Sub-Zero IR304TE/S/TH Mode d'emploi

Catégorie
Micro-ondes
Taper
Mode d'emploi

Ce manuel convient également à

INDUCTION RANGE
USE AND CARE GUIDE
CLEANING, MAINTENANCE, AND MORE
2
|
Wolf Customer Care 800.222.7820
Contents
4 Safety Precautions
8 Induction Range Features
9 Oven Operation
16 Surface Operation
20 Care Recommendations
21 Troubleshooting
23 Wolf Warranty
INDUCTION RANGE
wolfappliance.com
|
3
Customer Care
The model and serial number are printed on the enclosed
product registration card. Both numbers are also listed on
the product rating plate. Refer to page 8 for rating plate
location. For warranty purposes, you will also need the date
of installation and name of your authorized Wolf dealer.
Record this information below for future reference.
SERVICE INFORMATION
Model Number
Serial Number
Date of Installation
Certied Service Name
Certied Service Number
Authorized Dealer
Dealer Number
If your product ever needs attention, be sure to use a Wolf
Factory Certied Service provider recommended by our
customer care center, or select one from our list of providers
available at wolfappliance.com/locator. All Factory Certi-
ed Service providers are carefully selected and thoroughly
trained by us.
INDUCTION RANGE
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
4
|
Wolf Customer Care 800.222.7820
IMPORTANT INSTRUCTIONS
WARNING
A child or adult can tip this appliance and be
killed.
Verify the anti-tip device has been properly
installed and engaged. Ensure the anti-tip device
is re-engaged when this appliance is moved. Refer
to the illustrations below for how to verify correct
installation.
Do not operate this appliance without the anti-tip
device in place and engaged. Failure to do so
can result in death or serious burns to children or
adults.
To reduce the risk of burns, do not move this
appliance while hot.
SAFETY PRECAUTIONS
ANTI-TIP
DEVICE
ANTI-TIP
DEVICE
ENGAGED
Anti-tip device location.
Anti-tip device engaged.
GENERAL SAFETY PRECAUTIONS
Read this guide carefully before using this appli-
ance to reduce risk of re, electric shock, or injury.
Ensure proper installation and servicing. This appli-
ance must be properly installed and grounded by
a qualied technician. Have the installer show you
the location of the circuit breaker or fuse so that
you know where to turn off power.
Warranty service must be performed by Wolf
Factory Certied Service.
Do not repair or replace any part of the appliance
unless it is specically recommended in literature
you received. All service should be referred to Wolf
Factory Certied Service.
IMPORTANT NOTE: Performance may be compro-
mised if the electrical supply is less than 240 volts.
wolfappliance.com
|
5
SAFETY PRECAUTIONS
IMPORTANT INSTRUCTIONS
GENERAL SAFETY PRECAUTIONS
Keep appliance area clear and free from combus-
tible material.
Exercise caution when opening the oven door. Let
hot air or steam escape before looking or reaching
into the oven.
Do not use aluminum foil to line any part of this
appliance.
Be sure the oven cool air intake (above the door)
and oven exhaust vent (below the door) are unob-
structed at all times.
Do not obstruct the ow of air to ensure proper
ventilation.
Wear proper apparel. Loose-tting or hanging gar-
ments should never be worn using this appliance.
Use extreme caution when moving a grease kettle
or disposing of hot grease.
Use only dry pot holders when removing pans from
this appliance. Wet or damp pot holders can cause
steam burns. Do not use a towel or bulky cloth in
place of pot holders.
Position oven racks in desired locations when oven
is cool. If a rack must be repositioned after the
oven is already hot, be sure pot holder does not
contact a hot heating element in the oven.
Clean only those parts listed in this guide.
Do not use oven cleaners. No commercial oven
cleaner or oven liner protective coating of any kind
should be used in or around any part of the oven.
Before using self-clean, remove broiler pan, oven
racks, oven rack guides, and any other utensils.
Do not clean the oven gasket; rubbing or moving
the gasket may compromise the door seal.
Do not touch heating elements or interior surfaces
of the oven. Heating elements may be hot even
though they are dark in color. Interior surfaces
become hot enough to cause burns. During and
after use, do not touch or let clothing or other am-
mable materials contact heating elements or inte-
rior surfaces of oven until they have had sufcient
time to cool.
Do not leave children alone or unattended in the
area where this appliance is in use. Never allow
children to sit or stand on the appliance.
Do not store items of interest to children above or
at the back of this appliance, as they could climb
on the appliance to reach items and be injured.
Do not heat unopened food containers, such as
baby food jars and cans. Pressure build-up may
cause the container to burst and cause injury.
Do not store ammable materials in an oven near
burners or let grease or other ammable sub-
stances accumulate on this appliance.
6
|
Wolf Customer Care 800.222.7820
IMPORTANT INSTRUCTIONS
Do not use water on grease res. Smother the ame
or use a dry chemical or foam-type extinguisher.
Never leave this appliance unattended when in use.
Boilovers and greasy spills may smoke or ignite.
Select cookware of the proper size, material, and
construction for the particular type of cooking
being done. This unit is equipped with induction
elements of different sizes. Refer to element rating
on page 8.
Never heat an empty pan. It may damage the
cooking surface or cookware and overheat the unit.
Do not heat cookware with water droplets on the
outside of the pan. The droplets may begin to boil
and splatter. Cookware should always be dry.
When using the cooking surface, do not touch
the glass surface directly above or adjacent to the
induction elements or zones. The glass surface
may become hot enough to cause burns.
Always turn pan handles inward so they do not
extend over adjacent work areas, induction ele-
ments, or edges of the cooking surface to reduce
the risk of burns, ignition of ammable materials,
and spillage due to unintentional contact with pan.
Do not turn handles toward the room, where they
may be bumped or easily hit.
SAFETY PRECAUTIONS
Do not operate the induction elements if the glass-
ceramic surface is broken or severely pitted. Call
Wolf Factory Certied Service to repair the range.
Do not store ammable materials near hot compo-
nents or let grease or other ammable substances
accumulate on the cooking surface.
Do not clean the induction surface while it is still
hot. If using a damp sponge or cloth, wait until the
surface has cooled sufciently to prevent steam
burns. Also, some cleaners give off noxious fumes
when applied to hot surfaces. Refer to care recom-
mendations on page 20.
Do not use a griddle, open roaster, or sh poacher
across two induction elements unless the bridge
element is turned on. This type of use without
the bridge element turned on could damage or
crack the glass. Refer to bridge element on
page 18.
Do not block the cooling fan exhaust or intake
vents. The cooling fan automatically turns on to
cool internal parts. It may continue to run even
after the cooking surface has been turned off.
wolfappliance.com
|
7
IMPORTANT INSTRUCTIONS
WARNING
PROPOSITION 65 FOR CALIFORNIA RESIDENTS
Cancer and Reproductive Harm—
www.P65Warnings.ca.gov
SAFETY PRECAUTIONS
COMMONWEALTH OF MASSACHUSETTS
Installations and repairs must be performed by a
qualied or licensed contractor, plumber, or gas
tter, qualied or licensed by the state, province, or
region where this appliance is being installed.
8
|
Wolf Customer Care 800.222.7820
INDUCTION RANGE FEATURES
Induction Range Features
FEATURES
1
Product Rating Plate
2
Oven Control Panel (press to access)
3
Oven Cooking Mode Selector Knob
4
Oven Temperature Control Knob
5
Convection Oven
6
Surface Control Panel
7
Induction Element
8
Bridge Element
Getting Started
We know you are eager to start cooking, but before you
do, please take some time to read this use and care guide.
Whether you are an occasional cook or an expert chef, it
will be to your benet to familiarize yourself with the safety
practices, features, operation, and care recommendations of
your Wolf induction range.
In induction cooking, the electricity ows through a coil to
produce a magnetic eld under the glass-ceramic surface.
When an induction-compatible pan is placed on the cooking
surface, currents are induced in the pan and instant heat is
generated. Cookware made of magnetic materials, such as
cast iron or magnetic stainless steel, is required for induc-
tion cooking.
To ensure all residual oil from the manufacturing process
has been removed, clean the range thoroughly with hot
water and mild detergent prior to use. Rinse and dry with a
soft cloth. Refer to care recommendations on page 20.
To ensure the best results, review cooking modes and
special features on page 12.
CAUTION
Do not place cookware on the oven oor or use
aluminum foil or other material to line the oven oor or
side walls. Failure to adhere to this notice will damage
the porcelain interior and will void your warranty.
INDUCTION ELEMENT RATING
30" RANGE W
11" (279) 2600 | 3150 boost
8"
(203) 2100 | 3000 boost
8" (203) 2100
6"
(152) 1400
36" RANGE W
11" (279) 2600 | 3700 boost
(2) 8"
(203) 2100 | 3000 boost
(2) 8"
(203) 2100
36" induction range shown.
4
5
1
2
8
7
3
6
wolfappliance.com
|
9
The bottom oven rack has full-extension capability that is
supported by the oven door. With the rack in the lowest
rack guide position, slide it onto the door guides for greater
stability and accessibility. Refer to the illustration below.
To insert a full-extension easy glide rack, place the two rear
tabs onto the rack guide (one tab above and one below).
Refer to the illustration below. Angle the rack slightly and
slide back until the front rack notch engages the front rack
guide.
Oven Racks
OVEN RACK GUIDES
To insert the rack guides in the oven, locate the mounting
screws on the oven side walls. Place the rack guide
mounting tabs over the screws and slide down until fully
seated. Refer to the illustration below.
OVEN RACKS
To insert a standard rack in the oven, place the rack anti-tip
lock under the side rack guide rails. Slide the rack back
and lift up to clear the rack stops. Continue to slide the
rack back until it is completely inside the oven. Refer to the
illustration below.
OVEN OPERATION
MOUNTING
TAB
MOUNTING
SCREW
ANTI-TIP
LOCK
RACK STOP
Oven rack guides.
Oven rack anti-tip lock.
REAR TABS
NOTCH
Bottom rack.
Full-extension rack.
10
|
Wolf Customer Care 800.222.7820
OVEN LIGHT
The oven light turns on automatically when the door is open
and off when closed. To turn the light on while the door is
closed, touch OVEN LIGHT on the control panel.
PREHEAT
During preheat, the oven is heated as quickly and evenly
as possible and is not ideal for cooking. Preheat should
be used for all cooking modes except broil and convec-
tion broil. During preheat, temperatures below 150°F
(65°C)
appear as ‘Lo’. Once preheat is complete, an audible chime
indicates the oven has reached the set temperature and
the oven indicator light is no longer illuminated. To adjust
temperature once preheat is complete, turn the knob to the
desired temperature.
PRIOR TO USE
To ensure all residual oil from the manufacturing process
has been removed:
1 Clean oven thoroughly with hot water and mild deter-
gent. Rinse and dry with a soft cloth.
2 Turn on ventilation. Some smoke and odor is normal.
3 Rotate the mode selector knob to ROAST and set the
temperature to 550°F
(290°C) for one hour.
4 Rotate mode selector knob to OFF and allow oven to
cool with the door closed.
OVEN OPERATION
Oven Operation
Wolf induction ranges use a combination of a cooking mode
selector knob, oven temperature control knob, and elec-
tronic control panel to select desired cooking modes, oven
temperature, and exclusive features. Open the control panel
by pressing
.
Temperatures are displayed in Fahrenheit. To change to
Celsius, touch and hold CLOCK for 5 seconds. Touch
COOK TIME to alternate between °F and °C, then touch
ENTER.
When using the oven, Wolf has created a two-step process
to ensure it is never accidentally turned on:
1 Rotate the cooking mode selector knob to the desired
cooking mode. Convection modes are indicated by
.
Refer to the illustration below. Once the desired cooking
mode is selected, a preset temperature will appear on
the temperature control knob.
2 Select the preset temperature by touching ENTER on
the control panel, or turn the temperature control knob
to increase or decrease temperature. Either action
completes the second step of the process. The oven
indicator light illuminates and preheat begins.
TIMER
TEMPERATURE
CONTROL KNOB
COOKING MODE
SELECTOR KNOB
Oven controls.
wolfappliance.com
|
11
OVEN OPERATION
Oven Operation
CLOCK
The clock is visible on the control panel during all cooking
modes, except when the timer is in use. It is very important
the clock is set to the correct time if the cook time or stop
time feature is used. The clock must be reset after a power
outage.
Setting clock:
1 Touch CLOCK on the control panel.
2 Use up and down arrows to set the time of day. Time will
change from a.m. to p.m. by passing 12:00.
3 Touch CLOCK. An audible chime indicates the time has
been set.
4 To change to a 24-hour clock, press and hold CLOCK for
5 seconds. Touch CLOCK, then ENTER.
CLOCK STANDBY POWER
The range is shipped in standby power mode, which dis-
ables the clock approximately 10 minutes after the cooling
fan operation is complete or the oven is inactive. The clock
will illuminate after any touch of the controls or oven use.
Enable | disable standby power:
1 Touch and hold CLOCK on the control panel for 5
seconds.
2 Touch STOP TIME to toggle on or off, then touch
ENTER.
TIMER
The timer on the oven control panel can be set for a
maximum of 9 hours and 59 minutes. Once a time is set, the
countdown is illuminated on the control panel display. The
last minute counts down in seconds. The timer is indepen-
dent from the oven. Setting the timer does not affect cook
time or stop time. For information regarding auto program
features, refer to page 14.
Setting timer:
1 Touch TIMER on the oven control panel.
2 Use up and down arrows to set the time in hours and
minutes.
3 Touch TIMER to start. An audible chime indicates timer
has been set. Oven will chime and time will ash when
complete. Timer will continue to chime until CLEAR is
touched on the control panel.
12
|
Wolf Customer Care 800.222.7820
OVEN OPERATION
Cooking Modes
MODE MODE KNOB PRESET RANGE PROBE USES
Convection
CONV
325°F
(165°C)
170 – 550°F
(75 – 290°C)
Uniform air movement makes it possible to use multiple
racks to cook with even browning.
Convection Bake
BAKE
375°F
(190°C)
170 – 550°F
(75 – 290°C)
Ideal for pie baking.
Convection Broil
BROIL
Br1
Br2
Br3
550°F (290°C)
450°F (230°C)
350°F (175°C)
Shortens broiling times for thicker cuts of meat, sh, and
poultry. Use a two-piece broiler pan, and always broil with
oven door closed.
Convection Roast
ROAST
325°F
(165°C)
170 – 550°F
(75 – 290°C)
Perfect for roasting tender cuts of beef, lamb, pork, and
poultry.
Bake BAKE 350°F
(175°C)
170 – 550°F
(75 – 290°C)
Best for single-rack cooking, primarily baked foods. Use
for standard recipes.
Broil BROIL Br1
Br2
Br3
550°F (290°C)
450°F (230°C)
350°F (175°C)
Best for broiling meats, sh, and poultry pieces up to 1"
thick. Use a two-piece broiler pan, and always broil with
oven door closed.
Roast ROAST 350°F
(175°C)
170 – 550°F
(75 – 290°C)
Best for roasting less tender cuts of meat, such as chuck
roasts and stew meat.
Bake Stone STONE 400°F
(205°C)
170 – 550°F
(75 – 290°C)
Baking on a ceramic stone. Great for pizza and bread.
Bake stone accessory required.
Dehydration
CONV
135°F
(60°C)
110 – 160°F
(45 – 70°C)
Dry a variety of fruits, vegetables, and meats. Accessory
racks required. Refer to page 13.
Self-Clean CLEAN
Oven heats to an extremely high temperature to allow food
soil to burn off. Refer to page 14.
O
F
F
B
A
K
E
B
R
O
I
L
R
O
A
S
T
S
T
O
N
E
C
L
E
A
N
C
O
N
V
R
O
A
S
T
B
R
O
I
L
B
A
K
E
Cooking mode selector knob.
wolfappliance.com
|
13
Temperature Probe
The temperature probe measures the internal temperature
of food while cooking. It can be used with all cooking
modes except broil and convection broil.
Setting controls:
1 Rotate the mode selector knob to the desired cooking
mode.
2 Touch ENTER to select the preset temperature, or turn
the temperature control knob to change the temperature.
3 Insert the probe into the thickest area of food. When
making bread, cook for approximately 10 minutes before
inserting probe.
4 When preheat is complete, use a pot holder to lift the
probe receptacle cover, then insert the probe. Refer to
the illustration below.
5 The probe temperature is preset to 160°F (70°C). Touch
ENTER to select the preset temperature, or turn the
temperature control knob to change the temperature.
The display alternates between the oven set temperature
and the actual probe temperature. To alternate between
probe set point and actual probe temperature, press
PROBE. Temperatures below 70°F
(20°C) are displayed
as ‘Lo.’
6 An audible chime indicates the internal temperature has
reached the probe set point. Remove, then reinsert the
probe to verify internal temperature.
CAUTION
Probe and probe receptacle will be very hot. Handle
with care.
OVEN OPERATION
Proof
Setting controls:
1 Rotate the mode selector knob to BAKE.
2 Turn the temperature control knob left until ‘PrF’
appears, then release.
3 The oven temperature is preset to 85°F (30°C). Touch
ENTER to select the preset temperature, or turn the tem-
perature control knob to change the temperature. The
display alternates between the set temperature and ‘PrF.’
Dehydration
Accessory kit required. Accessories are avail able through an
authorized Wolf dealer. For local dealer information, visit the
nd a showroom section of our website, wolfappliance.com.
Setting controls:
1 Place the door stop supplied with accessory kit onto the
oven door lock.
2 Rotate the mode selector knob to CONV.
3 Turn the temperature control knob left until ‘dEH’
appears, then release.
4 The oven temperature is preset to 110°F (45°C). Touch
ENTER to select the preset temperature, or turn the
temperature control knob to change the temperature.
The display alternates between the set temperature and
‘dEH.’
Probe receptacle.
14
|
Wolf Customer Care 800.222.7820
OVEN OPERATION
Self-Clean
During self-clean, the oven is heated to an extremely high
temperature to burn off food soil. Remove all oven racks
and rack guides. They will discolor if left in during self-clean.
The oven door will lock and remain locked until self-clean is
complete and the oven temperature has cooled below 300°F
(150°C)
. Self-clean times include one hour for cool-down.
Setting controls for 4-hour self-clean:
1 Rotate the mode selector knob to CLEAN.
2 Touch ENTER.
Setting controls for 3-hour self-clean:
1 Rotate the mode selector knob to CLEAN.
2 Touch STOP TIME.
3 Touch the down arrow to reduce stop time by 1 hour.
4 Touch ENTER twice.
CAUTION
During self-clean, exterior surfaces may get hotter than
usual. Children should be kept away.
Auto Program
TIMED COOK
Timed cook automatically turns the oven off at a specied
time. The oven will begin to heat immediately and will turn
off at the desired stop time. The clock must be set to the
correct time for timed cook to function properly. Use in
any cooking mode except broil, convection broil, and bake
stone.
Setting controls:
1 Rotate the mode selector knob to the desired cooking
mode.
2 Touch ENTER to select the preset temperature, or turn
the temperature control knob to change the temperature.
3 Touch COOK TIME. Use the arrows to select desired
cook time in hours and minutes.
4 Touch ENTER.
DELAYED START
Delayed start automatically turns the oven on and off at
specied times. The oven will remain idle until the desired
start time and will turn off at the desired stop time. The
clock must be set to the correct time for delayed start to
function properly. Use in any cooking mode except broil,
convection broil, and bake stone.
Setting controls:
1 Rotate the mode selector knob to the desired cooking
mode.
2 Touch ENTER to select the preset temperature, or turn
the temperature control knob to change the temperature.
If ENTER is touched, the oven will begin to heat immedi-
ately but will enter idle mode once the stop time is set.
3 Touch COOK TIME. Use the arrows to select desired
cook time in hours and minutes.
4 Touch STOP TIME. Use the arrows to select desired time
oven should turn off.
5 Touch ENTER.
wolfappliance.com
|
15
OVEN OPERATION
Sabbath (oven only)
This appliance is certied by Star-K to meet strict religious
regulations in conjunction with specic instructions found
on www.star-k.org.
Sabbath overrides the automatic 12-hour shut off feature.
Sabbath must be reset after a power outage.
Setting controls:
1 Turn the oven light on or off.
2 Rotate the mode selector knob to BAKE or ROAST and
select desired temperature.
3 Touch and hold ENTER for 5 seconds. ‘SAb’ will appear
and ash on the oven control knob indicating Sabbath
mode has been initiated.
4 To change the oven temperature while in Sabbath
mode, turn the temperature control knob. Each turn will
increase or decrease the temperature by 10° (F or C).
The display and audible chime are disabled, but tem-
perature will randomly change after the new temperature
is selected. The oven will remain on until mode selector
knob is rotated to OFF.
Oven Light
WARNING
Verify power is disconnected from the electrical box
before replacing a light bulb.
Allow the oven to cool completely, then remove oven racks
and rack guides. To remove the light cover, gently pry the
bottom edge with a flat screwdriver. Remove the existing
bulb and replace with a 40-watt halogen bulb. Refer to the
illustration below.
LIGHT
COVER
Light bulb replacement.
16
|
Wolf Customer Care 800.222.7820
SURFACE OPERATION
Surface Operation
CONTROL PANEL
The control panel features illuminated touch controls that
are invisible when the cooking surface is off. A power level
indicator for each control displays the heat setting from SIM
(MLT) to HI. Each control is positioned to the corresponding
induction element. Refer to the illustration below.
Indicators on the control panel will illuminate to indicate
specic surface operation. Refer to the chart below.
INDICATORS
Control Panel Lock
Element(s) On
Hot Surface
Timer Set
Boost Mode
Front-to-Back Bridge
Side-to-Side Bridge (36" model only)
All Bridge (36" model only)
CAUTION
Do not place hot cookware directly over the control
panel.
CONTROL PANEL LOCK
The control panel lock feature prevents unwanted surface
operation. Touch and hold LOCK for three seconds to lock
and unlock the control panel.
will illuminate when the
control panel is locked.
The control panel will automatically lock after 10 minutes
of inactivity. This automatic lock feature can be disabled
through the extended options menu. Refer to page 19.
When the range is powered up for the rst time and after
a power outage, the induction surface will default to lock
mode.
Touch controls.
ELEMENT
CONTROL
wolfappliance.com
|
17
SURFACE OPERATION
Surface Operation
POWER LEVEL INDICATOR
When an element is activated, a power level indicator will
illuminate above the corresponding control indicating the
level of heat. The lowest heat is represented by the small
ame, varying levels of heat by additional indicators (dots),
and the highest heat by all indicators including the large
ame. Refer to the chart and illustration below.
SETTING POWER LEVEL USES
Melt 1 (small ame)
indicator
Melting butter and holding
chocolate and sauces.
Simmer 2–6 indicators Simmering sauces and
steaming rice.
Medium 6–7 indicators Making French toast and pan-
cakes and heating milk, cream
sauces, soups, and gravies.
Medium High 7-8 indicators Sauteing, browning, and frying.
High 8–10 (large ame)
indicators
Boiling water, searing meat,
and canning.
Power level indicator.
SINGLE ELEMENT | INNER ZONE
Setting controls:
1 To activate an induction element, touch ON/OFF for the
desired single element on the control panel. The power
level indicator will ash, and all indicators for that zone
will ash. Refer to the illustration below.
2 To complete the activation, touch HI for highest heat,
SIM (MLT) for lowest heat, BOOST to activate boost
mode, or the desired power level indicator.
3 To change heat setting while the element is on, touch or
slide to the desired power level.
4 To turn element off, touch ON/OFF.
IMPORTANT NOTE: If no cookware or incompatible cook-
ware is placed on an induction element after activation, the
control will ash for 30 seconds, then the element will turn
off automatically.
Element activation.
ON/OFF
18
|
Wolf Customer Care 800.222.7820
SURFACE OPERATION
Surface Operation
BOOST MODE
Boost mode boosts power on one element by diverting
power from an adjacent element. If the adjacent element is
on high, the power output will be reduced. The reduction in
power will be displayed on the power level indicator of the
adjacent element. Refer to the illustration below.
will
illuminate when an element is in boost mode.
Boost mode will deactivate automatically after approxi-
mately 15 minutes of continuous operation and can be
reactivated if desired.
BRIDGE ELEMENT
Setting controls:
1 To activate a bridge, select the desired power level on
one of the single elements.
2 Touch BRIDGE between corresponding element con-
trols to bridge elements front to back, BRG to bridge
elements side to side, or ALL BRIDGE to bridge all
elements.
, or will illuminate respectively.
3 To change the power level, adjust the power level on any
active bridged element.
4 To turn off, touch ON/OFF on any active bridged
element.
ALL BRIDGE should be used for cookware larger than
12"
(305) in diameter. For smaller cookware, use the right
rear element.
GRIDDLE USE
The bridge element provides an oblong heating area for use
with a griddle, open roaster, or sh poacher.
To preheat a griddle, set the bridge element power level to
high for ve minutes, then reduce for cooking.
CAUTION
A griddle, open roaster, or sh poacher should not be
used when the bridge element is off or with any other
combination of heating elements.
Boost mode.
BOOST
wolfappliance.com
|
19
SURFACE OPERATION
Surface Operation
TIMER
The surface timer can be set in one-minute increments up
to 99 minutes. Once a time is set,
will illuminate on the
surface control panel, and the countdown is visible on the
timer display. The timer is independent from the cooking
surface. Refer to the illustration below.
Setting timer:
1 Touch TIMER.
2 Touch and hold + or – until desired time is shown in the
timer display. Timer will begin the countdown in minutes.
3 Timer will chime with one minute left and will complete
the countdown in seconds.
4 When complete, the timer will chime and continue to
chime until TIMER is touched.
HOT SURFACE INDICATOR
will illuminate on the surface control panel and may
remain illuminated even when the induction surface is off.
ALL OFF
When one or more induction elements are on, will illu-
minate on the surface control panel. To turn off all elements
at the same time, touch ALL OFF. Refer to the illustration
below.
EXTENDED OPTIONS
The extended options feature allows the user to set pref-
erences for volume, tone, and surface control panel lock
feature.
Setting adjustment:
1 While the unit is off and unlocked, touch and hold ALL
OFF for ve seconds.
2 Power level 1 on the rear element control will be dis-
played and ‘VO’ will appear on the timer display.
Touch SIM (MLT) or HI on the front element control to
adjust volume.
3 Touch + on the timer control to adjust tone. Power level
2 on the rear element control will be displayed, and ‘Fr’
will appear on the timer display.
Touch SIM (MLT) or HI on the front element control to
adjust tone.
4 Touch + on the timer control to adjust the automatic
control panel lock. Power level 3 on the rear element
control will be displayed, and ‘Lo’ will appear on the
timer display.
Touch SIM (MLT) or HI on the front element control to
turn the automatic lock feature off or on respectively.
5 Touch ALL OFF at any time while in extended options to
conrm settings and return to idle.
Timer controls.
All off.
TIMER
ALL OFF
20
|
Wolf Customer Care 800.222.7820
CARE RECOMMENDATIONS
Care Recommendations
CLEANING
Stainless steel Use a nonabrasive stainless steel cleaner and apply with a soft lint-free cloth. To bring out the natural luster,
lightly wipe surface with a water-dampened microber cloth followed by a dry polishing chamois. Always
follow the grain of the stainless steel.
Glass-ceramic surface Allow to cool. Use a spray degreaser to remove ngerprints and a non-abrasive Ceran® cooktop cleaner for
food soil. Do not allow any item that could melt to come in contact with the glass-ceramic surface when hot.
If this occurs, use the razor blade scraper provided with the range to remove.
Control panel Use a spray degreaser to remove ngerprints and food soil. Spray on a cloth before wiping the panel.
IMPORTANT NOTE: Do not spray cleaners directly on the control panel.
Control knobs Using a damp cloth, wipe with a mild detergent or spray degreaser. Rinse and dry. Do not place in the
dishwasher.
Oven rack guides Remove and place on a at surface near the sink. Clean with hot water and mild detergent or paste of
baking soda and water. Do not immerse in water. Towel dry.
Oven interior Before using the self-clean feature, use a razor blade to gently lift baked-on foods from the oven cavity
and window. For stubborn stains, spray with a mild abrasive cleaner, or spray degreaser and scrub with a
no-scratch Scotch-Brite™ pad (pink or blue). Wash the entire oven cavity with soap and water to remove
cleaning chemicals before entering self-clean mode. If residue is not cleaned from the cavity, etching of the
porcelain may occur. Once the self-clean cycle is complete, allow the oven to cool completely and wipe out
ash with a damp cloth.
Broiler pan To clean the upper rack, use a mild detergent and scouring pad. Rinse and dry. To clean the bottom pan,
discard grease and wash with hot water and mild detergent. Rinse and dry. The stainless steel upper rack is
dishwasher safe. However, do not place any porcelain-coated rack or pan in the dishwasher.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Sub-Zero IR304TE/S/TH Mode d'emploi

Catégorie
Micro-ondes
Taper
Mode d'emploi
Ce manuel convient également à