Maytag Dishwasher Mode d'emploi

Marque: Maytag

Modèle: Dishwasher

Catégorie: Lave-vaisselle

Taper: Mode d'emploi

Ce manuel convient également à

MDB8959SBW

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in

TROUBLESHOOTING, please visit our website at www.maytag.com for additional information. If you still need

assistance, call us at 1-800-688-9900. In Canada, visit our website at www.maytag.ca or

call us at 1-800-807-6777.

You will need your model and serial number located near the door on the right-hand or left-hand side of the

dishwasher interior.

Dishwasher Safety

DISHWASHER

USER INSTRUCTIONS

Table of Contents

DISHWASHER SAFETY ............................................................. 1

QUICK STEPS ............................................................................ 3

DISHWASHER USE.................................................................... 3

CYCLE AND OPTION DESCRIPTIONS.................................... 5

DISHWASHER FEEDBACK SECTION...................................... 7

DISHWASHER FEATURES........................................................ 8

DISHWASHER CARE................................................................. 9

TROUBLESHOOTING.............................................................. 10

WARRANTY .............................................................................. 12

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

W10596271A

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using the dishwasher, follow basic precautions, including the following:

SAVE THESE INSTRUCTIONS

■ Read all instructions before using the dishwasher.

■ Use the dishwasher only for its intended function.

■ Use only detergents or rinse agents recommended for use in

a dishwasher, and keep them out of the reach of children.

■ When loading items to be washed:

1) Locate sharp items so that they are not likely to damage

the door seal; and

2) Load sharp knives with the handles up to reduce the risk

of cut-type injuries.

■ Do not wash plastic items unless they are marked

“dishwasher safe” or the equivalent. For plastic items not so

marked, check the manufacturer's recommendations.

■ Do not touch the heating element during or immediately after

use.

■ Do not operate the dishwasher unless all enclosure panels

are properly in place.

■ Do not tamper with controls.

■ Do not abuse, sit on, or stand on the door, lid, or dish racks

of the dishwasher.

■ To reduce the risk of injury, do not allow children to play in

or on the dishwasher.

■ Under certain conditions, hydrogen gas may be produced in

a hot water system that has not been used for two weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using

the dishwasher turn on all hot water faucets and let the

water flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is flammable,

do not smoke or use an open flame during this time.

■ Remove the door or lid to the washing compartment

when removing an old dishwasher from service or

discarding it.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dishwasher:

The dishwasher must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for

electric current. The dishwasher is equipped with a cord

having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet

that is installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

if you are in doubt whether the dishwasher is properly

grounded. Do not modify the plug provided with the

dishwasher; if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

■

For a permanently connected dishwasher:

The dishwasher must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dishwasher.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Quick Steps

Dishwasher Use

Prepare and Load the Dishwasher

IMPORTANT: Remove leftover food, bones, toothpicks and other

hard items from the dishes. Remove labels from containers before

washing.

■ Make sure that when the dishwasher door is closed no items

are blocking the detergent dispenser.

■ Items should be loaded with soiled surfaces facing down and

inward to the spray as shown. This will improve cleaning and

drying results.

■ Avoid overlapping items like bowls or plates that may trap food.

■ Place plastics, small plates and glasses in the upper rack.

Wash only plastic items marked “dishwasher safe.”

■ To avoid thumping/clattering noises during operation: Load

dishes so they do not touch one another. Make sure lightweight

load items are secured in the racks.

Add Detergent

NOTE: If you do not plan to run a wash cycle soon, run a rinse

cycle. Do not use detergent.

■ Use automatic dishwasher detergent only. Add powder, liquid

or tablet detergent just before starting a cycle.

■ Fresh automatic

dishwasher

detergent results in

better cleaning.

Store tightly closed

detergent container

in a cool, dry place.

■ For optimum

performance, tablet

detergent is

recommended.

Prepare and load

dishwasher.

Select a cycle and option (cycles and options vary

by model.)

Add detergent

and rinse aid.

Start dishwasher.

STEP 1

Upper rack Lower rack

■ Make sure nothing keeps spray arm(s) from

spinning freely. It is important for the water

spray to reach all soiled surfaces.

■ When loading silverware, always place sharp

items pointing down. Mix other items

pointing up and some pointing down.

STEP 2

A. Cover latch

B. Main Wash section

C. Pre-Wash section

MAIN WASH

PRE-

WASH

Soft Water

Hard Water

Soft Water

Hard Water

Premeasured Detergents

Many detergents now come in premeasured forms (gel packs,

tablets, or powder packs). These forms are suitable for all hardness

and soil levels. Always place premeasured detergents in the main

compartment and close the lid.

Using dishwasher detergent tablets and packs have been proven

better than powder, liquid or gel detergents to reduce filming on

your dishes. By using these tablets and packs, over time this will

start to reduce or eliminate white film. Also, by using a rinse aid you

can minimize repeat buildup of white film.

Powder and Gels

■ The amount of detergent to use depends on:

How much soil remains on the items - Heavily soiled loads

require more detergent.

The hardness of the water - If you use too little in hard water,

dishes won't be clean. If you use too much in soft water,

glassware will etch.

Soft to Medium Water (0-6 grains per U.S. gallon)

[typical water softener water and some city water]

Medium to Hard Water (7-12 grains per U.S. gallon)

[well water and some city water]

■ Depending on your water hardness, fill the Main Wash section

of the dispenser as shown. Fill the Pre-Wash section to the

level shown, if needed.

NOTE: Fill amounts shown

are for standard powdered

detergent. Follow instructions

on the package when using

other dishwasher detergent.

Add Rinse Aid

■ Your dishwasher is designed to use rinse aid for good drying

performance. Without rinse aid your dishes and dishwasher

interior will have excessive moisture. The heat dry option will

not perform as well without rinse aid.

■ Rinse aid keeps water from forming droplets that can

dry as spots or streaks. They also improve drying by

allowing water to drain off of the dishes after the final

rinse.

■ Rinse aid helps to reduce excess moisture on the

dish racks and interior of your dishwasher.

■ Check the rinse aid indicator. Add rinse aid when indicator

drops to “Refill” level.

■ To add rinse aid, turn the

dispenser cap to “Open”

and lift off. Pour rinse aid

into the opening until the

indicator level is at “Full.”

Replace the dispenser cap

and turn to “Lock.” Make

sure cap is fully locked.

NOTE: For most water

conditions, the factory

setting of 2 will give good

results. If you have hard

water or notice rings or

spots, try a higher setting.

Turn the arrow adjuster

inside the dispenser by either

using your fingers or

inserting a flat-blade screwdriver into the center of the arrow and

turning.

Select a Cycle (cycles vary by model)

See “Cycle and Option Descriptions” charts in the following

section.Heavier cycles and options affect cycle length. Some

cycles and options will take up to 3¹⁄₂ hours to complete.

Select Options (options vary by model)

See “Cycle and Option Descriptions” charts in the following

section.

You can customize your cycles by pressing the options desired and

pressing Start/Resume.

Start or Resume a Cycle

■ Run hot water at the sink nearest your dishwasher until the

water is hot. Turn off water.

■ Push door firmly closed. The door latches

automatically. Select the wash cycle and options

desired and press START/RESUME OR press

START/RESUME to repeat the same cycle and

options as in the previous wash cycle.

■ You can add an item anytime before the main wash starts.

Open the door slowly and add the item. Close the door firmly.

Press the START/RESUME button, the cycle resumes

automatically at the point of interruption.

For fully integrated models (controls on top of console)

■ Select the wash cycle and options desired.

■ Press the START/RESUME button once and close the door.

After a brief pause, the cycle will begin. The door must be

closed within 3 seconds after pushing START/RESUME or the

lights will flash, and the dishwasher will not begin. Press the

START/RESUME button again and shut the door within

3seconds.

You can add an item anytime before the main wash starts. Open

the door slowly and add the item. Press the START/RESUME then

close the door.

Soft Water

Hard Water

Soft Water

Hard Water

Main Wash Pre-Wash

Full

Add

USE RINSE AID FOR

BETTER DRYING

Lock

Open

Full

Add

¹⁄₄ turn to lock

STEP 3

STEP 4

max

fill

Cycle and Option Descriptions

This information covers several different models. Your dishwasher may not have all of the cycles and options described.

Wash times depend on water temperature, heavy soil condition, dish load size and options selected. Adding options will add time to the

cycle.

*Adding options will add time to the cycle. See options information section.

**This is the approximate cycle time obtained with 120°F (49°C) hot water available at the dishwasher. Increase in time results from low

temperature of the incoming water.

CYCLE SELECTIONS

CYCLES SOIL LEVEL WASH TIME* (MINS.) WATER

USAGE

GALLONS

(Liters)

Typical**

W/O

Options

Max

This cycle senses the load size, soil amount, and

toughness of soil. This cycle is optimized to achieve the

best cleaning with minimal water and energy.

Light to Medium 90 250 4.2 (16.1)

Tough/Baked-

95 255 7.1 (26.7)

Heavy 95 255 7.1 (26.7)

This is the toughest cycle for your toughest food soils.

Use for hard-to-clean, heavily soiled pots, pans,

casseroles, and tableware.

Tough/Baked-

On/Heavy

135 295 12.7 (48.1)

This cycle is recommended to completely wash a full

load of normally soiled dishes. Selecting this cycle will

default to the options recommended for normal

amounts of food soil. The energy label is based on this

cycle.

Light to Medium 90 250 4.3 (16.2)

Heavy 90 250 7.1 (26.7)

Use for lightly soiled items. Light to Medium 70 115 4.2 (16.1)

For fast results, this cycle will clean your dishes using

more water and energy. For improved drying, select the

heated dry option.

Light to Medium 35 65 7.1 (26.7)

Use for rinsing dishes, glasses, and silverware that will

not be washed right away.

Do not use detergent. During the wash, the wash action

will repeatedly pause for several seconds.

All soil levels 20 20 1.8 (6.9)

OPTION SELECTIONS

OPTIONS dish load types DESCRIPTIONS USE WITH: ADDED

TIME TO

CYCLE

Tough food soils Adds heat and wash time to the cycle JetClean

Plus Steam, Normal,

and Auto Clean

30 min.

Tough food soils Increases the target water

temperature during the wash portions

of the cycle. Adds heat, time, and

water.

JetClean

Plus Steam, Normal,

and Auto Clean

5 min.

Tough food soils Increases the target water

temperature during the wash portions

of the cycle. Adds heat, time, and

water.

JetClean

Plus Steam, Normal,

and Auto Clean

10 min.

All loads Use for best drying results in

combination with rinse aid. Turn off

when loads contain plastic

dinnerware that may be sensitive to

higher temperatures.

JetClean

Plus Steam, Normal,

Light, Quick Wash and Auto Clean

45 min.

Loads requiring extra

drying

Use for best drying results in

combination with rinse aid. Turn off

when loads contain plastic

dinnerware that may be sensitive to

higher temperatures.

JetClean

Plus Steam, Normal,

Light, Quick Wash and Auto Clean

90 min.

To sanitize your dishes

and glassware

Raises the water temperature in the

final rinse to approximately 154°F

(68°C). This high temperature rinse

sanitizes your dishes and glassware

in accordance with NSF/ANSI

Standard 184 for Residential

Dishwashers. Certified residential

dishwashers are not intended for

licensed food establishments.The

Sanitize option adds heat and time to

the cycle.

JetClean

Plus Steam, Normal,

and Auto Clean

30 min.

All loads Delays the start of a cycle up to

8hours.

All cycles 2, 4, 8

hours

All loads When Control Lock is lit, all buttons

are disabled. If you press any pad

while your dishwasher is locked, the

light flashes. The door can be opened

while the controls are locked.

All cycles

Dishwasher Feedback Section

Canceling A Cycle

1. Open the door slightly to stop the cycle. Wait for the spraying

action to stop before completely opening the door.

2. Press CANCEL/DRAIN button once. The Cancel/Drain light will

light up.

3. Close the door and the dishwasher starts a drain cycle (if water

remains in bottom of dishwasher). Let the dishwasher drain

completely. The Cancel/Drain light turns off after 2 minutes.

Changing A Cycle After Dishwasher Is Started

1. You can interrupt a cycle and restart your dishwasher from the

beginning using the following procedure.

2. Open the door slightly to stop the cycle. Wait for the spraying

action to stop, then open the door completely.

3. Check that detergent dispenser cover is still closed. If cover is

open, you will need to refill the detergent dispenser before

restarting your new cycle.

4. Press CANCEL/DRAIN twice to reset the control.

5. Select new cycles and options.

6. Press START/RESUME.

Adding A Dish After Dishwasher Is Started

1. Check if Add a Dish indicator is lit. (Available on some models.

Otherwise, proceed to Step 2.)

2. Open the door slightly to stop the cycle. Wait for the spraying

action to stop, then open the door completely.

3. Check whether the detergent dispenser cover is still closed. If

it is open, the wash cycle has already started and adding a

dish is not recommended.

4. If detergent has not yet been used (detergent dispenser cover

is closed), you may add a dish.

5. Press START/RESUME.

CONTROLS AND CYCLE STATUS

CONTROL PURPOSE COMMENTS

To start or resume a

wash cycle

If the door is opened during a cycle or the power is interrupted, the START/RESUME

indicator flashes. The cycle will not resume until the door is closed and START/RESUME is

pressed.

NOTE: If the START/RESUME button is located on top of door, push door firmly closed

within 3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds,

the start button LED will flash, an audible tone will be heard, and the cycle will not start.

To reset any cycle or

options during

selection.

To cancel a wash

cycle after it's

started.

Press CANCEL/DRAIN to reset any control selections made.

See “Canceling A Cycle” and “Changing A Cycle After Dishwasher Is Started” sections.

To turn the audible

tones on or off.

Press and hold the Hi Temp Wash button for 3 seconds to turn the audible tones on or off.

Only audible tones for confirming button presses can be turned on/off. Important audible

tones, such as indicating a cycle has been interrupted, cannot be deactivated.

NOTE: Audible tones are not available on all models.

CONTROLS AND CYCLE STATUS

CONTROL PURPOSE COMMENTS

The Cycle Status Indicator

Lights are used to follow the

progress of the dishwasher

cycle. Located on the front

of the dishwasher for front

control models, and located

on the top of the door for

hidden control models.

Clean indicator glows when a cycle is finished.

If you select the Sani Rinse option, when the Sani Rinse cycle is finished,

the Sanitized indicator glows. If your dishwasher did not properly sanitize

your dishes, the light flashes at the end of the cycle. This can happen if the

cycle is interrupted, or the water could not be heated to the required

temperature.

The Clean and Sanitized lights go off when you open and close the door or

press CANCEL.

Dishwasher Features

Your Maytag dishwasher may have some or all of these features.

Split & Fit™ Utensil Basket

The split silverware basket can be

separated and placed in various

locations in the lower rack. Load

flatware and utensils into both

sections or just one, depending on

your load.

To split the basket:

Hold the basket firmly along the sides.

Unlock the baskets.

Silverware basket lids:

Use silverware basket lids to provide

optimal spacing and best cleaning

performance.

Utensil Basket

Use the utensil basket to hold specialty

cooking utensils (serving spoons,

spatulas, and similar items), or overflow

silverware items.

The basket hangs on the bottom rack in

the right-hand corner. Load the basket

while it is on the bottom rack or remove

the basket for loading on a counter or

table.

NOTE: Spin the spray arms. Be sure

items in the basket do not stop the

rotation of the spray arms.

Folding Tines

The Folding Tines located in the front

right corner (lower rack) provide

convenient loading space for large,

bulky items such as pots, pans and

mixing bowls.

To lower the tines:

Gently push the tines out of each holder

toward the center rack and lay the tines

down.

Cup Clips

The Cup Clips located in the center of the upper

rack can be used to hold lightweight plastic items,

cooking utensils and knives in place. Clip the item

between the tine and the clip.

Stack-Rack Shelves

Increase loading flexibility - items

like casserole dishes stay stable

while the folding shelf allows you to

load smaller items on top.

Cup Shelf

Fold down the extra shelf on the left-hand or

right-hand side of the top rack to hold

additional cups, stemware, or long items

such as utensils and spatulas.

Adjustable Upper Racks

The Adjustable Upper Rack and can be raised or lowered to

accommodate taller plates, platters, pots or pans, in the upper or

lower racks. Full size dinner plates can be loaded in the upper rack

if it is in the lower position.

NOTE: Always unload racks before adjusting.

To raise the rack, press both

rack adjusters and lift the rack

until it is in the Up position

and level.

To lower the rack, press both

rack adjusters and slide the

rack back to its lower

position.

Manual Adjustable 2-Position Top Rack

You can raise or

lower the top

rack to fit tall

items in either the

top or bottom

rack. Adjusters

are located on

each side of the

top rack. Raise

the top rack to

accommodate

items up to 9"

(22 cm) in the top rack and 13" (33 cm) in the bottom rack, or lower

the top rack to accommodate items up to 11" (28 cm) in both the

top and bottom racks.

IMPORTANT: Remove dishes prior to removing the top rack from

the dishwasher.

To raise, remove rack and slide lower wheels into the rails as

directed in “Removable Top Rack” section.

To lower, remove rack and slide upper wheels into the rails as

directed in “Removable Top Rack” section.

Removable Upper Rack

The removable rack allows you to wash larger items such as stock

pots, roasters, and cookie sheets in the lower level rack.

IMPORTANT: Remove dishes prior to removing the upper rack

from the dishwasher.

To remove the rack (push tab rack stop):

1. Roll the rack ¹⁄₃ to ¹⁄₂ of the way out.

2. Remove each plastic push tab rack stop

from the end of each track by pushing

inward toward the rack on the ridged area

of the rack stop. The rack stop will snap

open and can be easily removed by

pulling straight out. Be sure to support the

track while removing rack stops.

3. Roll the rack all the way out of the track and remove from the

dishwasher.

To replace the rack:

Reverse the above steps 1-3 to replace the rack into the

dishwasher.

Dishwasher Care

CLEANING THE DISHWASHER

Cleaning the exterior

Clean the exterior of the dishwasher with a soft, damp cloth and

mild detergent. If your dishwasher has a stainless steel exterior, a

stainless steel cleaner is recommended - Stainless Steel Cleaner

and Polish Part Number 31464.

Cleaning the interior

Clean the interior of the dishwasher, with a paste of powdered

dishwasher detergent and water or use liquid dishwasher detergent

on a damp sponge to clean the cooled-down interior.

A white vinegar rinse may remove white spots and film. Vinegar is

an acid, and using it too often could damage your dishwasher.

Put 2 cups (500 mL) white vinegar in a glass or dishwasher-safe

measuring cup on the bottom rack. Run the dishwasher through a

complete washing cycle using an air-dry or an energy-saving dry

option. Do not use detergent. Vinegar will mix with the wash water.

Dishwasher Maintenance Procedure

Removal of Hard Water / Filming: Recommended use of a

monthly maintenance product such as affresh

®†

Dishwasher

Cleaner Part Number W10282479.

■ Load your dishwasher (preferably with dishes affected by

filming/hard water).

■ Place tablet in main wash compartment of detergent dispenser.

■ Select cycle/option best for heavily soiled dishes and start

dishwasher.

NOTE: Recommended to use a premeasured detergent tablet or

pack for regular daily use.

Drain air gap

To Reduce Risk of Property Damage During Vacation or

Extended Time Without Use

■ When you will not be using the dishwasher during the summer

months, turn off the water and power supply to the dishwasher.

■ Make sure the water supply lines are protected against freezing

conditions. Ice formations in the supply lines can increase

water pressure and cause damage to your dishwasher or

home. Damage from freezing is not covered by the warranty.

■ When storing your dishwasher in the winter, avoid water

damage by having your dishwasher winterized by authorized

service personnel.

†® affresh is a registered trademark of Whirlpool, U.S.A.

If you have a drain air gap,

check and clean it if the

dishwasher isn't draining

well.

Troubleshooting

First try the solutions suggested here or visit our website and reference FAQs

(Frequently Asked Questions) to possibly avoid the cost of a service call.

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

PROBLEM SOLUTION

DISHWASHER DOES

NOT RUN

NOTE: It is normal for the dishwasher to repeatedly pause several times during a cycle.

If the START/RESUME light is blinking, press START/RESUME and close the door firmly within

3seconds.

Press and hold HI TEMP WASH for 3 seconds to turn the audible tones on or off.

Be sure the door is closed and latched.

Be sure you have selected a cycle. (See “Cycles and Options Descriptions.”)

Be sure there is power to the dishwasher. A circuit breaker or fuse might have tripped.

If lights other than START/RESUME blink and the unit will not run, you will need to call for service.

DETERGENT REMAINS IN THE

DISPENSER OR

TABLET IS ON BOTTOM

OF TUB

Check for dishware such as cookie sheets, cutting boards, or large containers, etc., that may be

blocking the detergent dispenser from opening properly.

Be sure your detergent is fresh and lump free.

Be sure the cycle has been completed (green light is on). If it has not been completed, you will need

to resume the cycle by pressing START/RESUME and closing the door within 3 seconds.

CYCLE RUNS TOO LONG NOTES:

■ To use less water and reduce energy consumption you will encounter cycles that typically run

for up to 3 hours.

■ A water heater setting of 120°F (49ºC) is best. The dishwasher will delay longer while heating

cooler water.

■ Some options will add time to the cycle. (See “Cycles and Options Descriptions” section.) The

Heated Dry option adds ½ hour.

Try the Quick Wash cycle.

Run the hot water at a faucet close to the dishwasher before starting the cycle.

DISHWASHER NOT DRYING NOTE: Plastic and items with nonstick surfaces are difficult to dry because they have a porous

surface which tends to collect water droplets. Towel drying may be necessary.

Use of rinse aid along with the Heated Dry option is needed for proper drying.

Proper loading of items can affect drying. (See specific loading instructions within this guide.)

Glasses and cups with concave bottoms hold water. This water may spill onto other items when

unloading.

■ Unload the bottom rack first.

■ Locate these items on the more slanted side of the rack for improved results.

WILL NOT FILL Be sure the water is turned on to the dishwasher.

Check that the float is free from obstructions. (See “Parts and Features.”)

Check for suds in the dishwasher. If foam or suds are detected, the dishwasher

may not operate properly or may not fill with water.

WATER REMAINS IN THE TUB/

WILL NOT DRAIN

Be sure the cycle has been completed (the green light is on). If the cycle has not been completed,

you will need to resume the cycle by pressing START/RESUME and closing the door within

3 seconds.

If dishwasher is connected to a food waste disposer, be sure the knockout plug has been removed

from the disposer inlet.

Check for kinks in the drain hose.

Check for food obstructions in the drain or disposer.

Check your house fuse or circuit breaker.

HARD WATER

(WHITE RESIDUE ON

DISHWASHER INTERIOR OR

GLASSWARE)

NOTE: Extremely hard water mineral deposits can cause damage to your dishwasher and make it

difficult to achieve good cleaning. A water softener is strongly recommended if your hardness is

15 grains or more. If a water softener is not installed, the following steps may help:

Use a commercial cleaner designed for dishwashers once per month.

Always use a rinse aid.

Always use a high-quality, fresh detergent.

Use a detergent booster/water softener additive designed for dishwashers.

ODORS NOTE: If the dishwasher is not used daily, you can run a rinse cycle with the partial load until a full

load is ready to run.

Run a vinegar rinse through the dishwasher by putting 2 cups (500 mL) of white vinegar in an

upright glass measuring cup in the lower rack. Run a normal cycle with the Heated Dry option

turned off. Do not use detergent.

The dishwasher may not be draining properly, see “WATER REMAINS IN THE TUB/WILL NOT

DRAIN” in “Troubleshooting.”

NOISY NOTES:

■ Surging sounds can occur periodically throughout the cycle while the dishwasher is draining.

■ Normal water valve hissing may be heard periodically.

■ A normal snap sound may be heard when the detergent dispenser opens during the cycle and

when the door is opened at the end of the cycle.

■ Improper installation will affect noise levels.

■ Be sure the filters are properly installed.

■ A thumping sound may be heard if items extend beyond the racks and interfere with the wash

arms. Readjust the dishware and resume the cycle.

FOOD SOILS REMAIN

ON DISHES

Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing

performance (see “Prepare and Load the Dishwasher”).

Select the proper cycle and option for the type of soils. The JetClean

/JetClean

Plus Steam cycle

with the Steam Sanitize option can be used for tougher loads.

Be sure the incoming water temperature is at least 120°F (49ºC).

Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads and

hard water conditions.

Scrape food from dishes prior to loading (do not prerinse).

DID NOT SANITIZE If the sanitized light is blinking, the load is NOT sanitized. The cycle was interrupted in the final

rinse, or your water heater is set too low. Set your water heater to 120ºF (49ºC).

DAMAGE TO DISHWARE Improper loading can cause dishes to become chipped or damaged. (See specific loading

instructions within this guide.)

BLINKING LIGHTS If the START/RESUME light is blinking, press START/RESUME and close the door within 3 seconds.

If the Clean light or any other lights are blinking and the dishwasher will not run, call for service.

CLOUDY OR SPOTTED

DISHWARE (AND HARD

WATER SOLUTION)

NOTES:

■ Liquid rinse aid is necessary for drying and to reduce spotting.

■ Use the correct amount of detergent.

Confirm that the cloudiness is removable by soaking the item in white vinegar for 5 minutes. If the

cloudiness disappears, it is due to hard water. Adjust the amount of detergent and rinse aid. See

(“HARD WATER [WHITE RESIDUE ON DISHWASHER INTERIOR OR GLASSWARE]”) in

“Troubleshooting.” If it does not come clear, it is due to etching (see below).

Be sure the incoming water temperature is set at 120°F (49ºC).

Try using the Hi Temp and Sani Rinse options.

To remove spotting, run a vinegar rinse through the dishwasher.

■ Wash and rinse the affected dishware and load into dishwasher. Remove all silverware and

metal items. Put 2 cups (500 mL) of white vinegar in a glass measuring cup in the lower rack.

Run a normal cycle with the Heated Dry option turned off. No detergent is needed.

ETCHING (PERMANENT

CLOUDINESS)

This is an erosion of the surface of the glassware and can be caused by a combination of: water

that is too hot, from using too much detergent with soft water or by pre-washing. Detergent needs

food soil to act upon. If etching has occurred, the glassware is permanently damaged. To avoid

further etching, adjust the detergent amount to match the water hardness, stop pre-washing, and

use water heating options only when incoming water temperature is below 120°F (49ºC).

LEAKING WATER Be sure dishwasher has been installed properly and is level.

Suds can cause the dishwasher to overflow. Measure the detergent accurately and use only

detergents designed for use in a dishwasher. Less detergent is needed in soft water. Try another

brand of detergent if sudsing continues.

To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached and avoid

overfilling.

TUB IS DISCOLORED NOTES:

■ High iron content in the water can discolor the tub.

■ Tomato-based foods can discolor the tub or dishware.

A citrus-based cleaner can be used to clean.

PROBLEM SOLUTION

MAYTAG

DISHWASHER LIMITED WARRANTY

FIRST YEAR LIMITED WARRANTY (PARTS AND LABOR)

For one year from the date of purchase, when this major appliance is installed, operated and maintained according to instructions

attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada, LP (hereafter “Maytag”) will pay

for factory specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this major

appliance was purchased.

SECOND THROUGH TENTH YEAR LIMITED WARRANTY (CERTAIN COMPONENT PARTS ONLY - LABOR NOT INCLUDED)

In the second through tenth years from the date of original purchase, when this major appliance is installed, operated and maintained

according to instructions attached to or furnished with the product, Maytag will pay for factory specified parts for the following

components to correct non-cosmetic defects in materials or workmanship in these parts that prevent function of the dishwasher and that

existed when this major appliance was purchased. This is a limited 10-year warranty on the below named parts only and does not include

repair labor.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THE LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a Maytag designated service company. This limited warranty is valid in the United States or Canada and

applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the date of

the original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used

in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair

house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance

with electrical or plumbing codes, or use of products not approved by Maytag.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.

6. Pickup and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Maytag servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with

Maytag published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot

be easily determined.

11. Discoloration, rust, or oxidation of stainless steel surfaces.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do

not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty

gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.

If you think you need repair service, first see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the

problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by calling

Maytag. In the U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777.

7/12

■ Upper and Lower Racks (excludes cup shelf and silverware basket)

■ Chopper Blade

■ Stainless Steel Tub and Inner Door Liner

For additional product information, in the U.S.A., visit www.maytag.com

In Canada, visit www.maytag.ca

If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may

contact Maytag at the number below.

Have your complete model number ready. You can find your model number and serial number on the label located near the door on the

right-hand or left-hand side of the dishwasher interior.

For assistance or service in the U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777.

If you need further assistance, you can write to Maytag with any questions or concerns at the address below:

In the U.S.A.:

Maytag Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

In Canada:

Maytag Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Please keep this User Instructions and model number information for future reference.

W10596271A

5/13

Printed in U.S.A.

LE AGRADECEMOS la compra de este producto de alta calidad. Si usted experimenta un problema que no se haya

cubierto en SOLUCIÓN DE PROBLEMAS, visite nuestro sitio de internet en www.maytag.com para obtener

información adicional. Si considera que aún necesita ayuda, llámenos al 1-800-688-9900. En Canadá, visite nuestro

sitio de internet en www.maytag.ca o llámenos al 1-800-807-6777.

Necesitará tener a mano el número de modelo y de serie, que está ubicado cerca de la puerta, del lado derecho o

izquierdo del interior de la lavavajillas.

Seguridad de la lavavajillas

INSTRUCCIONES PARA USUARIO

DE LA LAVAVAJILLAS

Índice

SEGURIDAD DE LA LAVAVAJILLAS ..................................... 14

PASOS RÁPIDOS ..................................................................... 16

USO DE LA LAVAVAJILLAS.................................................... 16

DESCRIPCIÓN DE CICLOS Y OPCIONES............................. 18

SECCIÓN DE INFORMACIÓN PROVISTA

POR LA LAVAVAJILLAS.......................................................... 20

CARACTERÍSTICAS DE LA LAVAVAJILLAS ......................... 21

CUIDADO DE LA LAVAVAJILLAS........................................... 22

SOLUCIÓN DE PROBLEMAS ................................................. 23

GARANTÍA ................................................................................ 26

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesión grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesión grave.

Todos los mensajes de seguridad le dirán el peligro potencial, le dirán cómo reducir las posibilidades de sufrir una lesión y lo que

puede suceder si no se siguen las instrucciones.

Su seguridad y la seguridad de los demás es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual y en su electrodoméstico. Lea y obedezca siempre

todos los mensajes de seguridad.

ADVERTENCIA

PELIGRO

Este es el símbolo de advertencia de seguridad.

Este símbolo le llama la atención sobre peligros potenciales que pueden ocasionar la muerte o una lesión a

usted y a los demás.

Todos los mensajes de seguridad irán a continuación del símbolo de advertencia de seguridad y de la palabra

“PELIGRO” o “ADVERTENCIA”. Estas palabras significan:

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENCIA: Cuando use la lavavajillas siga precauciones básicas, incluyendo las siguientes:

GUARDE ESTAS INSTRUCCIONES

■ Lea todas las instrucciones antes de usar la lavavajillas.

■ Use la lavavajillas únicamente para las funciones que fue

diseñada.

■ Use únicamente detergentes o agentes de enjuague

recomendados para ser usados en las lavavajillas y

manténgalos fuera del alcance de los niños.

■ Al introducir los artículos para lavar:

1) Coloque los artículos puntiagudos de manera que no

dañen el sello de la puerta

2) Introduzca los cuchillos filosos con los mangos hacia

arriba para reducir el riesgo de cortaduras.

■ No lave artículos de plástico que no lleven la indicación

“lavables en la lavavajillas” u otra similar. Lea las

recomendaciones del fabricante para los artículos de

plástico que no lleven tal indicación.

■ No toque el elemento de calefacción durante o

inmediatamente después de usar la lavavajillas.

■ No haga funcionar la lavavajillas a menos que todos los

paneles estén colocados debidamente en su lugar.

■ No juegue con los controles.

■ No abuse, ni se siente ni se pare sobre la puerta, la tapa o

sobre las canastas de la lavavajillas.

■ Para reducir el riesgo de lesión, no permita que los niños

jueguen dentro ni sobre la lavavajillas.

■ Bajo ciertas condiciones, un sistema de agua caliente que

no ha sido usado por dos semanas o más puede producir

gas hidrógeno. EL GAS HIDRÓGENO ES EXPLOSIVO. Si

el sistema de agua caliente no ha sido usado por ese

período, abra todas las llaves de agua caliente y deje que

corra el agua por varios minutos antes de usar la

lavavajillas. Esto permitirá que los gases acumulados

escapen. Debido a que el gas es inflamable, no fume ni

encienda ninguna llama abierta durante este tiempo.

■ Quite la puerta o la tapa del compartimiento de lavado

cuando remueva o deje de usar para siempre una vieja

lavavajillas.

INSTRUCCIONES DE CONEXIÓN A TIERRA

GUARDE ESTAS INSTRUCCIONES

■

Para una lavavajillas con cable eléctrico y conexión a

tierra:

La lavavajillas debe estar conectada a tierra. En caso de

funcionamiento defectuoso o avería, la conexión a tierra

reduce el riesgo de choque eléctrico al establecer una ruta

de menor resistencia para la corriente eléctrica. La

lavavajillas viene equipada con un cable eléctrico que tiene

un conductor para conexión a tierra y un enchufe con

conexión a tierra. El enchufe debe ser conectado a un

contacto apropiado que esté instalado y conectado a tierra

de acuerdo con todos los códigos y ordenanzas locales.

ADVERTENCIA:

La conexión inadecuada del

conductor de conexión a tierra puede resultar en riesgo

de choque eléctrico. Pregunte a un electricista

calificado o a un agente de servicio si no está seguro si

la lavavajillas está adecuadamente conectada a tierra.

No modifique el enchufe que viene con la lavavajillas. Si

no cabe en el contacto, pida que un electricista

calificado instale un contacto apropiado.

■

Para lavavajillas con conexión permanente:

Esta lavavajillas debe estar conectada a un sistema de

cableado de metal permanente, conectado a tierra, o se

debe tender un conducto para la conexión a tierra del

equipo con los conductores de circuito y conectado a la

terminal de tierra del equipo o al conductor de

suministro de la lavavajillas.

Peligro de Vuelco

No use la lavavajillas antes de estar completamente instalada.

No se apoye en la puerta abierta.

No seguir estas instrucciones puede ocasionar heridas serias o cortaduras.

ADVERTENCIA

Advertencias de la Proposición 65 del estado de California:

ADVERTENCIA: Este producto contiene una o más sustancias químicas identificadas por el estado de California como

causantes de cáncer.

ADVERTENCIA: Este producto contiene una o más sustancias químicas identificadas por el estado de California como

causantes de defectos congénitos o algún otro tipo de daños en la función reproductora.

Pasos rápidos

Uso de la lavavajillas

Prepare y cargue la lavavajillas

IMPORTANTE: Quite los restos de alimentos, huesos, palillos y

otros artículos duros de los platos. Quite las etiquetas de los

recipientes antes de lavarlos.

■ Asegúrese de que cuando esté cerrada la puerta de la

lavavajillas no haya artículos bloqueando el depósito de

detergente.

■ Los artículos deberán cargarse con las superficies sucias

mirando hacia abajo y hacia adentro, hacia el rociador, como

se muestra. Esto mejorará los resultados de limpieza y de

secado.

■ Evite superponer los artículos como tazones o platos, que

pueden atrapar la comida.

■ Coloque los plásticos, platos pequeños y vasos en la canasta

superior. Lave sólo artículos de plástico marcados como

“lavable en la lavavajillas”.

■ Para evitar ruidos descomunales o estrepitosos durante el

funcionamiento: Coloque los platos de manera que no se

toquen entre sí. Asegúrese de que los objetos livianos estén

firmes en las canastas.

Agregue detergente

NOTA: Si no va a hacer funcionar un ciclo de lavado de inmediato,

ponga un ciclo de enjuague. No use detergente.

■ Use únicamente detergentes para lavavajillas automáticas.

Agregue detergente en polvo, líquido o en pastilla justo antes

de comenzar un ciclo.

■ El detergente para

lavavajillas

automáticas

produce mejores

resultados cuando

está fresco. Guarde

el detergente bien

cerrado en un lugar

fresco y seco.

■ Para un

rendimiento

óptimo, se

recomienda

detergente en

tableta.

Prepare y cargue

la lavavajillas.

Seleccione un ciclo y una opción (los ciclos y las

opciones varían según el modelo).

Agregue el

detergente y el

agente de

enjuague.

Ponga la

lavavajillas en

marcha.

PASO 1

Canasta superior Canasta inferior

■ Asegúrese de que nada impida que el (los)

brazo(s) rociador(es) gire(n) libremente. Es

importante que el rociado de agua alcance

todas las superficies sucias.

■ Cuando cargue la canastilla de los cubiertos,

coloque siempre los artículos filosos

apuntando hacia abajo. Mezcle otros

artículos con la punta hacia arriba y algunos

con la punta hacia abajo.

PASO 2

MAIN WASH

PRE-

WASH

Soft Water

Hard Water

Soft Water

Hard Water

A. Seguro de la tapa

B. Sección de lavado

principal

C. Sección de prelavado

Detergentes previamente medidos

Varios detergentes vienen ahora en formatos previamente medidos

(paquetes con gel, tabletas o paquetes con polvo). Estos formatos

son apropiados para todos los niveles de dureza y suciedad.

Coloque siempre los detergentes previamente medidos en el

compartimiento principal y cierre la tapa.

Está comprobado que las pastillas y los paquetes de detergente

para lavavajillas son más eficaces que los detergentes en polvo,

líquidos o en gel, para reducir las películas de residuos en la vajilla.

Al usar estas pastillas y paquetes, con el tiempo las películas

blancas comenzarán a reducirse o a eliminarse. Por otro lado, al

usar un agente de enjuague puede minimizar la acumulación

repetida de películas blancas.

Polvos y geles

■ La cantidad de detergente a usar depende de:

Cuánta suciedad permanece en los artículos - Las cargas con

suciedad profunda requieren más detergente.

La dureza del agua - Si usa muy poco en agua dura, los platos

no quedarán limpios. Si usa demasiado en agua blanda,

ocurrirá corrosión en las piezas de cristal.

Agua suave a medio dura (0-6 granos por galón de

EE.UU.)

[agua típica tratada con ablandador de agua y cierto tipo

de agua urbana]

Agua medio dura a dura (7 a 12 granos por galón de

EE.UU.)

[agua de pozo y cierto tipo de agua urbana]

■ Según la dureza del agua, llene la sección de Main Wash

(Lavado principal) del depósito, como se muestra. Llene la

sección de Pre-Wash (Prelavado) hasta el nivel mostrado, si es

necesario.

NOTA: Las cantidades de

llenado que se indican

corresponden a los

detergentes en polvo

estándares. Siga las

instrucciones del paquete

cuando use otro detergente para lavavajillas.

Agregue el agente de enjuague

■ Para obtener un buen secado, su lavavajillas ha sido diseñada

para usar un agente de enjuague. Si no usa agente de

enjuague, los platos y el interior de la lavavajillas tendrán

demasiada humedad. La opción de secado con calor no

funcionará tan bien sin usar el agente de enjuague.

■ Los agentes de enjuague evitan que el agua forme

gotitas que pueden secarse como manchas o rayas.

Asimismo mejoran el secado pues permiten que el

agua se escurra de los platos después del enjuague

final.

■ El agente de enjuague ayuda a reducir el exceso de

humedad sobre las canastas de los platos y el interior

de la lavavajillas.

■ Revise el indicador del agente de enjuague. Agregue el agente

de enjuague cuando el indicador baje hasta el nivel “Refill”

(Volver a llenar).

■ Para agregar agente de

enjuague, gire la tapa del

depósito hacia “Open”

(Abrir) y quítela. Vierta el

agente de enjuague en la

abertura hasta que el

indicador esté en “Full”

(Lleno). Vuelva a colocar la

tapa del depósito y gírela

hacia “Lock” (Seguro).

Asegúrese de que la tapa

esté asegurada por

completo.

NOTA: Para casi todos los

tipos de agua, la selección

de fábrica de 2 dará buenos

resultados. Si tiene agua

dura o nota que hay aros o

manchas, pruebe con un

ajuste más alto. Gire el ajuste

de flecha que se encuentra

dentro del depósito usando

sus dedos o insertando un destornillador de hoja plana en el centro

de la flecha y haciéndola girar.

Seleccione un ciclo (los ciclos varían según el modelo)

Vea las tablas de “Descripcion de ciclos y opciones” en la sección

siguiente.

Los ciclos y las opciones más intensos afectarán la duración del

ciclo. Algunos ciclos y opciones demorarán hasta 3¹⁄₂ horas en

completarse.

Seleccione las opciones (las opciones varían según el

modelo)

Vea las tablas de “Descripcion de ciclos y opciones” en la sección

siguiente.

Usted puede personalizar sus ciclos oprimiendo las opciones

deseadas y luego Start/Resume (Inicio/Reanudar).

Inicio o reanudación de un ciclo

■ Deje correr agua caliente en el fregadero que esté más cerca

de su lavavajillas hasta que el agua salga caliente. Cierre la

llave del agua.

■ Empuje la puerta cerrándola con firmeza. La puerta

queda asegurada automáticamente. Seleccione el

ciclo y las opciones de lavado deseados y presione

START/RESUME (Inicio/Reanudar) O BIEN

presione START/RESUME (Inicio/Reanudar) para

repetir el mismo ciclo y opciones que en el ciclo anterior de

lavado.

■ Usted puede agregar un artículo en cualquier momento antes

de que comience el lavado principal. Abra lentamente la puerta

y agregue el artículo. Cierre la puerta con firmeza. Presione el

botón de START/RESUME (Inicio/Reanudar). El ciclo se

reanuda automáticamente en el momento en que fue

interrumpido.

Para modelos completamente incorporados (controles

en la parte superior de la consola)

■ Seleccione el ciclo de lavado y opciones que desee.

■ Presione una vez el botón de START/RESUME (Inicio/

Reanudar) y cierre la puerta. El ciclo comenzará después de

una breve pausa. Deberá cerrarse la puerta en menos de

3 segundos después de presionar START/RESUME (Inicio/

Reanudar) o las luces destellarán y la lavavajillas no comenzará

a funcionar. Presione nuevamente el botón de START/RESUME

(Inicio/Reanudar) y cierre la puerta en menos de 3 segundos.

Usted puede agregar un artículo en cualquier momento antes de

que comience el lavado principal. Abra lentamente la puerta y

agregue el artículo. Presione el botón de START/RESUME (Inicio/

Reanudar) y cierre la puerta.

Soft Water

Hard Water

Soft Water

Hard Water

Lavado principal Prelavado

Full

Add

USE RINSE AID FOR

BETTER DRYING

Lock

Open

Full

Add

¹⁄₄

de giro para asegurar

PASO 3

PASO 4

max

fill

Descripción de ciclos y opciones

Esta información cubre varios modelos diferentes. Puede ser que su lavavajillas no cuente con todos los ciclos y opciones descritos.

Los tiempos de lavado dependen de la temperatura del agua, condición de suciedad profunda, tamaño de la carga de vajilla y opciones

seleccionadas. El agregar opciones aumentará el tiempo del ciclo.

* El agregar opciones aumentará el tiempo del ciclo. Vea la sección de información sobre las opciones.

** Este es el tiempo aproximado del ciclo que se obtiene con agua caliente a 120°F (49°C) entrando en la lavavajillas. La baja temperatura

del agua entrante genera un aumento del tiempo.

SELECCIONES DE CICLO

CICLOS NIVEL DE

SUCIEDAD

TIEMPO DE LAVADO*

(MIN.)

USO DE

AGUA EN

GALONES

(Litros)

Típico**

Sin

opciones

Máx.

Este ciclo detecta el tamaño de la carga, la cantidad de

suciedad y su resistencia. Este ciclo ha sido

optimizado para lograr la mejor limpieza con una

mínima cantidad de agua y consumo de energía.

Ligera a media 90 250 4,2 (16,1)

Rebelde/

Endurecida por

el horneado

95 255 7,1 (26,7)

Intensa 95 255 7,1 (26,7)

Éste es el ciclo más potente para la suciedad más

rebelde. Use este ciclo para ollas, sartenes, cacerolas y

vajilla común muy sucias que sean difíciles de lavar.

Rebelde/

Endurecida por

el horneado/

Intensa

135 295 12,7 (48,1)

Se recomienda este ciclo para lavar por completo una

carga llena de vajilla con suciedad normal. Al

seleccionar este ciclo, se fijarán por defecto las

opciones recomendadas para cantidades normales de

suciedad. La etiqueta de energía está basada en este

ciclo.

Ligera a media 90 250 4,3 (16,2)

Intensa 90 250 7,1 (26,7)

Úselo para artículos con suciedad ligera. Ligera a media 70 115 4,2 (16,1)

Para obtener resultados rápidos, este ciclo limpiará la

vajilla usando más agua y energía. Para mejorar el

secado, seleccione la opción de secado con calor.

Ligera a media 35 65 7,1 (26,7)

Use este ciclo para enjuagar platos, vasos y cubiertos

que no vayan a lavarse de inmediato.

No use detergente. Durante el lavado, la acción de

lavado hará pausas repetidamente por varios

segundos.

Todos los

niveles de

suciedad

20 20 1,8 (6,9)

SELECCIONES DE OPCIONES

OPCIONES tipos de carga de

platos

DESCRIPCIONES USAR CON: TIEMPO

AGREGA-

DO AL

CICLO

Suciedad rebelde de los

alimentos

Agrega calor y tiempo de lavado al

ciclo

JetClean

Plus Steam (Limpieza

con surtidores y vapor), Normal y

Auto Clean (Limpieza automática)

30 min.

Suciedad rebelde de los

alimentos

Aumenta la temperatura meta del

agua durante las etapas de lavado

del ciclo. Agrega calor, tiempo y

agua.

JetClean

Plus Steam (Limpieza

con surtidores y vapor), Normal y

Auto Clean (Limpieza automática)

5 min.

Suciedad rebelde de los

alimentos

Aumenta la temperatura meta del

agua durante las etapas de lavado

del ciclo. Agrega calor, tiempo y

agua.

JetClean

Plus Steam (Limpieza

con surtidores y vapor), Normal y

Auto Clean (Limpieza automática)

10 min.

Todas las cargas Úselo para obtener mejores

resultados en combinación con el

agente de enjuague. Apáguelo

cuando la carga contenga vajilla de

plástico que pueda ser sensible a

temperaturas más altas.

JetClean

Plus Steam (Limpieza

con surtidores y vapor), Normal,

Light (Ligero), Quick Wash

(Lavado rápido) y Auto Clean

(Limpieza automática)

45 min.

Cargas que necesitan un

secado adicional

Úselo para obtener mejores

resultados en combinación con el

agente de enjuague. Apáguelo

cuando la carga contenga vajilla de

plástico que pueda ser sensible a

temperaturas más altas.

JetClean

Plus Steam (Limpieza

con surtidores y vapor), Normal,

Light (Ligero), Quick Wash

(Lavado rápido) y Auto Clean

(Limpieza automática)

90 min.

Para higienizar los platos

y objetos de cristalería

Aumenta la temperatura del agua en

el enjuague final a aproximadamente

154 ºF (68 ºC). Este enjuague con alta

temperatura higieniza sus platos y su

cristalería según el Estándar NSF/

ANSI 184 para lavavajillas

domésticas. Las lavavajillas

domésticas certificadas no han sido

diseñadas para establecimientos de

alimentos con licencia. La opción

Sanitize (Higienizado) agrega calor y

tiempo al ciclo.

JetClean

Plus Steam (Limpieza

con surtidores y vapor), Normal, y

Auto Clean (Limpieza automática)

30 min.

Todas las cargas Retrasa el inicio de un ciclo hasta por

un máximo de 8 horas.

Todos los ciclos 2, 4, 8

horas

Todas las cargas Cuando el bloqueo del control está

encendido, todos los botones

quedan desactivados. Si usted

oprime cualquier botón mientras su

lavavajillas está con bloqueo, la luz

destellará. La puerta puede abrirse

mientras los controles están

bloqueados.

Todos los ciclos

Sección de información provista por la lavavajillas

Cómo cancelar un ciclo

1. Abra la puerta ligeramente para detener el ciclo. Espere a que

la acción de rociado se detenga antes de abrir la puerta por

completo.

2. Presione una vez el botón CANCEL/DRAIN (Cancelar/

Desaguar). La luz Cancel/Drain se encenderá.

3. Cierre la puerta y la lavavajillas comienza un ciclo de desagüe

(si ha quedado agua en el fondo de la misma). Deje que la

lavavajillas complete el desagüe. La luz Cancel/Drain se apaga

al cabo de 2 minutos.

Cómo cambiar un ciclo después de iniciar la lavavajillas

1. Puede interrumpir un ciclo y volver a iniciar la lavavajillas

desde el comienzo usando el siguiente procedimiento.

2. Abra la puerta ligeramente para detener el ciclo. Espere a que

la acción de rociado se detenga, luego abra la puerta por

completo.

3. Verifique que la tapa del depósito de detergente esté aún

cerrada. Si la tapa está abierta, necesitará volver a llenar el

depósito de detergente antes de volver a iniciar el nuevo ciclo.

4. Presione CANCEL/DRAIN (Cancelar/Desaguar) dos veces

para volver a fijar el control.

5. Seleccione los nuevos ciclos y opciones.

6. Presione START/RESUME (Inicio/Reanudar).

Cómo agregar un plato después de iniciar la lavavajillas

1. Verifique si se ha encendido el indicador de Add a Dish

(Agregar un plato). (Disponible en algunos modelos. De otro

modo, prosiga con el paso 2.)

2. Abra la puerta ligeramente para detener el ciclo. Espere a que

la acción de rociado se detenga, luego abra la puerta por

completo.

3. Verifique si la tapa del depósito de detergente está aún

cerrada. Si está abierta, el ciclo de lavado ya ha comenzado y

no se recomienda agregar un plato.

4. Si el detergente todavía no se usó (la tapa del depósito del

detergente está cerrada), puede agregar un plato.

5. Presione START/RESUME (Inicio/Reanudar).

CONTROLES Y ESTADO DE

LOS CICLOS

CONTROL PROPÓSITO COMENTARIOS

Para iniciar o

reanudar un ciclo de

lavado

Si se abre la puerta durante un ciclo, o si se interrumpe el suministro de energía, destellará

el indicador de START/RESUME (Inicio/Reanudar). El ciclo no se reanudará hasta que se

cierre la puerta y se presione START/RESUME (Inicio/Reanudar).

NOTA: Si el botón de START/RESUME (Inicio/Reanudar) está ubicado sobre la puerta,

empuje la misma firmemente para cerrarla en menos de 3 segundos después de haber

presionado START/RESUME. Si la puerta no se ha cerrado en menos de 3 segundos, el

LED del botón de inicio destellará, se escuchará un tono audible y el ciclo no comenzará.

Para volver a fijar

cualquier ciclo u

opciones durante la

selección.

Para anular un ciclo

de lavado después

de que haya

comenzado.

Presione CANCEL/DRAIN (Cancelar/Desaguar) para volver a fijar las selecciones hechas

en el control.

Vea las secciones “Cómo cancelar un ciclo” y “Cómo cambiar un ciclo después de iniciar

la lavavajillas”.

Para encender o

apagar los tonos

audibles.

Presione y sostenga el botón de Hi Temp Wash (Lavado a temperatura alta) durante

3 segundos para encender o apagar los tonos audibles. Sólo se pueden encender o

apagar los tonos audibles que confirman cuando se presiona un botón. Los tonos

audibles importantes, tales como los que indican cuando se ha interrumpido un ciclo, no

pueden desactivarse.

NOTA: Los tonos audibles no están disponibles en todos los modelos.

CONTROLES Y ESTADO DE LOS CICLOS

CONTROL PROPÓSITO COMENTARIOS

Las luces indicadoras de

estado del ciclo se usan

para seguir el progreso del

ciclo de la lavavajillas. Están

ubicadas en la parte frontal

de la lavavajillas en los

modelos con controles

frontales, y en la parte

superior de la puerta en los

modelos con controles

ocultos.

El indicador de Clean (Limpio) se ilumina cuando se ha terminado un ciclo.

Si usted selecciona la opción de Sani Rinse (Enjuague sanitario), cuando el

ciclo de Enjuague sanitario se ha terminado, la luz indicadora de Sanitized

(Higienizado) se ilumina. Si su lavavajillas no higienizó sus platos

adecuadamente, la luz destella al término del ciclo. Esto puede ocurrir si

se interrumpe el ciclo o si el agua no se pudo calentar hasta llegar a la

temperatura requerida.

Las luces de Clean (Limpio) y Sanitized (Higienizado) se apagan cuando

usted abre y cierra la puerta u oprime CANCEL (Anulación).

La page charge ...

Maytag Dishwasher Mode d'emploi

Marque: Maytag

Modèle: Dishwasher

Catégorie: Lave-vaisselle

Taper: Mode d'emploi

Ce manuel convient également à

MDB8959SBW

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag Dishwasher User guide
español: Maytag Dishwasher Guía del usuario

Documents connexes

Autres documents

Whirlpool KUDS30IXWH Mode d'emploi