Electrolux ESI64060X Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
user manual
notice d'utilisation
Dishwasher
Lave-vaisselle
ESI64060
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety information 2
Product description 3
Control panel 4
Use of the appliance 5
Setting the water softener 5
Use of dishwasher salt 6
Use of rinse aid 7
Loading cutlery and dishes 8
Use of detergent 10
Multitab function 11
Select and start a washing programme
12
Washing programmes 13
Care and cleaning 14
What to do if… 15
Technical data 16
Installation 17
Water connection 17
Electrical connection 18
Environment concerns 18
Subject to change without notice
SAFETY INFORMATION
For your safety and correct operation
of the appliance, read this manual
carefully before installation and use. Al-
ways keep these instructions with the
appliance even if you move or sell it.
Users must fully know the operation
and safety features of the appliance.
Correct use
• The appliance is designed exclusively for
domestic use.
• Only use the appliance to clean house-
hold utensils that are applicable for dish-
washers.
• Do not put solvents in the appliance. Risk
of explosion.
• Put the knives and all items with sharp
points in the cutlery basket with their
points down. If not, put in a horizontal
position in the upper basket.
• Use only branded products for dishwash-
ers (detergent, salt, rinse aid).
• If you open the door while the appliance
is in operation, hot steam can escape.
Risk of skin burns.
• Do not remove dishes from the dish-
washer before the end of the washing
programme.
• When the washing programme is com-
pleted, disconnect the mains plug from
the mains socket and close the water
tap.
• Only an authorised service engineer can
repair this appliance. Use only original
spare parts.
• Do not do repairs yourself to prevent in-
jury and damage to the appliance. Al-
ways contact your local Service Force
Centre.
General safety
• Persons (including children) with reduced
physical sensory, mental capabilities or
lack of experience and knowledge must
not use the appliance. They must have
supervision or instruction for the opera-
tion of the appliance by a person respon-
sible for their safety.
• Obey the safety instructions from the
manufacturer of the dishwasher deter-
gent to prevent burns to eyes, mouth and
throat.
• Do not drink the water from the dish-
washer. Detergent residues can stay in
your appliance.
• Always close the door when you do not
use the appliance to prevent injury and
not to stumble over the open door.
• Do not sit or stand on the open door.
Child safety
• Only adults can use this appliance. Chil-
dren must get supervision to make sure
that they do not play with the appliance.
• Keep all the packaging away from chil-
dren. There is a risk of suffocation.
2 electrolux
• Keep all detergents in a safe area. Do not
let children touch the detergents.
• Keep children away from the appliance
when the door is open.
Installation
• Make sure that the appliance is not dam-
aged because of transport. Do not con-
nect a damaged appliance. If necessary,
contact the supplier.
• Remove all packaging before first use.
• A qualified and competent person must
do the electrical installation.
• A qualified and competent person must
do the plumbing installation.
• Do not change the specifications or mod-
ify this product. Risk of injury and dam-
age to the appliance.
• Do not use the appliance:
– if the mains cable or water hoses are
damaged,
– if the control panel, worktop or plinth
area are damaged, that you can get
access to the inner side of the appli-
ance.
Contact your local Service Force Centre.
• Do not drill into the sides of the appliance
to prevent damage to hydraulic and elec-
trical components.
Warning! Carefully obey the
instructions for electrical and water
connections.
PRODUCT DESCRIPTION
1 Upper basket
2 Water hardness dial
3 Salt container
4 Detergent dispenser
5 Rinse aid dispenser
6 Rating plate
7 Filters
8 Lower spray arm
9 Upper spray arm
electrolux 3
CONTROL PANEL
1 2 3 4
6 578
1 Programme knob
2 Start/cancel button (Start/Cancel)
3 Multitab button (Multitab)
4 Delay start button (Delay)
5 Digital display
6 Indicator lights
7 Programme marker
8 Off position
Indicator lights
Wash phase Comes on when the washing phase or the rinsing phase operates.
Dry phase Comes on when the drying phase operates.
Multitab Comes on when you activate the multitab function Refer to 'Multitab func-
tion'.
Salt
1)
Comes on when it is necessary to fill the salt container. Refer to 'Use of
dishwasher salt'.
After you fill the container, the salt indicator light can continue to stay on
for some hours. This does not have an unwanted effect on the operation of
the appliance.
Rinse aid
1)
Comes on when it is necessary to fill the rinse aid container. Refer to 'Use
of rinse aid'.
1) When the salt and/or rinse aid containers are empty, the related indicator lights do not come on while a washing
programme operates.
Programme knob
• To switch on the appliance or to set a
washing programme, turn the pro-
gramme knob clockwise or counterclock-
wise. The programme marker on the pro-
gramme knob must agree with one of the
washing programmes on the control pan-
el. If the programme marker agrees with
a washing programme, the digital display
shows the time duration of the pro-
gramme. If the programme marker does
not agree with a washing programme,
the digital display shows two horizontal
bars.
• To switch off the appliance, turn the pro-
gramme knob until the programme mark-
er agrees with the off indicator.
Use the programme knob for these opera-
tions:
– To set the water softener. Refer to 'Set-
ting the water softener'.
4 electrolux
– To deactivate/activate the rinse aid dis-
penser. Refer to 'Multitab function'.
Start/cancel button
Use the start/cancel button for these opera-
tions:
• To start the washing programme. Refer
to the chapter 'Setting and starting a
washing programme'.
• To cancel a washing programme in pro-
gress. Refer to the chapter 'Setting and
starting a washing programme'.
• To set the water softener level. Refer to
the chapter 'Set the water softener'.
• To deactivate/activate the rinse aid dis-
penser. Refer to the chapter 'Multitab
function'.
Multitab button
Press this button to activate/deactivate the
multitab function. Refer to the chapter 'Mul-
titab function'.
Delay start button
Use the delay start button to delay the start
of the washing programme with an interval
between 1 and 19 hours. Refer to the
chapter 'Setting and starting a washing
programme'.
Digital display
The display shows:
• Adjusted level of the water softener.
• Activation/deactivation of the rinse aid
dispenser (only with multitab function on).
• Programme duration.
• Remaining time to the end of the pro-
gramme.
• End of a washing programme, the digital
display shows a zero.
• Number of hours in delay start.
• Fault codes.
Setting mode
The appliance is in setting mode when:
• One or more phase indicator lights are
on.
• The time duration of the programme
flashes in the digital display.
The appliance must be in setting mode for
these operations:
– To set a washing programme.
– To set the water softener level.
– To deactivate/activate the rinse aid dis-
penser.
The appliance is not in setting mode when:
• One or more phase indicator lights are
on.
• The time duration of the programme
does not flash.
In this condition cancel the programme to
go back to the setting mode. Refer to the
chapter 'Setting and starting a washing
programme'.
USE OF THE APPLIANCE
Refer to the following instructions for each
step of procedure:
1. Make a check if the water softener level
is correct for the water hardness in your
area. If necessary set the water soften-
er.
2. Fill the salt container with dishwasher
salt.
3. Fill the rinse aid dispenser with rinse aid.
4. Load cutlery and dishes into the dish-
washer.
5. Set the correct washing programme for
the type of load and soil.
6. Fill the detergent dispenser with the cor-
rect quantity of detergent.
7. Start the washing programme.
If you use combi detergent tablets ('3 in
1', '4 in 1', '5 in 1', etc.), refer to the
chapter 'Multitab function'.
SETTING THE WATER SOFTENER
The water softener removes minerals and
salts from the water supply. Minerals and
salts can have bad effect on the operation
of the appliance.
Water hardness is measured in equivalent
scales:
• German degrees (dH°).
• French degrees (°TH).
electrolux 5
• mmol/l (millimol per litre - international
unit for the hardness of water).
•Clarke.
Adjust the water softener to the water hard-
ness in your area. If necessary, contact
your local water authority.
Water hardness Water hardness setting
°dH °TH mmol/l Clarke manually electronically
51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10
43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9
37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8
29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7
23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6
19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5
15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4
11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3
4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2
< 4 < 7 < 0,7 < 5
1
1)
1
1)
1) No use of salt required.
You must set the water softener man-
ually and electronically.
Manual adjustment
The appliance is set at the factory at
position 2.
1. Open the door.
2. Remove the lower basket.
3. Turn the water hardness dial to position
1 or 2 (refer to the chart).
4. Install the lower basket.
5. Close the door.
Electronic adjustment
The water softener is set at the factory
at level 5.
The appliance must be switched off.
1. Press and hold the start/cancel button.
Turn the programme knob counter-
clockwise until the programme marker
agrees with the first washing pro-
gramme on the control panel.
2. Release the start/cancel button when
the digital display shows the current set-
ting.
Examples:
–
level 5 =
–
level 10 =
3. Press the start/cancel button to change
the water softener level. Every time you
press the button, the level increases.
4. Turn the programme knob to the off po-
sition to save the operation.
USE OF DISHWASHER SALT
Caution! Only use dishwashers salt.
Types of salt that are not applicable for
dishwashers cause damage to the
water softener.
Caution! Grains of salt and salty water
on the bottom of the appliance can
cause corrosion. Fill the appliance with
salt before you start a washing
programme to prevent corrosion.
Do these steps to fill the salt container:
1. Turn the cap anticlockwise to open the
salt container.
2. Fill the salt container with 1 litre of water
(only the first operation).
6 electrolux
3. Use the funnel to fill the salt container
with salt.
4. Remove the salt around the opening of
the salt container.
5. Turn the cap clockwise to close the salt
container.
It is normal that water overflows from
the salt container when you fill it with
salt.
When you set electronically the water soft-
ener to level 1, the salt indicator light does
not stay on.
USE OF RINSE AID
Caution! Only use branded rinse aid
for dishwashers.
Do not fill the rinse aid dispenser with
other products (e.g. dishwasher clean-
ing agent, liquid detergent). This can
cause damage to the appliance.
Rinse aid makes it possible to dry the
dishes without streaks and stains.
Rinse aid is automatically added during
the last rinsing phase.
Do these steps to fill the rinse aid dispens-
er:
1. Press the release button (A) to open the
rinse aid dispenser.
2. Fill the rinse aid dispenser with rinse aid.
The mark 'max.' shows the maximum
level.
3. Remove the spilled rinse aid with an ab-
sorbent cloth to prevent too much foam
during the subsequent washing pro-
gramme.
4. Close the rinse aid dispenser.
Adjusting the rinse aid dosage
The rinse aid is set at the factory at position
4.
You can set the rinse aid dosage between
position 1 (lowest dosage) and position 6
(highest dosage).
electrolux 7
1. Turn the rinse aid dial to increase or de-
crease the dosage.
– Increase the dosage if there are water
droplets or limescale on the dishes.
– Decrease the dosage if there are
streaks, whitish stains or bluish layers
on the dishes.
LOADING CUTLERY AND DISHES
Helpful hints and tips
Caution! Only use the appliance for
household utensils that are applicable
for dishwashers.
Do not use the appliance to clean objects
that can absorb water (sponges, household
cloths, etc.).
• Before you load cutlery and dishes, do
these steps:
– Remove all food remainings and deb-
ris.
– Make burnt, remaining food in pans
soft.
• While you load cutlery and dishes, do
these steps:
– Load hollow items (e.g. cups, glasses
and pans) with the opening down.
– Make sure that water does not collect
in the container or in a deep base.
– Make sure that cutlery and dishes do
not lie inside one another.
– Make sure that cutlery and dishes do
not cover other cutlery and dishes.
– Make sure that glasses do not touch
other glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick
coatings can keep water droplets. Plastic
items do not dry as well as porcelain and
steel items.
• Put light items in the upper basket. Make
sure that the items do not move.
Caution! Make sure that the spray
arms can move freely before you start
a washing programme.
Warning! Always close the door after
you load or unload the appliance. An
open door can be dangerous.
Lower basket
Put saucepans, lids, plates, salad bowls
and cutlery in the lower basket. Arrange
service dishes and large lids around the
edge of the basket.
8 electrolux
The rows of prongs in the lower basket can
be flat to load pots, pans and bowls.
Cutlery basket
Warning! Do not put long-bladed
knives in a vertical position. Arrange
long and sharp cutlery horizontally in
the upper basket. Be careful with sharp
items.
Put forks and spoons with the handles
down.
Put knives with the handles up.
Mix spoons with other cutlery to prevent
them to bond together.
Use the cutlery grid. If the dimensions of the
cutlery prevent the use of the cutlery grid,
you can remove it.
Upper basket
The upper basket is for plates (maximum
24 cm in diameter), saucers, salad bowls,
cups, glasses, pots and lids. Arrange the
items to let water touch all surfaces.
Prevent to put plates in the first three
sectors in the front part of the basket.
Make sure the plates tilt forward.
Put glasses with long stems in the cup
racks with the stems up. For longer items,
fold the cup racks up.
electrolux 9
Adjustment of the height of the upper
basket
If you put large plates in the lower basket,
first move the upper basket to the upper
position.
Maximum height of the dishes
upper bas-
ket
lower
basket
Upper position 20 cm 31 cm
Lower position 24 cm 27 cm
Do these steps to move the upper basket
to the upper position:
1. Pull the basket out until it stops.
2. Carefully lift the two sides until the
mechanism is engaged and the basket
is stable.
Do these steps to move the upper basket
to the lower position:
1. Pull the basket out until it stops.
2. Carefully lift the two sides upwards.
3. Hold the mechanism and let it fall back
down slowly.
Caution!
• Do not lift or lower the basket on one
side only.
• If the basket is in the upper position,
do not put cups on the cup racks.
USE OF DETERGENT
Only use detergents (powder, liquid or
tablet) that are applicable for dishwash-
ers.
Follow the data on the packaging:
• Dosage recommended by the manu-
facturer.
• Storage recommendations.
Do not use more than the correct
quantity of detergent to save an envi-
ronment.
Do these steps to fill the detergent dispens-
er:
1. Open the lid of the detergent dispenser.
2. Fill the detergent dispenser (A) with de-
tergent. The marking shows the dosage:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent.
3. If you use a washing programme with
prewash phase, put more detergent in
the prewash detergent compartment
(B).
10 electrolux
A
B
4. If you use detergent tablets, put the de-
tergent tablet in the detergent dispenser
(A).
5. Close the lid of the detergent dispenser.
Press the lid until it locks into position.
Different brands of detergent dissolve
in different times. Some detergent tab-
lets do not have the best cleaning re-
sults during short washing pro-
grammes. Use long washing pro-
grammes when you use detergent tab-
lets to fully remove the detergent.
MULTITAB FUNCTION
The multitab function is for combi detergent
tablets.
These tablets contain agents such as deter-
gent, rinse aid and dishwasher salt. Some
types of tablets can contain other agents.
Do a check if these tablets are applicable
for the local water hardness. Refer to the in-
structions from the manufacturer.
When you set the multitab function, it stays
on until you deactivate it.
The multitab function stops automatically
the flow of rinse aid and salt. The rinse aid
indicator light and salt indicator light are de-
activated.
The programme duration can increase if
you use the multitab function.
Activate or deactivate the multitab
function before the start of a washing
programme.
You cannot activate or deactivate the
multitab function when the programme
operates. Cancel the washing pro-
gramme, then set the programme
again.
To activate the multitab function:
• Press the multitab button. The multitab
indicator light comes on.
To deactivate the multitab function:
• Press the multitab button. The multitab
indicator light goes off.
Do these steps if the drying results
are not satisfactory:
1. Fill the rinse aid dispenser with rinse
aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to position
2.
• You can only activate or deactivate
the rinse aid dispenser when the
multitab function is activated.
To activate/deactivate the rinse aid dis-
penser:
The appliance must be switched off.
1. Turn the programme knob counter-
clockwise until the programme marker
agrees with the second washing pro-
gramme on the control panel.
electrolux 11
2. The digital display shows the current
setting for the rinse aid dispenser.
Rinse aid dispenser
deactivated
Rinse aid dispenser
activated
3. Press the start/cancel button to change
the setting. The digital display shows
the new setting.
4. Turn the programme knob to the off po-
sition to save the operation.
To use normal detergent again:
1. Deactivate the multitab function.
2. Fill the salt container and rinse aid
dispenser.
3. Adjust the water hardness setting
to the highest level.
4. Do a washing programme without
dishes.
5. Adjust the water softener to the wa-
ter hardness in your area.
6. Adjust the rinse aid dosage.
SELECT AND START A WASHING PROGRAMME
Do these steps to set and start a washing
programme:
1. Close the door.
2. Turn the programme knob to set the
washing programme. Refer to the chap-
ter 'Washing programmes'.
– The phase indicator light or lights for
the washing programme come on.
– The programme duration in the digital
display flashes.
3. Press the start/cancel button.
– The washing programme starts auto-
matically.
– When the programme starts, only the
indicator light of the phase in pro-
gress stays on. Programme duration
is on with a static light.
When the washing programme oper-
ates, you cannot change the pro-
gramme. Cancel the washing pro-
gramme.
Warning! Only interrupt or cancel a
washing programme if necessary.
Caution! Open the door carefully. Hot
steam can come free.
Interrupting a washing programme
Open the door.
• The programme stops.
Close the door.
• The programme continues from the point
of interruption.
Cancelling a washing programme
•Press and hold the start/cancel button.
– In the digital display the time duration
of the programme flashes.
– One or more phase indicator lights are
on.
The washing programme is cancelled.
At this time you can do these steps:
1. Switch off the appliance.
2. Set a new washing programme.
Fill the detergent dispenser with deter-
gent before you set a new washing pro-
gramme.
Setting and starting a washing
programme with delay start
1. Set a washing programme.
2. Press the delay start button until the dis-
play shows the necessary delay start
time for the washing programme. Delay
start time flashes in the digital display.
3. Press the start/cancel button.
– The countdown of the delay start
starts.
– The phase indicator lights of the
washing programme go off.
– In the digital display the delay start
time is on with a static light.
When the countdown is completed, the
washing programme automatically starts
The phase indicator light of the phase in
progress comes on.
Do not open the door during the count-
down to prevent interruption of the
countdown. When you close the door
again, the countdown continues from
the point of interruption.
Cancelling a delay start
1. Press and hold the start/cancel button.
– The phase indicator lights or light
come on.
12 electrolux
– In the digital display, the time duration
of the washing programme comes
on.
2. Press the start/cancel button to start the
washing programme.
End of the washing programme
Switch off the appliance in these condi-
tions:
• The appliance stops automatically.
• The digital display shows a zero.
• The phase indicator lights are off.
For better drying results, keep the door ajar
for some minutes before you remove the
dishes.
Let the dishes cool down before you re-
move them from the appliance. Hot dishes
are easily damaged.
Standby mode
If you do not switch off the appliance at the
end of the washing programme, the appli-
ance automatically goes into standby
mode. The standby mode decreases ener-
gy consumption.
Three minutes after the end of the pro-
gramme, all indicator lights go off and the
digital display shows one horizontal bar.
Press a button to go back to the end-of-
programme mode.
WASHING PROGRAMMES
Washing programmes
Programme
and pro-
gramme knob
position
Degree of soil Type of load Programme description
1)
Any Crockery, cutlery,
pots and pans
Prewash
Main wash up to 45°C or 70°C
1 or 2 intermediate rinses
Final rinse
Drying
2)
Normal or light soil Crockery and cutlery Main wash up to 60°C
Final rinse
Heavy soil Crockery, cutlery,
pots and pans
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
3)
Normal soil Crockery and cutlery Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
Any Partial load (to be
completed later in the
day).
1 cold rinse (to prevent food
scraps to bond).
Detergent is not necessary with
this programme.
1) During the AUTO programme, the soil level of the dishes is given by how cloudy the water is. The programme
duration and consumptions can change. This depends if the appliance is fully or not and on the level of soil on the
dishes. The appliance adjusts automatically the temperature of the water during the main wash.
2) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to load
breakfast and dinner crockery and cutlery.
3) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.
electrolux 13
Consumption values
Programme
Duration (in minutes)
1)
Energy (in kWh) Water (in litres)
- 1,1-1,7 11-22
- 0,9 9
- 1,8-2,0 22-24
- 1,0-1,1 13-15
- 0,1 4
1) The digital display shows the programme duration.
The pressure and temperature of the
water, the variations of power supply
and the quantity of dishes can change
these values.
CARE AND CLEANING
Warning! Switch the appliance off
before you clean the filters.
Cleaning the filters
Caution! Do not use the appliance
without the filters. Make sure that the
installation of the filters is correct.
Incorrect installation will cause
unsatisfactory washing results and
damage to the appliance.
If necessary, clean the filters. Dirty filters de-
crease the washing results.
The dishwasher has three filters:
1. coarse filter (A)
2. microfilter (B)
3. flat filter (C)
A
B
C
A
B
C
Do these steps to clean the filters:
1. Open the door.
2. Remove the lower basket.
3. To unlock the filter system, turn the
handle on the microfilter (B) approxi-
mately 1/4 anticlockwise.
4. Remove the filter system.
5. Hold the coarse filter (A) by the handle
with the hole.
6. Remove the coarse filter (A) from the
microfilter (B).
7. Remove the flat filter (C) from the bot-
tom of the appliance.
D
8. Clean the filters below running water.
9. Put the flat filter (C) in the bottom of the
appliance. Install the flat filter correctly
under the two guide (D).
10. Put the coarse filter (A) in the microfilter
(B) and push the filters together.
14 electrolux
11. Put the filter system in position.
12. To lock the filter system, turn the han-
dle on the microfilter (B) clockwise until
it lock in position.
13. Install the lower basket.
14. Close the door.
Do not remove the spray arms.
If the holes in the spray arms become clog-
ged, remove remaining parts of soil with a
cocktail stick.
External cleaning
Clean the external surfaces of the appliance
and control panel with a damp soft cloth.
Only use neutral detergents. Do not use
abrasive products, scouring pads or sol-
vents (acetone, trichloroethylene etc...).
Frost precautions
Caution! Do not install the appliance
where the temperature is below 0 °C.
The manufacturer is not responsible for
damage because of frost.
If not possible, empty the appliance and
close the door. Disconnect the water inlet
hose and remove water from the water inlet
hose.
WHAT TO DO IF…
The appliance does not start or stops dur-
ing operation.
If there is a fault, first try to find a solution to
the problem yourself. If you cannot find a
solution to the problem yourself, contact
the Service Force Centre.
Caution! Switch off the appliance
before you do the below suggested
corrective actions.
Fault code and malfunction Possible cause and solution
•
the digital display shows
The dishwasher does not fill with
water
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is closed.
Open the water tap.
• The filter in the water inlet hose is blocked.
Clean the filter.
• The connection of the water inlet hose is not correct. The
hose can be kinked or squashed.
Make sure that the connection is correct.
•
the digital display shows
The dishwasher will not drain
• There is a blockage in the sink spigot.
Clean the sink spigot.
• The connection of the water drain hose is not correct. The
hose can be kinked or squashed.
Make sure that the connection is correct.
•
the digital display shows
The anti-flood device operates
• Close the water tap and contact your local Service Force
Centre.
electrolux 15
Fault code and malfunction Possible cause and solution
The programme does not start • The appliance door is not closed.
Close the door.
• Mains plug is not connected in.
Put in the mains.
• The fuse has blown out in the household fuse box.
Replace the fuse.
• Delay start is set.
Cancel the delay start to start the programme immediately.
After the check, switch on the appliance.
Set the knob on the same washing pro-
gramme as before the malfunction.
The programme continues from the point of
interruption. If the malfunction shows again,
contact your Service Force Centre.
If the display shows a fault code, not de-
scribed in the chart, contact your Service
Force Centre.
These data are necessary to help you
quickly and correctly:
• Model (Mod.)
• Product number (PNC)
• Serial number (S.N.)
For these data, refer to the rating plate.
Write the necessary data here:
Model description : ..........
Product number : ..........
Serial number : ..........
The cleaning results are not satisfactory
The dishes are not clean • The selected washing programme is not applicable for the type of
load and soil.
• The baskets are loaded incorrectly so that water cannot reach all
surfaces.
• Spray arms do not turn freely because of incorrect arrangement of
the load.
• The filters are dirty or not correctly installed.
• The quantity of detergent is too little or missing.
Limescales particles on the
dishes
• The salt container is empty.
• The water softener is adjusted on a wrong level.
• The salt container cap is not closed correctly.
The dishes are wet and dull • No rinse aid has been used.
• The rinse aid dispenser is empty.
There are streaks, milky
spots or a bluish coating on
glasses and dishes
• Decrease the rinse aid dosage.
Dry water drop signs on
glasses and dishes
• Increase rinse aid dosage.
• The detergent can be the cause.
TECHNICAL DATA
Dimensions Width cm 59,6
Height cm 81,8 - 87,8
Depth cm 57,5
Electrical connection -
Voltage - Overall power -
Fuse
Information on the electrical connection is given on the rating plate on
the inner edge of the dishwasher door.
Water supply pressure Minimum 0,5 bar (0,05 MPa)
Maximum 8 bar (0,8 MPa)
Capacity Place settings 12
16 electrolux
INSTALLATION
Warning! Make sure that mains plug is
disconnected from the mains socket
during installation.
Important! Obey the instructions in the
enclosed template to:
• Build-in the appliance.
• Install the furniture panel.
• Connect to the water supply and drain.
Install the appliance under a counter (kitch-
en worktop or sink).
If a repair is necessary, the appliance must
be easily accessible for the engineer.
Put the appliance adjacent to a water tap
and a drain.
For the venting of the dishwasher only wa-
ter fill, water drain and power supply cable
openings are necessary.
The dishwasher has adjustable feet to allow
the adjustment of the height.
Make sure that the water inlet hose, the
drain hose and the supply cable are not
kinked or squashed, when you insert the
machine.
Attaching the appliance to the adjacent
units
Make sure that the counter below which
you attach the appliance is a safe structure
(adjacent kitchen units, cabinets, wall).
Adjusting the level of the appliance
Make sure that the appliance is level to
close and seal the door correctly. If the level
of the appliance is correct, the door does
not catch on the sides of the cabinet. If the
door does not close correctly, loosen or
tighten the adjustable feet until the appli-
ance is level.
WATER CONNECTION
Water inlet hose
Connected the appliance to a hot (max.
60°) or cold water supply.
If the hot water comes from alternative
sources of energy that are more environ-
mentally friendly (e.g. solar or photovoltaic
panels and aeolian), use a hot water supply
to decrease energy consumption.
Connect the inlet hose to a water tap with
an external thread of 3/4”.
Caution! Do not use connection hoses
from an old appliance.
The water pressure must be in the limits (re-
fer to 'Technical data'). Make sure that the
local water authority gives you the average
mains pressure in your area.
Make sure that there are no kinks in the
water inlet hose and that the water inlet
hose is not squashed or entangled.
Fit the locknut correctly to prevent water
leaks.
Caution! Do not connect the appliance
to new pipes or pipes that are not used
for a long time. Let the water run for
some minutes, then connect the inlet
hose.
Water drain hose
1. Connect the water drain hose to the
sink spigot and attach it under the work
surface. This prevents that the waste
water from the sink goes back into the
appliance.
2. Connect the water drain hose to a stand
pipe with vent-hole (minimum internal di-
ameter 4 cm).
max 85 cm
min 40 cm
max 400 cm
Make sure that the drain hose is not bent or
squashed to prevent that the water drains
does not drain correctly.
Remove the sink plug when the appliance
drains the water to prevent that the water
goes back into the appliance.
electrolux 17
A drain hose extension must not be longer
than 2 m. The internal diameter must not be
smaller than the diameter of the hose.
If you connect the water drain hose to a
trap spigot under the sink, remove the plas-
tic membrane (A). If you do not remove the
membrane, remaining food can cause a
blockage in the drain hose spigot
The appliance has a security feature to
prevent that dirty water goes back into
the appliance. If, the spigot of the sink
has a 'non-return valve', this valve can
cause the appliance to drain incorrect-
ly. Remove the non-return valve.
Caution! Make sure that the water
couplings are tight to prevent water
leakage.
ELECTRICAL CONNECTION
Warning! The manufacturer is not
responsible if you do not follow these
safety precautions.
This appliance needs to be earthed ac-
cording to safety precautions.
Make sure that the rated voltage and
type of power on the rating plate agree
with the voltage and the power of the
local power supply.
Always use a correctly installed shock-
proof socket.
Do not use multi-way plugs, connec-
tors and extension cables. There is a
risk of fire.
Do not replace the mains cable your-
self. Contact the Service Force Centre.
Make sure that the mains plug is ac-
cessible after installation.
Do not pull the mains cable to discon-
nect the appliance. Always pull the
mains plug.
ENVIRONMENT CONCERNS
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local council, your household
waste disposal service or the shop where
you purchased the product.
The packaging materials are environmental-
ly friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Discard the packaging
materials in the applicable container at the
community waste disposal facilities.
Warning! To discard the appliance,
follow the procedure:
• Pull the mains plug out of the socket.
• Cut off the mains cable and mains
plug and discard them.
• Discard the door catch. This pre-
vents the children to close them-
selves inside the appliance and en-
danger their lives.
18 electrolux
Electrolux. Thinking of you.
Partagez notre imagination sur www.electrolux.com
SOMMAIRE
Consignes de sécurité 20
Description de l'appareil 22
Bandeau de commande 22
Utilisation de l'appareil 24
Réglage de l'adoucisseur d'eau 24
Utilisation du sel régénérant 25
Utilisation du liquide de rinçage 26
Rangement des couverts et de la vaisselle
27
Utilisation du produit de lavage 29
Fonction "Tout en 1" 30
Sélection et départ d'un programme de
lavage 32
Programmes de lavage 33
Entretien et nettoyage 34
En cas d'anomalie de fonctionnement 35
Caractéristiques techniques 36
Installation 37
Raccordement à l'arrivée d'eau 37
Branchement électrique 38
En matière de protection de
l'environnement 38
Sous réserve de modifications
Lors de sa fabrication, cet appareil a été
construit selon des normes, directives et/ou
décrets pour une utilisation sur le territoire
français.
Pour la sécurité des biens et des per-
sonnes ainsi que pour le respect de
l'environnement, vous devez d'abord li-
re impérativement les préconisations
suivantes avant toute utilisation de vo-
tre appareil.
Avertissement Pour éviter tout risque
de détérioration de l'appareil,
transportez-le dans sa position
d'utilisation muni de ses cales de
transport (selon modèle). Au déballage
de celui-ci, et pour empêcher des
risques d'asphyxie et corporel, tenez
les matériaux d'emballage hors de la
portée des enfants.
Avertissement Pour éviter tout risque
(mobilier, immobilier, corporel,...),
l'installation, les raccordements (eau,
gaz, électricité, évacuation selon
modèle), la mise en service et la
maintenance de votre appareil doivent
être effectués par un professionnel
qualifié.
Avertissement Votre appareil a été
conçu pour être utilisé par des adultes.
Il est destiné à un usage domestique
normal. Ne l'utilisez pas à des fins
commerciales ou industrielles ou pour
d'autres buts que ceux pour lesquels il
a été conçu. Vous éviterez ainsi des
risques matériel et corporel.
Avertissement Débranchez votre
appareil avant toute opération de
nettoyage manuel. N'utilisez que des
produits du commerce non corrosifs
ou non inflammables. Toute projection
d'eau ou de vapeur est proscrite pour
écarter le risque d'électrocution.
Avertissement Si votre appareil est
équipé d'un éclairage, débranchez
l'appareil avant de procéder au
changement de l'ampoule (ou du néon,
etc.) pour éviter de s'électrocuter.
Avertissement Afin d'empêcher des
risques d'explosion et d'incendie, ne
placez pas de produits inflammables
ou d'éléments imbibés de produits
inflammables à l'intérieur, à proximité
ou sur l'appareil.
Avertissement Lors de la mise au
rebut de votre appareil, et pour écarter
tout risque corporel, mettez hors
d'usage ce qui pourrait présenter un
danger: coupez le câble d'alimentation
au ras de l'appareil. Informez-vous
auprès des services de votre commune
des endroits autorisés pour la mise au
rebut de l'appareil.
electrolux 19
Veuillez maintenant lire attentivement
cette notice pour une utilisation opti-
male de votre appareil.
CONSIGNES DE SÉCURITÉ
Pour votre sécurité et le bon fonction-
nement de l'appareil, lisez attentive-
ment ce manuel avant l'installation et
l'utilisation. Conservez ces instructions
à proximité de l'appareil. Les utilisa-
teurs doivent connaître parfaitement le
fonctionnement et les fonctions de sé-
curité de l'appareil.
Utilisation réglementaire
• Cet appareil est exclusivement destiné à
un usage domestique.
• Ce lave-vaisselle est conçu pour laver la
vaisselle et les ustensiles de cuisine pou-
vant être lavés en machine.
• N'utilisez pas de solvants dans votre ap-
pareil. Ceux-ci pourraient provoquer une
explosion !
• Les couteaux et autres ustensiles pointus
ou tranchants doivent être placés dans le
panier à couverts avec la pointe vers le
bas. ou posez-les en position horizontale
dans le panier supérieur.
• N'utilisez que des produits (sel, produit
de lavage, liquide de rinçage) spécifiques
pour lave-vaisselle.
• Evitez d'ouvrir la porte pendant que l'ap-
pareil fonctionne : une vapeur brûlante
peut s'en échapper. Risque de brûlures !
• Ne sortez pas la vaisselle du lave-vaissel-
le avant la fin du cycle de lavage.
• Lorsque le programme est terminé, dé-
branchez l'appareil et fermez le robinet
d'arrivée d'eau.
• Cet appareil ne peut être entretenu et ré-
paré que par un technicien autorisé, ex-
clusivement avec des pièces d'origine.
• N'essayez en aucun cas de réparer le la-
ve-vaisselle vous-même. Les réparations
effectuées par du personnel non qualifié
peuvent provoquer des blessures ou le
mauvais fonctionnement du lave-vaissel-
le. Contactez votre service après vente.
Exigez des pièces d'origine.
Sécurité générale
• Les personnes (y compris les enfants) qui
souffrent de capacités mentales, physi-
ques et sensorielles réduites ou qui ne se
sont pas familiarisées avec le mode de
fonctionnement de l'appareil, ne doivent
pas l'utiliser. Elles doivent être surveillées
ou dirigées par une personne responsa-
ble de leur sécurité.
• Respectez les consignes de sécurité du
fabricant du détergent pour éviter les brû-
lures aux yeux, à la bouche et la gorge.
• Ne buvez pas l'eau du lave-vaisselle. Des
résidus de produit de lavage peuvent res-
ter dans l'appareil.
• Fermez toujours la porte de l'appareil
lorsqu'il n'est pas utilisé pour empêcher
tout risque de blessure ou de chute acci-
dentelle.
• Ne vous asseyez pas ou ne montez pas
sur la porte ouverte.
Sécurité enfants
• Seuls les adultes doivent utiliser cet ap-
pareil. Veillez à ce que les enfants ne
jouent pas avec l'appareil.
• Rangez les emballages hors de la portée
des enfants. Ils présentent un risque de
suffocation.
• Rangez les détergents dans un endroit
sûr. Veillez à ce que les enfants ne tou-
chent pas les produits de lavage.
• Ne laissez pas les enfants s'approcher
de l'appareil quand la porte est ouverte.
20 electrolux
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Electrolux ESI64060X Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Electrolux ESI64060X User manual