Indesit XWE 71483X W EU.1 Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
1
GB
WASHING MACHINE
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9-10
Table of wash cycles
Wash options
Push & Wash
Detergents and laundry, 11-12
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13
Service, 14
XWE 71483
English,1
GB
FR
Français,15
NL
Nederlands,29
DE
PL
SR
Deutsch,43
Polski,57
Cрпски,71
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with the
installation process.
3. Remov e t h e 4
protective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not
p e r f e c t l y l e v e l ,
c o m p e n s a t e f o r
any unevenness by
tightening or loosening
the adjustable front
feet (see figure); the
angle of inclination,
measured in relation
to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it
to a cold water tap
using a ¾ gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2 . C o n n e c t t h e
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand side
of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening
the duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
•the socketisearthed and complies with all
applicable laws;
•thesocketisabletowithstandthemaximum
power load of the appliance as indicated in the
Technical data table (see opposite);
•thepowersupplyvoltagefallswithinthevalues
indicated in the Technical data table (see
opposite);
•the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle
with detergent and no laundry, using the wash
cycle “Auto Clean” (see “Cleaning the washing
machine”).
65 - 100 cm
Technical data
Model
XWE 71483
Dimensions
width 59.5 cm
height 85 cm
depth 54 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water
connections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1400 rotations per minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
and
1015/2010
Programme 8:
Cotton Standard 60°.
Programme 9:
Cotton Standard 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU - WEEE
4
GB
Care and maintenance
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such
as coins or buttons) may fall into the protective
pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. Take off the cover
panel on the front
of the machine by
first pressing it in
the centre and then
pushing downwards
on both sides until
you can remove it
(see figures).
2. Unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Cutting off the water and electricity
supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system inside
the washing machine and help to prevent leaks.
•Unplugthewashingmachinewhencleaningit
and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasa“AutoClean”
programme for its internal parts that must be
run with no load in the drum.
For maximum performance you may want
to use either the detergent (i.e. a quantity
10% the quantity specified for lightly-soiled
garments) or special additives to clean the
washing machine. We recommend running a
cleaning programme every 40 wash cycles.
To start the programme press buttons A and
B simultaneously for 5 seconds (see figure).
The programme will start automatically and
will last approximately 70 minutes. To stop the
cycle press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
To remove the drawer,
press lever (1) and pull
the drawer outwards
(2) (see figure).
Wash it under running
water; this procedure
should be repeated
frequently.
Caring for the door and drum of your
appliance
•Alwaysleavetheportholedoorajarinorderto
prevent unpleasant odours from forming.
2
1
1
2
3
A
B
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
•Thisappliancewasdesignedfordomesticuseonly.
•Thisappliancecanbeusedbychildren
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
•Thewashingmachinemustonlybeusedbyadults,in
accordance with the instructions provided in this manual.
•Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
•Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
•Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
•Donottouchthedrainedwaterasitmayreach
extremely high temperatures.
•Neverforcetheportholedoor.Thiscoulddamagethe
safety lock mechanism designed to prevent accidental
opening.
•Iftheappliancebreaksdown,donotunderany
circumstances access the internal mechanisms in an
attempt to repair it yourself.
•Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
•Thedoorcanbecomequitehotduringthewashcycle.
•Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
•Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EU-WEEEonWaste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if
it is not, remove excess
water using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. remove the cover panel
on the lower front part of
the washing machine (see
figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
1
2
3
6
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button
and indicator light
DELAYED
START
button
OPTION
buttons
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
PUSH & WASH button: (see “Wash cycles and options”).
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of wash cycles”).
OPTION buttons: press to select the available options.
The indicator light corresponding to the selected option will
remain lit.
TEMPERATURE button: press to reduce or
completely exclude the temperature; the value appears on
the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAYED START button: press to set a delayed
start for the selected wash cycle; the delay period appears
on the display.
START/PAUSE button and indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the indicator
light will remain lit in a fixed manner. To pause the wash
cycle, press the button again; the indicator light will flash
in an amber colour. If the symbol is not illuminated, the
door may be opened. To start the wash cycle from the
point at which it was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
DISPLAY
PUSH & WASH
button
7
GB
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED
START option has been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of
10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon
will then switch off approximately 1 minute after the final amount of time remaining has appeared.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin
Drain
The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.
There are three levels in section C concerning the washing options.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
Display
B
C
A
C
8
GB
Running a wash cycle
Rapid programming
1. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
2. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the
relevant compartments as described in “Detergents and
laundry”.
3. CLOSE THE DOOR.
4. Press the “PUSH & WASH” button to start the wash
programme.
Traditional programming
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the relevant
compartments as described inDetergents and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the 8 programme is selected, the
temperature can be increased up to a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Modify the cycle settings.
• Pressthebuttontoenabletheoption;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisabletheoption;the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with another
previously selected option, the indicator light will
flash accompanied by a buzzer (3 beeps), and only
the latter option will be activated; the indicator light
corresponding to the activated option will turn on.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will be lit).
To change a wash cycle while it is in progress, pause
the washing machine using the START/PAUSE button
(the START/PAUSE indicator light will flash slowly in an
amber colour); then select the desired cycle and press
the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Table of wash cycles
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 8 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 9 with a temperature of 40°C.
3) Synthetic program along: set wash cycle 10 with a temperature of 40°C.
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle duration
Prewash
Wash
Fabric
softener
Bleach
Special
1
Sport
30° 600 -
- 3,5 - - - 55’
2
Dark
30° 800 -
- 4 - - - 70’
3
Anti-odour (Cotton) 60° 1000 -
- 3,5 - - - 110’
3
Anti-odour (Synthetic) 40° 1000 -
- 3,5 - - - 100’
4
Delicate
30° 0 -
- 1 - - - 80’
5
Wool: for wool, cashmere, etc. 40° 800 -
- 1,5 - - - 70’
6
Duvet: for down-stuffed garments. 30° 1000 -
- 2 - - - 110’
Standard
7
Cottons with Pre-wash: extremely soiled whites. 90° 1400
- 7 53 2,15 86 170’
8
Cotton Standard 60°C (1): heavily soiled whites and resistant colours.
60°
(Max. 90°)
1400 -
- 7 53 0,94 52,5 160’
9
Cotton Standard 40°C (2): lightly soiled whites and delicate colours.
40° 1400 -
- 7 53 0,93 85 140’
10
Synthetic: heavily soiled resistant colours. 60° 800 -
- 3,5 46 0,79 46 110’
10
Synthetic (3): lightly soiled resistant colours. 40° 800 -
- 3,5 46 0,56 46 100’
11
Coloured
40° 1400 -
- 7 53 0,89 70 100’
Eco & Rapid
12
Cotton Standard 20°C: lightly soiled whites and delicate colours. 20° 1400 -
- 7 - - - 170’
13
Eco Synthetic
20° 800 -
- 7 - - - 120’
14
Rapid
- 800 - -
- 1,5 - - - 9’
14
Rapid
30° 800 -
- 3 80 0,22 34 30
14
Rapid
60° 1000 -
- 7 - - - 60’
Partials
Rinse/Bleach - 1400 - -
7 - - - 50’
Spin + Drain - 1400 - - - - 7 - - - 10’
Drain only * - OFF - - - - 7 - - - 3’
Wash options
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with another
previously selected option, the indicator light will flash
accompanied by a buzzer (3 beeps), and only the latter
option will be activated; the indicator light corresponding
to the activated option will turn on.
Rapid
When this button is pressed the first time, the 9’ icon will
light up, when pressed the second time the 30’ icon lights
up and the third time the 1h icon lights up. When pressed
the fourth time the 9’ icon lights up again.
Fast Forward
During a wash programme and under certain conditions,
pressing this button allows for ending the wash
programme after only 20’ if necessary, by performing a
brief rinse cycle followed by a spin cycle at maximum 800
rpm or lower, if reduced manually during the programme
customisation phase.
In this case, washing and rinsing performance will be
reduced. After pressing the button, the relative indicator
light turns on together with the indicator light of the rinse
phase. If the selected temperature is equal to 40° and/
or the button is pressed during the initial phase of the
programme, the “Fast Forward” option lasts longer so that
the detergent can dissolve properly and avoid damaging
the fabrics. In this case, the rinse phase indicator light
flashes while the wash indicator light remains fixed until
the necessary activation conditions are fulfilled. If less than
20’ remain of the wash programme, the option will be
disabled.
Stain removal
Thisoptionallowsforselectingthetypeofdirtsoasto
optimally adjust the cycle for removing the stains. The
following types of dirt can be selected:
- Food, for stains caused by foodstuffs and beverages,
for example.
- Work, for grease and ink stains, for example.
- Outdoor, for mud and grass stains, for example.
! The wash cycle duration varies according to the type of
selected dirt.
* If you select programme and exclude the spin cycle, the machine will drain only.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
10
GB
Push & Wash
This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF
button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the
Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.
The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes
at a temperature of 30° and a maximum spin speed of 1200 rpm. Maximum load 3,5 kg. (Cycle duration 50’).
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and close the door.
2. Pour the detergent and additives.
3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns
green and the door will lock (the DOOR LOCKED symbol turns on).
N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle
recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.
To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol
is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at
which it was interrupted.
4. Once the programme is finished, the END indicator light turns on.
11
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
Compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
Compartment 2: Washing detergent (powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage. If powder detergent is used, place the partition
into slot B.
Compartment 3: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “max” level indicated
on the central pin.
Extra compartment 4: Bleach
Bleach cycle
Insert the additional compartment 4 (provided) into
compartment 1. In pouring the bleach do not exceed the
max” level indicated on the central pin.
Perform bleaching by pouring the bleach into additional
compartment 4 and set the programme .
! Traditional bleach should be used on resistant white
fabrics, and delicate bleach for coloured and synthetics
fabrics and for wool.
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Do not exceed thevalueslistedin the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1.200 g
1 towel 150-250 g
Special wash cycles
Sport (programme 1) is designed for washing lightly soiled
sports clothing (tracksuits, shorts, etc.); for best results, we
recommend not exceeding the maximum load indicated
in the “Table of wash cycles”. We recommend using liquid
detergent, and adding the amount suitable for a half-load.
Dark: use programme 2 to wash dark-coloured garments.
This programme is designed to maintain dark colours over
time. We recommend using a liquid detergent for the best
results when washing dark-coloured garments.
Anti-odour: use programme 3 for washing garments
with bad odours (e.g. smoke, sweat, fried food). The
programme is designed to remove bad odours while
preserving the fabric fibres. Synthetics fabrics or mixed
loads should be washed at 40°, and resistant cotton
fabrics at 60°.
Delicate: use programme 4 to wash very delicate
garments. It is advisable to turn the garments inside out
before washing them. For best results, use liquid detergent
on delicate garments.
Wool - Woolmark Apparel Care - Blue: the wool wash
cycle of this machine has been approved by The
Woolmark Company for the washing of wool garments
labelled as “hand wash” provided that the products are
washed according to the instructions on the garment label
and those issued by the manufacturer of this washing
machine. (M1126)
In UK, Eire, Hong Kong and India the Woolmark trade mark
is a Certification trade mark.
Duvet: to wash single duvets (the weight of which should
not exceed 2 kg), cushions or clothes padded with
goose down such as puffa jackets, use the special wash
programme number 6. We recommend that duvets are
placed in the drum with their edges folded inwards (see
figure) and that no more than ¾ of the total volume of the
drum is used. To achieve the best results, we recommend
that a liquid detergent is used and placed inside the
detergent dispenser drawer.
Coloured: use this programme 11 to wash bright
coloured clothes. The programme is designed to maintain
bright colours over time.
12
GB
Cotton Standard 20°C (programme 12) ideal for lightly
soiled cotton loads. The effective performance levels
achieved at cold temperatures, which are comparable to
washing at 40°, are guaranteed by a mechanical action
which operates at varying speed, with repeated and
frequent peaks.
Eco Synthetic (programme 13) ideal for mixed loads
(cotton and synthetics) with a normal soil level. The
effective performance levels achieved at cold temperatures
are guaranteed by a mechanical action which operates at
varying speed, across set average intervals.
Rapid (programme 14) allows for varying the garment
treatment duration from 9’ to 1h. Pressing the
corresponding “Rapid” button allows for varying the cycle
duration between 9’ (refresh), 30’ (wash), 1h (wash).
The 9’ cycle refreshes garments using fabric softener
only; it is advisable not to add any detergent into
the machine. The 30’ programme is designed to wash
lightly soiled garments at 30° (excluding wool and silk)
with a 3 kg maximum load in a short time: it only lasts 30
minutes and allows for saving time and energy. The “1h”
cycle is designed to wash moderately soiled resistant
cotton garments at 60° in an hour, with good washing
performance. For synthetic or mixed garments, we
recommend lowering the temperature down to 40°.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
13
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” on the
display).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
Theoption and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Push & Wash does not activate.
The programme lasts a lot less
that expected.
Possible causes / Solutions:
•Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.
•Thereisnopowerinthehouse.
•Thewashingmachinedoorisnotclosedproperly.
•TheON/OFFbuttonhasnotbeenpressed.
•TheSTART/PAUSEbuttonhasnotbeenpressed.
•Thewatertaphasnotbeenopened.
•Adelayedstarthasbeenset.
•Thewaterinlethoseisnotconnectedtothetap.
•Thehoseisbent.
•Thewatertaphasnotbeenopened.
•Thereisnowatersupplyinthehouse.
•Thepressureistoolow.
•TheSTART/PAUSEbuttonhasnotbeenpressed.
•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
•Thefreeendofthehoseisunderwater(see “Installation”).
•Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
•Thewashcycledoesnotincludedraining:somecyclesrequirethedraining
process to be enabled manually.
•Thedrainhoseisbent(see “Installation”).
•Thedrainageductisclogged.
•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
•Thewashingmachineisnotlevel(see “Installation”).
•Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
•Thedrainhoseisnotfixedproperly(see “Installation”).
•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for
washing machines” or “hand and machine wash”, or the like).
•Toomuchdetergentwasused.
• AfterswitchingonthemachineacontrolotherthanPush&Washwasactivated.
Switch the machine off and press the Push & Wash button.
• The“FastForward”optionwasactivated.
14
GB
Service
Before contacting the Technical Assistance Service:
• Checkwhetheryoucansolvetheproblemalone(see“Troubleshooting”).
• Restartthewashcycletocheckwhethertheproblemhasbeensolved.
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
FR
15
Français
FR
LAVE-LINGE
Sommaire
Installation, 16-17
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Entretien et soin, 18
Coupure de l’arrivée d’eau et du courant
Nettoyage du lave-linge
Nettoyage du tiroir à produits lessiviels
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau d’arrivée de l’eau
Précautions et conseils, 19
Sécurité générale
Mise au rebut
Ouverture manuelle de la porte hublot
Description du lave-linge, 20-21
Bandeau de commandes
Écran
Comment faire un cycle de lavage, 22
Programmes et options, 23-24
Tableau des programmes
Options de lavage
Push & Wash
Produits lessiviels et linge, 25-26
Tiroir à produits lessiviels
Cycle blanchissage
Triage du linge
Programmes spéciaux
Système d’équilibrage de la charge
Anomalies et remèdes, 27
Assistance, 28
XWE 71483
Mode d’emploi
16
FR
Installation
! Conserver ce mode d’emploi pour pouvoir
le consulter à tout moment. En cas de vente,
de cession ou de déménagement, veiller à
ce qu’il suive toujours le lave-linge pour que
son nouveau propriétaire soit informé sur son
mode de optionnement et puisse profiter des
conseils correspondants.
! Lire attentivement les instructions: elles
fournissent des conseils importants sur
l’installation, l’utilisation et la sécurité de
l’appareil.
Déballage et mise à niveau
Déballage
1. Déballer le lave-linge.
2. Contrôler que le lave-linge n’a pas été
endommagé pendant le transport. S’il est
abîmé, ne pas le raccorder et contacter le
vendeur.
3. Enlever les 4 vis
de protection servant
au transport, le
caoutchouc et la cale,
placés dans la partie
arrière (voir figure).
4. Boucher les trous à l’aide des bouchons
plastique fournis.
5. Conserver toutes ces pièces: il faudra les
remonter en cas de transport du lave-linge.
! Les pièces d’emballage ne sont pas des
jouets pour enfants.
Mise à niveau
1. Installer le lave-linge sur un sol plat et rigide,
sans l’appuyer contre des murs, des meubles
ou autre.
2. Si le sol n’est
pas parfaitement
horizontal, visser ou
dévisser les pieds de
réglage avant (voir
figure) pour niveler
l’appareil; son angle
d’inclinaison, mesuré
sur le plan de travail,
ne doit pas dépasser
2°.
Une bonne mise à niveau garantit la stabilité
de l’appareil et évite qu’il y ait des vibrations,
du bruit et des déplacements en cours de
optionnement. Si la machine est posée sur de
la moquette ou un tapis, régler les pieds de
manière à ce qu’il y ait suffisamment d’espace
pour assurer une bonne ventilation.
Raccordements eau et électricité
Raccordement du tuyau d’arrivée de
l’eau
1. Reliez le tuyau
d’alimentation en le
vissant à un robinet
d’eau froide à embout
fileté 3/4 gaz (voir
figure).
Faire couler l’eau
jusqu’à ce qu’elle
soit limpide et sans
impuretés avant de
raccorder.
2. Raccorder le tuyau
d’arrivée de l’eau
au lave-linge en le
vissant à la prise
d’eau prévue, dans la
partie arrière en haut
à droite (voir figure).
3. Attention à ce que le tuyau ne soit pas plié
ou écrasé.
! La pression de l’eau doit être comprise entre
les valeurs indiquées dans le tableau des
Caractéristiques techniques (voir page ci-
contre).
! Si la longueur du tuyau d’alimentation ne
suffit pas, s’adresser à un magasin spécialisé
ou à un technicien agréé.
! N’utiliser que des tuyaux neufs.
! Utiliser ceux qui sont fournis avec l’appareil.
FR
17
Raccordement du tuyau de vidange
Raccorder le tuyau
d’évacuation, sans
le plier, à un conduit
d’évacuation ou
à une évacuation
murale placés à
une distance du sol
comprise entre 65 et
100 cm ;
ou bien l’accrocher
à un évier ou à une
baignoire, dans ce
cas, fixer le support
en plastique fourni
avec l’appareil au
robinet (voir figure).
L’extrémité libre du
tuyau d’évacuation
ne doit pas être
plongée dans l’eau.
! L’utilisation d’un tuyau de rallonge est
absolument déconseillée mais si on ne peut
faire autrement, il faut absolument qu’il ait le
même diamètre que le tuyau original et sa
longueur ne doit pas dépasser 150 cm.
Raccordement électrique
Avant de brancher la fiche dans la prise de
courant, s’assurer que :
• lapriseestbienreliéeàlaterreetest
conforme aux réglementations en vigueur;
• lapriseestbienapteàsupporterla
puissance maximale de l’appareil indiquée
dans le tableau des Caractéristiques
techniques (voir ci-contre);
• latensiond’alimentationestbiencomprise
entre les valeurs figurant dans le tableau
des Caractéristiques techniques (voir ci-
contre);
• lapriseestbiencompatibleaveclafichedu
lave-linge. Autrement, remplacer la prise ou
la fiche.
! Le lave-linge ne doit pas être installé dehors,
même à l’abri, car il est très dangereux de le
laisser exposé à la pluie et aux orages.
! Après installation du lave-linge, la prise de
courant doit être facilement accessible.
65 - 100 cm
! N’utiliser ni rallonges ni prises multiples.
! Le câble ne doit être ni plié ni trop écrasé.
! Le câble d’alimentation ne doit être remplacé
que par des techniciens agréés.
Attention! Nous déclinons toute responsabilité
en cas de non-respect des normes
énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de l’appareil,
effectuer un cycle de lavage avec un produit
lessiviel mais sans linge et sélectionner
le programme «AUTO NETTOYANT» (voir
“Nettoyage du lave-linge”).
Caractéristiques techniques
Modèle
XWE 71483
Dimensions
largeur 59,5 cm
hauteur 85 cm
profondeur 54 cm
Capacité
de 1 à 7 kg
Raccorde-
ments élec-
triques
Voir la plaque signalétique
appliquée sur la machine
Raccor-
dements
hydrauli-
ques
pression maximale
1 MPa (10 bar)
pression minimale
0,05 MPa (0,5 bar)
capacité du tambour 52 litres
Vitesse
d’essorage
jusqu’à 1400 tours minute
Programmes
de contrôle
selon les
règlements
1061/2010
et
1015/2010
programme 8;
Coton standard 60°C.
programme 9;
Coton standard 40°C.
Cet appareil est conforme
aux Directives Communau-
taires suivantes:
- 2004/108/CE (Compatibili-
té électromagnétique)
- 2012/19/EU - WEEE
- 2006/95/CE (Basse Tension)
18
FR
Entretien et soin
Coupure de l’arrivée d’eau et du
courant
• Fermerlerobinetdel’eauaprèschaque
lavage. Cela réduit l’usure de l’installation
hydraulique du lave-linge et évite tout
danger de fuites.
• Débrancherlafichedelaprisedecourant
lors de tout nettoyage du lave-linge et
pendant tous les travaux d’entretien.
Nettoyage du lave-linge
• Pournettoyerl’extérieuretlespartiesen
caoutchouc, utiliser un chiffon imbi d’eau tiède
et de savon. N’utiliser ni solvants ni abrasifs.
Celave-lingeestéquipédunprogramme
«AUTO NETTOYANT» des parties internes qui doit
être effectué tambour complètement vide.
La lessive (dans une quantité égale à 10% de
celle conseillée pour du linge peu sale) ou les
additifs spéciaux pour le nettoyage du lave-
linge, pourront être utilisés comme adjuvants
dans le programme de lavage. Il est conseillé
d’effectuer le programme de nettoyage tous
les 40 cycles de lavage.
Pour activer le programme, appuyer
simultanément sur les touches A et B pendant
5 secondes (voir figure). Le programme
démarrera automatiquement et durera environ
70 minutes. Pour stopper le cycle, appuyer
sur la touche START/PAUSE.
Nettoyage du tiroir à produits
lessiviels
Pour sortir le tiroir,
appuyer sur le levier (1)
et tirer vers soi (2) (voir
figure).
Le laver à l’eau
courante ; effectuer
cette opération assez
souvent.
Entretien du hublot et du tambour
•Ilfauttoujourslaisserlehublotentrouvert
pour éviter la formation de mauvaise odeurs.
2
1
Nettoyage de la pompe
Le lave-linge est équipé d’une pompe
autonettoyante qui n’exige aucune opération
d’entretien. Il peut toutefois arriver que de
menus objets (pièces de monnaie, boutons)
tombent dans la préchambre qui protège la
pompe, placée en bas de cette dernière.
! S’assurer que le cycle de lavage est bien
terminé et débrancher la fiche.
Pour accéder à cette préchambre :
1. retirer le panneau
situé à l’avant
du lave-linge en
appuyant vers le
centre. Appuyer
ensuite vers le bas
de chaque côté et
l’extraire (voir figures).
2. dévisser le
couvercle en le
tournant dans le sens
inverse des aiguilles
d’une montre (voir
figure) : il est normal
qu’un peu d’eau
s’écoule;
3. nettoyer soigneusement l’intérieur;
4. revisser le couvercle;
5. remonter le panneau en veillant à bien enfiler
les crochets dans les fentes prévues avant de
le pousser contre l’appareil.
Contrôle du tuyau d’arrivée de
l’eau
Contrôler le tuyau d’alimentation au moins
une fois par an. Procéder à son remplacement
en cas de craquèlements et de fissures : car
les fortes pressions subies pendant le lavage
pourraient provoquer des cassures.
! N’utiliser que des tuyaux neufs.
1
2
3
A
B
FR
19
Précautions et conseils
! Ce lave-linge a été conçu et fabriqué conformément
aux normes internationales de sécurité. Ces consignes
sont fournies pour des raisons de sécurité, il faut les lire
attentivement.
Sécurité générale
•Cetappareilestconçupourunusagedomestique.
•Cetappareilpeutêtreutiliparlesenfantsà
partir de 8 ans et par les personnes dont les
capacis physiques, sensorielles ou mentales
sont réduites ou qui ne disposent pas des
connaissances suffisantes, à condition qu’ils
soient encads ou aient é fors de fon
appropriée pour l’utilisation de l’appareil de
façon re et en comprenant les dangers qui
y sont ls. Les enfants ne doivent pas jouer
avec l’appareil. Lentretien et le nettoyage ne
doivent pas être effectués par les enfants sans
surveillance.
•Nejamaistoucherl’appareilsil’onestpiedsnusetsiles
mains sont mouillées ou humides.
•Nejamaistirersurlecâblepourdébrancherlafichedela
prise de courant.
•Nepasouvrirletiroiràproduitslessivielssilamachine
est branchée.
•Nepastoucheràl’eaudevidange,ellepeutatteindre
des températures très élevées.
•Nepasforcerpourouvrirlehublot:leverrouillagede
sécurité qui protège contre les ouvertures accidentelles
pourrait s’endommager.
•Encasdepanne,éviteràtoutprixd’accéderaux
mécanismes internes pour tenter une réparation.
•Veilleràcequelesenfantsnes’approchentpasde
l’appareil pendant son optionnement.
•Pendantlelavage,lehublotatendanceàseréchauffer.
•Deuxoutroispersonnessontnécessairespourdéplacer
l’appareil avec toutes les précautions nécessaires. Ne
jamais le déplacer tout seul car il est très lourd.
•Avantd’introduirelelinge,s’assurerqueletambourest
bien vide.
Mise au rebut
•Miseaurebutdumatérield’emballage:seconformer
aux réglementations locales de manière à ce que les
emballages puissent être recyclés.
•LaDirectiveEuropéenne2012/19/EUsurlesDéchets
des Equipements Electriques et Electroniques, exige
que les appareils ménagers usagés ne soient pas
jetés dans le flux normal des déchets municipaux. Les
appareils usagés doivent être collectés séparément afin
d’optimiser le taux de récupération et le recyclage des
matériaux qui les composent et réduire l’impact sur la
santé humaine et l’environnement.
Le symbole de la ‘’poubelle barrée’’ est apposée sur
tous les produits pour rappeler les obligations de
collecte séparée. Les consommateurs devront contacter
les autorités locales ou leur revendeur concernant
la démarche à suivre pour l’enlèvement de leur vieil
appareil.
Ouverture manuelle du hublot
A défaut de pouvoir ouvrir la porte hublot à cause d’une
panne de courant pour étendre le linge, procéder comme
suit :
1. débrancher la fiche de la
prise de courant.
2. s’assurer que le niveau de
l’eau à l’intérieur de l’appareil
se trouve bien au-dessous
de l’ouverture du hublot, si
ce n’est pas le cas vider l’eau
en excès à travers le tuyau
de vidange dans un seau
comme illustré voir figure.
3. démonter le panneau
situé à l’avant du lave-linge
(voir figure).
4. se servir de la languette indiquée, tirer vers soi jusqu’à
ce que le tirant en plastique se dégage de son cran d’arrêt;
tirer ensuite vers le bas et ouvrir l’hublot en même temps.
5. remonter le panneau en veillant à bien enfiler les
crochets dans les fentes prévues avant de le pousser
contre l’appareil.
20
1
2
3
20
FR
Description du lave-linge
Bandeau de commandes
Touche
TEMPÉRATURE
BOUTON
PROGRAMMES
Tiroir à produits lessiviels
Touche ON/OFF
Touche
ESSORAGE
Touche et voyant
START/PAUSE
Touche
DÉPART
DIFFÉRÉ
Touches
OPTION
Tiroir à produits lessiviels : pour charger les produits
lessiviels et les additifs (voir “Produits lessiviels et linge”).
Touche ON/OFF : appuyer brièvement sur la touche
pour allumer ou éteindre l’appareil. Le voyant vert START/
PAUSE clignotant lentement indique que la machine est
allumée. Pour éteindre le lave-linge en cours de lavage,
appuyer sur la touche pendant au moins 3 secondes de
suite ; une pression brève ou accidentelle n’entraîne pas
l’arrêt de l’appareil.
L’arrêt de l’appareil pendant un lavage annule le lavage en
cours.
Touche PUSH & WASH: (voir “Programmes et options”).
BOUTON PROGRAMMES: pour sélectionner le
programme désiré (voir “Tableau des programmes”).
Touches OPTION: pour sélectionner les options
disponibles. Le voyant correspondant à l’option
sélectionnée restera allumé.
Touche TEMPÉRATURE : appuyer sur cette
touche pour diminuer la température ou pour l’exclure
complètement. La valeur correspondante s’affiche à
l’écran.
Touche ESSORAGE : appuyer sur cette touche
pour diminuer la vitesse de l’essorage ou pour l’exclure
complètement. La valeur correspondante s’affiche à
l’écran.
Touche DÉPART DIFFÉRÉ : appuyer pour
sélectionner un départ différé pour le programme choisi. Le
retard est affiché à l’écran.
Touche et voyant START/PAUSE : quand le voyant
vert clignote lentement, appuyer sur la touche pour
démarrer un lavage. Une fois le cycle lancé, le voyant
passe à l’allumage fixe. Pour activer une pause de lavage,
appuyer à nouveau sur la touche ; le voyant devient
couleur ambre et se met à clignoter. Si le symbole
n’est pas allumé, il est possible d’ouvrir le hublot. Pour
faire redémarrer le lavage exactement à l’endroit de l’arrêt,
appuyer une nouvelle fois sur la touche.
Stand-by
Ce lave-linge, conformément aux nouvelles normes en
vigueur dans le domaine de l’économie d’énergie, est
équipée d’un système d’extinction automatique (veille)
activé après environ 30 minutes d’inutilisation. Appuyez
brièvement sur la touche ON-OFF et attendre que la
machine soit réactivée.
ECRAN
Touche
PUSH & WASH
1 / 1

Indesit XWE 71483X W EU.1 Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi