ATEN CL1308N Manuel utilisateur

CL1308 / CL1316

8 / 16-Port VGA Single Rail

LCD KVM Switch

User Manual

CL1308 / CL1316 User Manual

ii

Compliance Statements

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Caution

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

Warning

Operation of this equipment in a residential environment could cause radio

interference

.

Achtung

Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen

verursachen.

KCC Statement

RoHS

This product is RoHS compliant.

CL1308 / CL1316 User Manual

iii

About this Manual

This user manual is provided to help you get the most out of your CL1308 /

CL1316. It covers all aspects of the device, including installation,

configuration, and operation.

The LCD KVM switch models covered in this manual include:

An overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the CL1308 / CL1316, its

purpose, features, and benefits, with its front and back panel components

described.

Chapter 2, Hardware Setup, describes how to set up your CL1308 /

CL1316, and the necessary steps — from a basic single-level hookup to a

complete 17-switch two level operation.

Chapter 3, Basic Operation, explains the fundamental concepts involved

in operating the CL1308 / CL1316.

Chapter 4, OSD Operation, provides a complete description of the

CL1308 / CL1316 OSD (on-screen display), and the various functions

provided.

Chapter 5, Keyboard Port Operation, details all of the concepts and

procedures involved in the hotkey operation of your CL1308 / CL1316

installation.

Chapter 6, Keyboard Emulation, provides tables that list PC-to-Mac and

PC-to-Sun keyboard emulation mappings.

Chapter 7, The Firmware Upgrade Utility, explains how to upgrade the

CL1308 / CL1316’s firmware to the latest available versions using the

firmware upgrade utility.

An Appendix, provides the specifications and other technical information at

the end of the manual.

Model Product Name

CL1308 8-Port PS/2-USB VGA Single Rail LCD KVM Switch

CL1316 16-Port PS/2-USB VGA Single Rail LCD KVM Swtich

CL1308 / CL1316 User Manual

iv

Conventions

This manual uses the following conventions:

Package Contents

The CL1308 / CL1316’s standard package consists of:

 1 CL1308 / CL1316 LCD KVM Switch

 1 power cord

 2 custom KVM cables

 1 firmware upgrade cable

 1 user instructions*

Check to make sure that all components are present and in working condition.

If you encounter a problem, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit, and/or any of the

devices connected to it.

* Features may have been added to the CL1308 / CL1316 since this manual

was released. Please visit our website to download the most up-to-date

version of the manual.

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

> Indicates selecting consecutive options (such as on a menu or

dialog box). For example, Start

>

Run means to open the Start

menu, and then select Run.

Indicates critical information.

CL1308 / CL1316 User Manual

v

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

International http://www.aten.com

North America http://www.aten-usa.com

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

CL1308 / CL1316 User Manual

vi

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

CL1308 / CL1316 User Manual

vii

Contents

Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Chapter 1.

Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 2.

Hardware Setup

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Before you Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Standard Rack Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Optional Rack Mount Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Single Level Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Cable Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Two Level Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 3.

Basic Operation

Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Powering Off and Restarting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

LCD OSD Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

The LCD Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

CL1308 / CL1316 User Manual

viii

LCD Adjustment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Manual Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 4.

OSD Operation

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

OSD Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

OSD Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Dedicated Invocation Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

OSD Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

F2: LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

F3: SET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Manufacturing Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

F5: SKP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

F6: BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

F8: LOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Chapter 5.

Keyboard Port Operation

Hotkey Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Invoke Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Dedicated Invocation Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Number Lock and Minus Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Control and F12 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Select the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Auto Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Invoking Auto Scan: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Skip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Computer Keyboard / Mouse Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Quick Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

OSD Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Port OS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Set USB Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Restore Default Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

CL1308 / CL1316 User Manual

ix

Hotkey Summary Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Chapter 6.

Keyboard Emulation

Mac Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Sun Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Chapter 7.

The Firmware Upgrade Utility

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . . 49

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Consignes de sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

CL1308 to Compatible 8-Port Switches . . . . . . . . . . . . . . . . . . . . . . . 65

CL1308 to Compatible 16-Port Switches . . . . . . . . . . . . . . . . . . . . . . 65

CL1316 to Compatible 8-Port Switches . . . . . . . . . . . . . . . . . . . . . . . 65

CL1316 to Compatible 16-Port Switches . . . . . . . . . . . . . . . . . . . . . . 65

Supported KVM Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

OSD Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

About SPHD Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

CL1308 / CL1316 User Manual

x

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

The CL1308 / CL1316 LCD KVM Switch features an integrated 19" LED-

backlit LCD panel and a keyboard and touchpad module for access and control

of up to 8 / 16 computers from a single, compact, 1U-design console (keyboard,

mouse, and monitor). As many as 8 (CL1308) / 16 (CL1316) additional

switches can be cascaded for controlling up to 128 (CL1308) / 256 (CL1316)

computers.

Setup is fast and easy — plugging cables into their appropriate ports is all that

is entailed, without requiring any software configuration. The switch supports

both USB and PS/2 interface computers. Switching between computers can be

easily accomplished either by manually pressing the front panel pushbuttons,

entering hotkey combinations from the keyboard, or via a menu-driven

multilingual on-screen display (OSD).

A convenient auto-scan feature permits automated monitoring of the activities

on all connected computers by alternating views between them at set intervals.

The CL1308 / CL1316 effectively eliminates the expense, space, and energy

needed for setting up a separate keyboard, monitor, and mouse for each

managed computer, and creates a greener environment by reducing energy

waste.

CL1308 / CL1316 User Manual

2

Features

 Exclusive LED illumination light — illuminates the keyboard and

touchpad for operation under low-light conditions

 A single console controls up to 128 (CL1308) / 256 (CL1316) computers

 Integrated KVM console with 19” LED-backlit LCD panel

 Cascade to 2 levels — connect up to 8 (CL1308) / 16 (CL1316) switches

 Dual interface — supports computers with PS/2 and USB keyboard and

mouse interfaces

 Multiplatform support — Windows, Linux, Mac, and Sun

 Supports USB keyboards for PC, Mac, and Sun

 Auto PS/2 and USB interface detection

 USB and PS/2 keyboard and mouse emulation — computers boot even

when the console focus is elsewhere

 Keyboard languages supported: English (US), English (UK), French,

German, German (Swiss), Greek, Hungarian, Italian, Japanese, Korean,

Russian, Spanish, Swedish, and Traditional Chinese

 Superior video quality — up to 1280 x 1024 @ 75 Hz; DDC2B

 Convenient computer switching via front panel pushbuttons, hotkeys, or

multilingual on-screen display (OSD) menu

 Two-level password security — only authorized users can view and

control the managed computers; up to four users and an administrator with

a separate profile for each

 Auto Scan feature for automated monitoring of user-selected computers

 Broadcast mode — the same operations simultaneously performed on all

selected computers

 Hot pluggable — add or remove computers without having to power down

the switch

 Buzzer on/off via hotkey and OSD

 Firmware upgradeable

 No software installation required

 Rack mountable

Chapter 1. Introduction

3

Requirements

Computers

The following hardware components are required for each computer:

 A VGA, SVGA, or multisync video graphics card with an HDB-15 port.

 PS/2 mouse and keyboard ports (6-pin Mini-DIN), or at least one USB

port.

Cables

Substandard cables might damage the connected devices or affect their overall

performance. For optimum signal integrity and simplified layout, use the high-

quality custom cable sets described below.

Operating Systems

:

Function Length Part Number

KVM switch to computer PS/2 1.2 m

1.8 m

3.0 m

6.0 m

1.8 m

2L-5201P

2L-5202P

2L-5203P

2L-5206P

2L-5702P

USB 1.2 m

1.8 m

3.0 m

5.0 m

2L-5201U

2L-5202U

2L-5203U

2L-5205U

OS Version

Windows 2000 or later

Linux RedHat 7.1 or later

SuSE 8.2 or later

Mandriva (Mandrake) 9.0 or later

UNIX AIX 4.3 or later

FreeBSD 4.2 or later

Sun Solaris 8 or later

Novell Netware 5.0 or later

Mac OS 9 or later

CL1308 / CL1316 User Manual

4

Components

Front View

Note: While it is the CL1316 that is pictured above, the CL1308 is identical

with the exception of only having 8 KVM ports.

11

12

13

14

10

3

4

5

6

7

9

8

2

1

2

EXIT I LIGHT

15

Chapter 1. Introduction

5

No. Component Description

1 handle Pull to slide the KVM module out; push to slide the module in

(see item 2 in this table).

2 slide release In order to slide the console out, you must first release it by

sliding these tabs to the inside. See page 15 for details on

sliding the console in and out.

3 LCD display After sliding the KVM module out, flip up the cover to access

the LCD monitor.

4 LCD controls The LCD On / Off switch is located here, as well as buttons to

control the position and picture settings of the LCD display.

See page 19 for details.

5 port LEDs An orange ON LINE LED lights to indicate that the computer

attached to its corresponding port is up and running. A green

Selected LED lights to indicate that the computer attached to

the corresponding port is selected for KVM control.

6 keyboard Standard 105-key keyboard

7 touchpad Standard mouse touchpad

8 port switches Press the port pushbuttons to bring the KVM focus to the

computer attached to the corresponding port.

9 power LED Lights to indicate that the unit is receiving power.

10 rack mount

brackets

The rack mount brackets located at each corner of the unit

secure the chassis to a system rack.

11 lock LEDs Num Lock, Caps Lock, Scroll Lock LEDs are located here.

12 reset button Located to the right of the Lock LEDs. Press this button in

with a small object to perform a system reset.

13 firmware

upgrade

section



Firmware upgrade port: The firmware upgrade cable that

transfers the firmware upgrade data from the administra-

tor's computer to the CL1308 / CL1316 plugs into this RJ-

11 connector.



Firmware upgrade switch: During normal operation this

switch should be in the NORMAL position. (See The Firm-

ware Upgrade Utility, page 47 for firmware upgrading

details.)

14 LED illumination

light

Illuminates the keyboard and touchpad to allow visibility in

low-light conditions.

15 exit / light

pushbutton

Press the exit / light pushbutton for two seconds to turn the

LED light on or off (default: on).

During the LCD OSD mode, this pushbutton has more

functions, refer to The LCD Buttons on page 19 for more

details.

CL1308 / CL1316 User Manual

6

Rear View

Note: The CL1316 is pictured above. The CL1308 rear panel is the same as

the CL1316, except that it has 8 KVM ports instead of 16.

No. Component Description

1 power socket This is a standard 3-prong AC power socket. The power cord

from an AC source plugs in here.

2 power switch This standard rocker switch powers the unit on and off.

3 KVM port section The cables that link to the computers plug in here.

Note: The shape of these SPHD connectors have been

specifically modified so that only KVM cables designed to

work with this switch can plug in (see the Cables section on

page 3, for details). Do NOT attempt to use ordinary 15 pin

VGA connector cables to link these ports to the computers.

4 grounding

terminal

The grounding wire used to ground the switch attaches here.

1

2

3

4

7

Chapter 2

Hardware Setup

Overview

The CL1308 / CL1316 is a switch designed to work with USB and PS/2

interfaces. It utilizes custom KVM cables that serve as the medium between the

switch and managed computers. A custom KVM cable is required for each

computer. Custom cables of various lengths are listed on

page 3. Consult your

dealer to find out which custom KVM cables best fit your needs.

Before you Begin

1. Important safety information regarding the placement of this

device is provided on page 53. Please review it before

proceeding.

2. Make sure the power to all devices to be connected has been

turned off. You must unplug the power cords of any computers

with Keyboard Power-On function.

CL1308 / CL1316 User Manual

8

Standard Rack Mount

A standard rack mount kit is provided with your CL1308 / CL1316 for

mounting it within a 1U rack space, with a depth of 52.0 - 85.0 cm. The

installation procedures are described in the following sections. Below is an

image of the parts included with your package that will be needed for rack

installation.

Note:  It takes two people to mount the console.

 The standard rack mount kit does not include screws or cage nuts.

If you need additional screws or cage nuts, contact your rack

dealer.

left & right L-shaped brackets

Chapter 2. Hardware Setup

9

To rack mount the CL1308 / CL1316, do the following:

1. Have one person position the unit onto the rack and hold it steady. Have a

second person screw the front brackets onto the rack.

2. While the first person still holds the unit in place, the second person slides

the left & right L-shaped brackets into the unit’s side mounting brackets

from the rear, installing four screws in the brackets to secure them in place.

3. After the L-shaped brackets are secured, tighten all the screws.

Allow at least 5.1 cm of clearance on each side for proper ventilation, and

at least 12.7 cm at the back for the power cord and cables.

CL1308 / CL1316 User Manual

10

Optional Rack Mount Kits

Optional rack mount kits are also available and listed in the table below:

Note:  For more information, visit the product webpage and refer to the

Compatible Accessories.

 For detailed installation steps, visit the product webpage and refer

to the Optional Rack Mount Kits Installation Guide.

Grounding

To prevent damage to your installation, it is important that all devices are

properly grounded. Use a grounding wire to ground the CL1308 / CL1316 by

connecting one end of the wire to the grounding terminal and the other end of

the wire to a suitable grounded object.

Mounting Kit Description

Standard Long Rack Mount

Kit

This kit is the long-railed version of your standard rack

mount kit that lets you fit your device to racks with

greater depth.

Easy Installation Rack

Mount Kit

This kit is designed to easily install the unit without

requiring more than one person

La page charge ...

ATEN CL1308N Manuel utilisateur

Ce manuel convient également à

ATEN CL1308N Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents