Hotpoint AQC9 2F7 TM2 1 (EU) Mode d'emploi

Marque: Hotpoint

Modèle: AQC9 2F7 TM2 1 (EU)

Catégorie: Sèche-linge électriques

Taper: Mode d'emploi

TUMBLE DRYER

AQUALTIS

AQC9 2F7

Instruction booklet

This symbol reminds you to read this

instruction manual.

! Keep this instruction booklet on hand in order to refer to it when

necessary. Take it with you when you move, and, should you sell this

appliance or pass it on to another party, make sure that this booklet

is supplied along with the dryer so that the new owner may be infor-

med about warnings and suggestions on how the dryer works.

! Read these instructions carefully; the following pages contain impor-

tant information on installation and suggestions on how the appliance

works

English,1

www.hotpoint.co.uk

Contents

Installation, 2

Where to put your dryer

Ventilation

Electrical connection

Levelling the tumble dryer

Before you start using your dryer

Warnings, 4

General safety

Save energy and respect the environment

Care and maintenance, 6

Disconnecting the power supply

Cleaning the filter after each cycle

Checking the drum after each cycle

Empty the water container after each cycle

Cleaning the Heat Pump Filter

Cleaning the tumble dryer

Dryer Description, 8

To open door

The Features

Control Panel

The Display, 9

Start and Programmes, 10-15

Choosing a Programme

Special Programmes

Programmes Table

The Controls

Laundry, 16

Sorting your laundry

Care labels

Drying times

Troubleshooting, 17

Service, 18

Spare parts

Essential Contact Information

Disposal of old household appliances

Português,19

Français,37

Where to put your dryer

• Place your dryer at

a distance from gas

ranges, stoves, heaters,

or cooktops because

flames can damage the

appliance. The dryer

should be installed

in an ambient room

temperature of between

20 to 23°C for optimum

performance. But will function if the room is

between 14 and 30°C. If you are going to install the

appliance under a work counter, be sure to leave

a 10 mm space between the top and any other

objects on or above the machine and a 15 mm

space between the sides and lateral furnishings

or walls. This is to ensure proper air circulation.

The appliance must be installed with the rear

surface placed against a wall.

Ventilation

• When the dryer is in use, there has to be adequate ventilation.

Make sure you put your dryer in an environment that is not damp

and has proper air circulation throughout. Airflow around the dryer is

essential to condense the water produced during the washing, the

dryer will not operate efficiently in an enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation will be experienced.

We do not recommend that the dryer is

installed in a cupboard but the dryer must never

be installed behind a lockable door, a sliding

door or a door with a hinge on the opposite

side to that of the dryer door.

Less than 1m

Fig. A Fig. B

Water Drain

If the machine is positioned close to a drain it is possible to drain the

condensed water directly without using the waterbottle. In which

case it is no longer necessary to empty the water bottle at the end

of each cycle. If the Dryer is positioned above or close to a Washing

Machine the same drainage can be used. Just remove the tube

indicated in figure A and connect it to the drainage. If the drainage

is further away than the length of the tube it is possible to buy and

connect a tube of the same diameter and the necessary length in

order to reach the drain. To install the new tube just substitute the

existing one as indicated in figure B inserting it in the same place.

! The drain tube has to be below 1 m from the bottom of the Dryer.

! Once the Dryer has been installed please assure that the drain

tube is not bent or kinked.

Electrical connections

Before plugging the appliance into the socket,

check the following:

• Make sure your hands are dry.

• The socket must have an earth connection.

• The socket must be able to withstand the

machine’s maximum power output as indi-

cated on the rating plate (see Description

of the tumble dryer)

• The power supply voltage must fall within

the values indicated on the data plate (see

Description of the tumble dryer).

• The socket must be compatible with the

dryer’s plug. Should this not be the case,

replace the plug or the socket.

! DO NOT USE EXTENSION CORDS.

! The dryer must not be installed outdoors,

even if the space is sheltered. It can be very

dangerous if exposed to rain or storms.

! Once installed, the dryer’s electrical wire and

plug must be within reach.

! The power cord must not be bent or

squashed.

! If the plug being replaced is a non-

rewirable type, then the cut-off plug must

be disposed of safely. DO NOT leave it

where it can be inserted into a socket

and create a shock hazard.

! The power must be regularly checked. If the

supply cord is damaged, it must be repla-

ced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a

hazard. (see Assistance). New or longer elec-

tric cords are supplied by authorised dealers

at a supplementary cost.

! The manufacturer denies any

responsibility should any of these rules

not be followed.

! If in doubt about any of the above

consult a qualified electrician.

Levelling the tumble dryer

The dryer must be installed level for correct

operation.

When you have installed your dryer in its final

Installation

10 mm

15 mm

location check that it is level first side-to-side,

then front to back. If the dryer is not level,

adjust the two legs up or down until your

dryer is level.

Preliminary information

Once the tumble dryer is installed, clean the inside of the

drum before operating it and remove any dirt accumulated

during transportation.

Warning ! Before you use your dryer ensure that its has

been in a upright position for at least 6 hours.

Maximum load: 9 kg

This household tumble drier is a Condenser

The weighted Annual Energy Consumption (AEc)* kWh 1) 259.3

This household tumble drier is a Automatic

Energy consumption full load; Edry - kWh 2) 2.2

Energy consumption partial load; Edry½ - kWh 2) 1.16

Power consumption: off-mode (Po) - Watts 0.17

Power consumption: left-on mode (Pl) - Watts 3.73

Prog. Time - weighted (Tt) full & partial load - minutes 3) 186

Full load (Tdry) - minutes 251

Partial load (Tdry½) - minutes 137

weighted (Ct) full & partial load 3) 81

full load (Cdry) 82

partial load (Cdry½) 81

Airborne acoustical noise emissions - dB(A) re 1 pW 70.0

Programme time in minute, for program “Synthetics” full load

Partial load for program “Synthetics” N/A

Average condensation efficiency - %

1) The "standard cotton” at full and partial load are the standard programmes to

which the information in the label and the fiche relates. The standard cotton

program is suitable to dry at cupboard level (0%) cotton laundry and is the most

efficient programme in terms of energy consumption. Partial load is half the rated

load.

2) based on 160 drying cycles of the standard cotton programme at full and partial

load, and the consumption of the low-power modes. Actual energy consumption

will depend on how the appliance is used.

3) Weighted average of 3 cycles at full load and 4 cycles at half load.

Regulation 932/2012.

Energy consumption in kWh, for program “Synthetics” full load

0.61

Energy efficiency class on a scale from A+++ (low consumption)

to D (high consumption)

A++

Duration of the 'left-on mode' for power management system -

minutes

Condensation efficiency class on a scale from G (least efficient)

to A (most efficient)

Product Data - Regulation 392/2012.

Brand

Hotpoint/Ariston

Model

AQC9 2F7 TM2 1 (EU)

Rated capacity of cotton laundry for the "standard cotton

programme" at full load - kg

9.0

Warnings

! This appliance has been designed and built

according to international safety standards.

These warnings are given for safety reasons

and must be followed carefully.

General safety

• This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved.

• This tumble dryer has been designed for

home, and not professional, use.

• Do not touch the appliance while barefoot

or with wet hands or feet.

• Unplug the machine by pulling on the plug,

not the cord.

• After using the dryer, turn it off and unplug

it. Keep the door closed to make sure that

children do not use it as a toy.

• Children should be supervised to ensure

that they do not play with the dryer.

• Cleaning and user maintenance shall not be

made by children without supervision.

•Children of less than 3 years should be

kept away from the appliance unless

continuously supervised.

• The appliance must be installed correctly

and have proper ventilation. The air intake

at the front of the dryer should never be

obstructed (see Installation).

• Never use the dryer on carpeting where

the pile height would prevent air from

entering the dryer from the base.

• Check to see if the dryer is empty before

loading it.

•

The back of the dryer could become

very hot. Never touch it while in use.

•

Do not use the dryer unless the filter,

watercontainer and condenser are securely in

place (see Maintenance).

• Do not overload the dryer (see Laundry for

maximum loads).

• Do not load items that are dripping wet.

• Carefully check all instructions on clothing

labels (see Laundry).

• Do not tumble dry large, very bulky items.

• Do not tumble dry acrylic fibres at high

temperatures.

• Do not turn off the dryer when there are still

warm items inside.

• Clean the filter after each use (see

Maintenance).

• Empty the Water Container after each use

(see Maintenance).

• Clean the Heat Pump filter unit at regular

intervals (see Maintenance).

• Do not allow lint to collect around the dryer.

• Never climb on top of the dryer. It could

result in damage.

• Always follow electrical standards and

requirements (see Installation).

• Always buy original spare parts and

accessories (see Service).

To minimise the risk of fire in your tumble

dryer, the following should be observed:

• Tumble dry items only if they have been

washed with detergent and water, rinsed and

been through the spin cycle. It is a fire hazard

to dry items that HAVE NOT been washed

with water.

• Do not dry garments that have been treated

with chemical products.

• Do not tumble dry items that have been

spotted or soaked with vegetable or cooking

oils, this constitutes a fire hazard. Oil-affected

items can ignite spontaneously,especially

when exposed to heat sources such as

a tumble dryer. The items become warm,

causing an oxidisation reaction with the

oil, Oxidisation creates heat. If the heat

cannot escape, items can become hot

enough to catch fire. Piling, stacking or

storing oil-effected items can prevent heat

from escaping and so create a fire hazard.

If it is unavoidable that fabrics containing

vegetable or cooking oil or those that have

been contaminated withhair care products

be placed in a tumble dryer they should first

be washed with extra detergent - this will

reduce, but not eliminate the hazard. They

should not be removed from the dryer and

piled or stacked while hot.

• Do not tumble dry items that have previously

been cleaned in or washed in, soaked in

or soiled with petrol/gasoline, dry cleaning

solvents or other flammable or explosive

substances. Highly flammable substances

commonly used in domestic environments

including cooking oil, acetone, denatured

alcohol, kerosene, spot removers, turpentine,

waxes and wax removers. Ensure these

items have been washed in hot water with

an extra amount of detergent before being

dried in the tumble dryer.

• Do not tumble dry items containing foam

rubber (also known as latex foam), or

similarly textured rubber like materials.

Foam rubber materials can, when heated,

produce fire by spontaneous combustion.

• Fabric softener or similar products should

not be used in a tumble dryer to eliminate

the effects of static electricity unless the

practice is specifically recommended by

the manufacturer of the fabric softener

product.

• Do not tumble dry undergarments that

contain metal reinforcements eg. bras

with metal reinforcing wires. Damage to

the tumble dryer can result if the metal

reinforcements come loose during drying.

• Do not tumble dry rubber, plastic articles

such as shower caps or babies waterproof

covers, polythene or paper.

• Do not tumble dry rubber backed articles,

clothes fitted with foam rubber pads,

pillows, galoshes and rubber coated tennis

shoes.

• Remove all objects from pockets such as

lighters and matches.

! WARNING: Never stop the dryer before

the end of the drying cycle unless all

items are quickly removed and spread

out so that the heat is dissipated.

Save energy and respect the environment

• Wring out all items to eliminate excess water before

tumble drying (if you use a washing machine first, select

a high spin cycle). Doing this will save time and energy

during drying.

• Always dry full loads - you save energy: single items or

small loads take longer to dry.

• Clean the filter after each use to contain energy

consumption costs (see Maintenance).

Disconnecting the power supply

! Disconnect the dryer when not in use or

during cleaning and maintenance operations.

Cleaning the filter after each cycle

The filter is a fundamental component of the

dryer: its function is to collect lint and fluff that

form during drying.

Clean the filter once drying is completed, by

rinsing it under running water or cleaning it

with a vacuum cleaner. Should the filter beco-

me clogged, the flow of

air inside the dryer will

be seriously hampered:

drying times becomes

longer and more energy

is consumed. Moreover,

the dryer may become

damaged.

The filter is located in

front of the dryer seal

(see Picture).

Removing the filter:

1. Pull the filter’s plastic

handle upwards (see

Picture).

2. Clean the fluff off the

filter and replace it correctly. Ensure that the

filter is pushed fully home.

! Do not use the dryer unless the filter has

been replaced in its holder.

Checking the drum after each cycle

Rotate the drum manually to remove smaller items (handker-

chiefs) that could have been left inside the dryer.

Cleaning the drum

! Avoid using abrasives, steel wool or stainless steel cleaning

agents to clean the drum. A coloured film may appear on the

stainless steel drum surface: it may be caused by a combina-

tion of water and/or cleaning agents such as wash-softeners.

This coloured film does not affect the dryer’s performance.

Emptying the water container after each

cycle

Remove the water container and

empty it into a sink or other

suitable drain outlet, then

replace it correctly.

Always check the water

container and empty it before

starting a new drying cycle.

-Failure to empty the water container may cause the

following:

- The dryer stops heating (thus the load may still be

damp at the end of the drying cycle).

- The “Empty water container” LED activates to show

that the water container is full.

Priming the Water Collection System

When your dryer is new, the Water Container will not

collect Water until the system is primed, this will take

1 or 2 drying cycles. Once primed it will collect Water

during every cycle.

Cleaning the Heat Pump Filter Unit

• Periodically (every 5 drying cycles) remove

Heat pump filter unit and clean any build up

of fluff from the surface of the filter by rinsing

it under running water or with your vacuum

cleaner.

We however recommend that you clean this

filter after every drying cycle to optimise the

dryers performance.

To remove Heat pump

filter unit:

1. Unplug the dryer

and open the door.

2. Remove the filter

unit by rotating the

4 clips to the vertical

position then pulling

the filter unit towards you.

3. Separate the two

parts of the filter unit and

clean the surface of the

filter.

! Warning: The front of

the heat pump is made

from thin metal plates.

Take care that you do

not damage these or

cut yourself when cleaning, removing or

replacing the filter unit.

Care and maintenance

4.Whenever you clean the Heat pump filter

unit always clean any build up of fluff from

the surface of the metal plates.

Carefully clean this

fluff off with a damp

cloth,sponge or vacuum

cleaner. Never use your

Fingers.

5. Assemble the two

parts of the filter clean

the surface of the seals

and replace with the 4

clips into the horizontal

position, sure that the catches have been

secured.

Cleaning the tumble dryer

• The external metal, plastic and rubber parts can be clea-

ned with a damp cloth.

Water Contaniner

Heat Pump

Unit

Condenser Cover

Catches

Filter

Handle

Air Intake

• Clean the front air intake grille regularly (every 6 months)

with a vacuum cleaner to remove any lint, fluff or dust

deposits. Furthermore, remove any lint deposits from the

front part of the condenser and from the filter area, using

a vacuum cleaner every so often.

! Do not use solvents or abrasives.

! Have the dryer checked regularly by authorised technical

personnel in order to ensure that the electrical and mechani-

cal parts work safely (see Assistance).

Quick Tips

!Remember to clean your filter and Heat

Pump filter unit after each load.

! Remember to empty your water contain-

er after each load.

! Doing this will keep your machine work-

ing at its BEST!

To open door

Dryer Description

Control Panel

The On/Off button/light , if the dryer is running and this

button is pressed and held for more than 3 seconds the dryer

is turned off. The light signals that your dryer is in use or ready

to select a programme.

The Programmes knob sets the programme: rotate until the

indicator is pointing to the programme you want to select (see

Start and Programmes).

The Option buttons/ lights select available options for your

selected programme. The lights indicate that the option has

been selected (see Start and Programmes).

The Display Panel has three sections: Sensor Dry = Drying

level, Timed dry = Drying time and Time to End / Delay start

each with a corresponding selection button (see The Display).

START/PAUSE button with indicator light

: when the

green indicator light flashes slowly, press the button to

start the programme. When the cycle has started, the

indicator light is illuminated in a fixed manner. To pause

the programme, press the button again; the indicator light

will turn orange and begin to flash again. To restart the

programme from the point at which it was interrupted, press

the button again (see Start and Programmes).

The Programme Progress Lights indicate each state of the

programme by turning on as appropriate.(see Start and

Programmes).

Note: this light also ﬂ ashes amber during post care phase.

The Empty Water indicator

“h2o” signals that the water

container should be emptied. The light will take a few seconds

to go out after replacing the empty water container; the dryer

must be running for this to happen (see The Controls).

Note: if the water bottle is full the display shows

“h2o” and the

indicator flashes, the heat is turned off and your clothes will

not dry.

The Empty Water Clean Filter Light

gives a reminder

before every programme, that its essential to clean the filter and

empty the water container every time the dryer is used (see

Care and maintenance).

The Clean Heat Pump Filter Light

gives a reminder, that

its essential to clean this filter at regular intervals (see Care and

maintenance).

The Child Lock button/light

Press and hold this button after

selecting your programme and any options. This prevents the

programme settings from being changed.

When the light is lit the other buttons and programme knob are

disabled. Hold the button to cancel and the light will go out.

ECO Light - this light is illuminated as you select options that

use less energy (see the controls).

The Features

Pull on handle

Water

container

Rating

Plate

Filter

Air Intake

Grille

Model

& Serial

Numbers

Heat Pump Filter

Unit

(cover open)

Heat Pump Filter Unit cover

handle

(Pull here to open)

Clean Heat

Pump

Filter

Ajustable feet

(to level dryer)

Option Buttons and Lights

On/Off Button & Light

Display Panel

Child Lock

Button & Light

Start/Pause

Button & Light

Programme

Progress Light

Programme Knob

Empty

Water /

Clean Filter

Light

ECO

Light

Sensor Dry

Timed Dry

Delay

Timer

The Display

Timed Dry

After selecting a Programme that has a Timed Dry Option, press the Timed Button to select a drying time. The

display will reduce the selected time each time you press and release this button (see Start and Programmes).

Each press decreases the set time 220, 180, 150, 120, 90, 60, 40 and then repeats. If the Timed Dry option is

not available the display will flash and the buzzer beeps three times.The selected time remains displayed after the

programme starts and

can be changed during the programme if you wish.

! You can either choose a sensor dry level or a drying time.

Delay Start

After selecting a Programme that has a Delay Start Option a delay start time can be selected.

Each press of the Delay start button

advances the delay setting in 1 hour increments from “1h” to “24h” then

“OFF” and then after five seconds cancels the delay.

For delays of 10 hours or more the display counts down the time in hours until 10 hours, then the display shows

“9:59” and then counts down in minutes. For delays of 9 hours or less the display shows hours and minutes and

then counts down in minutes for all of the delay.

After the Start/Pause Button

is pressed the delay time can be changed or cancelled if you wish.

When the delay period finished the symbol is off and the Time to End is displayed.

If you have chosen a timed drying the display during programming will show the drying time only in the timed

drying display in the middle. After having pressed start the machine will turn the time display on and visualize

the countdown of the programme time.

Time to End

If the delay icon

is off the time displayed is the Time to End of the programme running.

When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.

When an Automatic programme is selected the time displayed is an estimate of the time remaining.

When the programme is selected the display shows the time required to dry a full load, The remaining time is

constantly monitored during the drying cycle and is updated to show the best forecast. The time to end is

displayed in hours and minutes and counts down each minute.

The colon between the hours and minutes display flashes to show that the time is counting down.

The Display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a

fault code number, the four option lights and the pause light will also flash Orange (see Troubleshooting).

The Display has three sections each with its corresponding button.

Sensor Dry

After selecting a programme that has a Sensor Dry Option, press and release the button until the required dryness

sensing level is displayed. If the sensing option is not available the display will flash and the buzzer beeps three

times.

! Some drying programmes are not compatible with all 7 sensor drying levels.

Dryness levels available

Damp dry: the most delicate level which makes sure that your clothes are not dripping wet. After a

hand-wash the perfect level to then hang your clothes if you do not want to tumble dry them all the way to

the end.

Iron Dry: a very delicate drying, It is useful for garments you would like to iron afterwards.

Hanger plus: just the drying status to hang delicate garments up (as curtains).

Hanger Dry: just the drying level to hang the garments up.

Light dry: ideal for delicate clothes to be folded and placed into the cupboard.

Cupboard Dry: the garments are completely dry and are ready to be folded and placed in the cupboard.

Ready to Wear: used for clothes to be worn straight away once the cycle is completed.

Start and Programmes

Choosing a Programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see Laundry).

3. Open the door and make sure the filter is clean and in place

and the water container is empty and in place (see Maintenance).

4. Load the machine and make sure that the items are not in

the way of the door seal. Close the door.

5. If the ON/Off light is not lit; press the On/Off Button

6. Select the Programmes selection that corresponds with

fabric being dried by checking the Programmes table (see

Programmes) as well as the indications for each type of

fabric (see Laundry).

7. Where available, choose Sensor Dry

or Timed Dry

option pressing and releasing the corresponding button until

the desired level or time is displayed.

! See programmes table, for more details.

8. Set a delay time and other options as necessary (see The Display).

9. If you wish the buzzer to sound at the end of the

programme, press the sound button

. If you have selected

the Crease Care option, this option is not available.

10. Press the START button

to begin. The display will

show the estimated time to end.

During the drying programme, you can check on your

laundry and take out the items that are dry while the others

continue drying. When you close the door again, press

Special Programmes

Easy Iron Programme

Easy Iron is a short 10 minute programme (8 minutes of heat followed by a 2 minutes cool tumble period) which fluffs the fibres of

clothing that has been left in the same position/location for an extended period of time. The cycle relaxes the fibres and makes them

easier to iron and fold.

! Easy Iron is not a drying programme and should not be used for wet articles of clothing.

For best results:

1. Do not load more than maximum capacity. These numbers refer to dry weight:

Fabric: Max

Cotton and Cotton mix 2.5 kg

Synthetics 2

Denim 2

2. Unload the dryer immediately after the end of the drying cycle, hang, fold or iron the articles and put them away in the closet.

Should this not be possible, repeat the cycle.

The Easy Iron effect varies from one fabric to the next. It works very well on traditional fabrics like Cotton or Cotton mix, and less

well on acrylic fibres and on materials such as Tencel.®

Wool Programme

• This is a programme for tumble dryer safe garments marked with the symbol .

• It can be used for load sizes up to 1 kg (approximately 3 sweaters).

• We recommend that garments are turned inside out before drying.

• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly

damp. Allow these to dry naturally as over-drying could damage garments.

! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.

! This program is not suitable for Acrylic garments.

Jeans

• This is a programme for Jeans made from Denim Cotton. Before drying your Jeans turn the front pockets inside out.

• It can be used for load sizes up to 3 kg (approximately 4 pairs).

• It can also be used on other garments made from same material such as jackets.

• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try turning

the jeans inside out and running the programme again for a short period.

• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in

your washer.

• Use this cycle only for a 100% cotton load, do not mix dark and light coloured items. Do not use this cycle for garments with

embroidery and accessories (pins,...), turn the pockets insideout

! We do not recommend that you use this programme if your jeans have elastic waist bands or embroidery.

START in order to resume drying.

If you open the door to check your laundry you will extend the

drying time as the heat pump compressor will not start until 5

minutes after you close the door and pressed the start Button

(see The Controls).

11. During the last few minutes of Drying Programmes before

the programme is completed, the final COOL TUMBLE phase

is entered (fabrics are cooled), this phase should always be

allowed to complete.

12. To let you know that your programme is complete the

buzzer will beep 3 times and the display shows END (Note:

if the SOUND option was selected the buzzer beeps 3 times

every 30 seconds for 5 minutes).Open the door, take your

laundry out, clean the filter and replace it. Empty the water

container and replace it (see Maintenance).

If the Crease Care

option has been selected and you do

not take the clothes out immediately the clothes will tumble

occasionally for 10 hours or until you open the door.

13. Switch dryer off using the On/Off button.

Standby mode

This tumble dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system which is

enabled after about 30 minutes if no activity is detected. Press

and hold the On-Off button until the dryer reactivates.

Special Programmes

Shirts

High Heat option

• This is a programme for Shirts made from Cotton.

• It can be used for load sizes up to 3 kg (approximately 10 shirts).

• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try

turning the shirts inside out and running the programme again for a short period.

• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used inyour

washer.

Low Heat option

• This is a programme for Shirts made from synthetic materials or a mixture of natural and synthetics materials such as

Polyester and Cotton.

• It can be used for load sizes up to 3 kg (approximately 14 shirts).

• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try

turning the shirts inside out and running the programme again for a short period.

Note: The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in

your washer.

Silk

• This is a programme for drying your Delicate Silk.

• It can be used for load sizes up to 0.5 kg.

• Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly damp. If this

is found try removing the load and open them out then run the programme again for a short period.

• Only for garments labelled suitable for tumble drying.

• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in

your washer.

Cuddly Toys

• With the cuddly toy cycle user can remove dust easier and wash the cuddly toys more often because the drying time is very

much reduced compared to drying in the open air. It’s a delicate drying cycle that dries at low temperature and with soft mechanical

action to maintain at best the original look and the shine of the hair.

Note: For allergy protection, just freeze for 24hrs your cuddly toys, wash and dry. Repeat every 6 weeks. Before drying remove

accessories such as clothes, collars, or sound boxes and protect plastic eyes (using masking tape).

The programme time will vary dependant on the exact make up of the load. The maximum load should not exceed 2.5 kg and no

individual item should be greater than 600 g.

Baby Delicate

• This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille) and for drying your

Delicate Clothes.

• Do not dry items such as bibs and nappy pants with plastic coverings.

• It can be used for load sizes up to 2 kg.

• Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly damp. If

this is found try turning them inside out and running the programme again for a short period.

• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in

your washer.

Refresh

Thanks to a cool air flow, oxygen penetrates the fibers and transports unpleasant odors such as cigarette smoke, frying, smog out

of the clothes. With this short program, you can easily refresh your garments in just 20 minutes.

! Airing is not a drying programme and should not be used for wet articles of clothing.

• If can be used on any load size up to 9 kg, but is more effective on smaller loads.

20-minute programme that airs your clothes with cool air. Use also to cool warm clothes.

Blended fabrics

This program permits to dry mixed loads consisting of colored cottons and synthetics only with the dry level Cupboard dry. When

reaching the dry level suitable for synthetics, an alarm signals that garments are ready for removal. The tumble dryer stops and the

Start/Pause light blinks. Remove synthetics, close the door and press the Start/Pause button. The tumble dryer goes on working

until remaining cotton garments reach the dry level Cupboard dry. The cycle can be used for loads up to 3 kg.

Anti Allergy

The programme has the ‘Seal of Approval’ endorsement from ‘Allergy UK’, which reflects the effective reduction and elimination of

allergens from the clothes. With this programme, thanks to the achievement of constant temperature for an extended period of time,

the effects of the most common allergens (including House Dust Mite) are neutralized.

Can be used on wet load to dry and treat or on a dry load just to treat your laundry.Maximum load is 9 kg for a wet load and 4 kg for

a dry load.

Bed & Bath

• This is a programme for Cotton Towels and sheets.

• It can be used for load sizes up to 9 kg.

• Loads dried using this programme are usually ready to use; the edges or seams may be slightly damp especially on large

items. If this is found try opening them out and running the programme again for a short period.

• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in

your washer.

Activewear

• This programme is specific for drying water-repellent fabrics and sports jackets (e.g. Gore-Tex, polyester, nylon). Drying the

garment after a wash cycle has a beneficial effect as it reactivates the garment’s water-repellent treatment.

It can be used for loads of up to 2 kg. Dryness level: only Cupboard Dry

• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in

your washer.

Heat & Enjoy

• The Heat & Enjoy cycle helps to heat towels & bathrobes for a warm sensation after a bath or a shower. It is also useful for

warming clothes before dressing during winter.

The cycle heats the clothes up to 37° (the body temperature) and keeps the same temperature for a maximum of 4 hours or until

the user stops the cycle by opening the door.

Load: 3 Kg.

!Note: during this programme a

icon rotates in the display until the temperature target is reached at which point the dryness

level icon flashes.

Colored Cycle

This program helps to preserve your colored garments by controlling motor speed, drum rotation as well as temperature, which is

lower.

• It can be used on cottons on each load up to maximum of 3 kg.

• The load must have been spun in washing machine with spin speed between 1200 – 1400 rpm.

• The duration of this program will depend on load size, selected dry level and spin speed during washing.

The wool drying cycle of

this machine has been

tested and approved by The

Woolmark Company. The

cycle is suitable to dry wool

garments which are labeled

“hand wash” provided that

the garments are washed

in a Woolmark endorsed hand washing cycle and dried

according to the instruction issued by the manufacturer.

M1219.

In UK, Eire, Hong Kong and India the Woolmark trade mark is

a Certification trade mark.

Programmes Table

! If the On/Off light is not lit; Press the On/Off Button and then select programme.

Programme What it does How to set it Notes / Options available

Easy Iron

Brief programme (approxima-

tely 10 minutes) that softens

fibres of clothing that is ready

for ironing.

1. Position the PROGRAMME knob on .

2. Select Alarm Option if required.

3. Press the Start Button .

! This is not a drying programme (see previous page).

Options available

Sound .

Refresh

20 min cool programme to air

your clothes

1. Position the PROGRAMME knob on

2. Select Alarm Option if required.

3. Press the Start Button .

Sound

Standard

Cotton**

Dries: your Cotton clothes.

N.B: Max. load 6 kg (with

Low Heat option)

1. Position the PROGRAMME knob on

2. Choose Sensor Dry

or Timed Dry

(see next page).

3. Select any Options if required.

4. Press the Start Button .

Sound

or Crease care . Delay Start . High Heat

Less Fluff .

Sensor Dry option, automatic drying:

Damp dry , Iron dry , Hanger Plus , Hanger dry

, Light dry , Cupboard dry , Ready to Wear *.

Shirts

Dries your shirt

1. Position the PROGRAMME knob on .

2. Choose Sensor Dry

or Timed Dry

(see next page).

3. Select any Options if required.

4. Press the Start Button .

Sound

or Crease care . Delay Start . High Heat

. Less Fluff .

Sensor Dry option, automatic drying:

Damp dry , Iron dry , Hanger Plus , Hanger dry

, Light dry , Cupboard dry .

Blended

fabrics

It dries blended synthetic and

cotton garments.

1. 1. Position the PROGRAMME knob on

2. Choose Sensor Dry

(see next page).

3. Select any Options if required.

4. Press the Start Button .

Sound or Crease care .

Anti Allergy

Anti Allergy treatment for your

cotton clothes.

1. Position the PROGRAMME knob on

2. Select any Options if required.

3. Press the Start Button .

Sound

or Crease care . Delay Start .

Synthetics

Dries: your synthetics clothes.

1. Position the PROGRAMME knob on

2. Choose Sensor Dry

or Timed Dry

(see next page).

3. Select any Options if required.

4. Press the Start Button .

Sound

or Crease care . Delay Start .

Sensor Dry option, automatic drying:

Damp dry , Iron dry , Hanger Plus , Hanger dry

, Light dry , Cupboard dry .

Bed & Bath

Dries your Towels and

bedding.

1. Position the PROGRAMME knob on

2. Choose Sensor Dry

(see next page).

3. Select any Options if required.

4. Press the Start Button .

Sound or Crease care . Delay Start . Less Fluff

Sensor Dry option, automatic drying:

Damp dry , Iron dry , Hanger Plus , Hanger dry

, Light dry , Cupboard dry , Ready to Wear *.

(We suggest to use only Cupboard dry)

Jeans

Dries denim clothes.

1. Position the PROGRAMME knob on .

2. Choose Sensor Dry

(see next page).

3. Select any Options if required.

4. Press the Start Button .

Sound

or Crease care . Delay Start .

Sensor Dry option, automatic drying:

Damp dry , Iron dry , Hanger Plus , Hanger dry

, Light dry , Cupboard dry , Ready to Wear *.

Wool

Dries: your Woollen clothes.

1. Position the PROGRAMME knob on .

2. Select any Options if required.

3. Press the Start Button .

Sound

Silk

Dries your silk items.

1. Position the PROGRAMME knob on

2. Choose Sensor Dry

(see next page).

3. Select any Options if required.

4. Press the Start Button .

Sound

Sensor Dry option, automatic drying:

Damp dry , Iron dry , Hanger Plus , Hanger dry

, Light dry , Cupboard dry .

(We suggest to use only Cupboard dry)

Baby

Delicate

Dries your baby clothes.

1. Position the PROGRAMME knob on .

2. Choose Sensor Dry

or Timed Dry (see

next page).

3. Select any Options if required.

4. Press the Start Button .

Sound

or Crease care . Delay Start .

Sensor Dry option, automatic drying:

Damp dry , Iron dry , Hanger Plus , Hanger dry

, Light dry , Cupboard dry .

(We suggest to use only Cupboard dry)

* just with High Heat option on ** This is the most ef cient program in terms of energy consumption (EU 392/2012). To reach

maximum ef ciency, select the CUPBOARD DRY level and the highest temperature option (Standard/Default starting con

guration)

Sensor Drying and Timed Drying

First select a programme (see programmes table).

! For the best performance do not open the door before the cycle has finished.

Programme What it does How to set it Notes / Options available

Cuddly Toys

Dries your cuddly toy.

1. Position the PROGRAMME knob on .

2. Select any Options if required.

3. Press the Start Button .

Sound

. Delay Start .

Colored Cycle

Dries colored clothes

1. Position the PROGRAMME knob on .

2. Select any Options if required.

3. Press the Start Button .

Sound . Delay Start .

Sensor Dry option, automatic drying:

Damp dry , Iron dry , Hanger Plus , Hanger

dry , Light dry , Cupboard dry .

(We suggest to use only Cupboard dry)

Activewear

Dries your sports clothes.

1. Position the PROGRAMME knob on

2. Select any Options if required.

3. Press the Start Button .

Sound or Crease care . Delay Start .

Heat & Enjoy

Heats your towel & bathrobe.

1. Position the PROGRAMME knob on

2. Press the Start Button .

Programme What it does How to set it Notes / Options available

Sensor

Drying

Always use Sensor Dry if pos-

sible for drying your clothes. It

will guarantee you best drying

results.

The heat setting depends

on the programme (material

option) selected.

1. Press and release the sensor Dry button until

the display shows the desired selection. Each

press advances , , , , , , and

then repeats.

! Some sensing programmes do not have all 7

dryness level options.

2. Select any Options if required.

3. Press the Start Button .

Options available

Sound

or Crease care . Delay Start .

High Heat

. Less Fluff .

Consult suggested drying times (see Laundry).

The last few minutes of these programmes is the cool

tumble phase.

Timed

Drying

(220, 180,

150, 120,

90, 60 or 40

minutes)

Always use timed drying

option if you want to decide

the drying time.

The heat setting depends

on the Programme (material

option) selected.

1. Press and release the Timed Button until the

display shows the required selection. Each

decreases time 220’, 180’, 150’, 120’, 90’,

60’, 40’ and then repeats.

• Baby Delicates have a maximum time of 180’.

2. Select any Options if required.

3. Press the Start Button .

Options available

Sound

or Crease care . Delay Start . High

Heat

Consult suggested drying times (see Laundry).

The last few minutes of these programmes is the cool

tumble phase.

The Controls

• Programme knob

! Warning, if after pressing the start button the programme

knob position is changed, the new position will NOT change

the programme selected.

To change programme press Start/Pause Button

to pause

the programme, the light flashes Amber, select new programme

and any option, the light will then flash green. Press the Start/

Pause Button

and the new programme will start.

• Option Buttons/ Lights

These buttons are used to customise the selected

programme to your requirements. Not all options are

available for all programmes (see Start and Programmes).

If an option is not available and you press the button, the

buzzer will beep three times. If the option is available the

option light next to the button lights to confirm the selection.

• ECO Light

This light is illuminated when you select programme options

that will use less energy than the default setting. Examples

are if you choose an Automatic or sensing programme or

use a timed dry setting less than the default time. This light

does not indicate that the optimum setting for energy use

has been selected; it only shows you that your selected

options will use less energy.

• Progress (

Drying, Cool tumble, ) Lights

The Progress lights show you the status of the programme. At

each stage of the programme the corresponding light turns on.

• Delay Start

The start of some programmes (see Start and Programmes)

can be delayed for up to 24 hours (see The Display).

Ensure the water bottle is emptied and the filter is cleaned

before setting a delayed start.

• Less Fluff

By reducing the mechanical action during the final drying

stage the amount of lint and fluff produced is substantially

reduced protecting the fibres of your garments. Note: For

Shirts programme, if you have selected Low Heat option,

this option is not available.

• Sound

A buzzer sounds at the end of the drying cycle to signal that

the programme has ended and the garments are ready to be

removed. Note: If you have selected the Crease Care option,

this option is not available.

• Crease Care

When a delayed start and this option have been selected the

clothes are tumbled occasionally during the delayed period

to help prevent creases developing.

After end of the drying and cool tumble cycles, the clothes

are occasionally tumbled to help prevent creases developing,

should you not be available to remove the load immediately

after the programme is complete. The

light is on during

this phase after end of the cycle and the start/pause light

flashes amber. flashes amber. Note: If you have selected the

Sound option, this option is not available.

• High Heat

When a drying time is selected, pressing this button sets

a high heat drying and the indicator light above the button

lights up.

• Empty Water Clean Filter Light

“h2o”

(If you have plumbed your dryer to a drain the light can be

ignored for the water bottle, as there is no need to empty the

water container). When

is on (not flashing) it reminds you to

empty the water container. If the water container fills during a

programme, the heater turns off and the dryer does a period

of Cool Tumble then the light flashes and the buzzer sounds.

You must empty the container and restart the dryer or the

clothes will not dry. After re-starting the dryer the light will take

a few seconds to go out. To avoid this always empty the water

container each time you use the dryer (see Maintenance).

! Please note that you ALWAYS have to clean the filter even if

you have plumbed your dryer to a drain.

• Door Opening

Opening the door (or pressing the Start/Pause Button) during a

programme will stop the dryer and have the following effects.

Note: The Start/Pause Light flashes Amber during the Post

Care phase of a programme.

• During a delay phase the delay will continue to count

down. The start button must be pressed to resume the

delay programme. One of the delay lights will flash to

show the current delay setting.

• The start button must be pressed to resume the

programme. The progress lights will change to show the

current status and the Start/Pause light will stop flashing

and turn green.

• During the post creasecare phase of a drying program,

the Programme will finish. Pressing the Start/Pause

button will restart a new program at the beginning.

• Changing the Programmes knob will select a new

programme and the Start/Pause Light will flash green.

You can use this to select the “Refresh” programme to

cool the clothes if you find them dry enough. Pressing the

start/pause button to begin new Programme.

• Heat Pump Protection System

The heat pump sytem has a compressor protection

feature, that operates if you open the door or there is a

power disruption or you turn off the dryer. This system

will prevent the heat pump compressor from starting for

5 minutes after the door is closed and the programme

started.

• Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, plug in the machine,

press and hold the ON/OFF button until the dryer

reactivates, then press Start/Pause button.

Cotton

High heat

1 Kg 2 Kg 3 Kg 4 Kg 5 Kg 6 Kg 7 Kg 8-9 Kg

Automatic

minutes

60-90 80-100 120-130 120-140 140-180 150-190 170-200 200-250

Timed

60 or 90 90 90-120 120-140 150

150 or

180

180-220 220

Drying times 800-1000 rpm in washing machine

Synthetics

Low heat

1 Kg 2 Kg 3 Kg 4 Kg

Automatic minutes

40-50 50-70 70-90 80-120

Timed Dry setting

40 or 60 40 or 60 60 or 90 90 or 120

Drying times on reduced spin in washing machine

Acrylics

(Delicates)

Low heat

1 Kg 2 Kg

Automatic minutes Timed dry only

Timed Dry setting

40 or 60 or 90 90 or 120 or 150

Drying times on reduced spin in washing machine

Drying times

Sorting laundry

• Check the symbols on the care labels of the various gar-

ments to verify whether the garments can be safely tumble

dried.

• Sort laundry according to the type of fabric.

• Empty all pockets and check for loose buttons.

• Close zips and hooks and fasten belts and strings without

tightening them.

• Wring out garments to remove the maximum amount of

water possible.

Do not load the dryer when garments are dripping wet.

Maximum load sizes

Do not overload the drum.

The following values indicate the weight of dry garments:

Natural fibres: maximum kg

Synthetic fibres: maximum kg

! Do not overload the dryer as this may result is reduced

drying performance.

Care labels

Always check the care labels, especially when placing

garments in the tumble dryer for the first time. Below are the

most commonly used symbols:

May be tumble dried.

Do not tumble dry.

Tumble dry – high heat.

Tumble dry – low heat.

Drying times

Drying times are approximate and may vary depending on

the following:

• Amount of water retained by items after the spin cycle:

towels and delicate items retain a lot of water.

• Fabrics: items of the same fabric, but with different texture

and thickness may have different drying times.

• Amount of laundry: single items and small loads may take

longer to dry.

• Drying: if items are to be ironed, they can be removed

from the dryer while still slightly damp. Items that require

complete drying can be left longer.

• Heat setting.

• Temperature of the room: the lower the temperature of the

room, the longer it will take for the dryer to dry clothing.

• Bulk: certain bulky items require special care during the

drying process. We suggest removing these items and

replacing them in the dryer once they have been shaken

out: repeat this procedure several times during the course

of the drying cycle.

! Do not over-dry items.

All fabrics contain natural dampness which helps to keep

them soft and fluffy.

The drying times provided refer to the automatic Cupboard

dry programmes.

The Timed drying settings are also indicated to enable you

to select the most suitable timed option.

The weight refers to dry items.

Laundry

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following troublesho-

oting suggestions.

Possible causes / Solutions:

• The plug is not plugged into the socket, or not making contact.

• There has been a power failure.

• The fuse has blown. Try to plug another appliance into the socket.

• You are using an extension cord. Try to plug the dryer’s power cord directly into the

socket.

• The door is not closed securely.

• The programme has not been set properly (see Start and Programmes).

• The START button has not been pressed (see Start and Programmes).

• You have set a delay time (see Start and Programmes).

• You have pressed the start button; there will be a short delay before the dryer starts.

Wait for drying to begin,do not press the start button again or the dryer will pause

and not begin drying.

• The filter has not been cleaned (see Maintenance).

• The water container needs emptying? The empty water

light is flashing and “h2o”

message is displayed?

(see Maintenance).

• The Heat Pump Filter needs cleaning (see Maintenance).

• The temperature setting is not ideal for the type of fabric you are drying (see Start and

Programmes, and Laundry).

• The correct drying time has not been selected for this load (see Laundry).

• The air intake grille is obstructed (see Installation and see Maintenance).

• The items are too wet (see Laundry).

• The dryer is overloaded (see Laundry).

• The water container was probably not emptied at the start of the programme. Do

not wait for the empty water signal always check and empty the container before

starting a new drying programme (see Maintenance).

• This is normal the empty water flashes when the container is full. If the light is on but not

flashing its just a reminder to empty the container (see Start and Programmes).

! For safety the dryer has a maximum programme time of 5 hours. If an automatic

programme has not sensed the required final moisture in this time the dryer will

complete the programme and stop. Check the above points and run the programme

again, if the results are still to damp, contact the service centre (see Service).

• If the display shows F followed by one or two numbers, Turn off and remove plug,

Clean the Filters (see Maintenance). Then replace plug turn on and start another

program.

If the number is displayed again Note down the number and contact the service

centre (see Service).

• The dryer is in ‘Demo’ mode. Press and hold both the On/Off and Start/Pause

buttons for 3 seconds. The display will show “dOn” for 3 seconds and then the

dryer will resume normal operation.

• The time to end is continuously monitored throughout the drying cycle and the time

is adjusted to give the best-estimated time. The displayed time may increase during

the cycle and this is normal.

• This is normal, particularly if the dryer has not been used for a while. If the noise

persists throughout the whole drying cycle then contact the service centre.

• The dryer has gone into standby mode to save power. This occurs if you have left the

dryer on or have had a power cut. It occurs after 30 minutes:

- if you leave the dryer without starting a programme;

- after your drying programme has finished.

Press and hold the ON/OFF button until the dryer reactivates

Problem:

The dryer won’t start.

Drying cycle will not begin.

It is taking a long time to dry.

The Empty water light is flashing but

the dryer has only been running for a

short period.

Empty water light is on and the water

container is not full.

Programme finishes and clothes dam-

per than expected.

The Display shows a fault code F follo-

wed by one or two numbers, the option

lights and pause light are flashing.

The display briefly shows “dOn”

every 6 seconds.

Time to End display changes during

drying.

The dryer makes a thumping noise du-

ring the first few minutes of operation.

The lights on the dryer control panel

are off although the dryer is switched

on.

Troubleshooting

Service

Heat Pump System

This dryer is fitted with a sealed heat pump system to dry

your clothes. To operate, the heat pump contains fluorinated

greenhouse gases ( F gases) which are covered by the Kyoto

Protocol. These F gases are contained in a hermetically

sealed unit. This sealed unit contains 0.29 kg of the F gas

R134a which acts as a refrigerant. GWP = 1430 (0.4 t C02).

If the sealed unit fails then it must be replaced by a new

sealed unit. Contact your nearest service centre for advise.

Note: The gases contained in the sealed unit are not

hazardous to health, but if they escape they will have an

impact on global warming.

Before calling the Service Centre:

• Use the troubleshooting guide to see if you can solve the

problem yourself (see Troubleshooting).

• If not, turn off the dryer and call the Service Centre

closest to you.

Spare Parts

This dryer is a complex machine. Repairing it yourself or having

a nonauthorised person try to repair it could cause harm to one

or more persons and to the machine, and could invalidate the

spare parts warranty.

Call an authorised technician if you experience problems while

using the machine.

Please note that it is an offence for an unqualified person to

undertaken any servicing or repair work that involves breaking

into the sealed heat pump unit.

This appliance has been designed, constructed and distributed in compliance with the

requirements of European Directives:

- LVD 2014/35/EU, EMC 2014/30/EU and RoHS 2011/65/EU.

Information on recycling and disposal

As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components

to reduce costs for our customers and to minimise materials wastage.

• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.

• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the

appliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.

Disposal of old household appliances

The European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household

electrical appliances must not be disposedof in the normal unsorted municipal waste stream. Old appliances must be

collected separately in order tooptimise the recovery and recycling of the materialsthey contain and reduce the impact on

human healthand the environment. This dryer has a sealed heat pump unit containing Fgases which should be recovered

and destroyed.The crossed out “wheeled bin” symbol on theproduct reminds you of your obligation,thatwhen you dispose of

the appliance it must beseparately collected.Consumers should contact their local authority orretailer for information concer-

ning the correct disposalof their old appliance.

Product Guarantee And Repair Information

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the

date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or

materials, we will, at our discretion, either repair or replace the appliance at no cost to you:

This guarantee is subject to the following conditions:

- The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions.

- The appliance is used only on the electricity or gas supply printed on the rating plate.

- The appliance has been used for normal domestic purposes only.

- The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any person not authorised by us.

- Any repair work must be undertaken by us or our appointed agent.

- Any parts removed during repair work or any appliance that is replaced become our property.

- The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

- Damage resulting from transportation, improper use, neglect or interference or as a result of improper installation.

- Replacement of any consumable item or accessory. These include but are not limited to: plugs, cables, batteries, light bulbs, fluorescent

tubes and starters, covers and filters.

- Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

Repairs and After Sales

For product help and advice, repairs, spare parts or accessories, we’re here to help.

For local repair engineers - 03448 111 606 ROI - 0818 313 413 UK standard local rate applies ROI local Irish rate applies

For Parts and Accessories visit: parts.hotpoint.co.uk/shop

Please remember to register your appliance at www.hotpointservice.co.uk to activate your 10 year parts guarantee.

Please note, our advisors will re

uire the followin

information: model number, serial number

Português

AQUALTIS

AQC9 2F7

Instruções para a

utilização

MÁQUINA DE SECAR ROUPA

Mantenha o presente manual num local

acessível para poder consultá-lo facilmente

sempre que necessário.

! Mantenha sempre o manual junto da máquina de secar roupa. Se

a máquina for vendida ou cedida a outras pessoas, faça-a acom-

panhar deste manual, para que os novos proprietários possam

conhecer as advertências e sugestões relacionadas com a utilização

da mesma.

! Leia com atenção estas instruções: as páginas seguintes contêm

informações importantes sobre a instalação e sugestões úteis sobre

o funcionamento do electrodoméstico.

www.hotpoint.eu

Índice

Instalação, 20

Onde instalar a máquina de secar roupa?

Ventilação

Ligação eléctrica

Nivelamento da máquina de secar roupa

Informações preliminares

Advertências, 22

Segurança geral

Economia energética e respeito pelo meio ambiente

Cuidados e manutenção, 24

Interrupção da alimentação eléctrica

Limpeza do filtro no fim de cada ciclo

Controlo do tambor no fim de cada ciclo

Esvaziamento do recipiente de recolha da água no fim de

cada ciclo

Limpeza da unidade Filtro da Bomba de Calor

Limpeza da máquina de secar roupa

Descrição da máquina de secar roupa, 26

Abertura da porta

Características

Painel de comandos

Visor, 27

Início e programas, 28-33

Selecção do programa

Programas especiais

Tabela dos programas

Comandos

Roupa, 34

Triagem da roupa

Etiquetas de manutenção

Tempos de secagem

Problemas e soluções, 35

Assistência, 36

Peças de reposição

Eliminação

Onde instalar a máquina de

secar roupa?

• As chamas podem

danificar a máquina

de secar roupa,

que deve pois ser

instalada num local

afastado de fogões

a gás, aquecedores,

radiadores ou placas

de cozinha. Para um

desempenho ideal,

a máquina deve ser

instalado à temperatura ambiente entre 20 e

23 °C. Mas irá funcionar a uma temperatura

entre 14 e 30 °C.

Se o electrodoméstico for instalado sob

uma banca, é necessário deixar um espaço

de 10 mm entre o painel superior do

electrodoméstico e outros objectos colocados

sobre o mesmo, e um espaço de 15 mm

entre os lados do electrodoméstico e as

paredes ou os móveis vizinhos. Deste modo,

fica garantida uma circulação do ar adequada.

O aparelho deve ser instalado com a superfície

traseira posicionada contra uma parede

Ventilação

• Quando a máquina de secar roupa estiver activa, deve

existir ventilação suficiente. Certifique-se de que instala a

máquina de secar roupa num local sem humidade e com

circulação do ar adequada. O fluxo de ar em torno da

máquina de secar é fundamental para permitir a condensação

da água produzida durante a lavagem. A máquina de secar

roupa não funciona correctamente se estiver instalada num

espaço fechado ou no interior de um móvel.

! Se a máquina de secar roupa for utilizada numa divisão

pequena ou fria, é possível que se forme uma pequena

quantidade de condensados.

! Não é aconselhável instalar a máquina

de secar roupa num armário. O

electrodoméstico não deve nunca ser

instalado por trás de uma porta de fechar à

chave, de uma porta de correr nem de uma

porta com dobradiças do lado oposto ao da

porta da máquina de secar roupa.

Descarga da água

Se a máquina for colocada junto de um tubo de descarga, é

possível fazer defluir a água condensada directamente sem

ter de utilizar o recipiente de recolha da água. Neste caso,

deixa de ser necessário esvaziar o recipiente de recolha da

água no fim de cada ciclo.

Se a máquina de secar roupa for instalada por cima ou

ao lado de uma máquina de lavar roupa, pode partilhar a

mesma conduta de descarga.

Basta desligar o tubo indicado na figura A e ligá-lo à

conduta de descarga.

Se a conduta de descarga estiver a uma distância superior

ao comprimento do tubo, para efectuar a ligação, é possível

adquirir e ligar um tubo de diâmetro idêntico e com o

comprimento necessário.

Para instalar o novo tubo, basta substituir o existente conforme

indicado na figura B inserindo-o na mesma posição.

! A conduta de descarga deve ficar 1 m mais baixa

relativamente ao fundo da máquina de secar roupa.

! Depois de ter instalado a máquina de secar roupa,

certifique-se de que o tubo de descarga não está

dobrado nem torcido.

H<1m

Fig. A Fig. B

Ligação eléctrica

Antes de introduzir a ficha na tomada

eléctrica, verifique o seguinte:

• Certifique-se de que tem as mãos secas.

• A tomada deve estar equipada com

ligação à terra.

• A tomada deve ter capacidade para

suportar a potência máxima prevista para a

máquina, indicada na placa dos dados de

exercício (consulte Descrição da máquina

de secar roupa).

• A tensão de alimentação deve estar

compreendida entre os valores indicados

na placa dos dados de exercício (consulte

Descrição da máquina de secar roupa).

• A tomada deve ser compatível com o tipo

de ficha da máquina de secar roupa. Caso

contrário, substitua a tomada ou a ficha.

! NÃO UTILIZE EXTENSÕES.

! A máquina de secar roupa não pode ser

instalada em ambientes externos, mesmo

que abrigados. Na verdade, pode ser muito

perigoso expor este electrodoméstico à

chuva ou a tempestades.

! Após a instalação da máquina de secar, o

cabo eléctrico e a ficha devem ser mantidos

ao alcance da mão.

Instalação

10 mm

15 mm

La page charge ...

Hotpoint AQC9 2F7 TM2 1 (EU) Mode d'emploi

Marque: Hotpoint

Modèle: AQC9 2F7 TM2 1 (EU)

Catégorie: Sèche-linge électriques

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Hotpoint AQC9 2F7 TM2 1 (EU) User guide
português: Hotpoint AQC9 2F7 TM2 1 (EU) Guia de usuario

Hotpoint AQC9 2F7 TM2 1 (EU) Mode d'emploi

Hotpoint AQC9 2F7 TM2 1 (EU) Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents