Dometic CAM60ADR Mode d'emploi

CAM60ADR

Rear View Video Camera

Installation and Operating Manual . . . . . . 9

Rückfahrvideokamera

Montage- und Bedienungsanleitung . . . 20

Caméra vidéo de recul

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . 31

Cámara de vídeo de marcha atrás

Instrucciones de montaje y de uso . . . . .42

Câmara de marcha-atrás

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . 53

Videocamera per la retromarcia

Istruzioni di montaggio e d’uso . . . . . . . . 64

Achteruitrijvideocamera

Montagehandleiding en

gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 75

Bakvideokamera

Monterings- og betjeningsvejledning. . . 86

Backningsvideokamera

Monterings- och bruksanvisning . . . . . . . 97

Ryggevideokamera

Monterings- og bruksanvisning . . . . . . . 108

Peruutusvideokamera

Asennus- ja käyttöohje. . . . . . . . . . . . . . 120

Видеокамера заднего вида

Инструкция по монтажу

и эксплуатации. . . . . . . . . . . . . . . . . . . . .131

Kamera cofania

Instrukcja montażu i obsługi . . . . . . . . . 142

Cúvacia kamera

Návod na montáž a uvedenie

do prevádzky . . . . . . . . . . . . . . . . . . . . . 153

Couvací kamera

Návod k montáži a obsluze . . . . . . . . . . 164

Tol a t ó kam e r a

Szerelési és használati útmutató . . . . . . 176

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

DRIVING SUPPORT

PERFECTVIEW

CAM60ADR-IO-16s.book Seite 1 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR-IO-16s.book Seite 2 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR

3

1 2 3

4

9

6

8

5

7

10 11

12

1

CAM60ADR-IO-16s.book Seite 3 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR

4

2

3

4

5

CAM60ADR-IO-16s.book Seite 4 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR

5

1

2

3

Ø 16 mm

6

3

1

2

7

CAM60ADR-IO-16s.book Seite 5 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR

6

90°

8

9

0

a

b

c

CAM60ADR-IO-16s.book Seite 6 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR

7

d

~50°

2.

1.

e

f

A

B

g

CAM60ADR-IO-16s.book Seite 7 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR

8

h

CAM60ADR-IO-16s.book Seite 8 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR Explanation of symbols

EN

9

Please read this instruction manual carefully before installation and first use, and store

it in a safe place. If you pass on the product to another person, hand over this instruc-

tion manual along with it.

Contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Information on the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

8 Mounting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

9 Cleaning and caring for the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

10 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

12 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1 Explanation of symbols

!

A

I

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or serious injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair the function

of the product.

NOTE

Supplementary information for operating the product.

CAM60ADR-IO-16s.book Seite 9 Donnerstag, 7. Juli 2016 1:21 13

Safety and installation instructions CAM60ADR

EN

10

2 Safety and installation instructions

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and excess voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

Please observe the prescribed safety instructions and stipulations from the vehicle

manufacturer and service workshops.

!

WARNING!

Inadequate supply cable connections could result in short circuits, which could have as

a consequence that:

• Cable fires occur

• The airbag is triggered

• Electronic control devices are damaged

• Electric functions fail (indicators, brake light, horn, ignition, lights)

A

NOTICE!

To prevent the risk of short circuits, always disconnect the negative terminal of the vehi-

cle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be discon-

nected.

Please observe the following instructions:

• When working on the following cables, only use insulated cable lugs, plugs and flat push-on

receptacles:

– 30 (direct supply from positive battery terminal)

–15 (connected positive terminal, behind the battery)

– 31 (return line from the battery, earth)

– L (indicator lights left)

– R (indicator lights right)

Do not use terminal strips.

• Use a crimping tool to connect the cables.

• When connecting to cable 31 (earth), screw the cable

– to the vehicle's earth bolt with a cable lug and a gear disc or

– to the sheet-metal bodywork with a cable lug and a self-tapping screw.

Ensure that there is a good earth connection.

CAM60ADR-IO-16s.book Seite 10 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR Safety and installation instructions

EN

11

If you disconnect the negative terminal of the battery, all data stored in the volatile memories will

be lost.

• The following data must be set again, depending on the vehicle equipment options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the appropriate operating instructions.

Observe the following installation instructions:

!

CAUTION!

• Secure the parts installed in the vehicle in such a way that they cannot become loose

under any circumstances (sudden braking, accidents) and cause injuries to the

occupants of the vehicle.

• Secure any parts of the system covered by the bodywork in such a manner that they

cannot be come loose or damage other parts and cables or impair vehicle functions

(steering, pedals, etc).

• Always follow the safety instructions of the vehicle manufacturer.

Some work (e.g. on retention systems such as the AIRBAG etc.) may only be per-

formed by qualified specialists.

A

NOTICE!

• To prevent damage when drilling, make sure there is sufficient space on the other

side for the drill head to come out.

• Deburr all drill holes and treat them with a rust-protection agent.

Observe the following instructions when working with electrical parts:

A

NOTICE!

• When testing the voltage in electrical cables, only use a diode test lamp or a voltme-

ter.

Test lamps with an illuminant take up voltages which are too high and which can dam-

age the vehicle's electronic system.

• When making electrical connections, ensure that:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp edged ducts without protection.

• Insulate all connections.

• Secure the cables against mechanical wear with cable binders or insulating tape,

for example to existing cables.

CAM60ADR-IO-16s.book Seite 11 Donnerstag, 7. Juli 2016 1:21 13

Scope of delivery CAM60ADR

EN

12

The camera is watertight in accordance with IP69K. The seals on the camera can therefore

withstand a high-pressure cleaner. Nevertheless, keep a distance of at least 50 cm between

the nozzle of the high pressure cleaner and the camera.

Always observe the following instructions when handling the camera:

• Do not open the camera, as this impairs the sealing and the function of the camera (fig. 4,

page 4).

• Do not pull at the cables, as this impairs the sealing and the function of the camera (fig. 5,

page 4).

• The camera is not suitable for submerged operation.

3Scope of delivery

4 Accessories

Available as accessory (not included in scope of delivery):

5Intended use

The CAM60ADR camera (ref. no. 9600000057) is designed primarily for use in vehicles under

extreme conditions. It can be used in video systems to observe the space around the vehicle from

the driver's seat when manoeuvring or parking, for example.

CAM60ADR is compliant to ADR and can be used in vehicles for transport of hazardous goods.

!

No. in

fig. 6,

page 5

Quantity Description Reference no.

1 1 CAM60ADR (compliant to ADR) 9600000057

2 1 Camera bracket 9102200166

32Side covers

––Fastening material

Description Reference no.

Heavy duty system cable 20 m, compliant to ADR 9102200071

WARNING!

Risk of injury!

Since rear view systems are designed merely as an additional aid for reversing, it does

not relieve you of the duty to take proper care when reversing.

CAM60ADR-IO-16s.book Seite 12 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR Technical description

EN

13

6 Technical description

The camera with integrated microphone, which is encased in aluminium housing, transmits image

and sound to a monitor via a cable. The infrared LEDs improve night vision.

The camera transmits the image as if you are looking in the rear mirror.

The camera consists of the following main elements:

7 Information on the electrical connections

7.1 Laying cables

A

Please observe the following instructions:

• As far as possible, use original openings or alternative openings for the connecting cable duct,

e.g. the paneling edges, ventilation grilles or blank panels. If no openings are available, you

must drill holes for the cables. Check beforehand that there is sufficient room for the drill head

to come out on the other side.

• Wherever possible lay cables inside the vehicle, as they are better protected inside than outside

the vehicle.

If you do need to lay a cable outside the vehicle, ensure that it is well secured (use additional

cable ties, insulating tape, etc.).

• To prevent damage to the cables, when laying them ensure that there is sufficient distance to

hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heater,

etc.). Use corrugated piping or other protective materials to protect against mechanical wear.

• Screw on the plug connections of the connecting cables to protect against water penetration

(fig. e, page 7).

No. in

fig. 7,

page 5

Description

16-pin connection cable

2Infrared LEDs

3Microphone

NOTICE! Risk of damage!

• To prevent damage, when drilling ensure that there is sufficient space on the other

side for the drill head to come out.

• Cables and connections which are not properly installed will cause malfunctions or

damage to components. Correct installation of cables and connections is the basic

prerequisite for lasting and trouble-free operation of the retrofitted components.

• The cables may not be exposed for long periods to solvents such as benzine, as the

solvents can damage the cable.

CAM60ADR-IO-16s.book Seite 13 Donnerstag, 7. Juli 2016 1:21 13

Mounting the camera CAM60ADR

EN

14

• When laying electric connections, ensure that

– They are not kinked or twisted

– They do not rub on edges

– They are not laid in sharp edged ducts without protection (fig. 3, page 4)

• Attach the cables securely in the vehicles to prevent tripping hazards. Use cable binders,

insulating tape or glue the cables in place.

• Protect every through-hole made in the bodywork against water penetration, e.g. by using a

cable with a sealant and by spraying the cable and the the cable sleeve with sealant.

I

8 Mounting the camera

8.1 Tools required

For installation and assembly you will require the following tools:

• Drill bit set (fig. 1 1, page 3)

• Drill (fig. 1 2, page 3)

• Screwdriver (fig. 1 3, page 3)

• Set of ring or open-ended spanners (fig. 1 4, page 3)

• Measuring ruler (fig. 1 5, page 3)

• Hammer (fig. 1 6, page 3)

• Centre punch (fig. 1 7, page 3)

To make and test the electrical connection, the following tools are required:

• Diode test lamp (fig. 1 8, page 3) or voltmeter (fig. 1 9, page 3)

• Insulating tape (fig. 1 11, page 3)

• Cable bushing sleeves, if necessary

To fasten the cables you may require additional cable binders.

NOTE

Do not start sealing the through-holes until all installation work has been finished for the

camera, and the required cable lengths have been established.

CAM60ADR-IO-16s.book Seite 14 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR Mounting the camera

EN

15

8.2 Mounting the camera

!

I

Observe the following installation instructions:

• To provide a suitable viewing angle, the camera must be attached at a height of at least 2 m.

Ensure that you have a firm place from which to work when mounting the camera.

• Ensure that the installation location of the camera is sufficiently firm (e.g. to prevent the camera

from being knocked down by branches that may brush over the roof of the vehicle).

• Mount the camera bracket horizontally and in the middle of the rear of the vehicle (fig. 8,

page 6).

• The most secure type of attachment is with screws fitted through the body. Please observe the

following instructions:

– There must be sufficient space for the mounting procedure behind the chosen installation

location.

– Suitable measures must be taken to prevent water penetrating through any holes made

(e.g. by using screws and sealant and/or spraying the outer attachment parts with a

sealant).

– The location on the body where you wish to attach the camera must be rigid enough to

allow the camera to be tightly fastened.

• Check beforehand that there is sufficient room for the drill head to come out on the other side

(fig. 2, page 4).

• If you are not sure about the location you have chosen, consult the vehicle manufacturer or

dealer.

I

When mounting the camera, proceed as follows:

➤ Hold the camera on the chosen location and mark at least two different points for the drill holes

(fig. 9, page 6).

➤ Using a hammer and centre punch, gently pre-punch the previously marked points to prevent

the drill head from slipping off.

CAUTION!

Select a location for the camera and attach it so securely that it cannot under any

circumstances fall off and injure bystanders (e.g. by being knocked off by branches

brushing over the roof of the vehicle).

NOTE

If installing the camera alters the vehicle height or length specified in the vehicle

documents, your vehicle must be inspected by the appropriate authorities.

Make sure that you are in possession of documents verifying that your vehicle has

passed this inspection.

NOTE

We recommend greasing the threads of the bolts to prevent corrosion.

CAM60ADR-IO-16s.book Seite 15 Donnerstag, 7. Juli 2016 1:21 13

Mounting the camera CAM60ADR

EN

16

If you want to screw on the camera with self-tapping screws (fig. 0, page 6)

A

➤ Drill Ø 4 mm holes at the points you have just marked.

➤ Deburr all drill holes and apply rust-protection.

➤ Screw the camera bracket on with the 5 x 20 mm self-tapping screws.

If you would like to attach the camera with threaded screws fitted through the

construction (fig. a, page 6)

A

➤ Drill Ø 6.5 mm holes at the points you have just marked.

➤ Deburr all drill holes and apply rust-protection.

➤ Screw the camera bracket on with the M5 x 20 mm threaded screws.

Depending on the thickness of the construction, you may require longer threaded screws.

Creating a through-hole for the camera connection cable (fig. b, page 6)

I

A

➤ Drill a hole of Ø 16 mm near the camera.

➤ Deburr all drill holes that have been made in the sheet metal and apply rust-protection.

➤ Place cable sleeves in all sharp edged ducts.

NOTICE! Risk of damage!

The holder may only be attached to steel panels with a minimum thickness of 1.5 mm

using self-tapping screws.

NOTICE! Risk of damage!

Ensure that that nuts cannot be pulled through the body shell when they are tightened.

Use larger washers or metal plates if necessary.

NOTE

If possible, use available openings – such as ventilation grilles – to feed the connection

cables through. If there are no existing openings, you must drill a hole with a

16 mm diameter.

NOTICE! Risk of damage!

Ensure that there is sufficient space on the other side for the drill head to come out

CAM60ADR-IO-16s.book Seite 16 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR Mounting the camera

EN

17

Mounting the camera

A

➤ Push the camera into the camera bracket.

➤ Attach the camera loosely with the two screws M3 x 8 mm in the slots (fig. c, page 6).

➤ Align the camera provisorily so that the lens is at an angle of approx. 50° to the perpendicular

axis of the vehicle (fig. d, page 7).

A

Connecting the camera

I

➤ Guide the camera cable into the vehicle interior.

➤ Insert the plug of the camera cable into the socket of the extension cable.

➤ Screw on the plug connections of the connecting cables to protect against water penetration

(fig. e, page 7).

Aligning the camera

I

➤ Use the monitor image to align the camera:

The monitor image should show the bottom edge of the rear or the bumper of your

vehicle (A). The middle of the bumper should be in the middle of the screen. (fig. g,

page 7).

➤ Check the function of the camera after you have connected it to a monitor.

NOTICE! Risk of damage!

Only use the screws supplied to mount the camera in the camera bracket.

Longer screws will damage the camera.

NOTICE! Risk of damage!

Never mount the camera without the camera guard.

NOTE

• Lay the camera cable so that should you need to remove the camera, you can access

the plug connection between the camera and the extension cable easily. This con-

siderably eases dismantling work.

• To minimise corrosion in the plug, apply a small amount of grease – such as pin

grease – inside the plug.

• Additional extension cables are available on request (see chapter “Accessories” on

page 12).

NOTE

If necessary before aligning the camera connect the camera to a monitor and to a

power supply (see connecting diagram, fig. f, page 7

CAM60ADR-IO-16s.book Seite 17 Donnerstag, 7. Juli 2016 1:21 13

Cleaning and caring for the camera CAM60ADR

EN

18

Fastening the camera

➤ Thighten the two screws in the slots of the camera bracket.

➤ Mount the side covers with the two screws M3 x 8 mm in the middle drill holes (fig. h,

page 8).

9 Cleaning and caring for the camera

A

➤ Clean the camera with a soft, damp cloth from time to time.

10 Guarantee

The statutory warranty period applies. If the product is defective, please contact the

manufacturer's branch in your country (see the back of the instruction manual for the addresses) or

your retailer.

For repair and guarantee processing, please send the following items:

• Defect components

• A copy of the receipt with purchasing date

• A reason for the claim or description of the fault

11 Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever possible.

M

If you wish to finally dispose of the product, ask your local recycling centre or specialist

dealer for details about how to do this in accordance with the applicable disposal regu-

lations.

NOTICE! Risk of damage!

Do not use sharp or hard objects to clean the device as these may damage the device.

CAM60ADR-IO-16s.book Seite 18 Donnerstag, 7. Juli 2016 1:21 13

CAM60ADR Technical data

EN

19

12 Technical data

Approvals

The device has E13 certification.

PerfectView CAM 60ADR

Ref. no.: 9600000057

Image sensor: 1/3" CCD

Pixels: Approx. 290,000 pixels

Video standard: PAL, 1 Vpp

Sensitivity: < 0.5 lux

Viewing angle: Approx. 69° vertical

Approx. 92.5° horizontal

Approx. 120° diagonal

Operating voltage: 11 – 16 Vg

Consumption: 4.8 W

Operating temperature: –30 °C bis +70 °C

Protection class: IP69K

Vibration resistance: 10 g

Dimensions W x H x D

(with bracket):

80 x 75 x 62 mm

Weight: Approx. 0.3 kg

E

CAM60ADR-IO-16s.book Seite 19 Donnerstag, 7. Juli 2016 1:21 13

Erklärung der Symbole CAM60ADR

DE

20

Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig durch und

bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe des Produktes an den

Nutzer weiter.

Inhaltsverzeichnis

1 Erklärung der Symbole. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

2 Sicherheits- und Einbauhinweise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

4 Zubehör . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

5 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

6 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

7 Hinweise zum elektrischen Anschluss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

8 Kamera montieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

9 Kamera pflegen und reinigen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

10 Gewährleistung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

11 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

12 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

1 Erklärung der Symbole

!

A

I

WARNUNG!

Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer Verletzung führen.

VORSICHT!

Sicherheitshinweis: Nichtbeachtung kann zu Verletzungen führen.

ACHTUNG!

Nichtbeachtung kann zu Materialschäden führen und die Funktion des Produktes

beeinträchtigen.

HINWEIS

Ergänzende Informationen zur Bedienung des Produktes.

CAM60ADR-IO-16s.book Seite 20 Donnerstag, 7. Juli 2016 1:21 13

La page charge ...

Dometic CAM60ADR Mode d'emploi

Ce manuel convient également à

Dometic CAM60ADR Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents