Sub-Zero IR304PE/S/PH Mode d'emploi

INDUCTION RANGE

USE AND CARE GUIDE

CLEANING, MAINTENANCE, AND MORE

2

|

Wolf Customer Care 800.222.7820

Contents

4 Safety Precautions

8 Induction Range Features

9 Oven Operation

16 Surface Operation

20 Care Recommendations

21 Troubleshooting

23 Wolf Warranty

INDUCTION RANGE

wolfappliance.com

|

3

Customer Care

The model and serial number are printed on the enclosed

product registration card. Both numbers are also listed on

the product rating plate. Refer to page 8 for rating plate

location. For warranty purposes, you will also need the date

of installation and name of your authorized Wolf dealer.

Record this information below for future reference.

SERVICE INFORMATION

Model Number

Serial Number

Date of Installation

Certied Service Name

Certied Service Number

Authorized Dealer

Dealer Number

If your product ever needs attention, be sure to use a Wolf

Factory Certied Service provider recommended by our

customer care center, or select one from our list of providers

available at wolfappliance.com/locator. All Factory Certi-

ed Service providers are carefully selected and thoroughly

trained by us.

INDUCTION RANGE

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

4

|

Wolf Customer Care 800.222.7820

IMPORTANT INSTRUCTIONS

WARNING

A child or adult can tip this appliance and be

killed.

Verify the anti-tip device has been properly

installed and engaged. Ensure the anti-tip device

is re-engaged when this appliance is moved. Refer

to the illustrations below for how to verify correct

installation.

Do not operate this appliance without the anti-tip

device in place and engaged. Failure to do so

can result in death or serious burns to children or

adults.

To reduce the risk of burns, do not move this

appliance while hot.

SAFETY PRECAUTIONS

ANTI-TIP

DEVICE

ANTI-TIP

DEVICE

ENGAGED

Anti-tip device location.

Anti-tip device engaged.

GENERAL SAFETY PRECAUTIONS

• Read this guide carefully before using this appli-

ance to reduce risk of re, electric shock, or injury.

• Ensure proper installation and servicing. This appli-

ance must be properly installed and grounded by

a qualied technician. Have the installer show you

the location of the circuit breaker or fuse so that

you know where to turn off power.

• Warranty service must be performed by Wolf

Factory Certied Service.

•

Do not repair or replace any part of the appliance

unless it is specically recommended in literature

you received. All service should be referred to Wolf

Factory Certied Service.

• IMPORTANT NOTE: Performance may be compro-

mised if the electrical supply is less than 240 volts.

wolfappliance.com

|

5

SAFETY PRECAUTIONS

IMPORTANT INSTRUCTIONS

GENERAL SAFETY PRECAUTIONS

• Keep appliance area clear and free from combus-

tible material.

• Exercise caution when opening the oven door. Let

hot air or steam escape before looking or reaching

into the oven.

• Do not use aluminum foil to line any part of this

appliance.

• Be sure the oven cool air intake (above the door)

and oven exhaust vent (below the door) are unob-

structed at all times.

• Do not obstruct the ow of air to ensure proper

ventilation.

• Wear proper apparel. Loose-tting or hanging gar-

ments should never be worn using this appliance.

• Use extreme caution when moving a grease kettle

or disposing of hot grease.

• Use only dry pot holders when removing pans from

this appliance. Wet or damp pot holders can cause

steam burns. Do not use a towel or bulky cloth in

place of pot holders.

• Position oven racks in desired locations when oven

is cool. If a rack must be repositioned after the

oven is already hot, be sure pot holder does not

contact a hot heating element in the oven.

• Clean only those parts listed in this guide.

• Do not use oven cleaners. No commercial oven

cleaner or oven liner protective coating of any kind

should be used in or around any part of the oven.

• Before using self-clean, remove broiler pan, oven

racks, oven rack guides, and any other utensils.

• Do not clean the oven gasket; rubbing or moving

the gasket may compromise the door seal.

• Do not touch heating elements or interior surfaces

of the oven. Heating elements may be hot even

though they are dark in color. Interior surfaces

become hot enough to cause burns. During and

after use, do not touch or let clothing or other am-

mable materials contact heating elements or inte-

rior surfaces of oven until they have had sufcient

time to cool.

• Do not leave children alone or unattended in the

area where this appliance is in use. Never allow

children to sit or stand on the appliance.

• Do not store items of interest to children above or

at the back of this appliance, as they could climb

on the appliance to reach items and be injured.

• Do not heat unopened food containers, such as

baby food jars and cans. Pressure build-up may

cause the container to burst and cause injury.

• Do not store ammable materials in an oven near

burners or let grease or other ammable sub-

stances accumulate on this appliance.

6

|

Wolf Customer Care 800.222.7820

IMPORTANT INSTRUCTIONS

• Do not use water on grease res. Smother the ame

or use a dry chemical or foam-type extinguisher.

• Never leave this appliance unattended when in use.

Boilovers and greasy spills may smoke or ignite.

• Select cookware of the proper size, material, and

construction for the particular type of cooking

being done. This unit is equipped with induction

elements of different sizes. Refer to element rating

on page 8.

•

Never heat an empty pan. It may damage the

cooking surface or cookware and overheat the unit.

•

Do not heat cookware with water droplets on the

outside of the pan. The droplets may begin to boil

and splatter. Cookware should always be dry.

• When using the cooking surface, do not touch

the glass surface directly above or adjacent to the

induction elements or zones. The glass surface

may become hot enough to cause burns.

• Always turn pan handles inward so they do not

extend over adjacent work areas, induction ele-

ments, or edges of the cooking surface to reduce

the risk of burns, ignition of ammable materials,

and spillage due to unintentional contact with pan.

Do not turn handles toward the room, where they

may be bumped or easily hit.

SAFETY PRECAUTIONS

• Do not operate the induction elements if the glass-

ceramic surface is broken or severely pitted. Call

Wolf Factory Certied Service to repair the range.

• Do not store ammable materials near hot compo-

nents or let grease or other ammable substances

accumulate on the cooking surface.

• Do not clean the induction surface while it is still

hot. If using a damp sponge or cloth, wait until the

surface has cooled sufciently to prevent steam

burns. Also, some cleaners give off noxious fumes

when applied to hot surfaces. Refer to care recom-

mendations on page 20.

• Do not use a griddle, open roaster, or sh poacher

across two induction elements unless the bridge

element is turned on. This type of use without

the bridge element turned on could damage or

crack the glass. Refer to bridge element on

page 18.

• Do not block the cooling fan exhaust or intake

vents. The cooling fan automatically turns on to

cool internal parts. It may continue to run even

after the cooking surface has been turned off.

wolfappliance.com

|

7

IMPORTANT INSTRUCTIONS

WARNING

PROPOSITION 65 FOR CALIFORNIA RESIDENTS

Cancer and Reproductive Harm—

www.P65Warnings.ca.gov

SAFETY PRECAUTIONS

COMMONWEALTH OF MASSACHUSETTS

• Installations and repairs must be performed by a

qualied or licensed contractor, plumber, or gas

tter, qualied or licensed by the state, province, or

region where this appliance is being installed.

8

|

Wolf Customer Care 800.222.7820

INDUCTION RANGE FEATURES

Induction Range Features

FEATURES

1

Product Rating Plate

2

Oven Control Panel (press to access)

3

Oven Cooking Mode Selector Knob

4

Oven Temperature Control Knob

5

Convection Oven

6

Surface Control Panel

7

Induction Element

8

Bridge Element

Getting Started

We know you are eager to start cooking, but before you

do, please take some time to read this use and care guide.

Whether you are an occasional cook or an expert chef, it

will be to your benet to familiarize yourself with the safety

practices, features, operation, and care recommendations of

your Wolf induction range.

In induction cooking, the electricity ows through a coil to

produce a magnetic eld under the glass-ceramic surface.

When an induction-compatible pan is placed on the cooking

surface, currents are induced in the pan and instant heat is

generated. Cookware made of magnetic materials, such as

cast iron or magnetic stainless steel, is required for induc-

tion cooking.

To ensure all residual oil from the manufacturing process

has been removed, clean the range thoroughly with hot

water and mild detergent prior to use. Rinse and dry with a

soft cloth. Refer to care recommendations on page 20.

To ensure the best results, review cooking modes and

special features on page 12.

CAUTION

Do not place cookware on the oven oor or use

aluminum foil or other material to line the oven oor or

side walls. Failure to adhere to this notice will damage

the porcelain interior and will void your warranty.

INDUCTION ELEMENT RATING

30" RANGE W

11" (279) 2600 | 3150 boost

8"

(203) 2100 | 3000 boost

8" (203) 2100

6"

(152) 1400

36" RANGE W

11" (279) 2600 | 3700 boost

(2) 8"

(203) 2100 | 3000 boost

(2) 8"

(203) 2100

36" induction range shown.

4

5

1

2

8

7

3

6

wolfappliance.com

|

9

The bottom oven rack has full-extension capability that is

supported by the oven door. With the rack in the lowest

rack guide position, slide it onto the door guides for greater

stability and accessibility. Refer to the illustration below.

To insert a full-extension easy glide rack, place the two rear

tabs onto the rack guide (one tab above and one below).

Refer to the illustration below. Angle the rack slightly and

slide back until the front rack notch engages the front rack

guide.

Oven Racks

OVEN RACK GUIDES

To insert the rack guides in the oven, locate the mounting

screws on the oven side walls. Place the rack guide

mounting tabs over the screws and slide down until fully

seated. Refer to the illustration below.

OVEN RACKS

To insert a standard rack in the oven, place the rack anti-tip

lock under the side rack guide rails. Slide the rack back

and lift up to clear the rack stops. Continue to slide the

rack back until it is completely inside the oven. Refer to the

illustration below.

OVEN OPERATION

MOUNTING

TAB

MOUNTING

SCREW

ANTI-TIP

LOCK

RACK STOP

Oven rack guides.

Oven rack anti-tip lock.

REAR TABS

NOTCH

Bottom rack.

Full-extension rack.

10

|

Wolf Customer Care 800.222.7820

OVEN LIGHT

The oven light turns on automatically when the door is open

and off when closed. To turn the light on while the door is

closed, touch OVEN LIGHT on the control panel.

PREHEAT

During preheat, the oven is heated as quickly and evenly

as possible and is not ideal for cooking. Preheat should

be used for all cooking modes except broil and convec-

tion broil. During preheat, temperatures below 150°F

(65°C)

appear as ‘Lo’. Once preheat is complete, an audible chime

indicates the oven has reached the set temperature and

the oven indicator light is no longer illuminated. To adjust

temperature once preheat is complete, turn the knob to the

desired temperature.

PRIOR TO USE

To ensure all residual oil from the manufacturing process

has been removed:

1 Clean oven thoroughly with hot water and mild deter-

gent. Rinse and dry with a soft cloth.

2 Turn on ventilation. Some smoke and odor is normal.

3 Rotate the mode selector knob to ROAST and set the

temperature to 550°F

(290°C) for one hour.

4 Rotate mode selector knob to OFF and allow oven to

cool with the door closed.

OVEN OPERATION

Oven Operation

Wolf induction ranges use a combination of a cooking mode

selector knob, oven temperature control knob, and elec-

tronic control panel to select desired cooking modes, oven

temperature, and exclusive features. Open the control panel

by pressing

.

Temperatures are displayed in Fahrenheit. To change to

Celsius, touch and hold CLOCK for 5 seconds. Touch

COOK TIME to alternate between °F and °C, then touch

ENTER.

When using the oven, Wolf has created a two-step process

to ensure it is never accidentally turned on:

1 Rotate the cooking mode selector knob to the desired

cooking mode. Convection modes are indicated by

.

Refer to the illustration below. Once the desired cooking

mode is selected, a preset temperature will appear on

the temperature control knob.

2 Select the preset temperature by touching ENTER on

the control panel, or turn the temperature control knob

to increase or decrease temperature. Either action

completes the second step of the process. The oven

indicator light illuminates and preheat begins.

TIMER

TEMPERATURE

CONTROL KNOB

COOKING MODE

SELECTOR KNOB

Oven controls.

wolfappliance.com

|

11

OVEN OPERATION

Oven Operation

CLOCK

The clock is visible on the control panel during all cooking

modes, except when the timer is in use. It is very important

the clock is set to the correct time if the cook time or stop

time feature is used. The clock must be reset after a power

outage.

Setting clock:

1 Touch CLOCK on the control panel.

2 Use up and down arrows to set the time of day. Time will

change from a.m. to p.m. by passing 12:00.

3 Touch CLOCK. An audible chime indicates the time has

been set.

4 To change to a 24-hour clock, press and hold CLOCK for

5 seconds. Touch CLOCK, then ENTER.

CLOCK STANDBY POWER

The range is shipped in standby power mode, which dis-

ables the clock approximately 10 minutes after the cooling

fan operation is complete or the oven is inactive. The clock

will illuminate after any touch of the controls or oven use.

Enable | disable standby power:

1 Touch and hold CLOCK on the control panel for 5

seconds.

2 Touch STOP TIME to toggle on or off, then touch

ENTER.

TIMER

The timer on the oven control panel can be set for a

maximum of 9 hours and 59 minutes. Once a time is set, the

countdown is illuminated on the control panel display. The

last minute counts down in seconds. The timer is indepen-

dent from the oven. Setting the timer does not affect cook

time or stop time. For information regarding auto program

features, refer to page 14.

Setting timer:

1 Touch TIMER on the oven control panel.

2 Use up and down arrows to set the time in hours and

minutes.

3 Touch TIMER to start. An audible chime indicates timer

has been set. Oven will chime and time will ash when

complete. Timer will continue to chime until CLEAR is

touched on the control panel.

12

|

Wolf Customer Care 800.222.7820

OVEN OPERATION

Cooking Modes

MODE MODE KNOB PRESET RANGE PROBE USES

Convection

CONV

325°F

(165°C)

170 – 550°F

(75 – 290°C)

•

Uniform air movement makes it possible to use multiple

racks to cook with even browning.

Convection Bake

BAKE

375°F

(190°C)

170 – 550°F

(75 – 290°C)

•

Ideal for pie baking.

Convection Broil

BROIL

Br1

Br2

Br3

550°F (290°C)

450°F (230°C)

350°F (175°C)

Shortens broiling times for thicker cuts of meat, sh, and

poultry. Use a two-piece broiler pan, and always broil with

oven door closed.

Convection Roast

ROAST

325°F

(165°C)

170 – 550°F

(75 – 290°C)

•

Perfect for roasting tender cuts of beef, lamb, pork, and

poultry.

Bake BAKE 350°F

(175°C)

170 – 550°F

(75 – 290°C)

•

Best for single-rack cooking, primarily baked foods. Use

for standard recipes.

Broil BROIL Br1

Br2

Br3

550°F (290°C)

450°F (230°C)

350°F (175°C)

Best for broiling meats, sh, and poultry pieces up to 1"

thick. Use a two-piece broiler pan, and always broil with

oven door closed.

Roast ROAST 350°F

(175°C)

170 – 550°F

(75 – 290°C)

•

Best for roasting less tender cuts of meat, such as chuck

roasts and stew meat.

Bake Stone STONE 400°F

(205°C)

170 – 550°F

(75 – 290°C)

•

Baking on a ceramic stone. Great for pizza and bread.

Bake stone accessory required.

Dehydration

CONV

135°F

(60°C)

110 – 160°F

(45 – 70°C)

Dry a variety of fruits, vegetables, and meats. Accessory

racks required. Refer to page 13.

Self-Clean CLEAN

Oven heats to an extremely high temperature to allow food

soil to burn off. Refer to page 14.

O

F

B

A

K

E

B

R

O

I

L

R

O

A

S

T

S

T

O

N

E

C

L

E

A

N

C

O

N

V

R

O

A

S

T

B

R

O

I

L

B

A

K

E

Cooking mode selector knob.

wolfappliance.com

|

13

Temperature Probe

The temperature probe measures the internal temperature

of food while cooking. It can be used with all cooking

modes except broil and convection broil.

Setting controls:

1 Rotate the mode selector knob to the desired cooking

mode.

2 Touch ENTER to select the preset temperature, or turn

the temperature control knob to change the temperature.

3 Insert the probe into the thickest area of food. When

making bread, cook for approximately 10 minutes before

inserting probe.

4 When preheat is complete, use a pot holder to lift the

probe receptacle cover, then insert the probe. Refer to

the illustration below.

5 The probe temperature is preset to 160°F (70°C). Touch

ENTER to select the preset temperature, or turn the

temperature control knob to change the temperature.

The display alternates between the oven set temperature

and the actual probe temperature. To alternate between

probe set point and actual probe temperature, press

PROBE. Temperatures below 70°F

(20°C) are displayed

as ‘Lo.’

6 An audible chime indicates the internal temperature has

reached the probe set point. Remove, then reinsert the

probe to verify internal temperature.

CAUTION

Probe and probe receptacle will be very hot. Handle

with care.

OVEN OPERATION

Proof

Setting controls:

1 Rotate the mode selector knob to BAKE.

2 Turn the temperature control knob left until ‘PrF’

appears, then release.

3 The oven temperature is preset to 85°F (30°C). Touch

ENTER to select the preset temperature, or turn the tem-

perature control knob to change the temperature. The

display alternates between the set temperature and ‘PrF.’

Dehydration

Accessory kit required. Accessories are avail able through an

authorized Wolf dealer. For local dealer information, visit the

nd a showroom section of our website, wolfappliance.com.

Setting controls:

1 Place the door stop supplied with accessory kit onto the

oven door lock.

2 Rotate the mode selector knob to CONV.

3 Turn the temperature control knob left until ‘dEH’

appears, then release.

4 The oven temperature is preset to 110°F (45°C). Touch

ENTER to select the preset temperature, or turn the

temperature control knob to change the temperature.

The display alternates between the set temperature and

‘dEH.’

Probe receptacle.

14

|

Wolf Customer Care 800.222.7820

OVEN OPERATION

Self-Clean

During self-clean, the oven is heated to an extremely high

temperature to burn off food soil. Remove all oven racks

and rack guides. They will discolor if left in during self-clean.

The oven door will lock and remain locked until self-clean is

complete and the oven temperature has cooled below 300°F

(150°C)

. Self-clean times include one hour for cool-down.

Setting controls for 4-hour self-clean:

1 Rotate the mode selector knob to CLEAN.

2 Touch ENTER.

Setting controls for 3-hour self-clean:

1 Rotate the mode selector knob to CLEAN.

2 Touch STOP TIME.

3 Touch the down arrow to reduce stop time by 1 hour.

4 Touch ENTER twice.

CAUTION

During self-clean, exterior surfaces may get hotter than

usual. Children should be kept away.

Auto Program

TIMED COOK

Timed cook automatically turns the oven off at a specied

time. The oven will begin to heat immediately and will turn

off at the desired stop time. The clock must be set to the

correct time for timed cook to function properly. Use in

any cooking mode except broil, convection broil, and bake

stone.

Setting controls:

1 Rotate the mode selector knob to the desired cooking

mode.

2 Touch ENTER to select the preset temperature, or turn

the temperature control knob to change the temperature.

3 Touch COOK TIME. Use the arrows to select desired

cook time in hours and minutes.

4 Touch ENTER.

DELAYED START

Delayed start automatically turns the oven on and off at

specied times. The oven will remain idle until the desired

start time and will turn off at the desired stop time. The

clock must be set to the correct time for delayed start to

function properly. Use in any cooking mode except broil,

convection broil, and bake stone.

Setting controls:

1 Rotate the mode selector knob to the desired cooking

mode.

2 Touch ENTER to select the preset temperature, or turn

the temperature control knob to change the temperature.

If ENTER is touched, the oven will begin to heat immedi-

ately but will enter idle mode once the stop time is set.

3 Touch COOK TIME. Use the arrows to select desired

cook time in hours and minutes.

4 Touch STOP TIME. Use the arrows to select desired time

oven should turn off.

5 Touch ENTER.

wolfappliance.com

|

15

OVEN OPERATION

Sabbath (oven only)

This appliance is certied by Star-K to meet strict religious

regulations in conjunction with specic instructions found

on www.star-k.org.

Sabbath overrides the automatic 12-hour shut off feature.

Sabbath must be reset after a power outage.

Setting controls:

1 Turn the oven light on or off.

2 Rotate the mode selector knob to BAKE or ROAST and

select desired temperature.

3 Touch and hold ENTER for 5 seconds. ‘SAb’ will appear

and ash on the oven control knob indicating Sabbath

mode has been initiated.

4 To change the oven temperature while in Sabbath

mode, turn the temperature control knob. Each turn will

increase or decrease the temperature by 10° (F or C).

The display and audible chime are disabled, but tem-

perature will randomly change after the new temperature

is selected. The oven will remain on until mode selector

knob is rotated to OFF.

Oven Light

WARNING

Verify power is disconnected from the electrical box

before replacing a light bulb.

Allow the oven to cool completely, then remove oven racks

and rack guides. To remove the light cover, gently pry the

bottom edge with a flat screwdriver. Remove the existing

bulb and replace with a 40-watt halogen bulb. Refer to the

illustration below.

LIGHT

COVER

Light bulb replacement.

16

|

Wolf Customer Care 800.222.7820

SURFACE OPERATION

Surface Operation

CONTROL PANEL

The control panel features illuminated touch controls that

are invisible when the cooking surface is off. A power level

indicator for each control displays the heat setting from SIM

(MLT) to HI. Each control is positioned to the corresponding

induction element. Refer to the illustration below.

Indicators on the control panel will illuminate to indicate

specic surface operation. Refer to the chart below.

INDICATORS

Control Panel Lock

Element(s) On

Hot Surface

Timer Set

Boost Mode

Front-to-Back Bridge

Side-to-Side Bridge (36" model only)

All Bridge (36" model only)

CAUTION

Do not place hot cookware directly over the control

panel.

CONTROL PANEL LOCK

The control panel lock feature prevents unwanted surface

operation. Touch and hold LOCK for three seconds to lock

and unlock the control panel.

will illuminate when the

control panel is locked.

The control panel will automatically lock after 10 minutes

of inactivity. This automatic lock feature can be disabled

through the extended options menu. Refer to page 19.

When the range is powered up for the rst time and after

a power outage, the induction surface will default to lock

mode.

Touch controls.

ELEMENT

CONTROL

wolfappliance.com

|

17

SURFACE OPERATION

Surface Operation

POWER LEVEL INDICATOR

When an element is activated, a power level indicator will

illuminate above the corresponding control indicating the

level of heat. The lowest heat is represented by the small

ame, varying levels of heat by additional indicators (dots),

and the highest heat by all indicators including the large

ame. Refer to the chart and illustration below.

SETTING POWER LEVEL USES

Melt 1 (small ame)

indicator

Melting butter and holding

chocolate and sauces.

Simmer 2–6 indicators Simmering sauces and

steaming rice.

Medium 6–7 indicators Making French toast and pan-

cakes and heating milk, cream

sauces, soups, and gravies.

Medium High 7-8 indicators Sauteing, browning, and frying.

High 8–10 (large ame)

indicators

Boiling water, searing meat,

and canning.

Power level indicator.

SINGLE ELEMENT | INNER ZONE

Setting controls:

1 To activate an induction element, touch ON/OFF for the

desired single element on the control panel. The power

level indicator will ash, and all indicators for that zone

will ash. Refer to the illustration below.

2 To complete the activation, touch HI for highest heat,

SIM (MLT) for lowest heat, BOOST to activate boost

mode, or the desired power level indicator.

3 To change heat setting while the element is on, touch or

slide to the desired power level.

4 To turn element off, touch ON/OFF.

IMPORTANT NOTE: If no cookware or incompatible cook-

ware is placed on an induction element after activation, the

control will ash for 30 seconds, then the element will turn

off automatically.

Element activation.

ON/OFF

18

|

Wolf Customer Care 800.222.7820

SURFACE OPERATION

Surface Operation

BOOST MODE

Boost mode boosts power on one element by diverting

power from an adjacent element. If the adjacent element is

on high, the power output will be reduced. The reduction in

power will be displayed on the power level indicator of the

adjacent element. Refer to the illustration below.

will

illuminate when an element is in boost mode.

Boost mode will deactivate automatically after approxi-

mately 15 minutes of continuous operation and can be

reactivated if desired.

BRIDGE ELEMENT

Setting controls:

1 To activate a bridge, select the desired power level on

one of the single elements.

2 Touch BRIDGE between corresponding element con-

trols to bridge elements front to back, BRG to bridge

elements side to side, or ALL BRIDGE to bridge all

elements.

, or will illuminate respectively.

3 To change the power level, adjust the power level on any

active bridged element.

4 To turn off, touch ON/OFF on any active bridged

element.

ALL BRIDGE should be used for cookware larger than

12"

(305) in diameter. For smaller cookware, use the right

rear element.

GRIDDLE USE

The bridge element provides an oblong heating area for use

with a griddle, open roaster, or sh poacher.

To preheat a griddle, set the bridge element power level to

high for ve minutes, then reduce for cooking.

CAUTION

A griddle, open roaster, or sh poacher should not be

used when the bridge element is off or with any other

combination of heating elements.

Boost mode.

BOOST

wolfappliance.com

|

19

SURFACE OPERATION

Surface Operation

TIMER

The surface timer can be set in one-minute increments up

to 99 minutes. Once a time is set,

will illuminate on the

surface control panel, and the countdown is visible on the

timer display. The timer is independent from the cooking

surface. Refer to the illustration below.

Setting timer:

1 Touch TIMER.

2 Touch and hold + or – until desired time is shown in the

timer display. Timer will begin the countdown in minutes.

3 Timer will chime with one minute left and will complete

the countdown in seconds.

4 When complete, the timer will chime and continue to

chime until TIMER is touched.

HOT SURFACE INDICATOR

will illuminate on the surface control panel and may

remain illuminated even when the induction surface is off.

ALL OFF

When one or more induction elements are on, will illu-

minate on the surface control panel. To turn off all elements

at the same time, touch ALL OFF. Refer to the illustration

below.

EXTENDED OPTIONS

The extended options feature allows the user to set pref-

erences for volume, tone, and surface control panel lock

feature.

Setting adjustment:

1 While the unit is off and unlocked, touch and hold ALL

OFF for ve seconds.

2 Power level 1 on the rear element control will be dis-

played and ‘VO’ will appear on the timer display.

Touch SIM (MLT) or HI on the front element control to

adjust volume.

3 Touch + on the timer control to adjust tone. Power level

2 on the rear element control will be displayed, and ‘Fr’

will appear on the timer display.

Touch SIM (MLT) or HI on the front element control to

adjust tone.

4 Touch + on the timer control to adjust the automatic

control panel lock. Power level 3 on the rear element

control will be displayed, and ‘Lo’ will appear on the

timer display.

Touch SIM (MLT) or HI on the front element control to

turn the automatic lock feature off or on respectively.

5 Touch ALL OFF at any time while in extended options to

conrm settings and return to idle.

Timer controls.

All off.

TIMER

ALL OFF

20

|

Wolf Customer Care 800.222.7820

CARE RECOMMENDATIONS

Care Recommendations

CLEANING

Stainless steel Use a nonabrasive stainless steel cleaner and apply with a soft lint-free cloth. To bring out the natural luster,

lightly wipe surface with a water-dampened microber cloth followed by a dry polishing chamois. Always

follow the grain of the stainless steel.

Glass-ceramic surface Allow to cool. Use a spray degreaser to remove ngerprints and a non-abrasive Ceran® cooktop cleaner for

food soil. Do not allow any item that could melt to come in contact with the glass-ceramic surface when hot.

If this occurs, use the razor blade scraper provided with the range to remove.

Control panel Use a spray degreaser to remove ngerprints and food soil. Spray on a cloth before wiping the panel.

IMPORTANT NOTE: Do not spray cleaners directly on the control panel.

Control knobs Using a damp cloth, wipe with a mild detergent or spray degreaser. Rinse and dry. Do not place in the

dishwasher.

Oven rack guides Remove and place on a at surface near the sink. Clean with hot water and mild detergent or paste of

baking soda and water. Do not immerse in water. Towel dry.

Oven interior Before using the self-clean feature, use a razor blade to gently lift baked-on foods from the oven cavity

and window. For stubborn stains, spray with a mild abrasive cleaner, or spray degreaser and scrub with a

no-scratch Scotch-Brite™ pad (pink or blue). Wash the entire oven cavity with soap and water to remove

cleaning chemicals before entering self-clean mode. If residue is not cleaned from the cavity, etching of the

porcelain may occur. Once the self-clean cycle is complete, allow the oven to cool completely and wipe out

ash with a damp cloth.

Broiler pan To clean the upper rack, use a mild detergent and scouring pad. Rinse and dry. To clean the bottom pan,

discard grease and wash with hot water and mild detergent. Rinse and dry. The stainless steel upper rack is

dishwasher safe. However, do not place any porcelain-coated rack or pan in the dishwasher.

La page charge ...

Sub-Zero IR304PE/S/PH Mode d'emploi

Ce manuel convient également à

Sub-Zero IR304PE/S/PH Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents