Fisher & Paykel CP-486GL Manuel utilisateur

CP SERIES PROFESSIONAL GAS COOKTOP

Installation Guide

MODELS:

CP-366

CP-364GL

CP-364GD

CP-484GG

CP-485GD

CP-486GL

CP-486GD

A MESSAGE TO OUR CUSTOMERS

1

Thank you for selecting this DCS professional Cooktop. Because of this appliance’s unique features we have

developed this Installation Guide. It contains valuable information on how to properly install your new appliance

for years of safe and enjoyable cooking.

F

or your convenience, product questions can be answered by a DCS Customer Care Representative

by phone: 1-888-281-5698, email: [email protected],

or by mail:

Fisher & Paykel Appliances, Inc.

Attention: DCS Customer Care

5900 Skylab Road

Huntington Beach, CA 92647 www.dcsappliances.com

WARNING

Improper installation, adjustment alteration, service or maintenance can cause property damage, injury or death.

Read the installation, operating and maintenance instructions thoroughly before use, installing or servicing this

equipment.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result causing property damage,

personal injury or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

DANGER

I

f You Smell Gas:

1. Do not try to light any appliance.

2. Do not touch any electrical switch; do not use any phone in your building.

3.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

4. If you cannot reach your gas supplier, call the fire department.

5. Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING

T

o r

educ

e the risk of injur

y t

o persons in the event of a cooktop grease fire, observe the following: Turn burner off

first

. Smother flames with a close

-fitting lid

, c

ook

ie sheet

, metal tr

a

y

, baking soda or use a dry chemical or foam-type

fir

e extinguisher. Be careful to prevent burns. If the flames do not go out immediately evacuate and call the fire

depar

tmen

t

. Nev

er pick up a flaming pan -

You may be burned. DO NOT USE WATER ON GREASE FIRES, including

w

et dishcloths or t

o

w

els - a violen

t st

eam e

xplosion will r

esult

. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The fire is small and contained in the area where it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NOTE: Please write the Model and Serial Number on this page for references (located on the rating plate behind

the unit right side)

MODEL NUMBER

SERIAL NUMBER

2

TABLE OF CONTENTS

INTRODUCTION 3

SAFETY PRACTICES AND PRECAUTIONS 4-6

MODELS 7

PLANNING THE INSTALLATION 8-9

UNPACKING AND HANDLING 9-10

VENTILATION REQUIREMENTS 11

CABINET PREPARATION 12-14

BACKGUARD INSTALLATION 15

ELECTRICAL CONNECTIONS 15

GAS HOOK-UP 16

TEST AND ADJUSTMENTS 17

CLEANING EXTERIOR SURFACES 18

INSTALLER FINAL CHECKLIST 19

HOW TO OBTAIN SERVICE 20

WARRANTY 21-22

3

INTRODUCTION

The DCS Professional CP Cooktops feature a large number of features varying with each model. All models

f

eature a minimum of 4 surface burners, with the option of up to 6 surface burners on all models. All of the 48"

and 36" Cooktops feature the possibility of various grill and griddle combinations. All cooktop models require

t

he installation of one of the two offered backguards, if installed with less than 12” of clearance to combustible

material. See page 14.

IMPORTANT INSTALLATION INFORMATION

The cooktops are tested in accordance with ANSI Z21.1 Standard for Household Cooking Gas Appliances. These

cooktops must be installed in conjunction with a suitable overhead vent hood. (See ventilation requirements).

Due to the professional high heat capacity of this unit, particular attention should be paid to the hood and duct

work installation to ensure it meets local building codes. To eliminate risk of burns or fire by reaching over

heated surface units, cabinet storage located above the surface units should be avoided.

Check local building codes for the proper method of cooktop installation. Local codes vary. Installation,

electrical connections, and grounding must comply with all applicable codes. In the absence of local codes, the

cooktop should be installed accordance with the National Fuel Gas Code ANSI Z223.1 and National Electrical

Code ANSI / NFPA 70. Be sure that the unit being installed is set up for the kind of gas being used. The gas

cooktop is shipped from the factory set and adjusted for natural gas or LP (propane), depending on the specific

model ordered.

Verify that the cooktop is compatible with gas supply at the installation site before

proceeding further. Return cooktop to dealer if unit is not set for site gas supply.

4

SAFETY PRACTICES AND PRECAUTIONS

When properly cared for, your new DCS Appliance has been designed to be a safe, reliable cooking appliance.

When using this restaurant caliber appliance, use it with extreme care, as this type appliance provides intense

heat and can increase the accident potential. Basic safety precautions must be followed when using kitchen

a

ppliances, including the following:

■

R

ead the Use and Care Manual, which came with this appliance, thoroughly before using your new appliance.

This will help to reduce the risk of fire, electric shock, or injury to persons.

■

Begin by insuring proper installation and servicing. Follow the installation instructions in this manual. Be sure to

have a qualified technician install and ground this appliance before using.

■

Have the installer show you where the gas supply shut-off valve is located so you will know how and where to

turn off the gas to the appliance.

■

If you smell gas, the installer has not done a proper job of checking for leaks. You can have a small leak and

therefore a faint gas smell if the connections are not completely tight. Finding a gas leak is not a “do-it-yourself”

procedure. Some leaks can only be found with the burner control in the ON position and for your protection it

must be done by a qualified service technician.

■

If by some chance a burner goes out and gas escapes, open a window or a door to let the room air out. Do not

attempt to use the appliance until the gas has had time to dissipate. Follow the instructions on page 1, “For

your safety – if you smell gas”.

■

This appliance has been factory assembled for natural or LP gas. It should be correctly adjusted from the factory

for the type of gas that is used.

■

Do not repair or replace any part of this appliance unless it is specifically recommended in this manual. All other

servicing should be referred to a qualified technician.

■

Children should not be left alone or unattended in an area where appliances are in use. They should never be

allowed to turn knobs, push buttons, sit or stand on any part of an appliance while in operation.

WARNING:

Do not store items of interest to children above or at the back of any appliance. Children could be seriously injured

if they should climb onto the appliance to reach these items.

■

Never store anything on the cooktop. Flammable materials can catch fire, plastic items may melt or ignite and

other types of items could be ruined.

■

Do not hang articles from any part of the appliance or place anything against the oven. Some fabrics are quite

flammable and may catch on fire.

■

If the appliance is near a window be certain the curtains do not blow over or near the cooktop burners; they

could catch on fire.

■

Do not use water on grease fires. Turn all burners OFF, then smother fire with baking soda or use a dry chemical

or foam-type fire extinguisher.

■

Never let clothing, pot holders, or other flammable materials come in contact with, or too close to, any burner or

burner grate until it has cooled. Fabric may ignite and result in personal injury.

■

Be certain to use only dry pot holders: moist or damp pot holders on hot surfaces may cause burns from steam.

Do not use a towel or other bulky cloth in place of pot holders. Do not let pot holders touch hot burners, or

burner grates.

■

For personal safety, wear proper apparel. Loose fitting garments or hanging sleeves should never be worn while

using this appliance. Some synthetic fabrics are highly flammable and should not be worn while cooking.

5

SAFETY PRACTICES AND PRECAUTIONS

■ Do not use aluminum foil to line any part of the cooktop. Doing so, heat will be trapped underneath it. This

t

rapped heat can upset the cooking performance and can damage the finish of the cooktop parts.

■ This appliance is for cooking. Never use the cooktop to warm or heat a room. This could damage the cooktop.

■

When using the cooktop: Do not touch the burner grates or the immediate surrounding area. Areas adjacent to

the burners may become hot enough to cause burns.

■

Never leave the cooktop unattended when using high flame settings. When cooking with high flame settings,

boil overs may cause smoking and greasy spill overs may ignite. More importantly, if the burner flames are

smothered by a severe boil over which effects the igniter, unburned gas will escape into the room.

■

Only certain types of glass, heat-proof glass-ceramic, ceramic, earthen ware, or other glazes utensils are suitable

for cooktop use. This type of utensil may break with sudden temperature changes. Use only on low or medium

flames settings according to the manufacturer’s directions. The use of professional utensils is recommended.

■

Do not heat unopened food containers; a build up of pressure may cause the container to burst.

■

During cooking, set the burner control so that the flame heats only the bottom of the pan and does not extend

beyond the bottom of the pan. This could heat and/or melt the handles, and may increase cooking time.

■

Always use utensils that have flat bottoms large enough to cover the burner. The use of undersized utensils will

expose a portion of the flame to direct contact and may result in ignition of clothing.

■

To minimize burns, ignition of flammable materials and unintentional spill overs, position handles of utensils

inward so they do not extend over adjacent work areas, cooking areas, or the edge of the cooktop.

■

Hold the handle of the pan to prevent movement of the utensil when stirring or turning food.

■

Grease is flammable. Let hot grease cool before attempting to handle it. Avoid letting grease deposits collect

around the cooktop burners. Clean after each use or boil over.

■

For proper lighting and performance of the cooktop burners, keep the burner ports clean. It may be necessary to

clean these when there is a boil over or when the burner does not light, even though the electronic igniters

click.

■

Do not use the grill for cooking excessively fatty meats or products which promote flare-ups. Do not use

cooking utensils on the grill.

WARNING! NEVER use this appliance as a space heater to heat or warm the room.

Doing so may result in carbon monoxide poisoning.

6

SAFETY PRACTICES AND PRECAUTIONS

■

Clean the cooktop with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the cooktop

while it is hot. Some cleaners produce noxious fumes if applied to a hot surface. Follow directions provided by

the cleaner manufacturer.

■

Be sure all the cooktop controls are turned off and the appliance is cool before using any type of aerosol cleaner

on or around the appliance. The chemical that produces the spraying action could, in the presence of heat,

ignite or cause metal parts to corrode.

■

Clean the ventilator hood and filters above the cooktop frequently so grease from cooking vapors does not

accumulate on them.

■

Turn the ventilator OFF in case of fire or when intentionally “flaming” liquor or other spirits on the cooktop. The

blower, if in operation, could unsafely spread the flames.

■

DO NOT obstruct the flow of combustion or ventilation air to the appliance. Be sure a fresh air supply is

available.

■

For safety reasons and to avoid damage to the appliance never sit, stand, or lean on the cooking surface.

■

Service should only be done by authorized technicians. Technicians must disconnect the power supply before

servicing this appliance.

WARNING:

California Proposition 65 - The burning of gas cooking fuel generates some by-products which are known by the

State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of

potential exposure to such substances. To minimize exposure to these substances, always operate this unit

according to the instructions contained in this booklet and provide good ventilation to the room when cooking with

gas.

RECOMMENDATIONS ON HOOK-UP TO GAS SUPPLY:

A manual valve must be installed external to the appliance, in an accessible location from the front for the

purpose of shutting off the gas supply. The supply line must not protrude beyond the back of the unit. Make

sure the gas supply is turned off at the wall valve before connecting the appliance.

The gas supply connections should be made by a qualified technician and in accordance with local codes or

ordinances. In the absence of a local code, the installation must conform to the latest edition of National Fuel

Gas Code ANSI Z223.1.

NOTE:

This pro

duct m

ust b

e installed b

y a lic

ensed plumber or gas fitter when installed within the Commonwealth of

Massachusetts.

NOTE:

(mandatory for the State of Massachusetts)

Alternate method of supplying gas must be installed

into the unit.

Installer supplied shut-oﬀ valve

must be easily accessible inside

cabinetry.

Gas Supply

MODELS

7

48” CP COOKTOP MODELS

CP-484GG

36” CP COOKTOP MODELS

CP-366

CP-486GL CP-486GD

CP-485GD

CP-364GL CP-364GD

8

PLANNING THE INSTALLATION

IMPORTANT INSTALLATION INFORMATION

A

ll cooktop models with less than a 12” clearance between combustable material and the back edge of the

cooktop, require the installation of one of the two offered Wall Mount Backguards – see page 15.

FIG. 1

30”

12”

Wall Mount Full

Backguard

Wall Mount

Low Backguard

15/16”

Model Number

Low

Back

guard

Full

Back

guard

48” Cooktop BGC-1248 BGC-3048

36” Cooktop BGC-1236 BGC-3036

9

PLANNING THE INSTALLATION

RECOMMENDED INSTALLATION INSTRUCTION

Install components in the following order:

A. Vent Hood

B. Backguard System (sold separately)

C

. Cooktop

1. Locate cooktop according to cooktop installation instructions.

2. Measure distance from counter surface to top of trim on cooktop adding 1/8” for backguard clearance.

3. Transfer this measurement to the wall. This will mark the bottom of your backguard.

4. From this line measure 30-1/16” up wall to mark top of 30” backguard. This is the minimum height that the

bottom of your vent hood can be installed.

5. Follow vent hood manufacturer’s installation instructions to install vent hood.

6. Follow backguard installation instructions to install backguard.

7. Connect gas and electric connections and slide cooktop into position.

NOTE:

A manual gas supply valve must be installed. See page 16.

CAUTION:

Proper equipment and adequate manpower must be used in moving the cooktop to avoid personal injury or

damage t

o the unit.

MOVING AND PLACING THE COOKTOP

The cooktops have a shipping weight of approximately 228 pounds (36" models) and 324 pounds (48" models).

After removal of packing materials, it is recommended that the grates and drip pan (below knobs) be removed to

facilitate handling. This will reduce the weight to about 150 pounds.

■

DO NOT REMOVE THE GRILL OR GRIDDLE ASSEMBLIES.

NOTE:

If a solid side cabinet wall exists on one or both sides, you will need to notch the front corner of the cabinet to match the

c

ounter top notch and to provide clearance for the cooktop front (see page 14).

It may be necessary to remove the cooktop knobs to pass through some doorways. With the knobs removed a

29-3/8" wide opening is required. Remove the outer carton and packing material from the shipping base. The

cooktop is held to the skid by four straps. After removing the straps, the cooktop must be lifted and removed

from the skid.

UNPACKING AND HANDLING

10

UNPACKING AND HANDLING

■

The professional cooktop should be moved close to

its final location. Electric and gas connections should

be made (pgs. 15 & 16) and the backguard installed

(

as required, pg. 8 & 15) before the cooktop is placed

in its final position. The grill and griddle sections are

f

astened in place at the front with screws. They are

designed to be stationary and not meant to be

removed for cleaning. The griddle has two leveling

screws beneath the rear flue cover which can be used

to adjust the griddle to the desired slope. The center

screw is for shipping and should be removed. See

Fig. 2.

ANCHORING THE COOKTOP

■

Due to the weight of the cooktop, along with a built-

in side frame gasket that is meant to rest and create

a seal on the counter top once installed, it is not

necessary to anchor the unit to the counter.

Fig. 2

Shipping Screw

(remove)

Outer Leveling

Screws (2)

Griddle Flue Cover

11

VENTILATION REQUIREMENTS

A suitable exhaust hood must be installed above the range. The following chart indicates the minimum blower

capacity recommended for hood ventilation.

* When installing a unit featuring a grill, GL models, requires a 1200 CFM ventilation unit.

CAUTION:

Ventilation hoods and blowers are designed for use with single wall ducting. However, some local building codes or

inspectors may require double wall ducting and/or damper. Consult local building codes and/or local agencies,

before starting, to ensure that hood and duct installation will meet local requirements.

Hood blower speeds should be variable to reduce noise and loss of heated or air conditioned household air

when maximum ventilation is not required. Normally, the maximum blower speed is only required when using

the grill.

For best smoke elimination, the lower edge of the hood should be installed a minimum of 30" to a maximum of

36" above the cooktop cooking surface, (page 12). If the hood contains any combustible materials (i.e. a wood

covering) it must be a minimum of 36" above the cooking surface.

Due to a high volume of ventilation air, a source of make-up air (outside replacement air) is recommended. This

is particularly important for tightly sealed and insulated homes. A reputable heating and ventilating contractor

should be consulted.

Ventilation Unit

Standard Counter

Installation

Recommendatons

Island Installation

Recommendatons

HOOD 24" Deep x Unit Width 30" Deep x 36" at Bottom

BLOWER

48” Cooktop

1200 CFM

*36” Cooktop

600-1200 CFM

12

CABINET PREPARATION

1

. To ensure professional results, the cabinet and countertop openings should be prepared by a qualified cabinet

worker. We recommend having the cooktop available before cutting the opening for more precise dimension

v

erification.

2. The clearances shown in Fig. 8 pg. 14 are required for all types of backguard installations.

3. The cooktop is designed to hang from the countertop from its rear and side flanges. The countertop, however,

must be strong enough to support this heavy cooktop. It may be necessary to add a supporting cleat along each

side or another form of support such as a 2” x 4” corner brace on each side, or a deck to set the cooktop on.

See Fig. 3 & 5.

4. The cooktop can be installed in various positions with the front either flush or projecting, depending on the

countertop depth. See Fig. 4 & Fig. 7 (cooktop side view).

5. Establish the centerline of the desired cooktop location. It should be the same as the center of the overhead

ventilation hood.

G

H

F

D

E

Min. 48" Wide Hood

Min. 36" Wide Hood

J

16"

Electrical and

Gas Supply.

2"

13"

Max.

12" Min. to

Combustible

Material#,

Each Side

CAUTION

36" Min. to

combustible

material#, from

cooking surface

Cooking Surface

2" x 4" corner

support (if required)

18" Min.

A

C

B

# As deﬁned in the “National Fuel Gas Code” (ANSI Z223.1, lastest edition).

The horizontal surfaces of the cooktop trim must not be below

countertop level.

30" Min.

36" Max.

for best smoke

elimination

Fig. 3

M

odels ABCDEFGHJ

CP-48 Models 47-7/8” 26-1/2” 8-7/16” 46-5/16” 22-3/4” 8” 7/8” 0 ~ 2-1/2” 17”

CP-36 Models 35-7/8” 26-1/2 ” 8-7/16 ” 34-15/16” 22-3/4” 8” 1/2” 0 ~ 2-1/2” 7”

CABINET PREPARATION

13

6. Cut the openings for the following installation:

■ Standard counter top installation, see Fig. 8A

■ Deep counter or island installation, see Fig. 8B

NOTE:

If the deck is used, the sides or bottom of the cutout may be solid

combustible or non-combustible material. If the bottom is solid, provide

a 6" x 6" cutout in the left rear corner for the gas inlet and power cord

clearance. See Fig. 6.

Flush with cabinets

Front projects outward as shown

from standard depth cabinet.

Front flush with cabinets; a minimum

of 25

3/4" cabinet depth required

Fig. 4

Front flush with cabinets; a minimum of 25-3/4”

cabinet depth required

Front projects outward as shown

from standard depth cabinet.

Flush with cabinets

Counter-Sunk Screws

Fig. 5

Counter-Sunk Screws

Fig. 6

6

Cutout

CABINET PREPARATION

14

8-7/16"

2

2-3/4"

26-1/2"

23-1/4"

3" To Center Line

of Gas Inlet

1/2"

5/8"

Cabinet face for installation

with projecting control panel

Cabinet face for installation

with ﬂush control panel

2-1/2"

C

ountertop level

#

Fig. 7

30"

26-1/2"

12" Min. to Combustibles

#

without Backguard

15/16"

12"

Wall Mount

Low Backguard

Base Cabinet

Wall Mount

Full Backguard

36” Min. to

Combustibles

#

36” Min. to

Combustibles

#

As deﬁned in the “National Fuel Gas Code” (ANSI Z223.1, lastest edition).

Fig. 8

A B

ELECTRICAL CONNECTIONS

15

ELECTRICAL REQUIREMENTS

■

120 VAC, 60 Hz., single phase

■

CP-48: 15 Amp. Max. (use 15 Amp. circuit)

■

CP-36: 15 Amp. Max. (use 15 Amp. circuit)

Always disconnect electric supply cord from the wall outlet or service

disconnect before servicing this appliance. Observe all governing codes

and ordinances when grounding, in absence of which, observe National

Electrical Code ANSI / NFPA No. 70.

RECOMMENDED GROUNDING METHOD

This appliance is factory equipped with a power supply cord with a

three-prong grounding plug (with polarized parallel blades). It must be

plugged into a mating grounding type receptacle, connected to a

correctly polarized 120 Volt circuit. If the circuit does not have a

grounding type receptacle, it is the responsibility and obligation of the

installer to have the existing receptacle changed to a properly grounded and polarized receptacle in accordance

with all applicable local codes and ordinances by a qualified electrician. In the absence of local codes and

ordinances, the receptacle replacement shall be in accordance with the National Electrical Code.

Note:

The third prong should not, under ANY circumstances, be cut or removed.

Receptacle Box

Cover Plate

Three Prong

Receptacle

Three

Prong

Plug

Fig. 10

Fig. 9

BACKGUARD INSTALLATION

T

he backguard is located as shown in Fig. 9. Secure the

backguard to the wall behind the range. Specific

instructions for installation of the full backguard or low

backguard can be found packaged with the backguard.

See also page 8, “Planning The Installation” section. A

b

ackguard must be installed when there is less than a

12” clearance between combustibles and the back of

the range (above the cooking surface). See fig. 8.

DCS backguards are sold separately.

12"

30"

15/16"

Wall Mount

Full Backguard

(

Model #’s BGC-3036, BGC-3048)

Wall Mount

Low Backguard

(

Model #’s BGC-1236, BGC-1248)

16

GAS REQUIREMENTS

Verify the type of gas supplied to the location. The cooktop is shipped from the factory set up and adjusted for

Natural Gas or LP (propane), depending on the specific model ordered.

Verify that the cooktop is compatible

with gas supply at the installation site before proceeding further.

Return the cooktop to the dealer if the unit is

not set for the gas supplied at the site.

NATURAL GAS

■ Connection: 1/2” NPT Minimum 5/8” dia. flex line. ■ Supply Pressure: 6” to 14” W.C.

LP GAS

■ Connection: 1/2” NPT Minimum 5/8 dia. flex line. ■ Supply Pressure: 11” to 14” W.C.

A regulator is required at the LP source to provide a maximum of 14” W.C. to the cooktop regulator.

HOOK-UP TO GAS SUPPLY

A manual valve must be installed external to the appliance, in an

accessible location from the front for the purpose of shutting off the

gas supply (Fig. 11). Make sure the gas supply is turned off at the

wall valve before connecting the appliance. The gas supply

connections should be made by a qualified technician and in

accordance with local codes or ordinances. In the absence of a local

code, the installation must conform to the latest edition of National

Fuel Gas Code ANSI Z223.1.

To prepare the unit for connection to the gas supply, thread the

supplied 1/2” pipe nipple into the elbow on the end of the manifold.

The elbow is located inside the chassis of the unit, on the end of the

manifold, facing down. See fig.12. It is accessible through the

square cutout in the left rear corner of the chassis bottom. Connect

the outlet of the regulator to the exposed end of the nipple, connect

the flex line from the gas supply to the inlet side of the regulator.

NOTE:

Pipe seals must be used on all pipe threads.

CAUTION:

T

he appliance must be isolated from the building’s gas

supply piping system by closing its individual manual

shut-off valve during any pressure testing of the gas

supply piping sy

stem at test pressures equal to or less

than 1/2 psig (3.5kPa.). The appliance and its

individual shut-off valve must be disconnected from

the gas supply piping sy

stem during any pressure

testing of the system at the test pressures in excess of

1/2 psig (3.5kPa.). When checking the manifold gas

pressure, the inlet pressure to the regulator should be

at least 7.0”W.C. for natural gas or 12.0” for LP.

NOTE:

The arrow on the regulator indicating direction of gas

flow should be pointing towards the unit. The flex line

for the gas supply must be metal and be approved by an

approved certif

ying agenc

y (

A

GA, CGA, or UL). Never use

a hose made of rubb

er or other synthetic material, as the

heat may cause the hose t

o melt and dev

elop leaks

.

GAS HOOK-UP

Fig. 12

*Installation must conform with

local codes or with the National

Fuel Gas Code ANSI Z223.1 or

the CAN/CGA-B149.2 Propane

Installation Code

Coupling

1/2 NPT black

1/2 NPT

Close Nipple

Regulator

LP/NG (included)

Adapter 1/2 NPT

to 3/8 ﬂare ﬁtting

Do not put threading

compound on these

threads

Bottom of unit

Threading compound

must be resistant to LP gas

1/2 x 5" NPT

Close

Nipple

Installer supplied shut-oﬀ

valve must be easily

accessible*

Fig. 11

Flex Line to Cooktop

Manual Shut-Off

Valve must be

Easily Accessible

!

17

TEST AND ADJUSTMENTS

WARNING:

F

or warranty coverage, DCS requires that burner adjustments be made by a

qualified technician at the time of installation. Extreme care should be used

when adjustments are made after installation.

COOKTOP BURNERS

The cooktop burners are not adjustable. Proper operation is achieved when

the correct orifices for gas supply are installed at the factory, based on model

ordered.

When installing the burner port ring, be sure that the two locating pins in the

bottom side of the brass port ring are properly aligned with the locating notch

and center holes on the top side of the simmer ring. Incorrect alignment will

produce a potentially dangerous flame and poor burner performance.

Note:

No air shutter adjustment is possible on the cooktop burners. Burner flames should

be blue and stable with no yellow-tipping (some yellow-tipping is normal with LP

gas), excessive noise, or lifting of flame from the burner (Fig. 13).

COOKTOP BURNER LIGHTING NOTE

The cooktop burners have an infinite number of heat settings and there are no fixed positions on the control

knobs between HI and LO. To turn the cooktop burner on, push in on the control knob and turn it counter-

clockwise to the “LITE” position. An audible clicking sound will be heard. When the gas has been ignited by the

electronic spark igniter, turn the knob to the desired setting (Fig. 14).

Note:

The igniter will continue to click until a flame is present. If the cooktop burner

does not ignite, check the spark igniter by listening for a clicking sound. If you

do not hear the igniter click, turn off the burner. Check for a tripped circuit

breaker, blown fuse, or poor wire connection to the igniter.

WARNING:

When turning on any cooktop burner, be sure to stop at the “LITE” position

bef

or

e turning the burner t

o a flame setting f

or cooking. If the burner is not

lit and it is turned beyond the “LITE” position, to HI, MEDIUM, or LO, there

will be a burst of flame when the burner does ligh

t

. This could cause burns

or damage t

o the surr

ounding c

oun

t

er

top.

THIS ADJUSTMENT SECTION APPLIES TO THE GRIDDLE

AND GRILL BURNERS.

Check for the proper burner flame characteristics and adjust air shutters if

necessary (fig. 15). Each valve and air shutter is individually tested and

adjusted prior to shipment. Normally adjustment is not required,

however, vibration during transit, gas conversion or variations in the local

gas supply may make minor adjustments necessary. Burner flames should

be blue and stable with no yellow tips, excessive noise or lifting of the

flame from the burner. If any of these conditions exist, check that the air

shutter or burner ports are not blocked. If this condition persists, adjust

the air shutter as required. If the flame is too yellow, indicating insufficient air, adjust the shutter counter-

clockwise to increase air inlet. If the flame is noisy or tends to lift away from the burner, indicating too much

air, turn the shutter clockwise to reduce air. The griddle flames should be 1-1/2" to 2". The grill burner flames

should be 3/8” to 5/8” (fig. 16).

1-1/2"

COOKTOP BURNER

FIG. 13

FIG. 14

SIM

LO

LITE

HI

OFF

Fig. 15

1-1/2" ~ 2"

Typical Section of Proper Flame

3/8" ~ 5/8"

(Grill)

(Griddle)

Fig. 16

Typical Section of Proper Flame

Griddle

1-1/2” – 2”

3/8” – 5/8”

Grill

air shutter

18

CLEANING EXTERIOR SURFACES

The stainless steel surfaces may be cleaned by wiping with a damp soapy cloth or sponge. Any liquid soap (like

Dawn or Stainless Steel Magic) will remove fingerprints and smears. Do not use steel wool as it will scratch this

surface.

La page est en cours de chargement...

Fisher & Paykel CP-486GL Manuel utilisateur

Fisher & Paykel CP-486GL Manuel utilisateur

dans d''autres langues

Autres documents