Dometic DW2410 Manuel utilisateur

User manual

Dishwasher

Notice

d'utilisation

Lave-vaisselle

Benutzer-

information

Geschirrspüler

Istruzioni per

l’uso

Lavastoviglie

DW2410

Contents

Safety information 2

Product description 3

Control panel 4

Use of the appliance 6

Setting the water softener 6

Use of dishwasher salt 7

Use of rinse aid 7

Loading cutlery and dishes 8

Use of detergent 9

Setting and starting a washing programme

10

Washing programmes 11

Care and cleaning 11

What to do if… 12

Technical data 14

Installation 14

Water connection 15

Electrical connection 16

Environment concerns 16

Subject to change without notice

Safety information

For your safety and correct operation of

the appliance, read this manual carefully

before installation and use. Always keep

these instructions with the appliance

even if you move or sell it. Users must

fully know the operation and safety fea-

tures of the appliance.

Correct use

• The appliance is designed exclusively for

domestic use.

• Only use the appliance to clean household

utensils that are applicable for dishwash-

ers.

• Do not put solvents in the appliance. Risk

of explosion.

• Put the knives and all items with sharp

points in the cutlery basket with their

points down. If not, put in a horizontal po-

sition in the main basket.

• Use only branded products for dishwash-

ers (detergent, salt, rinse aid).

• If you open the door while the appliance is

in operation, hot steam can escape. Risk

of skin burns.

•Do not remove dishes from the dishwasher

before the end of the washing programme.

• When the washing programme is comple-

ted, disconnect the mains plug from the

mains socket and close the water tap.

• Only an authorised service engineer can

repair this appliance. Use only original

spare parts.

• Do not do repairs yourself to prevent injury

and damage to the appliance. Always con-

tact your local Service Force Centre.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or

lack of experience and knowledge must

not use the appliance. They must have su-

pervision or instruction for the operation of

the appliance by a person responsible for

their safety.

• Obey the safety instructions from the man-

ufacturer of the dishwasher detergent to

prevent burns to eyes, mouth and throat.

• Do not drink the water from the dishwash-

er. Detergent residues can stay in your ap-

pliance.

• Always close the door when you do not

use the appliance to prevent injury and not

to stumble over the open door.

• Do not sit or stand on the open door.

Child safety

• Only adults can use this appliance. Chil-

dren must get supervision to make sure

that they do not play with the appliance.

• Keep all the packaging away from children.

There is a risk of suffocation.

• Keep all detergents in a safe area. Do not

let children touch the detergents.

• Keep children away from the appliance

when the door is open.

2

Installation

• Make sure that the appliance is not dam-

aged because of transport. Do not con-

nect a damaged appliance. If necessary,

contact the supplier.

• Remove all packaging before first use.

• A qualified and competent person must do

the electrical installation.

• A qualified and competent person must do

the plumbing installation.

• Do not change the specifications or modify

this product. Risk of injury and damage to

the appliance.

• Do not use the appliance:

– if the mains cable or water hoses are

damaged,

– if the control panel, worktop or plinth

area are damaged, that you can get ac-

cess to the inner side of the appliance.

Contact your local Service Force Centre.

• Do not drill into the sides of the appliance

to prevent damage to hydraulic and elec-

trical components.

Warning! Carefully obey the

instructions for electrical and water

connections.

Product description

1

2

3

4

5

6

1 Rinse aid dispenser

2 Spray arm

3 Fine filter

4 Detergent dispenser

5 Coarse filter

6 Salt container

3

The rating label is on the back of appli-

ance.

Control panel

1 2 3

4

AB

5

1 On/off button

2 Delay start button / (Delay start)

3 Programme selection/cancel button / (Programme/ Cancel)

4 Indicator lights

5 Programme indicator lights

Indicator lights

Programme-in-progress – Comes on when you select a washing pro-

gramme.

– Stays on for all the duration of the washing pro-

gramme.

– Goes off at the end of the washing programme.

Salt

1)

Comes on when it is necessary to fill the salt con-

tainer. Refer to 'Use of dishwasher salt'.

After you fill the container, the salt indicator light

can continue to stay on for some hours. This does

not have an unwanted effect on the operation of

the appliance.

4

Indicator lights

End Comes on when the washing programme is com-

pleted. Auxiliary functions:

• Level of the water softener.

• Activation/deactivation the audible signals.

• An alarm if the appliance has a malfunction.

1) When the salt container is empty, the related indicator light does not come on while a washing

programme operates.

Programme selection/cancel button

Use the programme selection/cancel button

for these operations:

• To set the washing programme. Refer to

the chapter 'Setting and starting a washing

programme'.

• To set the water softener. Refer to the

chapter 'Setting the water softener'.

• To deactivate/activate the audible signals.

Refer to the section 'Audible signals'.

• To cancel a washing programme in pro-

gress. Refer to the chapter 'Setting and

starting a washing programme'.

Delay start button

Use the delay start button to delay the start

of the washing programme with an interval of

3 hours. Refer to the chapter 'Setting and

starting a washing programme'.

Setting mode

The appliance is in setting mode when all the

programme indicator lights are off and the

end indicator light flashes.

The appliance must be in setting mode for

these operations:

– To set a washing programme.

– To set the water softener level.

– To deactivate/activate the audible signals.

If a programme indicator light is on, cancel

the programme to go back to the setting

mode. Refer to the chapter "Setting and

starting a washing programme".

Programme indicator lights A and B

Apart the selection of the corresponding

washing programme, these lights have an

auxiliary functions:

• The adjustment of the water softener level.

• Deactivation/activation of the audible sig-

nals.

Audible signals

You can hear an audible signal:

• At the end of the washing programme.

• When the appliance has a malfunction.

The activation of the audible signals is set at

the factory.

Do these steps to deactivate the audible sig-

nals:

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Press and hold the programme selection/

cancel button until programme indicator

light A flashes and programme indicator

light B comes on.

4. Press the programme selection/cancel

button again.

– Programme indicator light A comes on.

– Programme indicator light B starts to

flash.

5. Wait until programme indicator light A

goes off.

– Programme indicator light B continues

to flash.

– The end indicator light comes on.

The audible signals are activated.

6. Press the programme selection/cancel

button again.

– The end indicator light goes off.

The audible signals are deactivated.

7. Switch off the appliance to save the op-

eration.

Do these steps to activate the audible sig-

nals:

1. Do the above procedure until the end in-

dicator light comes on.

5

Use of the appliance

Refer to the following instructions for each

step of procedure:

1. Make a check if the water softener level

is correct for the water hardness in your

area. If necessary set the water softener.

2. Fill the salt container with dishwasher salt.

3. Fill the rinse aid dispenser with rinse aid.

4. Load cutlery and dishes into the dish-

washer.

5. Set the correct washing programme for

the type of load and soil.

6. Fill the detergent dispenser with the cor-

rect quantity of detergent.

7. Start the washing programme.

If you use detergent tablets, refer to the

chapter 'Use of detergent'.

Setting the water softener

The water softener removes minerals and

salts from the water supply. Minerals and

salts can have bad effect on the operation of

the appliance.

Water hardness is measured in equivalent

scales:

• German degrees (dH°).

• French degrees (°TH).

• mmol/l (millimol per litre - international unit

for the hardness of water).

•Clarke.

Adjust the water softener to the water hard-

ness in your area. If necessary, contact your

local water authority.

Water hardness

setting

°dH mmol/l °TH Clarke

>24 >4.2 >40 > 29 10

22- 24 3,9- 4,2 39- 40 27- 29 9

20- 22 3,5- 3,9 35- 39 25- 27 8

18- 20 3,2- 3,5 32- 35 23- 25 7

16- 18 2,8- 3,2 28- 32 20- 23 6

13- 16 2,3- 2,8 23- 28 17-20 5

10- 13 1,8- 2,3 18- 23 13- 17 4

7- 10 1,2- 1,8 12- 18 9- 13 3

4- 7 0.7- 1,2 7- 12 5- 9 2

< 4 < 0.7 < 7 < 5

1

1)

1) No use of salt required.

Electronic adjustment

The water softener is set at the factory

at level 5.

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Press and hold the programme selection/

cancel button.

4. Release the programme selection/cancel

button when programme indicator light A

starts to flash and programme indicator

light B comes on.

5. Wait until programme indicator light B

goes off.

– Programme indicator light A starts to

flash.

– The end indicator light starts to flash.

6. Press the programme selection/cancel

button one time.

– Programme indicator light A starts to

flash.

– The setting function of the water soft-

ener is activated.

– The end indicator light flashes to show

the level of the water softener.

Example: 5 flashes, pause, 5 flashes,

pause, etc... = level 5.

7. Press the programme selection/cancel

button one time to increase the water

softener level by one step.

8. Press the on/off button to save the oper-

ation.

6

Use of dishwasher salt

Caution! Only use dishwashers salt.

Types of salt that are not applicable for

dishwashers cause damage to the water

softener.

Caution! Grains of salt and salty water

on the bottom of the appliance can

cause corrosion. Fill the appliance with

salt before you start a washing

programme to prevent corrosion.

Do these steps to fill the salt container:

1. Turn the cap anticlockwise to open the

salt container.

2. Fill the salt container with 1 litre of water

(only the first operation).

3. Use the funnel to fill the salt container with

salt.

4. Remove the salt around the opening of

the salt container.

5. Turn the cap clockwise to close the salt

container.

It is normal that water overflows from the

salt container when you fill it with salt.

When you set the water softener to level 1,

the salt indicator light does not stay on.

Use of rinse aid

Caution! Only use branded rinse aid for

dishwashers.

Do not fill the rinse aid dispenser with

other products (e.g. dishwasher clean-

ing agent, liquid detergent). There is a

risk of damage to the appliance.

Rinse aid makes it possible to dry the

dishes without streaks and stains.

Rinse aid is automatically added during

the last rinsing phase.

Do these steps to fill the rinse aid dispenser:

7

1. Turn the filler receptacle (1) to open the

rinse aid dispenser.

2. Fill the rinse aid dispenser with rinse aid.

The red mark on the level indicator (2)

shows the maximum level.

3. Remove the spilled rinse aid with an ab-

sorbent cloth to prevent too much foam

during the subsequent washing pro-

gramme.

4. Turn the filler receptacle (1) to close the

rinse aid dispenser.

The capacity of the rinse aid dispenser

is approximately 140 ml. The quantity of

rinse aid is sufficient for approximately

40-70 washing programmes.

Adjust the dosage of rinse aid

Refer to the washing results (chapter 'What

to do if...'). Start with the lowest dosage.

1. Turn the arrow (3) clockwise to increase

the dosage.

2. Increase the dose if there are water drop-

lets or limescale on the dishes.

3. Fill the rinse aid dispenser when the rinse

aid comes near the bottom of the level

indicator.

Loading cutlery and dishes

Helpful hints and tips

Caution! Only use the appliance for

household utensils that are applicable

for dishwashers.

Do not use the appliance to clean objects

that can absorb water (sponges, household

cloths, etc.).

• Before you load cutlery and dishes, do

these steps:

– Remove all food remainings and debris.

– Make burnt, remaining food in pans soft.

• While you load cutlery and dishes, do

these steps:

– Load hollow items (e.g. cups, glasses

and pans) with the opening down.

– Make sure that water does not collect in

the container or in a deep base.

– Make sure that cutlery and dishes do not

lie inside one another.

– Make sure that cutlery and dishes do not

cover other cutlery and dishes.

– Make sure that glasses do not touch

other glasses.

– Put small objects in the cutlery basket.

• Plastic items and pans with non-stick

coatings can keep water droplets.

• Plastic items do not dry as well as porce-

lain and steel items.

• Put light items in the main basket. Make

sure that the items do not move.

Caution! Make sure that the spray arm

can move freely before you start a

washing programme.

Primary basket

Arrange the deep dishes and large lids

around the edge of the basket. Arrange items

on and below the cup racks. The water must

come to all parts of the dishes.

You can fold the cup racks to clean high

items.

8

Cutlery basket

Warning! Do not put long-bladed knives

in a vertical position to prevent injury.

Arrange long and/or sharp items of cutlery

horizontally in the primary basket. Be careful

with sharp items such as knives.

Use the cutlery basket for:

• forks and spoons with the handles down.

• knives with the handles up.

The cutlery basket has a cutlery grid that you

can remove.

Do not let the cutlery bond together.

Make sure that the spray arm can move

freely before you close the door.

Use of detergent

Only use detergents (powder, liquid or

tablet) that are applicable for dishwash-

ers.

Follow the data on the packaging:

• Dosage recommended by the manu-

facturer.

• Storage recommendations.

The instructions on the packaging usu-

ally refer to large dishwashers (12 set-

tings).

Do not use more than the correct quan-

tity of detergent to save an environment.

Fill with detergent

Do these steps to fill the detergent dispenser:

1. Open the door.

2. Fill the detergent dispenser with deter-

gent.

3. If you use detergent tablets, put the tablet

in the dispenser.

4. Close the door. Push the door until it

locks in position.

Use of detergent tablets

Put the detergent tablet in the detergent dis-

penser.

Some of the tablets contain agents such as:

• detergent

•rinse aid

• dishwasher salt.

Some types of tablets can contain other

agents.

Do these steps to use detergent tablets:

1. Make sure that the detergent tablets are

applicable for your water hardness. Refer

to the instructions from the manufacturer.

2. Set the lowest levels of water hardness

and rinse aid dosage.

It is not necessary to fill the salt container

and the rinse aid dispenser.

Do these steps when the drying results

are not satisfactory:

1. Fill the rinse aid dispenser with rinse aid.

2. Set the rinse aid dosage to the medium

position.

9

Do these steps to use the detergent

powder again:

1. Fill the salt container and the rinse aid

dispenser.

2. Set the water softener to the highest level.

3. Do a washing programme without

dishes.

4. Adjust the water softener. Refer to 'Set-

ting the water softener'.

5. Adjust the rinse aid dosage.

Different brands of detergent dissolve in

different times. Some detergent tablets

do not have the best cleaning results

during short washing programmes. Use

long washing programmes when you

use detergent tablets to fully remove the

detergent.

Setting and starting a washing programme

1. Close the door.

2. Press the on/off button.

– The end indicator light starts to flash.

3. Press the programme selection/cancel

button again and again to set the washing

programme. Refer to the chapter 'Wash-

ing programmes'.

– The washing programme indicator light

comes on.

– The washing programme starts.

When the washing programme oper-

ates, you cannot change the pro-

gramme. Cancel the washing pro-

gramme.

Warning! Only interrupt or cancel a

washing programme if necessary.

Caution! Open the door carefully. Hot

steam can come free.

Cancelling a washing programme

1. Press and hold the programme selection/

cancel button for approximately 3 sec-

onds.

– The programme indicator light goes

off.

– The end indicator light starts to flash.

2. Release the programme selection/cancel

button to cancel the washing pro-

gramme.

At this time you can do these steps:

1. Switch off the appliance.

2. Set a new washing programme.

Fill the detergent dispenser with detergent

before you set a new washing programme.

Interrupting a washing programme

Open the door.

• The programme stops.

Close the door.

• The programme continues from the point

of interruption.

Setting and starting a washing

programme with delay start

1. Press the on/off button.

2. Press the delay start button.

– The delay start indicator light comes

on.

3. Set a washing programme.

– The programme indicator light comes

on.

Do not open the door during the count-

down to prevent interruption of the

countdown. When you close the door

again, the countdown continues from

the point of interruption.

Cancelling a delay start:

1. Press the delay start button.

– The delay start indicator light goes off.

– The programme starts immediately.

End of the washing programme

Switch off the appliance in these conditions:

• The appliance stops automatically.

• The end indicator light comes on.

• The audible signals for the end of the pro-

gramme operate.

1. Press the on/off button.

2. Open the door.

3. For better drying results, keep the door

ajar for some minutes before you remove

the dishes.

Let the dishes cool down before you remove

them from the appliance. Hot dishes are

easily damaged.

10

Washing programmes

Programme Degree of soil Type of load Programme description

Heavy soil Crockery, cutlery,

pots and pans

Main wash up to 70°C

2 intermediate rinses

Final rinse

Drying

Normal soil Crockery and cut-

lery

Main wash up to 65°C

1 intermediate rinse

Final rinse

Drying

1)

Normal soil Crockery and cut-

lery

Main wash up to 55°C

1 intermediate rinse

Final rinse

Drying

Normal or light soil Crockery and cut-

lery

Main wash up to 50°C

1 intermediate rinse

Final rinse

Normal or light soil Delicate crockery

and glassware

Main wash up to 40°C

1 intermediate rinse

Final rinse

1) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.

Consumption values

Programme Duration (in minutes) Energy (in kWh) Water (in litres)

100-110 0,9-1,0 9-10

80-90 0,7-0,8 7-8

140-150 0,5-0,6 7-8

40 0,5 8

35 0,4 8

The pressure and temperature of the

water, the variations of power supply

and the quantity of dishes can change

these values.

Care and cleaning

Warning! Switch the appliance off

before you clean the filters.

Cleaning the filters

Caution! Do not use the appliance

without filters. Make sure that the

installation of the filters is correct.

Incorrect installation will cause

unsatisfactory washing results and

damage to the appliance.

The dishwasher has two filters:

1. coarse filter

2. fine filter

11

Do these steps to clean the filters:

1. Open the door.

2. Remove the basket.

3. Remove the filters in the bottom of the

appliance.

4. Clean the filters below running water.

5. Put the filters back.

6. Close the door.

Cleaning the spray arm

Regularly examine the spray arm. Remove

remaining food from the holes in the spray

arm.

Do these steps to remove the spray arm:

1. Turn the nut clockwise.

2. Remove the spray arm.

3. Clean the holes fully.

External cleaning

Clean the external surfaces of the appliance

and control panel with a damp soft cloth.

Only use neutral detergents. Do not use

abrasive products, scouring pads or solvents

(acetone, trichloroethylene etc...).

Frost precautions

Caution! Do not install the appliance

where the temperature is below 0 °C.

The manufacturer is not responsible for

damage because of frost.

If not possible, empty the appliance and

close the door. Disconnect the water inlet

hose and remove water from the water inlet

hose.

What to do if…

The appliance does not start or stops during

operation.

If there is a fault, first try to find a solution to

the problem yourself. If you cannot find a sol-

ution to the problem yourself, contact the

Service Force Centre.

Caution! Switch off the appliance

before you do the below suggested

corrective actions.

12

Fault code and malfunction Possible cause and solution

• continuous flash of the light of the

running programme

• intermittent audible signal

• 1 flash of the end indicator light

The dishwasher does not fill with wa-

ter

• The water tap is blocked or furred with limescale.

Clean the water tap.

• The water tap is closed.

Open the water tap.

• The filter in the water inlet hose is blocked.

Clean the filter.

• The connection of the water inlet hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• continuous flash of the light of the

running programme

• intermittent audible signal

• 2 flashes of the end indicator light

The dishwasher will not drain

• There is a blockage in the sink spigot.

Clean the sink spigot.

• The connection of the water drain hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• the drain pump operates continu-

ously

• all indicators lights on the control

panel go off

The anti-flood device operates

• Close the water tap and contact your local Service Force

Centre.

The programme does not start • The appliance door is not closed.

Close the door.

• Mains plug is not connected in.

Put in the mains.

• The fuse has blown out in the household fuse box.

Replace the fuse.

• Delay start is set.

Cancel the delay start to start the programme immediately.

After the check, switch on the appliance. The

programme continues from the point of in-

terruption. If the malfunction shows again,

contact your Service Force Centre.

For other fault codes, not described in the

chart, contact your Service Force Centre.

These data are necessary to help you quickly

and correctly:

• Model (Mod.)

• Product number (PNC)

• Serial number (S.N.)

For these data, refer to the rating plate.

Write the necessary data here:

Model description : ..........

Product number : ..........

Serial number : ..........

The cleaning results are not satisfactory

The dishes are not clean • The selected washing programme is not applicable for the type of

load and soil.

• The basket is loaded incorrectly so that water cannot reach all sur-

faces.

• Spray arm does not turn freely because of incorrect arrangement of

the load.

• The filters are dirty or not correctly installed.

• The quantity of detergent is too little or missing.

Limescales particles on the

dishes

• The salt container is empty.

• The water softener is adjusted on a wrong level.

• The salt container cap is not closed correctly.

The dishes are wet and dull • No rinse aid has been used.

• The rinse aid dispenser is empty.

There are streaks, milky spots

or a bluish coating on glasses

and dishes

• Decrease the rinse aid dosage.

13

The cleaning results are not satisfactory

Dry water drop signs on

glasses and dishes

• Increase rinse aid dosage.

• The detergent can be the cause.

Technical data

Dimensions Width mm 450

Height mm 460

Depth mm 480

Water supply pressure Minimum 0,5 bar (0,05 MPa)

Maximum 8 bar (0,8 MPa)

Capacity Place settings 5

Information on the electrical connection, voltage and overall power is given on the rating

plate on the back of appliance.

Installation

Warning! Make sure that mains plug is

disconnected from the mains socket

during installation.

Fitting the appliance

Put the appliance adjacent to a water tap and

a drain.

When you put the appliance in place, make

sure that the water hoses are not kinked or

squashed.

Install the appliance on a kitchen sink, work-

top or built-in..

Positioning

Install the dishwasher into the furniture of the

kitchen.

Min. 465

Min. 455

Min. 485

Make sure that the dimensions of the recess

agree with the given dimensions.

Make sure that there are openings in the fur-

niture for the inlet hose, the water drain hose

and the mains cable.

Adjusting the level of the appliance

Make sure that the appliance is level to close

and seal the door correctly. If the level of the

appliance is correct, the door does not catch

on the sides of the cabinet. If the door does

not close correctly, loosen or tighten the ad-

justable feet until the appliance is level.

14

Water connection

Inlet hose

The appliance has safety features to prevent

that the water in the appliance goes back into

the drinking water system.

Connect the appliance to a hot (max. 60°) or

cold water supply.

If the hot water comes from alternative sour-

ces of energy that are more environmentally

friendly (e.g. solar or photovoltaic panels and

aeolian), use a hot water supply to decrease

energy consumption.

It is important that a water tap or stopcock is

near the dishwasher with easy access.

Connect the inlet hose to a water tap with an

external thread of 3/4”.

If the water inlet hose is too short, replace the

water inlet hose with an applicable, longer

high-pressure hose. Do not connect an ex-

tension hose.

To suit the installation, it is possible to turn

the end of the hose that is connected to the

dishwasher. Do these steps :

1. Loosen the retaining nut.

2. Turn the hose.

3. Tighten the retaining nut.

Warning! Make sure that the retaining

nut and all other connections are tight

before you move the dishwasher into

position.

Warning! Always use a new water inlet

hose. Do not use connection hoses from

an old appliance.

Drain hose

The appliance has water safety system to

prevent water damage. If there is a malfunc-

tion, the drain pump automatically starts to

drain the remaining water out of the dish-

washer.

Warning! Only if the dishwasher is

connected to the mains socket, the

water safety system operates when the

dishwasher is off.

2 procedures are possible to install the water

drain hose :

1. Attach the plastic curve supplied at the

end of the hose.

Put the water drain hose in the sink.

2. Connect the water drain hose to the wa-

ter drain system.

The hose must be less than 75 cm above

the bottom of the dishwasher to prevent

incorrect operation of appliance.

If you connect the water drain hose to a trap

spigot under the sink, remove the plastic

membrane (A). If you do not remove the

membrane, remaining food can cause a

blockage in the drain hose spigot

15

Electrical connection

Warning! The manufacturer is not

responsible if you do not follow these

safety precautions.

Ground the appliance according to safe-

ty precautions.

Make sure that the rated voltage and

type of power on the rating plate agree

with the voltage and the power of the lo-

cal power supply.

Always use a correctly installed shock-

proof socket.

Do not use multi-way plugs, connectors

and extension cables. There is a risk of

fire.

Do not replace the mains cable yourself.

Contact the Service Force Centre.

Make sure that the mains plug is acces-

sible after installation.

Do not pull the mains cable to discon-

nect the appliance. Always pull the

mains plug.

Environment concerns

The symbol on the product or on its

packaging indicates that this product may

not be treated as household waste. Instead

it should be taken to the appropriate

collection point for the recycling of electrical

and electronic equipment. By ensuring this

product is disposed of correctly, you will help

prevent potential negative consequences for

the environment and human health, which

could otherwise be caused by inappropriate

waste handling of this product. For more

detailed information about recycling of this

product, please contact your local council,

your household waste disposal service or the

shop where you purchased the product.

The packaging materials are environmentally

friendly and can be recycled. The plastic

components are identified by markings, e.g.

>PE<, >PS<, etc. Discard the packaging

materials in the applicable container at the

community waste disposal facilities.

Warning! To discard the appliance,

follow the procedure:

• Pull the mains plug out of the socket.

• Cut off the mains cable and mains

plug and discard them.

• Discard the door catch. This prevents

the children to close themselves in-

side the appliance and endanger their

lives.

16

Sommaire

Consignes de sécurité 17

Description de l'appareil 18

Bandeau de commande 19

Utilisation de l'appareil 21

Réglage de l'adoucisseur d'eau 21

Utilisation du sel régénérant 22

Utilisation du liquide de rinçage 22

Rangement des couverts et de la vaisselle

23

Utilisation du produit de lavage 24

Sélection et départ d'un programme de

lavage 25

Programmes de lavage 26

Entretien et nettoyage 27

En cas d'anomalie de fonctionnement

28

Caractéristiques techniques 29

Installation 29

Raccordement à l'arrivée d'eau 30

Branchement électrique 31

En matière de protection de

l'environnement 31

Sous réserve de modifications

Consignes de sécurité

Pour votre sécurité et le bon fonctionne-

ment de l'appareil, lisez attentivement ce

manuel avant l'installation et l'utilisation.

Conservez ces instructions à proximité

de l'appareil. Les utilisateurs doivent

connaître parfaitement le fonctionne-

ment et les fonctions de sécurité de l'ap-

pareil.

Utilisation réglementaire

• Cet appareil est exclusivement destiné à

un usage domestique.

• Ce lave-vaisselle est conçu pour laver la

vaisselle et les ustensiles de cuisine pou-

vant être lavés en machine.

• N'utilisez pas de solvants dans votre ap-

pareil. Ceux-ci pourraient provoquer une

explosion !

• Les couteaux et autres ustensiles pointus

ou tranchants doivent être placés dans le

panier à couverts avec la pointe vers le

bas, ou placez-les en position horizontale

dans le panier supérieur.

• N'utilisez que des produits (sel, produit de

lavage, liquide de rinçage) spécifiques

pour lave-vaisselle.

• Evitez d'ouvrir la porte pendant que l'ap-

pareil fonctionne : une vapeur brûlante

peut s'en échapper. Risque de brûlures !

• Ne sortez pas la vaisselle du lave-vaisselle

avant la fin du cycle de lavage.

• Lorsque le programme est terminé, dé-

branchez l'appareil et fermez le robinet

d'arrivée d'eau.

• Cet appareil ne peut être entretenu et ré-

paré que par un technicien autorisé, ex-

clusivement avec des pièces d'origine.

• N'essayez en aucun cas de réparer le lave-

vaisselle vous-même. Les réparations ef-

fectuées par du personnel non qualifié

peuvent provoquer des blessures ou le

mauvais fonctionnement du lave-vaisselle.

Contactez votre Service Après-vente. Exi-

gez des pièces d'origine.

Sécurité générale

• Les personnes (y compris les enfants) qui

souffrent de capacités mentales, physi-

ques et sensorielles réduites ou qui ne se

sont pas familiarisées avec le mode de

fonctionnement de l'appareil, ne doivent

pas l'utiliser. Elles doivent être surveillées

ou dirigées par une personne responsable

de leur sécurité.

• Respectez les consignes de sécurité du

fabricant du détergent pour éviter les brû-

lures aux yeux, à la bouche et la gorge.

• Ne buvez pas l'eau du lave-vaisselle. Des

résidus de produit de lavage peuvent res-

ter dans l'appareil.

• Fermez toujours la porte de l'appareil lors-

qu'il n'est pas utilisé pour empêcher tout

risque de blessure ou de chute acciden-

telle.

17

• Ne vous asseyez pas ou ne montez pas

sur la porte ouverte.

Sécurité enfants

• Seuls les adultes doivent utiliser cet appa-

reil. Veillez à ce que les enfants ne jouent

pas avec l'appareil.

• Rangez les emballages hors de la portée

des enfants. Ils présentent un risque de

suffocation.

• Rangez les détergents dans un endroit

sûr. Veillez à ce que les enfants ne tou-

chent pas les produits de lavage.

• Ne laissez pas les enfants s'approcher de

l'appareil quand la porte est ouverte.

Installation

• Vérifiez que l'appareil n'a pas été endom-

magé pendant le transport. Ne branchez

pas un appareil endommagé. Si nécessai-

re, contactez le fournisseur.

• Déballez l'appareil avant de l'utiliser pour

la première fois.

• Une personne compétente et qualifiée doit

prendre en charge l'installation électrique.

• Une personne compétente et qualifiée doit

prendre en charge le travail de plomberie.

• Ne modifiez ni les spécifications ni le pro-

duit. Risque de blessure ou d'endomma-

gement de l'appareil.

• N'utilisez pas l'appareil :

– si le câble secteur ou les tuyaux d'eau

sont endommagés,

– si le bandeau de commande, le plan de

travail ou la plinthe sont endommagés,

si vous pouvez accéder à l'intérieur de

l'appareil.

Contactez le service après-vente de votre

magasin vendeur.

• Ne percez pas dans les côtés de l'appareil

pour ne pas endommager les composants

électriques et hydrauliques.

Avertissement Respectez

scrupuleusement les consignes

données pour les branchements

électriques et le raccordement de l'eau.

Description de l'appareil

1

2

3

4

5

6

18

1 Distributeur de liquide de rinçage

2 Bras d'aspersion

3 Filtre fin

4 Distributeur de détergent

5 Filtre grossier

6 Réservoir de sel régénérant

L'étiquette des caractéristiques nomina-

les se trouve à l'arrière de l'appareil.

Bandeau de commande

1 2 3

4

AB

5

1 Touche Marche/Arrêt

2 Touche Départ différé / (Delay start)

3 Touche Sélection/Annulation du programme/ (Programme/ Cancel)

4 Voyants

5 Voyants du programme

Voyants

Programme en cours – s'allume quand vous sélectionnez un program-

me de lavage.

– reste allumé pendant toute la durée du pro-

gramme de lavage.

– s'éteint à la fin du programme.

19

Voyants

Sel

1)

s'allume lorsque le réservoir de sel régénérant doit

être rempli. Reportez-vous au chapitre " Utilisation

du sel régénérant ".

Le voyant de réapprovisionnement en sel régéné-

rant peut rester allumé plusieurs heures après le

remplissage du réservoir à sel. Cela n'affecte pas

le fonctionnement de l'appareil.

Fin s'allume quand le programme de lavage est ter-

miné. Fonctions auxiliaires :

• Niveau de l'adoucisseur.

• Activation/désactivation des signaux sonores.

• Une alarme se déclenche en cas d'anomalie de

fonctionnement.

1) Lorsque le réservoir à sel est vide, le voyant ne s'allume pas pendant qu'un programme est en cours.

Touche Sélection/Annulation du

programme

Appuyez sur la touche Sélection/Annulation

du programme pour :

• Sélectionner le programme de lavage. Re-

portez-vous au chapitre " Réglage et dé-

part d'un programme de lavage ".

• Régler l'adoucisseur d'eau. Reportez-

vous au chapitre " Réglage de l'adoucis-

seur d'eau ".

• Activer/désactiver les signaux sonores.

Reportez-vous au paragraphe "Signaux

sonores".

• Annuler un programme de lavage en

cours. Reportez-vous au chapitre " Régla-

ge et départ d'un programme de lavage ".

Touche Départ différé

Utilisez la touche Départ différé pour différer

l'heure de départ du programme de 3 heu-

res. Reportez-vous au chapitre "Réglage et

départ d'un programme de lavage".

Mode programmation

L'appareil est en mode programmation

quand tous les voyants des programmes

sont éteints et que le voyant de fin de pro-

gramme clignote.

L'appareil doit être en mode programmation

pour :

– Sélectionner un programme de lavage.

– Régler l'adoucisseur d'eau.

– Désactiver/activer les signaux sonores.

Si un voyant de programme est allumé, an-

nulez le programme pour revenir en mode

programmation. Reportez-vous au chapitre

"Réglage et départ d'un programme de la-

vage".

Voyants des programmes A et B

Mise à part l'indication de la sélection du pro-

gramme de lavage correspondant, ces voy-

ants ont des fonctions auxiliaires :

• Réglage du niveau de l'adoucisseur d'eau.

• Désactivation/activation des signaux so-

nores.

Signaux sonores

Un signal sonore peut retentir :

• À la fin du programme de lavage.

• En cas d'anomalie de fonctionnement de

l'appareil.

L'activation des signaux sonores est définie

en usine.

Pour désactiver les signaux sonores, procé-

dez comme suit :

1. Allumez l'appareil.

2. Vérifiez que l'appareil est en mode pro-

grammation.

3. Appuyez sur la touche de sélection/an-

nulation des programmes jusqu'à ce que

le voyant du programme A clignote et que

le voyant du programme B s'allume.

4. Appuyez à nouveau sur la touche de sé-

lection/annulation des programmes.

– Le voyant du programme A s'allume.

– Le voyant du programme B clignote.

5. Attendez que le voyant du programme A

s'éteigne.

– Le voyant du programme B continue à

clignoter.

– Le voyant de fin de programme s'allu-

me.

Les signaux sonores sont activés.

6. Appuyez à nouveau sur la touche de sé-

lection/annulation des programmes.

– Le voyant de fin de programme

s'éteint.

20

La page charge ...

Dometic DW2410 Manuel utilisateur

Dometic DW2410 Manuel utilisateur

dans d''autres langues

Autres documents