Hitachi DH 40FA Instruction And Safety Manual

Marque: Hitachi

Modèle: DH 40FA

Catégorie: Outils électroportatifs

Taper: Instruction And Safety Manual

DH 40FA

MODEL ROTARY HAMMER

MODÈLE MARTEAU ROTATIF

MODELO MARTILLO GIRATORIO

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant

qu’ils utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual before operating the power tool. Please keep this

manual available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de que utilicen la

herramienta eléctrica.

CONTENTS

Page

IMPORTANT INFORMATION ............ 3

MEANINGS OF SIGNAL WORDS ..... 3

SAFETY ...................................................... 4

GENERAL SAFETY RULES.................... 4

SPECIFIC SAFETY RULES AND

SYMBOLS........................................... 7

DOUBLE INSULATION FOR SAFER

OPERATION ....................................... 8

FUNCTIONAL DESCRIPTION.................... 9

MANE OF PARTS................................... 9

SPECIFICATIONS ................................... 9

Page

ASSEMBLY AND OPERATION ............... 10

APPLICATIONS .................................... 10

PRIOR TO OPERATION ....................... 10

HOW TO USE ....................................... 11

HOW TO USE THE CORE BIT ............. 13

MAINTENANCE AND INSPECTION ....... 15

ACCESSORIES ......................................... 17

STANDARD ACCESSORIES ................ 17

OPTIONAL ACCESSORIES.................. 17

PARTS LIST.............................................. 52

TABLE DES MATIERES

Page

INFORMATIONS IMPORTANTES ....... 19

SIGNIFICATION DES MOTS

D’AVERTISSEMENT ........................ 19

SECURITE ................................................ 20

REGLES GENERALES DE SECURITE

... 20

REGLES DE SECURITE SPECIFIQUES

ET SYMBOLES ................................. 23

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR ..... 24

DESCRIPTION FONCTIONNELLE ........... 25

NOM DES PARTIES ............................. 25

SPECIFICATIONS ................................. 25

Page

ASSEMBLAGE ET FONCTIONNEMENT ....

APPLICATIONS .................................... 26

AVANT L’UTILISATION ....................... 26

UTILISATION ....................................... 27

COMMENT UTILISER LA

COURONNE ..................................... 29

ENTRETIEN ET INSPECTION .................. 31

ACCESOIRES ........................................... 33

ACCESSOIRES STANDARD ................ 33

ACCESSOIRES SUR OPTION.............. 33

LISTA DES PIÈCES .................................. 52

ÍNDICE

Página

INFORMACIÓN IMPORTANTE ........... 35

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN................................ 35

SEGURIDAD............................................. 36

NORMAS GENERALES DE SEGURIDAD

.. 36

NORMAS Y SÍMBOLOS

ESPECÍFICOS DE SEGURIDAD ....... 39

AISLAMIENTO DOBLE PARA OFRECER

UNA OPERACIÓN MÁS SEGURA

.... 40

DESCRIPCIÓN FUNCIONAL.................... 41

NOMENCLATURA ............................... 41

ESPECIFICACIONES ............................ 41

Página

MONTAJE Y OPERACIÓN ...................... 42

APLICACIONES .................................... 42

ANTES DE LA OPERACIÓN ................ 42

MODE DE UTILIZACIÓN...................... 43

MODO DE USAR LA BARRENA

TUBULAR ......................................... 46

MANTENIMIENTO E INSPECCIÓN ........ 48

ACCESORIOS........................................... 50

ACCESORIOS ESTÁNDAR .................. 50

ACCESORIOS OPCIONALES............... 50

LISTA DE PIEZAS .................................... 52

English

Français

Español

English

IMPORTANT INFORMATION

Read and understand all of the operating instructions, safety precautions and

warnings in the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused

by the failure to observe basic safety rules or precautions. An accident can often be

avoided by recognizing a potentially hazardous situation before it occurs, and by

observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction

Manual and in the sections which contain the operation and maintenance

instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are

identified by WARNINGS on the power tool and in this Instruction Manual.

Never use this power tool in a manner that has not been specifically recommended

by HITACHI, unless you first confirm that the planned use will be safe for you and

others.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result

in serious personal injury.

CAUTION indicates a hazardous situations which, if ignored, could result in moderate

personal injury, or could cause machine damage.

NOTE emphasizes essential information.

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric

shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases, or dust. Power tools create sparks which may

ignite the dust or fumes.

(3) Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) Double Insulated tools are equipped with a polarized plug (one blade is wider

than the other.) This plug will fit in a polarized outlet only one way. If the

plug does not fit fully in the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician to install a polarized outlet. Do not change the

plug in any way. Double Insulation eliminates the need for the three wire

grounded power cord and grounded power supply system.

(2) Avoid body contact with grounded surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is

grounded.

(3) Don’t expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the plug

from a receptacle. Keep cord away from heat, oil, sharp edges or moving

parts. Replace damaged cords immediately. Damaged cords increase the

risk of electric shock.

(5) When operating a power tool outside, use an outdoor extension cord marked

“W-A” or “W”. These cords are rated for outdoor use and reduce the risk of

electric shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating

a power tool. Do not use tool while tired or under the influence of drugs,

alcohol, or medication. A moment of inattention while operating power tools

may result in serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

English

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying

tools with your finger on the switch or plugging in tools that have the switch

on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or

a key that is left attached to a rotating part of the tool may result in personal

injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing

and balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear protective glasses. Dust mask, non-skid

safety shoes, hard hat, or ear plugs must be used for appropriate conditions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a

stable platform. Holding the work by hand or against your body is unstable

and may lead to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool

will do the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be

controlled with the switch is dangerous and must be repaired.

(4) Disconnect the plug form the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools, with sharp cutting edges are less likely to bind and are

easier to control.

(7) Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tools operation. If damaged, have

the tool serviced before using. Many accidents are caused by poorly

maintained tools.

(8) Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool, may become hazardous

when used on another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of

injury.

(2) When servicing a tool, use only identical replacement parts. Follow

instructions in the Maintenance section of this manual. Use of unauthorized

parts or failure to follow Maintenance Instruction may create a risk of electric

shock or injury.

6. Never touch moving parts.

Never place your hands, fingers or other body parts near the tool’s moving parts.

7. Never operate without all guards in place.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or

safety feature, be sure to replace the guard or safety feature before resuming

operation of the tool.

English

8. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended — for example — don’t use circular saw

for cutting tree limbs or logs.

9. Never use a power tool for applications other than those specified.

Never use a power tool for applications other than those specified in the

Instruction Manual.

10.Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or

throw the tool. Never allow the tool to be operated by children, individuals

unfamiliar with its operation or unauthorized personnel.

11.Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition

periodically.

12.Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools

should not be used until repaired.

13.Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to yourself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

14.Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all

times. Check for dust build-up frequently.

15.Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may

burn out.

16.Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

17.Never leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

18.Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently,

it may be deformed, cracked, or damaged.

19.Do not wipe plastic parts with solvent.

Solvents such as gasolie, thinner, benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring or its own cord. Contact with a “live”

wire will make exposed metal parts of the tool “live” and shock the operator.

2. Wear ear plugs when using the tool for extended periods. Prolonged exposure

to high intensity noise can cause hearing loss.

3. NEVER touch the tool bit with bare hands after operation.

4. NEVER wear gloves made of stuff liable to roll up such as cotton, wool, cloth or

string, etc.

5. ALWAYS attach the side handle and securely grip the Rotary Hammer.

6. ALWAYS be careful with buried object such as an underground wiring.

Touching these active wiring or electric cable with this tool, you may receive an

electric shock.

Comfirm if there are any buried object such as electric cable within the wall,

floor or ceiling where you are going to operate here after.

7. Definitions for symbols used on this tool

V .............volts

Hz ...........hertz

A .............amperes

no ..........no load speed

W ............watt

............Class II Construction

---/min ....revolutions per minute

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation” means that two physically separated insulation systems

have been used to insulate the electrically conductive materials connected to the

power supply from the outer frame handled by the operator. Therefore, either the

symbol “ ” or the words and “Double insulation” appear on the power tool or on

the nameplate.

Although this system has no external grounding, you must still follow the normal

electrical safety precautions given in this Instruction Manual, including not using

the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble

this power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy

water, and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the

plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

English

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

Some illustrations in this Instruction Manual may show details or attachments

that differ from those on your own power tool.

NAME OF PARTS

Fig. 1

Housing

Stopper

Switch Trigger

Side Handle

Handle

Nameplate

Tail Cover

Set Screw

(Under the Tail Cover)

Selector Lever

Brush Cap

(Inside the Tail Cover)

SPECIFICATIONS

Motor Single-Phase, Series Commutator Motor.

Power Source Single-Phase, 115 V 60 Hz

Current 8.7 A

Capacity Drill Bit: 1-9/16" (40 mm)

Core Bit: 4-1/8" (105 mm)

No-Load Speed 400/min

Full-load Blow 2800 bpm

Weight 14.8 lbs (6.7 kg)

Tool Holder

English

ASSEMBLY AND OPERATION

APPLICATIONS

Rotation and hammering function

䡬 Drilling anchor holes

䡬 Drilling holes in concrete

Hammering function only

䡬 Crushing concrete, chipping, digging, and squaring

(by applying optional accessories)

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source

requirements specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a

receptacle while the switch is in the ON position, the power tool will start operating

immediately and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity (refer to page 9). The extension cord should

be kept as short as practicable.

WARNING: Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired.

Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious

hazard.

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

6. How to install dust cover (Fig. 2)

Always install the dust cover on the drill

bit or the taper shank adaptor. Insert the

dust cover until it lies flush in the

groove.

NOTE: For a thick drill bit, insert the

dust cover from drill rear.

Dust cover

Fig. 2

Insert up to the groove

English

7. How to install tool

CAUTION: For tools such as a drill bit and a bull point, use only Hitachi genuine

parts.

(1) Clean, then smear the tool shank with

the grease provided in the green tube.

(2) Pull the tool holder in the direction of

arrow 1 and rotate it in the direction of

arrow 2 (counterclockwise). Fully insert

the tool shank into the hexagonal hole

of the front cover. (Fig. 3)

(3) Return the tool holder to fix the tool.

NOTE: Remove in the reverse order to

installation.

HOW TO USE

1. How to drill holes (Fig. 4)

(1) Pull the switch trigger after applying the

drill bit tip to the drilling position.

(2) It is unnecessary to forcibly press the

rotary hammer main body. It is sufficient

to slightly press the rotary hammer to

an extent that clips are freely

discharged.

CAUTION:

Although this machine is equipped with

a safety clutch, if the drill bit becomes

bound in concrete or other material, the

resultant stoppage of the drill bit could

cause the machine body to turn in

reaction. Ensure that the main handle

and side handle are gripped firmly

during operation.

2. How to chisel or crush (Fig. 5)

By applying the tool tip to the chiseling

or crushing position, operate the rotary

hammer by utilizing its empty weight.

Forcible pressing or thrusting is

unnecessary.

Front Cover

Tool Shank

Fig. 3

Tool Holder

Fig. 4

Fig. 5

English

3. How to select rotation-hammering

and hammering.

(1) Rotation-hammering (Fig. 6)

Rotate the selector lever clockwise so

that the ▲ mark on the selector lever is

aligned with the ▲ mark on the side of

the mark on the under cover.

(2) Hammering (Fig. 7)

Rotate the selector lever counter-

clockwise so that the ▲ mark on the

selector lever is aligned with the ▲ mark

on the side of the mark on the under

cover.

CAUTION:

䡬 Turning the selector lever during motor

rotation will rotate the tool accidentally.

The selector lever should only be turned

when the motor is stopped.

4. Install the stopper (Fig. 8)

(1) Loosen the side handle and insert the

straight portion of the stopper into the

handle bolt hole from the front cover.

(2) Loosen the side handle, move the

stopper to the specified position and

rotate the grip of the side handle

clockwise to fix the stopper.

5. Warming up (Fig. 9)

The grease lubrication system in this

unit may require warming up in cold

regions.

Position the end of the bit so makes

contact with the concrete, turn on the

switch and perform the warming up

operation. Make sure that a hitting

sound is produced and then use the

unit.

CAUTION:

When the warming up operation is

performed, hold the side handle and the

main body securely with both hands to

maintain a secure grip and be careful

not to twist your body by the jammed

drill bit.

Fig. 6

Selector

Lever

Under Cover

▲

Fig. 7

Selector

Lever

Under Cover

▲

Fig. 8

Stopper

Side Handle

Fig. 9

English

6. How to use the drill bit (taper shank)

and the taper shank adaptor.

(1) Install drill bit with taper shank in the

taper shank adaptor.

(2) Turn the power on and drill a base hole.

(3) After cleaning out dust with a syringe,

attach the plug to the anchor tip and

drive in the anchor with a manual

hammer.

(4) To remove the drill bit with taper shank,

insert a cotter into the slot of the taper

shank adaptor, place supports under the

rotary hammer and tap the cotter with

a manual hammer. (Fig. 11)

HOW TO USE THE CORE BIT

When boring penetrating large hole use the

core bit. At that time use with the center

pin and the core bit shank provided as

optional accessories.

1. Mounting

CAUTION:

Be sure to turn power OFF and disconnect

the plug from the receptacle.

(1) Mount the core bit to the core bit shank.

(Fig. 12)

Lubricate the thread of the core bit

shank to facilitate disassembly.

(2) Mount the core bit shank to the rotary

hammer. (Fig. 13)

(3) Insert the center pin into the guide plate

until it stops.

(4) Engage the guide plate with the core bit,

and turn the guide plate to left or right

so that it does not fall even if it faces

downward. (Fig. 14)

Fig. 10

Drill Bit

(Taper shank)

Taper Shank Adaptor

Taper Shank

Adaptor

Cotter

Support

Fig. 11

Fig. 12

Core Bit

Shank

Fig. 13

English

2. How to bore (Fig. 15)

(1) Connect the plug to the receptacle.

(2) A spring is installed in the center pin.

Push it lightly to the wall or the floor

straight. Connect all over the surface of

the core bit tip and start operating.

(3) When boring about 3/16" (5 mm) in

depth the position of the hole will

establish. Bore after that removing the

center pin and the guide plate from core

bit.

(4) Application of excessive force will not

only expedite the work, but will

deteriorate the tip edge of the drill bit,

resulting in reduced service life of the

rotary hammer.

CAUTION:

When removing the center pin and the

guide plate, turn OFF the switch and

disconnect the plug from the

receptacle.

3. Dismounting (Fig. 16)

Remove the core bit shank from the

rotary hammer and strike the head of

the core bit shank strongly two or three

times with a manual hammer holding

the core bit, then the thread becomes

loose and the core bit can be removed.

Fig. 14

Center Pin

Core Bit

Core Bit Tip

Guide Plate

Fig. 15

Core Bit

Shank

Fig. 16

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency,

replace the drill bit with a new one or resharpening without delay when abrasion

is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that they are properly

tightened. Should any of the screws be loose, retighten them immediately.

WARNING: Using this rotary hammer with loosen screws is extremely

dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due care

to ensure the winding does not become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes: (Fig. 17)

The motor employs carbon brushes which are consumable parts. When they

become worn to or near “wear limit”, it could result in motor trouble. When an

auto-stop carbon brush is equipped, the motor will stop automatically. At that

time, replace both carbon brushes with new ones which have the same carbon

brush Nos. shown in the figure.

In addition, always keep carbon brushes clean and ensure that they slide freely

within the brush holders.

CAUTION: Using this rotary hammer with a carbon brush which is worn in

excess of the wear limit will damage the motor.

NOTE: Use HITACHI carbon brush No.73 indicated in Fig. 17

Wear limit

No. of carbon brush

0.28" (7 mm)

0.67" (17 mm)

Fig. 17

English

䡬 Replacing carbon brushes:

(For parts name, refer to Fig. 1)

Loosen the two set screws and remove the tail cover. Remove the brush caps

and carbon brushes. After replacing the carbon brushes, tighten the brush caps

securely and to install the tail cover with securely tightening two set screws.

5. How to replase grease

This machine is full air-tight construction to protect against dust and to prevent

lubricant leakage. Therefore, the machine can be used without lubrication for

long periods. Replace the grease as described below.

䡬 Grease replacement period

After purchase, replace grease after every 6 months of usage. Ask for grease

replacement at the nearest HITACHI Authorized Service Center. Proceed for

replacement of grease.

䡬 Grease replenishment

CAUTION: Before replenishing the grease, turn the power off and pull out the

power plug.

(1) Remove the crank case cover and wipe

off the grease inside.

(2) Apply 0.7 oz (20 g) of HITACHI Electric

Hammer Grease A (standard accessory,

contained in tube) to the crank case.

As the tube contains 1 oz (30 g) of

grease, supply 2/3 of the contained

grease.

(3) After replenishing the grease, install the

crank case securely.

NOTE: The HITACHI Electric Hammer

Grease A is of the lower

viscosity type. When the

supplied grease tube is

consumed, purchase from a

HITACHI Autorized Service

Center.

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts

because of wear from normal use. To assure that only authorized replacement

parts will be used, all service and repairs must be performed by a HITACHI

AUTHORIZED SERVICE CENTER, ONLY.

Crank Case Cover

Fig. 18

English

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction

Manual.

The use of any other attachment or accessory can be dangerous

and could cause injury or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) Case (Molded plastic) (Code No. 313097)............................................................. 1

(2) Side Handle (Code No. 313078)............................................................................. 1

(3) Stopper (Code No. 971786).................................................................................... 1

(4) Allen Wrench 4 mm (Code No. 944458)................................................................1

(5) Allen Wrench 5 mm (Code No. 944459)................................................................1

(6) Hammer Grease A (Code No. 981840) .................................................................. 1

(7) Dust Cover (Code No. 993245) .............................................................................. 1

OPTIONAL ACCESSORIES.....sold separately

For accessories in detail please call HITACHI AT 1-800-59-TOOLS

1. Through-hole drilling (Rotation + Hammering)

2. Anchor hole drilling (Rotation + Hammering)

Overall length

16" (400 mm)

Code No.

985374

985375

985376

External dia.

1/2" (12.7 mm)

1" (25.4 mm)

1-1/2" (38.1 mm)

(1) Drill bit

(Taper shank)

(3) Cotter (Code No. 944477)

(2) Taper shank adaptor

(Spline shank)

(1) Drill bit (Spline shank)

English

(2) Taper shank adaptor

3. Large-dia. hole boring (Rotation + Hammering)

4. Crushing (Hammering)

5. Groove digging and edging (Hammering)

6. Asphalt cutting (Hammering)

7. Digging

8. Syringe (for chip removal)

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

(Guide plate)

Code No.

985388

955169

(2) Core bit

External dia.

2" (50 mm)

4-1/8" (105 mm)

(1) Center pin

Code No.

955165

(3) Core bit shank

(Spline shank)

Taper shank adaptor formed

A-taper or B-taper is provided as

optional accessory, but drill bit for

it is not provided

Code No. 985377

Code No. 985378

A-taper

B-taper

(1) Bull point

Overall length Code No.

12" (300 mm) 985383

(1) Cold chisel

Overall length Code No.

12" (300 mm) 985381

18" (460 mm) 985382

(1) Cutter

Overall length Width Code No.

12" (300 mm)

1-1/2" (38 mm) 985384

2" (50 mm) 985385

(1) Scoop

Code No. 985386

Code No. 944575

Français

INFORMATIONS IMPORTANTES

Lire et comprendre toutes les instructions de fonctionnement, les précautions de

sécurité et les avertissements dans ce mode d’emploi avant d’utiliser ou d’entretenir

cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé

proviennent d’un non respect des règles ou précautions de base de sécurité. Un

accident peut la plupart du temps être évité si l’on reconnaît une situation de danger

potentiel avant qu’elle ne se produise, et en observant les procédures de sécurité

appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section

“SECURITE” de ce mode d’emploi et dans les sections qui contiennent les

instructions de fonctionnement et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un

endommagement de la machine sont identifiés par AVERTISSEMENTS sur l’outil

motorisé et dans ce mode d’emploi.

Ne jamais utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement

recommandée par HITACHI sans avoir d’abord vérifié que l’utilisation prévue est

sans danger pour vous et les autres.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles

sont ignorées, pourraient entraîner de sérieuses blessures personnelles.

PRECAUTION indique des situations dangereuses qui, si elles sont ignorées, pourrait

entraîner de légères blessures personnelles ou endommager la machine.

REMARQUE met en relief des informations essentielles.

Français

SECURITE

REGLES GENERALE DE SECURITE

AVERTISSEMENT: Lire et coxmprendre toutes les instructions.

Un non respect de toutes les instructions ci-dessous peut

entraîner une électrocution, un incendie et/ou de

sérieuses blessures personnelles.

CONSERVER CES INSTRUCTIONS

1. Zone de travail

(1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les

zones sombres invitent aux accidents.

(2) Ne pas utiliser les outils motorisés dans une atmosphère explosive, telle

qu’en présence de liquides inflammables, de gaz ou de poussières. Les outils

motorisés créent des étincelles qui risquent d’enflammer la poussière ou les

vapeurs.

(3) Tenir les spectateurs, les enfants et les visiteurs éloignés, lors de l’utilisation

de l’outil motorisé. Une distraction peut faire perdre le contrôle de la machine.

2. Sécurité électrique

(1) Les outils à double isolation sont équipés d’une fiche polarisée (une lame

est plus large que l’autre). Cette fiche ne pénétrera dans une prise secteur

polarisée que dans un sens. Si la fiche ne rentre pas complètement dans la

prise, la retourner. Si elle ne rentre toujours pas, contacter un électricien

qualifié pour installer une prise polarisée. Ne pas modifier la fiche d’aucune

façon. La double isolation élimine le besoin d’un cordon d’alimentation à

trois fils et d’un système d’alimentation avec mises à la terre.

(2) Eviter tout contact corporel avec les surfaces mises à la terre telles que les

canalisations, les radiateurs, les réchauds et les réfrigérateurs. Il y a un risque

accru d’électrocution si son corps est mis à la terre.

(3) Ne pas exposer les outils motorisés à la pluie ou à l’humidité. De l’eau

pénétrant à l’intérieur de l’outil motorisé augmente le risque d’électrocution.

(4) Ne pas maltraiter le cordon d’alimentation. Ne jamais utiliser le cordon pour

porter les outils ou tirer sur la fiche du réceptacle. Garder le cordon à l’écart

de la chaleur, de l’huile, des arêtes coupantes ou des pièces en mouvement.

Remplacer les cordons endommagés immédiatement. Des cordons

endommagés augmentent le risque d’électrocution.

(5) Lors de l’utilisation d’un outil motorisé, utiliser un cordon de rallonge

extérieur marqué “W-A” ou “W”. Ces cordons sont prévus pour une utilisation

extérieure et réduisent les risques d’électrocution.

3. Sécurité personnelle

(1) Rester sur ses gardes, regarder ce que l’on fait et utiliser son sens commun

lors de l’utilisation d’un outil motorisé. Ne pas utiliser un outil en état de

fatigue ou sous l’influence de drogues, d’alcool ou de médicaments. Un

moment d’inattention lors de l’utilisation de l’outil motorisé peut entraîner

de sérieuses blessures personnelles.

La page charge ...

Hitachi DH 40FA Instruction And Safety Manual

Marque: Hitachi

Modèle: DH 40FA

Catégorie: Outils électroportatifs

Taper: Instruction And Safety Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi DH 40FA
español: Hitachi DH 40FA

Documents connexes

Autres documents

Hikoki DH38YE2 Manuel utilisateur