slightly, pull bottom of door away from spa then remove.

Equipment Compartment

EQUIPMENT ACCESS PANEL

Electrical

Access

Electrical

Access

Serial No.

8

ELECTRICAL REQUIREMENT

DO NOT POWER THE SPA WITHOUT FIRST FILLING WITH WATER!

DANGER – RISK OF ELECTRIC SHOCK

Installations that do not conform to the following procedures and requirements may expose

users to electric shock. Non-conforming installations will not be covered under warranty.

If installed in the United States, the electrical wiring of this spa must meet the requirements of the

National Electric Code (NEC) and any applicable state or local codes. The electrical circuit must be

installed by an electrical contractor and approved by a local building electrical inspection authority.

1. Installations within 5 feet

(1.5 m)

of any metal surfaces must ground the metal surfaces to the

hot tub. Use an 8 AWG solid copper wire and attach it to the grounding lug on the control box,

located in the equipment compartment.

2. Only a licensed electrician may install power to the spa.

3. Power supply installation must include a suitably rated ground fault circuit interrupter (GFCI)

as required by NEC Article 680-42. The circuit breaker must be dedicated and should not be

shared with any other appliances. It must be labelled and easily accessible to users.

4. The electrical supply for the spa must include a suitable rated switch or circuit breaker to open

all ungrounded supply conductors to comply with Section 422-20 of the National Electric Code,

ANSI/NFPA 70. The disconnecting means must be readily accessible to the spa’s occupant but

installed at least 5 feet

(1.5 m)

from the spa water.

5. 230V Power supply lines must be hard wired into the control box. DO NOT use extension or

plug-type cords of any kind. The use of a shut-off box near the hot tub is also recommended.

This box provides a quick and convenient method to shut off power to the hot tub for

emergencies and maintenance.

6. Supply lines must be properly sized as per the NEC. A ground line must be provided that is

as large as the largest current carrying conductor, but no less than 8 AWG. Use copper wiring

only.

7. Please open the front cover of the control box, and follow the instructions and wiring diagram

printed on the backside.

8. CAUTION, 230V POWERED SPA – This spa

must be hard wired to your household electrical

service box only. Do not use an extension cord

or any other disconnect-able power cord. The

use of an extension cord or a disconnect-able

power cord is highly dangerous and will void all

warranties!

• Wire size must be appropriate per NEC and/or

local codes.

• Wire size is determined by length of run from

breaker box to spa and maximum current draw.

• THHN copper core wire is recommended.

• All wiring must be copper to ensure adequate

connections. Do not use aluminum wire.

ELECTRICAL REQUIREMENTS

Equipment access is below

the topside control panel.

Topside Control Panel

9

ELECTRICAL REQUIREMENTS

ELECTRICAL WIRING DIAGRAM 230V USE

It is recommended that a licensed electrician install the power to your spa in accordance with the

National Electric Code and/or any local electrical codes in effect at the time of installation.

Power supply installation must include a properly rated GFCI circuit breaker. The circuit must be

dedicated and should not be shared with any other appliances. The power supply must be hard

wired into the power pack.

White Neutral Wire that is connected

to Spa Neutral goes HERE.

230V Wiring Instructions:

4 wires/50 amp GFCI Breaker #8 AWG 75°C

Copper Wire Minimum (less than 100’ (30

m) length)

Special Note:

If the GFCI breaker trips immediately

after attempting to turn on, please check the

White Neutral Wire that is connected to the

spa.

From the House

Breaker Box To the Spa

Red

White

Black

Green

10

INITIAL START-UP -

When the spa is first powered up the control system begins

a 2 minute Startup Mode. Different codes will display on the screen. Once Startup

Mode completes, the actual temperature is

displayed on the screen, and the spa will

then begin to heat, maintain the

water temperature and the first

filter cycle will start 5 minutes

later. Your spa has been designed

so that it will automatically heat the water

to the factory set temperature of 100°F

(38°C) unless you set the spa to a different

temperature. If power is disconnected from

the spa, it will automatically revert back to

the last saved set temperature when power is reapplied. NOTE: Some models only have Jets 1

DISPLAY OVERVIEW

TEMPERATURE ADJUSTMENT

The temperature can only function between 80°F - 104°F (26.5°C - 40°C). The last measured

temperature will constantly display on LCD.

Press the Up/Plus or Down/Minus buttons to display the set temperature

(desired temperature) and indicator . Each time either button is pressed

again, the set temperature will increase or decrease depending on which

button is pressed. After five seconds, the LCD will automatically display the

current spa temperature.

The “heater” indicator

lights up when the heater is on. It flashes when there is a request for

more heat, but the heater is not on. Once set temperature is reached the indicator shuts off and

the low speed of the jet pump turns off after 30 seconds (if not in filter cycle).

CONTROL PANEL OPERATION

Temp Down/

Minus

Temp Up/

Plus

Jets 1 Jets 2 Lights

Mode

Pumps icon

The "Pump" indicator lights up when

the pump is in high speed, and flashes

when the pump is in low speed.

Some models only have 1 pump.

Service icon

A problem has

been detected. Do

not enter the water!

Spa service is

required.

Temperature

& message digits

˚F/ ˚C

Filter Cycle icon

The "Filter Cycle" icon lights

up when filter cycle is on. The

icon flashes if the filter cycle is

disrupted.

Smart Winter Mode icon

The "SWM" icon

automatically turns on

when freeze protection

is active. It flashes while

system purges the spa

plumbing.

Set Point icon

The "Set Point" icon

automatically turns on

when set point setting

menu is activated.

Light icon

The "Light" icon lights up

when the light is on.

Heater icon

The "Heater" icon lights up when the heater is on. It

flashes when:

1- there is a call for heat and heater has not started yet,

2- heater has just turned off and element is cooling

down or

3 - not enough current available to start heater

11

CONTROL PANEL OPERATION

JETS OPERATION

Jet Pump 1 button:

• Press Jets 1 button once to turn Jet Pump 1 on low speed.

• Press Jets 1 button a second time to turn Jet pump1 on high speed.

• Press Jets 1 button a third time to shut Jet Pump1 off.

Jet Pump 2 button: (Not available on all models)

• Press Jets 2 button once to turn Jet Pump 2 On.

• Press Jets 2 button a second time to shut Jet Pump 2 Off.

MULTI COLOR LED LIGHT

Press the Light button once to turn on the lights, press the button again to turn the lights off, when

turning back on after several seconds the same light mode will appear. Every time the light is

quickly turned off and on a new light mode will appear. The sequence is as follows:

White, Aqua, Magenta, Azure, Amber, Emerald, Ruby, Color wheel with abrupt

color changes, Slow full color wheel and Fast full color wheel.

NOTE: If left on, the light will automatically turn off after 4 hours of operation.

MODE

CLEANUP MODE (2 pump models only)

Press the Mode button to start the cleanup cycle for one minute. The display will

show CLn” message. This mode forces a purge step of the programmed filter

cycle and is useful when the user wishes to cleanup the spa water after use

without waiting for the next filter cycle purge. When active, the display will toggle

between CLn and water temperature.

SOAK MODE (2 pump models only)

Press and hold the Mode button for 5+ seconds until SbY is displayed. The soak mode clears

all pending user demands as well as filtration and smart winter mode. The only

automatic feature that remains functional is the water temperature regulation.

OFF MODE (all models)

Press and hold the Mode button for 8+ seconds until OFF is displayed. This

function is useful to preform simple spa maintenance. When enabled the display will toggle

between OFF and water temperature. This function will clear all pending user demands for 60

minutes. This mode will be cancelled if the user starts a pump.

NOTE: If the spa is calling for heat it will take 1 minute before the jet pump will shut off.

FILTER CYCLES

There are two filter cycles: the first cycle (F1) starts right after power up and the second cycle (F2)

will start 12 hours later. The default duration for the first filter cycle is 1 hour, and 30 minutes for the

second cycle. The “Filter” indicator lights up when a filter cycle is on. The duration of each filter

cycle can be

modified. If

the “Filter” indicator flashes this indicates there has been a suspension

in the filter cycle.

12

ADJUSTING PRESET FILTER CYCLES

Filter duration is programmable between 0.5 and 6 hours in 30 minute increments (0.5 hours) for

both filter cycles. To program the cycle times:

1. Press and hold Light button for 5+ seconds until F1 is displayed.

2. Press the Plus or Minus button to adjust the cycle time for F1.

3. Press the Light button to store the F1 cycle and move to the F2 cycle.

4. Press the Plus or Minus button to adjust the cycle time for F2.

5. Wait 15 seconds to allow the exit timer to expire and store the setting.

IMPORTANT: To reset the first filter cycle start time, skip step 5 and continue pressing the Light

button until the actual temperature is displayed. Powering down of the spa will also reset the first

filter start time.

FILTER CYCLE SUSPENSION:

The filter cycle will be suspended every time a jet pump or

light is activated manually during the filter cycle time. The suspension will end around 15 minutes

after the completion of the manual use.

FAHRENHEIT/CELSIUS SETTING:

To change water temperature display to either Fahrenheit or Celsius, press and

hold Light button for 5+ seconds until F1 is displayed. Press the Light button

several times until F or C is displayed. Press the Plus or Minus button to

change. Wait 15 seconds to allow the exit timer to expire and store the setting.

ECONOMY MODE:

(2 pump models only)

This mode allows you to lower the temperature set point of the spa by 20°F

(11°C), to change to the Economy mode press and hold Light button for 5+

seconds until F1 is displayed. Press the Light button several times until the

display shows EP 1, use Down key to disable economy mode, the display will

show EP 0. Wait 15 seconds to allow the exit timer to expire and store the setting.

OPERATIONAL MODES

(1 pump models only)

The Standard Mode is the default operational mode preset from the factory. In order to program the

spa to operate in the Economy mode you must enter the programming mode to make the change.

Water sampling will turn the jet pump on and circulate the water for up to a couple of minutes.

NOTE: Freeze Protection (Smart Winter Mode) will assert as necessary during all modes.

STANDARD MODE:

Is programmed to maintain the desired temperature with periodic water

circulation (sampling) to sample and heat the water to the set temperature.

ECONOMY MODE:

The spa will not heat. Water sampling only done during the filter cycle.

SLEEP MODE:

The spa will only heat during the filter cycles. Water sampling only done during the filter

cycle.

QUIET MODE:

Keeps the jet pump from running (water sampling) after the F2 filter cycle is complete for

up to 11.5 hours. You can set this mode between 0.5 hours and 11.5 hours in half hour increments.

To enter the programming screen and toggle between Standard, Economy, Sleep and Quiet

Modes the following is required:

CONTROL PANEL OPERATION

13

1. Press and hold the Light button for 5 seconds

2. Press the Light button several times until St, Ec, SL, or nt is displayed.

3. Use the Plus or Minus button to choose between the Modes.

St = Standard Mode, Ec = Economy Mode, SL Sleep = Mode and nt = Quiet Mode.

4. Wait 15 seconds to allow the exit timer to expire and store the setting.

To Program the Quiet Mode the following is required:

Once in the nt mode, press the Light button then press the Up/Down button to change the amount of time

you do not want the jet pump to come on between F2 and F1.

DIAGNOSTIC LCD MESSAGE

Message Meaning Action Required

No message on display.

Power has been cut off to the spa.

The control panel will be disabled until power

returns. Spa settings will be preserved until

next power up.

HL The system has shut the heater

off because the temperature at the

heater has reached 119°F (48°C).

Do not enter the water!

DO NOT ENTER THE WATER. Remove the

spa cover and allow the water to cool down,

then shut power off and power your spa up

again to reset the system.

If spa does not reset, shut off the power to the

spa and call Customer Service at

(888) 961-7727 Ext. 8440 or at ahsservice@

watkinsmfg.com.

AOH Temperature inside the equipment

compartment is too high 194F

(90°C), causing the internal

temperature in the control system to

increase above normal limits.

Open equipment compartment and wait until

error clears.

Prr A problem is detected with the

temperature probe.

Call Customer Service at (888) 961-7727 Ext.

8440 or at [email protected].

OH The water temperature in the spa

has reached 108°F (42°C). Do not

enter the water!

Remove the spa cover and allow the water to

cool down to a lower temperature. Call

Customer Service if problem persists.

Hr An internal hardware error has been

detected.

Call Customer Service. at (888) 961-7727 Ext.

8440 or at [email protected].

FLO No water flow is detected by the

control system but flow is expected.

Make sure that the jet pump is running and

water is flowing; check and clean filters; make

sure water valves are open; make sure spa

has a proper water level. If problem persists,

call Customer Service at (888) 961-7727 Ext.

8440 or at [email protected].

WARNING! SHOCK HAZARD! NO USER SERVICEABLE PARTS.

Do not attempt service of the control box. Contact Customer Service at (888) 961-7727

Ext. 8440 for assistance. Follow all owner manual power connection instructions. Installation must

be performed by a licensed electrician and all grounding connections must be properly installed.

CONTROL PANEL OPERATION

14

COMPONENT OPERATION

SPA COMPONENT OPERATION

AIR CONTROL VALVE

The air control valves (smaller valves) serve to regulate the amount of air mixed with the water

when the jets are operational. Turn the air control valves in one direction to increased jet action.

Rotating the air control in the opposite direction to turn air off and allow the jets to work with water

only. Turn the air controls off when the spa is not in use, this will prevent cold air from entering the

spa and will keep heating cost to a minimum. The ozone jet, will always produce air bubbles when

pump is on.

HYDROTHERAPY JETS

The hydrotherapy jets are recessed in the wall of the spa. Rotate the large or medium jet faces to

turn the jets on or off. Turning a jet on or off will increase or decrease the effects of any jets not in

the closed position.

OZONE GENERATOR

The ozone system enhances the quality of the spa water when used to supplement the spa

owner’s regular water maintenance program. Contrary to some information circulated throughout

the pool and spa industry regarding ozone systems, ozone CAN'T be used as a single-

source sanitizer, water clarifier, anti-foamer, and mineral chelating agent. A secondary source

sanitizer must be used to maintain 3.0 -5.0 ppm of Free Available Chlorine (FAC). LIFESMART

recommends that a chemical maintenance program based on recognized and documented

industry standards still be followed when using an ozone purification system to assure water

sanitation and the highest quality purified water.

WATERFALL

Your spa has a control valve to operate the amount of flow through the waterfall from no flow to a

steady stream. This valve is attached to the top and bottom of the waterfall. The waterfall will only

work when Jet Pump is on. Move valve side to side to turn on or off.

MUSIC (WHEN EQUIPPED)

Your spa is equipped with a Bluetooth music sound system that requires a bluetooth device to pair

up with the spa. To pair the spa and Bluetooth device:

• Go to the Bluetooth settings on you device and find in.stream 2 and press connect.

• Enter pin 5555 and press pair to sync your device. You are now ready to play audio from your

device.

The following procedures should be followed on initial startup and whenever the spa is drained for

routine maintenance.

FILLING THE SPA WITH WATER

1. Clear all the debris from your spa.

2. Be sure to open all jets to allow as much air as possible to escape from the plumbing during

the filling process.

3. Insert a garden hose into filter compartment to fill your spa.

NOTE: Do not use hot or softened water.

4. As the water level

rises, check inside

the equipment

compartment for

water leaks. It may

be necessary to

tighten unions

and/or fittings

that may have

loosened during

delivery. There is

no need to call for

service; this can

easily be done.

If assistance is

required, contact a Customer Service representative at (888) 961-7727 Ext. 8440.

5. Under normal circumstances keep the water level half way between the top of the spa and the

top of the filter ring or just above the highest jets (whichever is higher).

Failure to keep enough water in your spa may result in damage to your system and invalidate your

warranty. If your spa filter is sucking in air causing the pump to cavitate, you need to add water!

6. Check the filter installation and make sure the filter is not loose.

APPLYING POWER

1. Turn power to spa "ON" (after filling spa) from the main panel at the house and the subpanel.

2. Press Jets button on the topside control panel to activate the spa. Rotate all the air control

valves clockwise and observe the increased jet action (air mixed with water). After several

minutes.

3. While the pump is running check again for water leaks at the drain spigot, unions, or fittings in

the equipment compartment (leaks may have occurred during transit). If water is leaking from

one of these areas, there is no need to call for service. Simply tighten the fitting. If assistance

is required, call a Customer Service representative at (888) 961-7727 Ext. 8440.

4. After checking your spa for leaks it is now time to adjust your spa settings. Press the

Plus or Minus button on your topside control panel until the display indicates your desired

temperature is set, after 5 seconds of non activity the control panel will display the actual water

temperature.

15

FILL-UP AND START-UP INSTRUCTIONS

UNIONS

EQUIPMENT COMPARTMENT

16

ADDING START-UP CHEMICALS

WATER CHEMISTRY GUIDELINES

Spa water chemistry is ultimately the responsibility of the spa owner. Improper water chemistry may result

in costly repairs not covered under the spa warranty. If unsure about any step in the process, please

contact a Customer Care Associate at (888) 961-7727 Ext. 8440 or at [email protected].

Initially, it is advisable to identify what minerals (e.g. iron) are present in the local source water. This will

provide a better understanding of how to treat the water. Please follow the four steps below and be sure to

achieve the correct levels in each area before moving onto the next step.

STEP #1: ESTABLISH PROPER PH LEVEL:

The recommended range for pH is between 7.2 and 7.8. Above 7.8, the water is too alkaline and can

result in cloudy water, and scale formation on the shell and heater. To lower the pH use a pH Down/

Decreaser (sodium bisulfate). Below 7.0 (considered neutral), the spa water is too acidic and can

damage the heating system. To increase pH, use a pH Up/Increaser (sodium hydrogen carbonate).

Any pH Up or Down should be added one teaspoon at a time, waiting one-half hour between

application and re-measuring.

STEP #2: MEASURE TOTAL ALKALINITY:

The Total Alkalinity is the amount of bicarbonates, carbonates, and hydroxides present in the spa

water. Proper total alkalinity is important for pH control. If the TA is too high, the pH is difficult to

adjust. If the TA is too low, the pH will be difficult to hold at the proper level. The ideal range is

between 40-120 parts per million (ppm). Reduce TA by using an Alkalinity Down/Decreaser (sodium

bisulfate). Increased TA by adding an Alkalinity Up/Increaser (sodium bicarbonate or sodium hydrogen

carbonate). These products should be added in small amounts - 5 ml at a time. After adding 5 ml, wait

one half hour before re-measuring. Once the safe range of total alkalinity is established, proceed to the

next step.

STEP #3: DETERMINE CALCIUM HARDNESS:

It is important to bring the calcium reading to between 75-150 ppm. If the reading requires adjustment,

it should now be corrected. If the water is too soft (a low reading) calcium hardness should be added to

the water to increase the ppm reading. If the water is too hard (a high reading), it can be corrected by

either: (A) a mixture of hard and soft water added to attain a reading in the safe range, or (B) addition of

stain and scale control. If calcium hardness is a problem with the local source water (either too hard or

too soft) a test kit, which measures calcium hardness, is essential.

STEP #4: SANITIZING:

After steps 1-3 are complete, the spa must be sanitized using Chlorine (sodium dichlor). Add 2

teaspoons of Chlorine, and increase as necessary to reach a level of 3-5 ppm. Check and maintain

this level weekly, and before and after using the spa. IMPORTANT NOTE: A granulated sodium dichlor

is highly recommended for sanitizing spa water, granular bromine may also be used. Never use

compressed sanitizers even with a floater. As with any other chemicals, the sanitizer should be

introduced to the spa with the jets running for 10 minutes.

WEEKLY SHOCK:

Using a potassium monopersulfate (MPS) shock, add approximately 2 oz. (60 ml) spreading it over the

water while the jets are running. Shocking is achieved by adding the MPS to turbulent water. Leave the

cover up and jets on high for 10 minutes. Then shut jets off and return the cover to the closed position

to maintain heat.

17

SPA MAINTENANCE

FILTER CARTRIDGE MAINTENANCE

At least once a week, check and clean the skimmer basket and weir to ensure proper filter flow.

Remove leaves, foreign matter, and debris. It is very important to keep your spa filter cartridge

clean and free of particles to ensure proper water flow. A clean filter permits the hydrotherapy

system to function properly and also allows more efficient filter cycles. Depending on how

frequently your spa is used, we recommend cleaning the spa filter cartridge every four weeks. If

this is not done, the filter may clog and restrict water flow, which causes improper filtration and

poor jet performance.

IMPORTANT: The frequency and duration of use, and the number of occupants all contribute to

determining the appropriate time between filter cleanings. More use means that more frequent

filter cleanings will be required.

FILTER CARTRIDGE REMOVAL AND CLEANING

INSTRUCTIONS

1. Press Mode button for 8+ second to OFF.

2. Pull out the basket and weir.

3. Carefully unscrew the filter cartridge and bring it out

of the spa.

4. Always clean the filter using a filter degreaser

to remove mineral and oil build-up. Soak the

filter in the degreaser (according to the package

directions). Then place the filter on a clean surface

and, using a garden hose, spray until it is clean. It

may be necessary to rotate the filter while spraying

to remove any debris lodged between the filter

pleats.

5. Replace the cartridge in the spa. Lower the basket

and weir over filter cartridge.

6. Turn on power by pressing jets button.

CAUTION! Always use proper eye protection when

using chemicals, or high-pressure water. Read

instructions on cleaning products and follow applicable

safety and warning instructions listed on label.

CAUTION! Never scrub the filter cartridge with a brush, as this will cause the filter to wear out and

come apart. Never let the spa pump run without a filter cartridge in the skimmer compartment.

Running the spa without a filter cartridge may permit debris to enter the spa plumbing and void the

warranty!

• Replace filter cartridge, then reinstall basket and weir, (insert and rotate clockwise to lock into

position). DO NOT OVERTIGHTEN!

• Turn spa’s power back on.

BASKET &

WEIR

FILTER

CARTRIDGE

La page est en cours de chargement...

Lifesmart 411441309702 Manuel utilisateur

Ce manuel convient également à

Lifesmart 411441309702 Manuel utilisateur

dans d''autres langues