Whirlpool LKF 720 EX.R Mode d'emploi

Marque: Whirlpool

Modèle: LKF 720 EX.R

Catégorie: Lave-vaisselle

Taper: Mode d'emploi

Ce manuel convient également à

Operating instructions

Contents

Installation, 2-3-4

Positioning and levelling

Connecting the water and electricity supplies

Advice regarding the first wash cycle

Technical data

Electrical Connection

Description of the appliance, 5

Overall view

Control panel

Loading the racks, 6

Lower rack

Cutlery basket

Upper rack

Start-up and use, 7-8

Starting the dishwasher

Measuring out the detergent

Wash options

Wash cycles, 9

Table of wash cycles

Rinse aid and refined salt, 10

Measuring out the rinse aid

Measuring out the refined salt

Care and maintenance, 11

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended periods

Precautions, advice and Assistance, 12

General safety

Disposal

Saving energy and respecting the environment

Before contacting Assistance

Troubleshooting, 13

English,1

LKF 61

LKF 720

DISHWASHER

Français, 14

27

40 ،یسراف

Installation

Keep this instruction manual in a safe place for future

reference. If the appliance is sold, given away or moved,

please ensure the manual is kept with the machine, so that the

new owner may benefit from the advice contained within it.

Please read this instruction manual carefully: it contains

important information regarding the safe installation, use and

maintenance of the appliance.

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto

its back.

Positioning and levelling

1. Remove the appliance from all packaging and check that it

has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or back

panel are in contact with the adjacent cabinets or even with the

wall. This appliance can also be recessed under a single

worktop

* (see the Assembly instruction sheet).

3. Position the dishwasher on a level and sturdy floor. If the

floor is uneven, the front feet of the appliance may be adjusted

until it reaches a horizontal position. If the appliance is levelled

correctly, it will be more stable and much less likely to move or

cause vibrations and noise while it is operating.

*. Adjust the height of the rear foot from the front of the

appliance

* on the central lower part of the dishwasher, turning

a hexagonal spanner (red color) with an opening of 8 mm in a

clockwise direction to increase the height or in an

anticlockwise direction to decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies should

only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water supply

network using new hoses.

Do not use old hoses.

The water inlet (A) and outlet (B) hoses and the electricity

supply cable may be positioned towards the right or the left in

order to achieve the best possible installation (see figure).

Connecting the water inlet hose

 To a suitable cold water connection point: before attaching

the hose, run the water until it is perfectly clear so that any

impurities that may be present in the water do not clog the

appliance; after performing this operation, screw the inlet

hose tightly onto a tap with a ¾ gas threaded connection.

 To a suitable hot water connection point: your dishwasher

may be supplied with hot water from the mains supply (if

you have a central heating system with radiators) provided

that it does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to a

cold water supply.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician (see Assistance).

The water pressure must be within the values indicated in

the Technical data table (see adjacent information).

The hose should not be bent or compressed.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water

supply in the event of anomalies or leaks from inside the

appliance.

Some models are also equipped with the supplementary

safety device New Acqua Stop

*, which guarantees anti-

flooding protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be cut as it

contains live electrical parts.

* Only available in selected models.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain duct

with a minimum diameter of 4 cm. Alternatively, rest it over a

sink or tub; the free end of the hose should not remain

immersed in water.

The special plastic elbow

makes it easier to find the best

layout: fix the elbow to the wall

securely in order to prevent the

outlet hose from moving and

spilling the dirty water.

The part of the hose marked

with the letter A should be

between 40 and 100 cm above

the ground (see figure).

We advise against the use of hose extensions.

Electrical connection

Before inserting the plug into the electrical socket, make sure

that:

 The socket is earthed and complies with current

regulations.

 The socket can withstand the maximum load of the

appliance, which is indicated on the data plate located on

the inside of the door (see chapter entitled Description of

the appliance).

 The power supply voltage falls within the values indicated

on the data plate on the inside of the door.

 The socket is compatible with the plug of the appliance. If

this is not the case, ask an authorised technician to replace

the plug (see Assistance); do not use extension cables or

multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in order

to prevent all potential hazards. (See Assistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order to

protect it from any condensation which may form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before

running the first wash cycle, completely fill the salt dispenser

with water and add only then approximately 1 kg of salt (see

chapter entitled Rinse aid and refined salt). The water may

overflow: this is normal and is not a cause for concern. Select

the water hardness value (see chapter entitled Rinse aid and

refined salt).

- After the salt has been poured into the

machine, the LOW SALT indicator light

* switches off.

If the salt container is not filled, the water softener and the

heating element may be damaged as a result.

* Only available in selected models.

Technical data

Dimensions

width 60 cm

height 85 cm

depth 60 cm

Capacity 12 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

4.3 psi – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to

the following European

Community Directives:

-73/23/EEC dated 19/02/73

(Low Voltage) and subsequent

modifications

-89/336/EEC dated 03/05/89

(Electromagnetic Compatibility)

and subsequent modifications

-97/17/EC (Labelling)

-2002/96/ CE Waste Electrical

and Electronic Equipment

(WEEE)

Electrical Connection

If your appliance is supplied with a 13 amp. fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instruction below.

WARNING: THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacemente fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colours as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

Ifyour appliance has a non-rewireable moulded plug

and you should wish to remove it to re-route the

mains cable through partitions, units etc., please

esure that either:

- the plug is replaced by a fused 13 amp re-wireable

plug bearing the BSI mark of approval

- or:

- the mains cable is wired directly into a 13 amp

cable outlet, controlled by a switch, (in compliance

with BS 5733) which is accessible without moving

the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instruction for connecting cable to an altenative

plug:

Important: the wires in the mains lead are coloured

in accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

CAUTION:

- Once the appliance has been installed, the electrical

plug and socket should remain accessible.

- The Company shall not be held responsible for

any incidents that occur if these regulations are not

observed.

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminal in your plug, proceed as follows:

connect Green & Yellow wire to terminal market E

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a 13 amp fuse. A15 amp plug must be protected

by a 15 amp fuse, either in the plug or adaptor or at

the distribution board.

If you are in any doubt about the electrical supply to

your machine, consult a qualified electrician before

use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN AND YELLOW EARTH (E) or

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible

to the plug body and dispose of it as described

above.

GREEN &

YELLOW

BROWN

BLUE

13 amp fuse

CROSS-BAR

CORD GRIP

Electrical Connection

Overall view

Description of the

appliance

1. Upper rack

2. Upper sprayer arm

3. Tip-up compartments

4. Rack height adjuster

5. Lower rack

6. Lower sprayer arm

7. Cutlery basket

8. Washing filter

9. Salt dispenser

10. Detergent and rinse aid dispensers

11. Data plate

12. Control Panel

***

***Only in completely built-in models.

* Only available in selected models.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Control panel

ON/OFF/RESET

button

ON/OFF

indicator light*

Select wash

cycle knob

Half load

button and

indicator light*

Washing and 3h.

Delayed start

indicator light*

Drying and

6h.Delayed start

indicator light*

End and 9h.

Delayed start

indicator light*

Start/Pause button

and indicator light*

Multi-functional tablets

button and indicator light*

Delayed start

button and

indicator light*

Low Salt

indicator light*

Low Rinse aid

indicator light*

Loading the racks

Before loading the racks, remove all food residues from

the crockery and empty liquids from glasses and cups.

After loading the appliance, check that the sprayer arms

can rotate freely.

Lower rack

The lower rack can hold pans, lids, plates, salad bowls,

cutlery, etc. as seen in the Loading examples.

Plates and large covers should be placed at the sides of the

rack, ensuring that they do not block the rotation of the upper

sprayer arm.

Some dishwasher models are fitted with tip-up sections

which can be used in a vertical position when arranging

plates or in a horizontal position when arranging pans and

salad bowls.

Cutlery basket

The type of cutlery basket may vary according to the

dishwasher model: it may be modular, non-modular or a sliding

version. The non-modular basket must only be positioned at

the front of the lower rack.

The modular basket may be separated into two parts, a solution

which is recommended when performing a half load wash (only

in models offering this option), is available in a sliding version

(positioned at any point on the lower rack by sliding it between

the fixed or tip-up inserts.

- Both versions are fitted with a collapsible sliding system which

means the cutlery can be arranged in the best possible way.

Knives and other utensils with sharp edges must be

placed in the cutlery basket with the points facing

downwards, or they must be positioned horizontally in the tip-

up compartments on the upper rack.

Cutlery basket positioning examples

Upper rack

Load this rack with delicate and lightweight crockery:

glasses, tea and coffee cups, saucers, small salad bowls,

saucepans and small saucepans which are not too soiled,

using the Loading examples as a guide.

 Mugs and cups: place these on the tip-up compartments**.

 Long sharp knives and serving utensils: place these on the

tip-up compartments

**.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper

rack may be moved to a higher or lower level. (in models which

The height of the upper rack should ideally be adjusted

WHEN THE RACK IS EMPTY.

Never lift or lower the rack on one side only.

Open the left and right guide rail stops

and pull out the rack; position it higher or

lower as required, slide it along the guide

rails until the front wheels are in place

and close the stops (see figure).

If the rack is fitted with Dual Space

handles

* (see figure), pull out the upper

rack until it reaches its stop point, grip the

handles at the sides of the rack and move

it upwards or downwards, then slowly let it

fall back into place.

Loading examples for the upper rack

Loading examples for the lower rack

Items which should not be washed in the

dishwasher

 Wooden items, objects with wooden or horn handles or

glued-on parts.

 Items made from aluminium, copper, brass, pewter or tin.

 Items made from plastic material which is not heat-resistant.

 Antique or hand-painted porcelain.

 Antique silver. Silver which is not antique may, however, be

washed in the dishwasher using a delicate wash cycle,

provided that it does not come into contact with other metals.

We recommend the use of crockery which is dishwasher

safe.

*Only available in selected models.

** The number and position may vary.

Start-up and use

Measuring out the detergent

A good wash result also depends on the correct

amount of detergent being used; exceeding the stated

amount does not result in a more effective wash and

increases environmental pollution.

 Only use detergent which has been

specifically designed for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle

has ended.

The use of tablets is only recommended for

models which offer the MULTI-FUNCTIONAL

TABLETS option.

To achieve the best results from each washing and

drying cycle, powder detergent, rinse aid liquid and

salt should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing

button D.

2. Pour in the detergent after

consulting the Table of wash

cycles:

 For powder detergent use

compartments A and B.

 For detergent in tablet form:

when the cycle requires 1 tablet, place it in compartment

A and close the cover; when it requires 2, place the

second tablet at the bottom of the appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

* Only available in selected models.

Starting the dishwasher

1. Turn the water tap on.

2. Press the ON/OFF button: all the indicator lights on

the control panel will light up for a few seconds.

3. Open the door and pour in a suitable amount of

detergent (see below).

4. Load the racks (see Loading the racks) and shut the

door.

5. Select the wash cycle by turning the WASH CYCLE

SELECT knob in a clockwise direction: align the notch

on the knob with the number or symbol representing

the desired wash cycle. The START/PAUSE indicator

light will flash.

6. Select the wash options

* (see adjacent

information).

7. Start the cycle by pressing the START button; the

indicator light will light up and remain lit in a fixed

manner. The indicator light corresponding to the

wash phase will switch on, signalling that the wash

cycle has begun.

8. At the end of the wash cycle the END indicator light

will switch on (fixed light). Switch off the appliance by

pressing the ON/OFF button, shut off the water valve

and unplug the appliance from the electricity socket.

9. Wait for a few minutes before removing the

crockery, in order to avoid burns. Unload the racks,

beginning with the lower level.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that

it has only just begun: once the wash cycle has started,

switch off the machine by pressing and holding the ON/

OFF/Reset button. Switch it back on using the same

button and select the desired wash cycle and options.

Adding extra crockery

Press the Start/Pause button (the corresponding

indicator light will flash). Open the door, taking care to

avoid the escaping steam, and place the crockery inside

the appliance. Press the Start/Pause button (fixed light):

the cycle starts from the point at which it was interrupted.

If the Start/Pause button is pressed so as to pause the

machine, the wash cycle or the Delayed Start

* function

(if selected) is interrupted.

At this stage it is not possible to change the wash cycle.

Accidental interruptions

If the door is opened during the wash cycle, or if there is

a power cut, the cycle stops. It starts again from the point

at which it was interrupted once the door has been shut

or once the electricity supply is restored.

Wash options*

The OPTIONS may only be set, modified or reset

after the wash cycle has been selected and before

the Start/Pause button has been pressed.

Only the options which are compatible with the type of

wash cycle set may be selected. If an option is not com-

patible with the selected was cycle (see Table of wash

cycles), the corresponding LED flashes rapidly 3 times.

If an option is selected which is incompatible with an-

other option or wash cycle selected previously, the in-

compatible option light will flash 3 times and switches

off, while the most recently selected setting remains lit.

To deselect an option which has been set by mis-

take, press the corresponding button again.

Half load*

If there are not many dishes to be washed, a half load

cycle may be used in order to save water, electricity

and detergent. Select the wash cycle and press the

HALF LOAD button: the indicator light will illuminate.

Remember to halve the amount of detergent.

It is better to use powder detergent in this case.

This option is incompatible with the following

wash cycle: Speed wash.

Delayed start*

It is possible to delay the start time of the wash cycle by

3, 6 or 9 hours.

1: After selecting the desired wash cycle and any other

options, press the DELAYED START button. the indicator

light will illuminate.

2: Select the desired delay time by pressing the De-

layed Start button repeatedly; the wash phase (3 hours),

the drying phase (6 hours) and end (9 hours) indicator

lights will illuminate in succession.

If the Delayed Start button is pressed again, the option is

deselected and the indicator light switches off.

3. The countdown will begin once the Start/Pause but-

ton has been pressed. The selected delay period indi-

cator light flashes and the Start/Pause button stops flash-

ing (the light becomes fixed instead).

3. Once this time has elapsed, the DELAYED START

indicator light switches off and the wash cycle

begins.

The Delayed Start function cannot be set once a

wash cycle has been started.

Multi-functional tablets*

This option optimises washing and drying results.

When using multi-functional tablets, press the MULTI-

FUNCTIONAL TABLETS button. The corresponding

indicator light will illuminate. The Multi-functional

tablets option results in the lengthening of the wash

cycle.

The MULTI-FUNCTIONAL TABLETS option remains

set for subsequent wash cycles if it is not deselected.

The use of tablets is only recommended when the

MULTI-FUNCTIONAL TABLETS option is available.

This option is not recommended for use with wash

cycles which do not specify the use of multi-functional

tablets (see Table of options).

Table of options

* Only available in selected models.

A B C

Delayed

Start

Half

Load

Tabs

Intensive

Yes Yes Yes

Normal

Yes Yes Yes

Daily A 60

Yes Yes Yes

Soak

Yes Yes No

Eco

Yes Yes Yes

Speed 25’

Yes No Yes

Crystal

Yes Yes Yes

Wash cycles

If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the

dishwasher, reduce the amount of detergent used accordingly.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Notes:

Optimum performance levels when using the "Daily A 60 wash" and "Speed wash" cycles can be achieved by observing the

maximum amounts of crockery specified.

To make it easier to measure out the detergent, it is worth remembering that:

1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid

* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less

energy and is les harmful to the environment.

Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following

address: [email protected]

Detergent

(A) = compartment A

(B) = compartment B

Wash cycle selection

instructions

Wash cycle

Powder Liquid Tablets

Wash

cycles

which

include

drying

Options

Wash cycle

duration

(tolerance

±10%)

Hrs. Min.

Heavily soiled dishes and

pans (not to be used for

delicate items).

Intensive

30 g (A)

30 ml (A)

1 (A)

Yes

A-B-C

2:15’

Normally soiled pans and

dishes. Standard daily

wash cycle.

Normal

25 g (A)

5 g (B)

25 ml (A)

5 ml (B)

1 (A)

Yes

A-B-C

1:45’

Limited quantity of daily

soiling.

(4 place settings + 1

saucepan +1 frying pan).

Daily A 60

25 g (A)

25 ml (A)

1 (A)

A-B-C

1:00’

Pre-wash for dishes while

awaiting completion of the

load with the dishes from

the next meal.

Soak

A-B

0:08’

Environmentally-friendly

wash cycle with low energy

consumption levels,

suitable for pans and

dishes.

Eco

25 g (A)

5 g (B)

25 ml (A)

5 ml (B)

1 (A)

Yes

A-B-C

2:20’

Economic and fast wash to

be used for lightly soiled

dishes. (Run cycle

immediately after use) (2

plates + 2 glasses + 4

pieces of cutlery + 1

saucepan + 1 small frying

pan).

25 g (A)

25 ml (A)

1 (A)

A-C

0:25’

Economic and fast wash for

delicate items which are

sensitive to high

temperatures. (Run cycle

immediately after use) (12

glasses + delicate plates). Crystal

30 g (A)

30 ml (A)

1 (A)

Yes

A-B-C

1:30’

For available OPTIONS please refer to the Table of options on the Start-up and use page.

Rinse aid and refined salt

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to

add rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard. Follow the instructions given on the packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights

remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

 When the LOW RINSE AID* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning

the lid (G) in an anticlockwise

direction.

2. Pour in the rinse aid, making

sure it does not overflow from the

dispenser. If this happens, clean

the spill immediately with a dry

cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results,

you may adjust the quantity of rinse aid used. Use a

screwdriver to turn the dosage adjuster (F) to one of the 6

pre-set positions (the default position is set to 4):

 If there are streaks on the crockery, set the adjustment

device to a lower number (1-3).

 If drops of water remain on the crockery or if there are

limescale marks present after the cycle has finished, set

the adjuster to a higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of

appliance, supplies water without limescale which is then used

to wash the crockery.

This dishwasher offers a setting which helps to reduce

pollution and optimises washing performance in accordance

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

household with water.

- Switch the machine off using the ON/OFF button and open

the door.

- Set the SELECT WASH CYCLE knob first to wash cycle 5,

then to wash cycle 1, then to wash cycle 5 again.

- Press the ON/OFF button; the wash cycle phase indicator

lights will flash. It is now possible to select the water hardness

level. There is a water hardness level for every wash cycle:

E.g.: wash cycle 1, water hardness level 1

wash cycle 2, water hardness level 2, etc. etc., up to a maxi-

mum of 5

* levels.

(The default water softener setting is level 3).

- To exit the function, wait approximately 30 seconds or switch

off the machine using the ON/OFF button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f =

hardness measured in French degrees - mmol/l = millimoles

per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash

cycle, make sure that the dispenser is never empty.

Refined salt removes limescale from the water, thus

avoiding the formation of deposits on crockery.

The salt dispenser is located in the lower part of the

dishwasher (see Description) and should be filled:

 When the green float

* cannot be seen by simply looking at

the cap of the salt dispenser.

 When the LOW SALT

* indicator light on the control panel is

illuminated;

1. Remove the lower rack and

unscrew the container cap

(anticlockwise).

2. The first time you do this: fill the

water tank right up to its edge.

3. Position the funnel

* (see figure)

and fill the salt container right up to its

edge (this should hold approximately

1 kg); it is not unusual for a little water to leak out.

4. Remove the funnel* and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it

on, the head facing downwards so as to let the water flow out

of the four cracks which are arranged in a star shape on the

lower part of the cap. (Salt cap with green float

It is advisable to perform this procedure every time you

add salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

When necessary, measure out the salt before a wash

cycle so that any saline solution which has leaked out of the

salt dispenser is removed.

* Only available in selected models.

Water Hardness Table

°dH °fH mmol/l level

0 6 0 10 0 1 1

6 11 11 20 1.1 2 2

12 17 21 30 2.1 3 3

17 34 31 60 3.1 6 4

34 50 61 90 6.1 9

For values between 0°f and 10°f, we do not

recommend the use of salt.

* this setting may cause a slight increase in the

duration of the cycle.

Care and maintenance

Shutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle to avoid

leaks.

 Always unplug the appliance when cleaning it and

when performing maintenance work.

Cleaning the dishwasher

 The external surfaces of the machine and the control

panel may be cleaned using a non-abrasive cloth

which has been dampened with water. Do not use

solvents or abrasive products.

 Any marks on the inside of the appliance may be

removed using a cloth dampened with water and a

little vinegar.

Preventing unpleasant odours

 Always keep the door of the appliance ajar in order to

avoid moisture from forming and being trapped inside

the machine.

 Clean the seals around the door and detergent

dispensers regularly using a damp sponge. This will

avoid food becoming trapped in the seals, which is

the main cause behind the formation of unpleasant

odours.

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer

arms and block the holes used to spray the water. It is

therefore recommended that the arms are checked from

time to time and cleaned with a small non-metallic

brush.

The two sprayer arms may both be removed.

To remove the upper sprayer

arm, rotate the locking ring in

an anti-clockwise direction.

The upper sprayer arm should

be replaced with the holes

facing upwards.

The lower sprayer arm can be

removed by pressing on the

side tabs and pulling it

upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an

extended period of time, let the water run to make sure it

is clear and free of impurities before performing the

necessary connections. If this precaution is not taken,

the water inlet could become blocked and damage the

dishwasher.

Clean the water inlet filter at the tap outlet regularly.

- Turn off the water tap.

- Unscrew the end of the water inlet hose, remove the filter and

clean it carefully under running water.

- Replace the filter and screw the water hose back into

position.

Cleaning the filters

The filter assembly consists of three filters which remove food

residues from the washing water and then recirculate the

water. They should be cleaned if you wish to achieve the best

results in every wash.

Clean the filters regularly.

The dishwasher should not be used without filters, or if the

filter is loose.

After cleaning the filters, replace the filter assembly and fix it in

position correctly; this is essential for maintaining the efficient

operation of the dishwasher.

Leaving the machine unused for extended

periods

 Disconnect the appliance from the electricity supply and

shut off the water tap.

 Leave the door of the appliance ajar.

 When you return, run a wash cycle when the dishwasher is

empty.

 After several washes, check the filter assembly and if

necessary clean it thoroughly under running water, using a

non-metallic brush and following the instructions below:

1. Turn the cylindrical filter C in an anti-clockwise direction

and pull it out (fig. 1).

2. Remove the cup filter B by exerting a slight pressure on the

side flaps (fig. 2).

3. Slide out the stainless steel plate filter A (fig. 3).

4. Inspect the trap and remove any food residue. NEVER

REMOVE the wash cycle pump (black detail) (fig. 4).

* Only available in selected models.

Precautions, advice

and Assistance

This appliance was designed and manufactured in

compliance with current international safety standards. The

following information has been provided for safety reasons

and should therefore be read carefully.

General safety

 The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

 The appliance must be used by adults only, to wash

domestic crockery in accordance with the instructions in

this manual.

 The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

machine exposed to rain and storms.

 Do not touch the appliance when barefoot.

 When unplugging the appliance always pull the plug from

the mains socket, do not pull on the cable.

 The water supply tap must be shut off and the plug should

be removed from the electrical socket before cleaning the

appliance or carrying out any maintenance work.

 If the appliance breaks down, do not under any

circumstances touch the internal parts in an attempt to

perform the repair work yourself.

 Never touch the heating element.

 Do not lean or sit on the open door of the appliance: this

may cause the appliance to overturn.

 The door should not be left open as it may create a

dangerous obstacle.

 Keep detergent and rinse aid out of reach of children.

 The packaging material should not be used as a toy.

Disposal

 Disposal of packaging materials: observe local legislation

so that the packaging may be reused.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using the

normal solid urban waste cycle. Exhausted appliances

should be collected separately in order to optimise the cost

of re-using and recycling the materials inside the machine,

while preventing potential damage to the atmosphere and

to public health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations regarding

separated waste collection.

For further information relating to the correct disposal of

household appliances, owners may contact the relevant

public authority or the local appliance dealer.

Saving energy and respecting the

environment

Saving water and energy

 Only begin a wash cycle when the dishwasher is full. While

waiting for the dishwasher to be filled, prevent unpleasant

odours using the Soak cycle (see Wash cycles).

 Select a wash cycle which is suited to the type of crockery

and to the soil level of the crockery using the Table of wash

cycles:

- For dishes with a normal soil level, use the Eco wash

cycle, which guarantees low energy and water

consumption levels.

- If the load is smaller than usual activate the Half load

option

* (see Start-up and use).

 If your electricity supply contract gives details of electricity

saving time bands, run wash cycles during the periods

when a lower tariff is applied. The Delayed start

* button

(see Start-up and use) helps you organise the wash cycles

accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

 We strongly recommend that you use detergents that do

not contain phosphates or chlorine, as these products are

harmful to the environment.

 Enzymes provide a particularly effective action at

temperatures around 50°C, and as a result detergents

containing enzymes can be used in conjunction with low-

temperature wash cycles in order to achieve the same

results as a normal 65°C wash cycle.

 To avoid wasting detergent, use the product in appropriate

quantities based on the manufacturers recommendations,

the hardness of the water and the soil level and quantity of

crockery to be washed. Even if they are biodegradable,

detergents contain substances which may alter the balance

of nature.

* Only available in selected models.

Assistance

Before contacting Assistance:

 Check whether the problem can be resolved using

the Troubleshooting guide (see Troubleshooting).

 Restart the programme to check whether the problem

has ceased to exist.

 If the problem persists, contact the Authorised

Technical Assistance Service.

Never use the services of unauthorised technicians.

Please have the following information to hand:

 The type of malfunction.

 The appliance model (Mod.).

 The serial number (S/N).

This information can be found on the appliance data

plate (see Description of the appliance).

Troubleshooting

Whenever the appliance fails to work, check for a solution from the following list before calling for

Assistance.

Problem: Possible causes / Solutions:

The dishwasher does not start.

• The plug has not been inserted into the electrical socket properly,

or there is no power in the house.

• The dishwasher door has not been shut properly.

• A delayed start has been programmed (see Start-up and use).

No water drains out from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes

excessive noise.

• The dishes are rattling against each other or against the sprayer

arms.

• An excessive amount of foam has been produced: the detergent has

not been measured out correctly or it is not suitable for use in

dishwashers (see Start-up and use).

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of the refined salt is low or the dosage setting is not

suited to the hardness of the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

• The crockery is made from non-stick material.

The dishes and glasses are

streaked or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been

dried properly.

• A wash cycle without a drying programme has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse

aid and salt).

• The rinse aid dispenser setting is not high enough.

The dishes are not clean.

• The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has

not been measured out correctly or it is not suitable for use in

dishwashers (see Start-up and use).

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance).

• The refined salt level is low (see Rinse aid and salt).

The dishwasher does not take

any water in/Tap shut-off alarm

(the Salt, Rinse Aid, Drying and

End indicator lights flash).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance is locked because no action was taken when the

Salt and Rinse Aid indicator lights were flashing. Switch off the

machine using the ON/OFF button, turn on the tap and switch the

machine back on after 20 seconds by pressing the same button. Re-

programme the machine and restart the wash cycle.

Water loading solenoid valve

malfunction alarm

(the Salt, Rinse Aid and Drying

indicator lights flashes).

• Switch off the appliance by pressing the ON/OFF button and switch

it back on after a minute. If the alarm continues, shut off the water

tap to eliminate the risk of flooding, remove the plug from the

electrical socket and contact Assistance.

Water inlet hose alarm/Water

inlet filter blocked.

(the Salt,

Rinse Aid, Washing, Drying and

End indicator lights flashes).

• Switch off the appliance by pressing the ON/OFF button. Shut off

the water tap to eliminate the risk of flooding and remove the plug

from the electrical socket.

Make sure the water inlet filter has not become blocked by various

impurities. (see “ Care and maintenance” chapter).

Mode demploi

Sommaire

Installation, 15-16-17

Mise en place et mise à niveau

Raccordements eau et électricité

Conseils pour le premier lavage

Caractéristiques techniques

Raccordement électrique

Description de lappareil, 18

Vue densemble

Tableau de bord

Charger les paniers, 19

Panier inférieur

Panier à couverts

Panier supérieur

Mise en marche et utilisation, 20-21

Mettre en marche le lave-vaisselle

Charger le produit de lavage

Options de lavage

Programmes, 22

Tableau des programmes

Produit de rinçage et sel régénérant, 23

Charger le produit de rinçage

Charger le sel régénérant

Entretien et soin, 24

Coupure de larrivée deau et de courant

Nettoyer le lave-vaisselle

Eviter les mauvaises odeurs

Nettoyer les bras de lavage

Nettoyage du filtre dentrée deau

Nettoyer les filtres

En cas dabsence pendant de longues périodes

Précautions conseils et Service, 25

Sécurité générale

Mise au rebut

Economies et respect de lenvironnement

Service

Anomalies et remèdes, 26

Français, 14

LKF 61

LKF 720

LAVE-VAISSELLE

Installation

Conserver ce mode demploi pour pouvoir le consulter à

tout moment. En cas de vente, de cession ou de

déménagement, sassurer quil accompagne bien lappareil.

Lire attentivement les instructions : elles contiennent des

conseils importants sur linstallation, lutilisation

et la sécurité de lappareil.

En cas de déménagement, transporter lappareil

verticalement; si besoin est, lincliner sur le dos.

Mise en place et mise à niveau

1. Déballer lappareil et sassurer quil na pas été endommagé

pendant le transport.

Sil est abîmé, ne pas le raccorder et contacter le revendeur.

2. Installer le lave-vaisselle de manière à ce que les côtés et la

paroi arrière touchent aux meubles adjacents ou au mur.

Lappareil peut être encastré sous un plan de travail continu

(voir feuille de Montage).

3. Installer le lave-vaisselle sur un sol plat et rigide.

Compenser les irrégularités en vissant ou en dévissant les

pieds avant jusquà ce que lhorizontalité de lappareil soit

parfaite. Une bonne horizontalité garantit la stabilité de

lappareil et supprime tout risque de vibrations, bruits et

déplacements.

*. Pour régler la hauteur du pied arrière, agir sur la douille

rouge à six pans située dans la partie avant du lave-vaisselle,

en bas et au milieu, à laide dune clé mâle à six pans,

ouverture 8 mm. Tourner dans le sens des aiguilles dune

montre pour augmenter la hauteur et dans le sens inverse

pour la diminuer. (consulter la notice dinstructions encastré

jointe à la documentation)

Raccordements eau et électricité

Ladaptation des installations électriques et les travaux de

plomberie de linstallation doivent être effectués par du

personnel qualifié.

Le lave-vaisselle ne doit pas écraser les tuyaux ou le

câble dalimentation électrique.

Utiliser des tuyaux neufs pour effectuer le raccordement

de lappareil au réseau de distribution de leau.

Ne pas réutiliser les anciens tuyaux.

Les tuyaux damenée (A) et dévacuation (B) de leau et le

câble dalimentation électrique peuvent être orientés vers la

droite ou vers la gauche pour simplifier linstallation (voir

figure).

Raccord du tuyau damenée de leau

 A une prise deau froide: bien visser le tuyau damenée à

un robinet à embout fileté 3/4 gaz; avant de visser, faire

couler leau jusquà ce quelle devienne limpide et

dépourvue dimpuretés qui pourraient engorger lappareil.

 A une prise deau chaude: en cas dinstallation de

chauffage centralisé (radiateurs), le lave-vaisselle peut être

alimenté avec de leau chaude de réseau ne dépassant

pas 60°C.

Visser le tuyau au robinet en procédant comme pour la

prise deau froide.

Si la longueur du tuyau damenée ne suffit pas, sadresser

à un magasin spécialisé ou à un technicien agréé (voir

Assistance).

La pression de leau doit être comprise entre les valeurs

reportées dans le tableau des Caractéristiques techniques (voir

ci-contre).

Faire attention à ce que le tuyau ne soit ni plié ni écrasé.

Sécurité anti-fuite

Pour éviter tout risque dinondation, le lave-vaisselle :

- est équipé dun dispositif qui coupe larrivée de leau en cas

danomalie ou de fuite à lintérieur de lappareil.

Quelques modèles sont équipés dun dispositif de sécurité

supplémentaire New Acqua Stop

* qui garantit contre tout

risque dinondation même en cas de rupture du tuyau

damenée de leau.

ATTENTION : TENSION DANGEREUSE!

Il ne faut en aucun cas couper le tuyau damenée de leau car il

contient des parties sous tension.

* Présent uniquement sur certains modèles.

Raccord du tuyau dévacuation de leau

Raccorder le tuyau dévacuation, sans le plier, à une conduite

dévacuation ayant au moins 4 cm de diamètre. Ou bien

laccrocher au bord dun évier; lextrémité libre du tuyau de

vidange ne doit pas être plongée dans leau.

Un coude

* plastique spécial

facilite une installation optimale

: fixer solidement le coude au

mur pour éviter que le tuyau se

déplace et déverse leau hors

du conduit.

La portion de tuyau repérée

par la lettre A doit se trouver à

une distance du sol comprise

entre 40 et 100 cm (voir

figure).

Lutilisation de tuyaux de rallonge est déconseillée.

Raccordement électrique

Avant de brancher la fiche dans la prise de courant, sassurer

que :

 la prise dispose de mise à la terre et est conforme aux

normes;

 la prise est bien apte à supporter la puissance maximale

de lappareil reportée sur la plaque signalétique fixée à la

contre-porte (voir paragraphe Description du lave-

vaisselle);

 la tension dalimentation est bien comprise entre les valeurs

figurant sur la plaque signalétique de la contre-porte;

 la prise est bien compatible avec la fiche de lappareil.

Autrement, faire remplacer la fiche par un technicien agréé

(voir Assistance); nutiliser ni rallonges ni prises multiples.

Après installation de lappareil, le câble dalimentation

électrique et la prise de courant doivent être facilement

accessibles.

Le câble ne doit être ni plié ni trop écrasé.

Afin déviter tout danger, faire changer le cordon dalimen-

tation abîmé, par le fabricant ou par son service après-vente.

(Voir Assistance)

Nous déclinons toute responsabilité en cas de non-

respect des normes énumérées ci-dessus.

Ruban anti-condensation*

Après avoir encastré le lave-vaisselle, ouvrir la porte et coller

le ruban adhésif transparent sous le plan en bois pour le

protéger contre la formation de condensation.

Conseils pour le premier lavage

Une fois linstallation terminée et tout de suite avant le premier

lavage, remplir complètement deau le réservoir à sel et ajouter

environ 1 kg de sel (voir Produit de rinçage et sel régénérant)

: il est tout à fait normal que de leau déborde. Sélectionner le

degré de dureté de leau (voir Produit de rinçage et sel

régénérant). - Après remplissage du réservoir à sel, le voyant

SEL

* s'éteint.

Le manque de remplissage du réservoir à sel, peut

endommager l'adoucisseur d'eau et l'élément chauffant.

* Présent uniquement sur certains modèles.

Caractéristiques techniques

Dimensions

largeur 60 cm

hauteur 85 cm

profondeur 60 cm

Capacité

12 couverts standard

Pression eau

d’alimentation

0,05 ÷ 1 MPa (0,5 ÷ 10 bar)

4,3 psi – 145 psi

Tension

d’alimentation

Voir étiquette des caractéristiques

Puissance

totale absorbée

Voir étiquette des caractéristiques

Fusible

Voir étiquette des caractéristiques

Cet appareil est conforme aux

Directives Communautaires

suivantes :

- 73/23/CEE du 19/02/73 (Basse

Tension) et modifications suivantes

- 89/336/CEE du 03/05/89

(Compatibilité Electromagnétique)

et modifications suivantes

-97/17/CE (étiquetage)

-20002/96/CE (DEEE)

Raccordement électrique

Si votre appareil est muni d'une fiche avec fusible 13

ampères, cette dernière peut être branchée dans une

prise 13 ampères et vous pouvez utiliser votre appa-

reil immédiatement. Avant toute utilisation de l'appa-

reil, lisez attentivement les instructions suivantes.

ATTENTION ! CET APPAREIL DOIT ETRE RE-

LIE A LA TERRE.

CES OPERATIONS DOIVENT ETRE EFFECTUEES

PAR UN ELECTRICIEN QUALIFIE.

Remplacement du fusible.

En cas de remplacement d'un fusible défectueux, uti-

lisez toujours un fusible BS 1362 homologué ASTA de

13 ampères. Le couvercle du fusible doit toujours être

remis en place. En cas de perte du couvercle du fusi-

ble, n'utilisez pas la fiche tant que le couvercle n'aura

pas été remplacé.

Couvercles de fusible de rechange.

En cas d'utilisation d'un couvercle de rechange, il faut

que ce dernier soit bien de la même couleur que la

marque colorée ou que la couleur imprimée en relief à

la base de la fiche. Commandez directement vos cou-

vercles de fusible de rechange au dépôt de pièces

détachées le plus proche de votre domicile.

Dépose de la fiche.

Si l'appareil est muni d'une fiche moulée ne pouvant

pas être câblée de nouveau et qu'il faut déposer pour

ajouter une rallonge ou pour réacheminer le câble d'ali-

mentation à travers des partitions, des unités, etc.,

contrôlez que :

- la fiche est bien remplacée par une fiche avec fusi-

ble 13 ampères pouvant être câblée de nouveau por-

tant la marque BSI;

ou bien que :

- le câble d'alimentation est bien directement raccordé

à une prise de 13 ampères et commandé par un inter-

rupteur (conformément à BS 5733) accessible sans

qu'il faille déplacer l'appareil.

Mise au rebut de la fiche.

Avant d'éliminer la fiche, rendez ses broches inutilisa-

bles. Vous éviterez ainsi que la fiche ne puisse être

branchée accidentellement dans une prise.

Instructions pour le raccordement du câble à un

autre type de fiche :

Important : Les fils du conducteur d'alimentation sont

colorés conformément aux normes en vigueur comme

suit :

vert et jaune - terre

bleu - neutre

marron - phase

Du moment que les couleurs des fils du conducteur

d'alimentation pourraient ne pas correspondre au mar-

quage des couleurs qui repèrent les cosses sur la fi-

che, nous conseillons de procéder comme suit :

- raccordez le fil vert et jaune à la cosse marquée

"E" ou bien de couleur verte ou verte et jaune.

- raccordez le fil marron à la cosse marquée "L" ou de

couleur rouge.

- raccordez le fil marron à la cosse marquée "N" ou de

couleur noire.

En cas d'utilisation d'une fiche 13 ampères (BS 1363),

montez un fusible de 13 ampères. Une fiche de 15

ampères doit être protégée par un fusible 15 ampères

monté dans la fiche / dans l'adaptateur ou dans le

tableau de distribution.

En cas de doute sur l'alimentation électrique du dis-

positif, consultez un électricien qualifié avant toute uti-

lisation.

Raccordement d'un autre type de fiche.

Les fils de ce conducteur d'alimentation sont colorés

conformément aux normes en vigueur comme suit :

BLEU NEUTRE (N)

MARRON PHASE (L)

VERT ET JAUNE TERRE (E) ou

Mise au rebut de l'appareil.

Avant d'éliminer l'appareil, débarrassez-le de sa fiche

en coupant le câble d'alimentation le plus près possi-

ble du corps de la fiche. Puis éliminez-la comme dé-

crit plus haut.

ATTENTION :

La fiche du lave-vaisselle doit toujours être accessi-

ble même en cas d'installation d'un lave-vaisselle en-

castré pour pouvoir effectuer les opérations d'entre-

tien en toute sécurité.

Nous déclinons toute responsabilité en cas de non-

respect des normes énumérées ci-dessus.

Vue densemble

Description de lappareil

1. Panier supérieur

2. Bras de lavage supérieur

3. Clayettes rabattables

4. Réglage hauteur du panier

5. Panier inférieur

6. Bras de lavage inférieur

7. Panier à couverts

8. Filtre lavage

9. Réservoir à sel

10. Bacs produit de lavage et réservoir à

produit de rinçage

11. Plaque signalétique

12. Tableau de bord

***

*** Uniquement pour modèles tout intégrables.

* Présent uniquement sur certains modèles.

Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.

Tableau de bord

Bouton

Sélection

programme

Voyant Lavage

et 3h. Départ

différé*

Touche et voyant

Marche/Arret

Touche et Voyant

Pastilles

multifonction*

Touche et voyant

Départ différé*

Touche et voyant

Demi-charge*

Voyant ON-OFF

Voyant

Manque de sel*

Touche

ON-OFF/RESET

Voyant Manque de

produit de rinçage*

Voyant Séchage

et 6h. Départ

différé*

Voyant Fin et 9h.

Départ différé*

Charger les paniers

Avant de charger les paniers, débarrasser la vaisselle des

déchets plus importants et vider les verres et les coupes.

Après avoir chargé le lave-vaisselle, sassurer que les bras

de lavage tournent librement.

Panier du bas

Le panier du bas peut contenir des casseroles, des

couvercles, des assiettes, des saladiers, des couverts

etc.selon les Exemples de chargement.

Ranger de préférence sur les côtés du panier les plats de

service et les grands couvercles sans toutefois bloquer la

rotation du bras de lavage supérieur.

Certains modèles de lave-vaisselle sont pourvus de secteurs

rabattables

* qui peuvent être placés à la verticale pour ranger

des assiettes ou à lhorizontale pour ranger des casseroles et

des saladiers.

Panier à couverts

Le panier à couverts peut varier selon le modèle de lave-

vaisselle : séparable, non séparable, coulissant. Le panier à

couverts non séparable doit être placé obligatoirement dans

la partie avant du panier inférieur.

Le panier séparable se détache en deux parties, solution

pratique en cas de lavage d'une demi-charge (si cette option

est prévue pour le modèle de lave-vaisselle), il peut coulisser

parmi les accessoires fixes ou rabattables pour aller se placer

dans n'importe quel coin du panier du bas.

- Ils sont équipés tous deux de rabats coulissants qui

permettent de mieux ranger les couverts.

Ranger les couteaux et les ustensiles de cuisine pointus et

coupants dans le panier à couverts, pointes tournées vers le

bas, ou, à plat, sur les clayettes rabattables du panier

supérieur.

Exemples de rangement dans le panier à couverts

Panier du haut

Y ranger la vaisselle fragile et légère : verres, tasses à thé et à

café, soucoupes, saladiers bas, casseroles basses peu sales,

en suivant les Exemples de chargement.

 Tasses et tasses à café: les placer sur les étagères

rabattables

**.

 Couteaux longs et pointus, couverts de service : les placer

sur les étagères rabattables

**.

Régler la hauteur du panier supérieur

Pour optimiser le rangement de la vaisselle, possibilité de régler le

panier supérieur en position haute ou basse :

Régler de préférence la hauteur du panier quand ce dernier

est VIDE.

Ne jamais soulever ou abaisser le panier dun seul côté.

ouvrir les butées des glissières du

panier à droite et à gauche et sortir le

panier. Positionner le panier en position

haute ou basse, le faire glisser le long

des glissières jusquà ce que les roues

avant entrent elles aussi et refermer les

butées (voir figure).

Si le panier est équipé de poignées

Espace double

* (voir figure), sortir le

panier du haut en fin de corse, saisir les

poignées sur les côtés du panier et

déplacer vers le haut ou vers le bas;

laisser retomber le panier sans le

lâcher.

Exemples de chargement du panier supérieur

Exemples de chargement du panier inférieur

Vaisselle nallant pas au lave-vaisselle

 Objets en bois, avec des manches en bois ou en corne ou

ayant des parties collées.

 Objets en aluminium, cuivre, laiton ou étain.

 Vaisselle en plastique thermorésistant.

 Porcelaines anciennes ou peintes à la main.

 Argenterie ancienne. Les pièces dargenterie non ancienne

peuvent par contre être lavées avec un programme délicat

après sêtre assuré quelles ne touchent pas à dautres métaux.

Nous conseillons dutiliser de la vaisselle lavable au lave-

vaisselle.

* Présent uniquement sur certains modèles.

** Leur nombre et leur position varient.

Mise en marche et

utilisation

Charger le produit de lavage

Un bon résultat de lavage dépend aussi dun bon

dosage du produit de lavage. Un excès de produit

de lavage ne lave pas mieux et pollue

lenvironnement.

Nutiliser que du produit de lavage spécial

lave-vaisselle.

NE PAS UTILISER de produits pour laver la

vaisselle à la main.

Une utilisation excessive de produit de lavage

peut laisser des résidus de mousse en fin de

cycle.

L'utilisation de pastilles n'est conseillée que

pour les modèles qui prévoient l'option

PASTILLES MULTIFONCTION.

Pour obtenir des performances de lavage et

de séchage optimales, utiliser des produits de

lavage en poudre, du liquide de rinçage et du sel.

bac A : Produit de lavage

bac B : Produit de prélavage

1. Appuyer sur la touche D pour

ouvrir le couvercle C.

2. Pour doser le produit de lavage

se reporter au Tableau des

programmes:

 en poudre : bacs A et B.

 pastilles : si le programme en

prévoit 1, placer cette dernière

dans le bac A et fermer le

couvercle; sil en prévoit 2, mettre la deuxième dans le

fond de la cuve.

3. Eliminer les résidus de produit de lavage sur les bords

du bac et fermer le couvercle jusquau déclic.

* Présent uniquement sur certains modèles.

Mettre en marche le lave-vaisselle

1. Ouvrir larrivée deau.

2. Appuyer sur la touche ON-OFF : tous les voyants

du bandeau de commande sallument pendant

quelques secondes.

3. Ouvrir la porte et doser le produit de lavage (voir

plus bas).

4. Charger les paniers (voir Charger les paniers) et

fermer la porte.

5. Pour sélectionner le programme souhaité, tourner

le bouton de SÉLECTION PROGRAMME dans le sens

des aiguilles dune montre : amener le repère en

face du symbole ou du numéro du programme. Le

voyant de la touche MARCHE/Arret flashe.

6. Sélectionner les options de lavage

* (voir ci-

contre).

7. Appuyer sur la touche MARCHE pour démarrer, le

voyant cesse de flasher (lumière fixe). Le voyant

correspondant au lavage sallume pour signaler le

démarrage du programme.

8. A la fin du programme, la touche FIN sallume

(lumière fixe). Eteindre lappareil par pression sur la

touche ON-OFF, fermer le robinet de leau et

débrancher la fiche de la prise de courant.

9. Attendre quelques minutes avant de sortir la

vaisselle pour éviter de se brûler. Décharger les

paniers en commençant par celui du bas.

Modifier un programme en cours

En cas derreur de sélection dun programme, il est

possible de le modifier, à condition quil vienne tout

juste de démarrer : pour changer un cycle de lavage

en cours, éteindre puis rallumer lappareil par une

pression prolongée sur la touche ON/OFF,

sélectionner ensuite le nouveau programme et les

options désirées.

Introduire de la vaisselle en cours de lavage

Appuyer sur la touche Marche/Arret, (la touche se met

à flasher). ouvrir la porte en faisant attention à la

vapeur chaude qui séchappe et introduire la vaisselle.

Appuyer sur la touche Marche/Arret (lumière fixe) : le

cycle redémarre.

Appuyer sur la touche Marche/Arret pour mettre

lappareil en pause, le programme et le départ différé

éventuellement sélectionné sont stoppés.

Pendant cette phase, aucun changement de

programme nest possible.

Interruptions accidentelles

En cas douverture de la porte en cours de lavage ou

de coupure de courant, le programme sarrête. Il

redémarre du point où il a été interrompu dès que le

courant revient ou que la porte est refermée.

Options de lavage*

La sélection, la modification ou lannulation des

OPTIONS nest possible quaprès avoir choisi le

programme de lavage et avant dappuyer sur la

touche Marche/Arret.

Seules les options compatibles avec le programme

choisi peuvent être sélectionnées. Si une option nest

pas compatible avec le programme sélectionné, (voir

tableau programmes) la led correspondante clignote

rapidement 3 fois.

En cas de sélection dune option incompatible avec une

option ou un programme de lavage précédemment

sélectionné, celle-ci clignote 3 fois de suite puis séteint,

tandis que la dernière sélection effectuée reste allumée.

Pour désactiver une option sélectionnée par erreur,

appuyer à nouveau sur la touche correspondante.

La page charge ...

Whirlpool LKF 720 EX.R Mode d'emploi

Marque: Whirlpool

Modèle: LKF 720 EX.R

Catégorie: Lave-vaisselle

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool LKF 720 EX.R User guide

Documents connexes

Autres documents

Indesit DSR 57M17 NX Mode d'emploi