BLACK+DECKER BES710 Le manuel du propriétaire

www.blackanddecker.eu

BES700

BES710

2

15

23

18

4

1

12

5

14

18

9

5

13

16

29

5

14

16

31

19

21

20

6

9

32

23

2

30

31012

136

5

36

28

6

3334

6

6 7102611

8

24

13

17

22

18

22

25

27

35

3

17

A

9

B

5

C

33

D

3

E

6 6

6a

6

6a

6

6a

F

4

23

23a

G

4

4a

4b

4c

H

30

13

13a

13c

13b

14

I

31

J

13

13a

13d

13f

13e

K

9

726 24

L

5

27

25

2

M

20

21

19

N

O1 O2

O3 O4

6

P Q1

Q2 Q3

B

A

S1

12

11

R

7

ENGLISH

(Original instructions)

S2

T1

12

11

T2

U

Intended use

Your BLACK+DECKER BES700, BES710 sliding compound

mitre saw has been designed for sawing wood, plastic and

nonferrous metal only. This tool is intended for non profes-

sional users.

Safety instructions

General power tool safety warnings

@

Warning! Read all safety warnings,

 instructions,illustrationsandspecications

provided with power tool. Failure to follow the warnings and

instructions listed below may result in electric shock, re and/

or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below refers

to your mains operated (corded) power tool or battery oper-

ated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

suchasinthepresenceofammableliquids,gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

8

ENGLISH

(Original instructions)

English (Original instructions)

h. Donotletfamiliaritygainedfromfrequentuseoftools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the

power tools operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

h. Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and greasy

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

5. Service

a. Haveyourpowertoolservicedbyaqualiedrepair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Safety instructions for mitre saws

u Mitre saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-off

wheels for cutting ferrous material such as bars, rods,

studs, etc. Abrasive dust causes moving parts such as

the lower guard to jam. Sparks from abrasive cutting will

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

powertoolwhileyouaretiredorundertheinuence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b. Usepersonalprotectiveequipment.Alwaysweareye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can

be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

9

ENGLISH

(Original instructions)

burn the lower guard, the kerf insert and other plastic

parts.

u Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury from blade

contact.

u The workpiece must be stationary and clamped or

held against both the fence and the table. Do not feed

the workpiece into the blade or cut “freehand” in any

way. Unrestrained or moving workpieces could be thrown

at high speeds, causing injury.

u Push the saw through the workpiece. Do not pull the

saw through the workpiece. To make a cut, raise the

saw head and pull it out over the workpiece without

cutting, start the motor, press the saw head down and

push the saw through the workpiece.

Cutting on the pull stroke is likely to cause the saw blade

to climb on top of the workpiece and violently throw the

blade assembly towards the operator.

u Never cross your hand over the intended line of cut-

ting either in front or behind the saw blade. Supporting

the workpiece “cross handed” i.e. holding the workpiece to

the right of the saw blade with your left hand or vice versa

is very dangerous.

u Do not reach behind the fence with either hand closer

than 100 mm from either side of the saw blade, to

remove wood scraps, or for any other reason while

the blade is spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you may be

seriously injured.

u Inspect your workpiece before cutting. If the work-

piece is bowed or warped, clamp it with the outside

bowed face toward the fence. Always make certain

that there is no gap between the workpiece, fence

and table along the line of the cut. Bent or warped

workpieces can twist or shift and may cause binding on

the spinning saw blade while cutting. There should be no

nails or foreign objects in the workpiece.

u Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small de-

bris or loose pieces of wood or other objects that contact

the revolving blade can be thrown with high speed.

u Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced and

may bind on the blade or shift during cutting.

u Ensure the mitre saw is mounted or placed on a level,

rmworksurfacebeforeuse. A level and rm work sur-

face reduces the risk of the mitre saw becoming unstable.

u Plan your work. Every time you change the bevel or

mitre angle setting, make sure the adjustable fence is

set correctly to support the workpiece and will not

interfere with the blade or the guarding system. With-

out turning the tool “ON” and with no workpiece on the

table, move the saw blade through a complete simulated

cut to assure there will be no interference or danger of

cutting the fence.

u Provideadequatesupportsuchastableextensions,

saw horses, etc. for a workpiece that is wider or

longer than the table top. Workpieces longer or wider

than the mitre saw table can tip if not securely supported.

If the cut-off piece or workpiece tips, it can lift the lower

guard or be thrown by the spinning blade.

u Do not use another person as a substitute for a table

extension or as additional support. Unstable support

for the workpiece can cause the blade to bind or the

workpiece to shift during the cutting operation pulling you

and the helper into the spinning blade.

u The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade.

If conned, i.e. using length stops, the cut-off piece could

get wedged against the blade and thrown violently.

u Alwaysuseaclamporaxturedesignedtoproperly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to “bite” and pull the work with your hand into the blade.

u Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

u If the workpiece or blade becomes jammed, turn the

mitre saw off. Wait for all moving parts to stop and

disconnect the plug from the power source and/or re-

move the battery pack. Then work to free the jammed

material. Continued sawing with a jammed workpiece

could cause loss of control or damage to the mitre saw.

u Afternishingthecut,releasetheswitch,holdthe

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

Additional safety instructions for mitre saws

u Holdthehandlermlywhenmakinganincompletecut

or when releasing the switch before the saw head is

completely in the down position. The braking action of

the saw may cause the saw head to be suddenly pulled

downward, causing a risk of injury.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual may present a risk of

personal injury and/or damage to property.

u Do not use cracked/bent/damaged/deformed saw blades.

10

ENGLISH

(Original instructions)

u Replace the kerf plate when worn.

u Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

technical data. Use only the blades specied in this

manual, complying with EN 847-1.

u Do not use High Speed Steel (HSS) saw blades.

@

Warning! Contact with or inhalation of dusts

arising from sawing applications may endanger

the health of the operator and possible bystanders. Wear a

dust mask specically designed for protection against dust

and fumes and ensure that persons within or entering the

work area are also protected.

u Do not work with material containing asbestos. Asbestos

is considered to be carcinogenic.

u Wear gloves when handling saw blades and rough

material (saw blades should be carried in a holder when

practicable).

u Wear hearing protection to reduce the risk of induced

hearing loss.

u Consider using specially designed noise-reduction blades.

u Wear eye protection to reduce the risk of personal injury.

u Use the dust bag provided when sawing wood.

u Hold power tool by insulated gripping surfaces when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord.

Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give

the operator an electric shock

u Select the correct blade for the material to be cut.

u Do not operate the machine without the guard in position.

Do not operate the machine if the guard does not function

or is not maintained properly.

u Ensure that the arm is securely xed when performing

bevel cuts.

u Before each cut ensure that the machine is stable.

u Keep handles dry, clean and free from oil and grease.

u Keep the surrounding area of the machine well maintained

and free of loose materials, e.g. chips and off-cuts.

u Ensure the machine and the work area are provided with

adequate general or localised lighting.

u Do not allow untrained people to operate this machine.

u Ensure that the blade is mounted correctly before use.

Make sure that the blade rotates in the correct direction.

Keep the blade sharp. Follow instruction for lubricating

and changing accessories.

u Ensure the speed marked on the saw blade is at least

equal to the speed marked on the saw.

u Ensure that any spacers and spindle rings used are

suitable for the purpose as stated by BLACK+DECKER.

u Repairs to the cut line guidance system should be carried

out by authorised repair agents or BLACK+DECKER

service staff.

u Unplug the machine before carrying out any maintenance

or when changing the blade.

u Never perform any cleaning, maintenance, removal of any

off-cuts or other parts of the work piece form the cutting

area when the machine is running and the saw head is not

in the rest position.

u When possible, always mount the machine to a bench.

u Make sure all locking knobs and handles are tight before

starting any operation.

u Never use your saw without the table insert.

u Never attempt to stop the machine in motion rapidly by

jamming a tool or other means against the blade; serious

accidents can be caused unintentionally in this way.

u Before using or tting any accessory consult the instruc-

tion manual. The improper use of an accessory can cause

damage.

u Raise the blade from the table insert in the work piece

prior to releasing the on/of switch.

u Do not wedge anything against the fan to hold the motor

shaft.

u The blade guard on your saw will automatically raise when

the arm is brought down; it will lower over the blade when

the arm is raised. The guard can be raised by hand when

installing or removing saw blades or for inspection of the

saw. Never raise the blade guard manually unless the

machine is switched off.

u Check periodically that the motor air slots are clean and

free of chips.

u Never make the warning signs on the power tool unrecog-

nisable.

u Never stand on the power tool. Serious injuries could

occur when the power tool tips over or when coming in

contact with the saw blade.

u Do not take hold of the saw blade after working before it

has cooled. The saw blade becomes very hot while work-

ing.

u To avoid injury from materials being thrown, unplug the

saw to avoid accidental starting, and then remove small

materials.

u Before use and after any maintenance the blade guard

must be checked to ensure proper function. This test must

be performed with the saw switched off and unplugged.

The arm must be raised and lowered to ensure the

guard covers the blade and the blade does not contact

the guard. If the guard fails to operate correctly, have

your power tool serviced by a qualied repair agent. Call

BLACK+DECKER customer services for you nearest

service agent.

u This mitre saw has been designed for sawing wood,

plastic and nonferrous metal only. Do not use the saw

to cut other materials than those recommended by the

manufacturer.

11

ENGLISH

(Original instructions)

u Do not take hold of the saw blade after working before it

has cooled. The saw blade becomes very hot while

working.

@

Warning! Cutting plastics, sap coated wood, and

other materials may cause melted material to

accumulate on the blade tips and the body of the saw blade,

increasing the risk of the blade overheating and binding while

cutting.

Residual risks

The following risks are inherent to the use of saws:

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Impairment of hearing.

u Risk of accidents caused by the uncovered parts of the

rotating saw blade.

u Risk of injury when changing any parts, blades or acces-

sories.

u Risk of squeezing ngers when opening the guards.

u Health hazards caused by breathing dust developed when

sawing wood, especially oak, beech and MDF.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

Noise

The declared noise emission values have been measured in

accordance with a standard test method and may be used for

comparing one tool with another.

The declared noise emission values may also be used in a

preliminary assessment of exposure.

Warning! The noise emissions during actual use of the

power tool can differ from the declared values depending

on the ways in which the tool is used especially what kind of

workpiece is processed.

Warning! Always wear proper personal hearing protec-

tion. Under some conditions and duration of use, noise from

this product may contribute to hearing loss. Be aware of the

following factors inuencing exposure to noise:

u Use saw blades designed to reduce the emitted noise,

u Use only well sharpened saw blades, and

u Use specically designed noise-reduction saw blades.

Labels on tool

The following pictograms along with the date code are shown

on the tool:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Wear safety glasses or goggles

Wear ear protection

Wear a dust mask

This product is not to be used by children

under 16

Keep hands away from blade

No Hands Zone - Keep ngers and arms away

from rotational saw blades

Wear gloves when handling saw blades

Do not stare at operating lamp

Do not expose to rain.

Disconnect the mains plug if the cord

becomes damamged or entangled.

Electrical safety

#

This tool is double insulated; therefore no

earth wire is required. Always check that the

power supply corresponds to the voltage on

the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Voltage drops

Inrush currents cause short-time voltage drops. Under unfa-

vourable power supply conditions, other equipment may be

affected. If the system impedance of the power supply is lower

than 0.178 Ω, disturbances are unlikely to occur.

Using an extension cable

Always use an approved extension cable suitable for the

power input of this tool (see technical data). Before use,

inspect the extension cable for signs of damage, wear and

ageing. Replace the extension cable if damaged or defective.

When using a cable reel, always unwind the cable completely.

Use of an extension cable not suitable for the power input of

the tool or which is damaged or defective may result in a risk

of re and electric shock.

Features

This tool includes some or all of the following features.

1. Slide bars

12

ENGLISH

(Original instructions)

Table extension rail (Fig. C & D)

Your mitre saw is supplied with 2 table extension rails (5) to

support long overhanging workpieces.

uPull the table extension rail (5) to the required length for

the workpiece as shown in gure C.

uSecure in position by tightening the extension rail locking

screw (33), as shown in gure D.

uRepeat the process on opposite side.

Support stand - BES710 only (Fig. E)

Your BES710 mitre saw is supplied with 1 support stand (3),

located at the rear of the unit, to enhance stability.

Bench mounting (Fig. F)

The mitre saw can be bolted with four bolts (6a) (not provided)

to a level and stable surface using the bolt holes (6) provided

in the tools base. This will help prevent tipping and possible

injury.

Dust collection (Fig. G)

The use of the dust bag (23) makes cutting operations clean

and dust collection easy.

u To attach the dust bag (23), t it onto the dust nozzle

(23a).

u When the dust bag (23) is about half full, remove it from

the tool.

u Empty the dust bag of its contents, tapping it lightly so as

to remove particles adhering to the insides which might

hamper further collection.

Note: If you connect a workshop vacuum to your saw, more

efcient and cleaner operations can be performed.

To install workpiece clamp (Fig. H)

uInsert the clamp (4) into the hole (4c) behind the

fence. The clamp should be facing toward the

back of the miter saw. The groove on the clamp

rod should be fully inserted into the base. Ensure

this groove is fully inserted into the base of the

miter saw. If the groove is visible, the clamp will

not be secure.

uRotate the clamp 180º toward the front of the

miter saw.

uLoosen the knob (4b) to adjust the clamp up or down,

then use the ne adjust knob (4a) to rmly clamp the

workpiece.

Note: Place the clamp on the opposite side of the base when

beveling. ALWAYS MAKE DRY RUNS (UNPOWERED) BE-

FORE FINISH CUTS TO CHECK THE PATH OF THE BLADE.

ENSURE THE CLAMP DOES NOT INTERFERE WITH THE

ACTION OF THE SAW OR GUARDS.

2. Bevel lock knob

3. Support stand

4. Work piece clamp

5. Table extension rail

6. Bolt holes

7. Mitre angle indicator

8. Table insert

9. Mitre lock knob

10. Base plate

11. Rotary table

12. Rear fence

13. Saw blade

14. Blade guard

15. Safety guard mounting plate

16. Motor housing

17. Saw head locking pin

18. Main handle

19. Trigger switch

20. Safety release lever

21. Cut line light on/off button

22. Carry handle

23. Dust bag

24. Adjustable support foot

25. Bevel angle indicator

26. Mitre angle scale

27. Bevel angle scale

28. Slide bar locking screw

29. Depth of cut screw

30. Blade change tool

31. Spindle lock

32. Mitre lock release

33. Extension rail locking screw

34. Clamp lock screw

35. Slide fence locking screw

36. Cable wrap

Assembly

Your mitre saw is part assembled in the carton.

uOpen the box and lift the saw out.

u Place the saw on a smooth, at surface such as a work-

bench or strong table.

u Examine Assembly diagram on page 2 of this manual to

become familiar with the saw and its various parts. The

section on adjustments will refer to these terms and you

must know what and where the parts are.

u When the tool is shipped, the handle is locked in the

lowered position by the saw head locking pin (17). Pull

the saw head locking pin (17) and rotate it 90º, either

clockwise or counterclockwise as shown in gure A.

u The mitre locking knob (9) is not assembled for shipping.

Remove the mitre locking knob (9) from the packaging

and screw onto the saw, see gure B for position.

13

ENGLISH

(Original instructions)

Changing or installing a new saw blade (Fig. I,

J, K)

Warning! To reduce the risk of serious personal injury, turn

off the tool and disconnect it from the power source before

attempting to move it, change accessories or make any

adjustments.

Warning! Never depress the spindle lock (31) button while the

blade is under power or coasting.

Warning! Do not cut ferrous metal (containing iron or steel) or

masonry or ber cement product with this mitre saw.

Removing the blade

uUnplug the saw.

uRaise the arm to the upper position and push the guard

(14) up as far as possible.

uLoosen, but do not remove guard bracket screw (13c) until

the bracket can be raised far enough to access the

blade screw (13a). Lower guard will remain raised due to

the position of the guard bracket screw as shown in

gure I.

uDepress the spindle lock button (31) while carefully

rotating the saw blade by hand until the lock engages as

shown in gure J.

uKeeping the button depressed, use the other hand and

the blade changing tool provided (30) to loosen the blade

screw (13a). (Turn clockwise, left-hand threads.)

uRemove the blade screw (13a), outer clamp washer

(13d), blade (13) and blade adapter (13e), if used. The

inner clamp washer (13f) may be left on the spindle.

Installing a blade

uUnplug the saw.

uWith the arm raised, the guard held open and the guard

bracket raised, place the blade on the spindle, onto the

blade adapter and against the inner blade clamp with the

teeth at the bottom of the blade pointing toward the back

of the saw.

uAssemble the outer clamp washer onto the spindle.

uInstall the blade screw and, engaging the spindle lock,

tighten the screw rmly with wrench provided (turn coun-

terclockwise, left-hand threads).

Adjusting the mitre angle (Fig. L)

uLoosen the grip (9) by turning counterclockwise.

uUse the mitre lock release (32) to move the rotary table

(11) to the position where the pointer (7) points to the

desired angle on the mitre scale (26), tighten the grip

clockwise.

uThe adjustable support foot (24) is to help keep the tool in

balance. After each mitre angle adjustment, you should

turn knob on the foot clockwise or counterclockwise until

its bottom touches the ground. There are two positions

depending on the depth of your work bench.

Cutting depth

If you want to cut a groove you can set the depth of cut using

the depth of cut screw (29) or the blade.

uTurn the depth of cut screw (29) and x with the counter

nut.

Fence adjustment

Before bevel cutting, make sure that no part of the tool

contacts the fence (12) when lowering and raising the handle

fully at any position and pulling or pushing the carriage all the

way at the lowest position. Before operating the tool, make

sure that the sliding fence is secured by the slide nce locking

screw (35) rmly.

Warning! When performing bevel cuts, slide the sliding fence

to the left and secure. Otherwise, it will contact the blade or a

part of the tool, causing possible serious injury to the operator.

This tool is equipped with the sliding fence which should

ordinarily be positioned central. However, when performing left

bevel cuts, set it to the left position if the tool head contacts it.

When bevel cutting operations are complete, don't forget to

return the sliding fence to the original position and secure it by

rmly tightening the slide fence locking screw (35).

Adjusting the bevel angle (Fig. M)

When tilting the carriage to the left, loosen the lever (2) at the

rear of the tool counterclockwise. Unlock the arm by pushing

the handle somewhat strongly in one direction only.

uTilt the saw blade until the pointer (25) points to the

desired angle on the bevel scale (27).

uTighten the lever (2) clockwise rmly to secure the arm.

Warning! When tilting the saw blade, be sure to raise the

handle fully. After changing the bevel angle, always secure the

arm by tightening the lever clockwise.

Warning! When tilting the saw blade, always be aware of the

weight of the head and make sure to avoid it crashing over.

Switch action (Fig. N)

Caution! Before plugging in the tool, always check to see that

the switch trigger (19) actuates properly and returns to the

"OFF" position when released.

u To start the tool, move the safety release lever (20) to the

right with your index nger.

u Press the switch trigger (19).

u To stop the tool, release the switch trigger (19).

Warning! Never use tool without a fully operative switch

trigger. Any tool with an inoperative switch is

HIGHLY DANGEROUS and must be repaired before usage.

Use of Cut line System (Fig. N)

Note: The mitre saw must be connected to a power source.

The Cut line System is equipped with an on/off switch (21).

14

ENGLISH

(Original instructions)

The Cut line System is independent of the mitre saw’s trigger

switch.

The light does not need to be on in order to operate the saw.

To cut through an existing pencil line on a piece of wood:

u Turn on the Cut line system, then pull down on the operat-

ing handle (18) to bring the saw blade close to the wood.

The shadow of the blade will appear on the wood.

u Align the pencil line with the edge of the blade’s shadow.

You may have to adjust the mitre or bevel angles in order

to match the pencil line exactly.

Crosscuts

A crosscut is made by cutting wood across the grain at any

angle. A straight crosscut is made with the miter arm at the

zero degree position. Set and lock the miter arm at zero, hold

the wood rmly on the table and against the fence. With the

rail lock knob tightened, turn on the saw by squeezing the

trigger switch (19).

When the saw comes up to speed (about 1 second) lower

the arm smoothly and slowly to cut through the wood. Let the

blade come to a full stop before raising arm.

When cutting anything larger than a 51mm x 102mm, use an

out-down-back motion with the rail lock knob loosened.

Pull the saw out, toward you, lower the saw head down toward

the workpiece, and slowly push the saw back to complete the

cut. Do not allow the saw blade to contact the top of the work-

piece while pulling out. The saw may run toward you, possibly

causing personal injury or damage to the workpiece.

Warning! Always use a work clamp to maintain control and

reduce the risk of workpiece damage and personal injury.

Note: The rail lock knob must be loose to allow the saw

to slide along its rails.

Miter crosscuts are made with the miter arm at some angle

other than zero. This angle is often 45º for making corners, but

can be set anywhere from zero to 47º left or 47° right. Make

the cut as described above.

To cut through an existing pencil line on a piece of wood,

match the angle as close as possible. Cut the wood a little too

long and measure from the pencil line to the cut edge to

determine which direction to adjust the miter angle and

recut. This will take some practice, but it is a commonly used

technique.

Body and hand position (Fig. O1 – O4)

Proper positioning of your body and hands when operating the

miter saw will make cutting easier, more accurate and safer.

Never place hands near cutting area. Place hands no closer

than 152 mm from the blade. Hold the workpiece tightly to

the table and the fence when cutting. Keep hands in position

until the trigger has been released and the blade has

completely stopped. ALWAYS MAKE DRY RUNS

(UNPOWERED) BEFORE FINISH CUTS SO THAT YOU

CAN CHECK THE PATH OF THE BLADE.

DO NOT CROSS HANDS, AS SHOWN IN FIGURE O3 and

O4.

Keep both feet rmly on the oor and maintain proper

balance. As you move the miter arm left and right, follow it and

stand slightly to the side of the saw blade. Sight through the

guard louvers when following a pencil line.

Bevelsquaretotableadjustment(Fig.P)

To align the blade square to the table, lock the arm in the

down position with the lock down pin. Place a square

against the blade, ensuring the square is not on top of a tooth.

Loosen the bevel lock knob and ensure the arm is rmly

against the 0° bevel stop. Rotate the 0° bevel adjustment

screw with the 10 mm spanner (not provided) as necessary so

that the blade is at 0° bevel to the table, as measured

with the square.

Cutting picture frames, shadow boxes and other

four-sided projects (Fig. Q1, Q2)

To best understand how to make the items listed here, we

suggest that you try a few simple projects using scrap wood

until you develop a “feel” for your saw.

Your saw is the perfect tool for mitering corners like the one

shown in Figure Q1. Sketch A in Figure Q2 shows a joint

made by using the bevel adjustment to bevel the edges of

the two boards at 45º each to produce a 90º corner. For this

joint the miter arm was locked in the zero position and the

bevel adjustment was locked at 45º. The wood was positioned

with the broad at side against the table and the narrow edge

against the fence. The cut could also be made by mitering

right and left with the broad surface against the fence.

Cutting trim molding and other frames (Fig. Q2)

Sketch B in Figure Q2 shows a joint made by setting the miter

arm at 45º to miter the two boards to form a 90º corner. To

make this type of joint, set the bevel adjustment to zero and

the miter arm to 45º. Once again, position the wood with the

broad at side on the table and the narrow edge against the

fence.

Figures Q1 and Q2 are for four-sided objects only.

As the number of sides changes, so do the miter and bevel

angles.

15

ENGLISH

(Original instructions)

The chart below gives the proper angles for a variety

of shapes.

Number of Sides Miter or Bevel Angle

4 45º

5 36º

6 30º

7 25.7º

8 22.5º

9 20º

10 18º

The chart assumes that all sides are of equal length. For a

shape that is not shown in the chart, use the following formula:

180º divided by the number of sides equals the miter (if the

material is cut vertically) or bevel angle (if the material is cut

laying at).

Cuttingcompoundmiters(g.Q3)

A compound miter is a cut made using a miter angle and a

bevel angle at the same time. This is the type of cut used to

make frames or boxes with slanting sides like the one shown

in gure Q3.

Note: If the cutting angle varies from cut to cut, check that

the bevel lock knob and the miter lock handle are securely

locked. These must be locked after making any changes in

bevel or miter.

Cutting base molding (Fig. R)

Straight 90º cuts:

Position the wood against the fence and hold it in place as

shown in Figure R. Turn on the saw, allow the blade to reach

full speed and lower the arm smoothly through the cut.

Cutting base molding up to 70 mm / 90 mm high

vertically against the Fence

BES700 - 70 mm for 216 mm

BES710 - 90 mm for 254 mm

Position material as shown in Figure R All cuts should be

made with the back of the molding against the fence and with

the bottom of the molding against the table.

Inside Corner Outside Corner

Left Side Miter left 45°

Save left side of cut

Miter right 45°

Save left side of cut

Right Side Miter right 45°

Save right side of

cut

Miter left 45°

Save right side of

cut

Material up to 70 mm / 90mm can be cut as described above.

BES700 - 70 mm for 216 mm

BES710 - 90 mm for 254 mm

Cutting crown molding

In order to t properly, crown molding must be compound

mitered with extreme accuracy.

The two at surfaces on a given piece of crown molding are

at angles that, when added together, equal exactly 90°. Most,

but not all, crown molding has a top rear angle (the section

that ts at against the ceiling) of 52° and a bottom rear angle

(the part that ts at against the wall) of 38°.

Your miter saw has special pre-set miter detent points at 31.6°

left and right for cutting crown molding at the proper angle.

There is also a mark on the bevel scale at 33.9°.

The Bevel Setting/Type of Cut chart gives the proper settings

for cutting crown molding. (The numbers for the miter and

bevel settings are very precise and are not easy to accurately

set on your saw.) Since most rooms do not have angles of

precisely 90°, you will have to ne tune your settings anyway.

Instructionsforcuttingcrownmoldinglayingat

and using the compound features

u Lay the molding with broad back surface down at on saw

table (g. S1).

u The settings below are for all Standard crown molding with

52° and 38° angles.

Bevel Setting Type Of Cut

33.9°

LEFT SIDE, INSIDE CORNER:

1. Top of molding against fence

2. Miter table set right 31.6°

3. Save left end of cut

33.9°

RIGHT SIDE, INSIDE CORNER:

1. Bottom of molding against fence

2. Miter table set left 31.6°

3. Save left end of cut

33.9°

LEFT SIDE, OUTSIDE CORNER:

1. Bottom of molding against fence

2. Miter table set left 31.6°

3. Save right end of cut

33.9°

RIGHT SIDE, OUTSIDE CORNER:

1. Top of molding against fence

2. Miter table set right 31.6°

3. Save right end of cut

Note: When setting bevel and miter angles for all compound

miters, remember that the angles presented for crown

moldings are very precise and difcult to set exactly. Since

they can easily shift slightly and very few rooms have exactly

square corners, all settings should be tested on scrap

molding.

16

ENGLISH

(Original instructions)

Alternative method for cutting crown molding

Place the molding at an angle between the fence (12) and the

saw table (11), with the top side of the molding on the table

and the bottom side of the molding on the fence as shown

in gure S2.

The advantage to cutting crown molding using this method

is that no bevel cut is required. Minute changes in the miter

angle can be made without affecting the bevel angle. This

way,when corners other than 90º are encountered, the saw

can be quickly and easily adjustedfor them.

Instructions for cutting crown molding angled

between the fence and base of the saw for all cuts

This saw can cut up to 14 mm x 92 mm crown molding nested.

u Angle the molding so the bottom of the molding (part

which goes against the wall when installed) is against the

fence (12) and the top of the molding is resting on the saw

table (11), as shown in gure S2.

u The angled “ats” on the back of the molding must rest

squarely on the fence and saw table.

Inside Corner Outside Corner

Left Side Miter right at 45°

Save right side of cut

Miter left at 45°

Save right side of cut

Right Side Miter left at 45°

Save left side of cut

Miter right at 45°

Save left side of cut

Special Cuts

Never make any cut unless the material is secured on the

table and against the fence.

Bowedmaterial(g.T1,T2)

When cutting bowed material always position it as shown in

gure T1 and never like that shown in gure T2. Positioning

the material incorrectly will cause it to pinch the blade near

the completion of the cut.

Cutting round material

Rounded material should be clamped or held rmly to the

fence to keep It from rolling. This is extremely important when

making angle cuts.

Cuttinglargematerial(g.U)

Occasionally you will encounter a piece of wood a little too

large to t beneath the lower guard.

To clear the guard over the wood, with the saw off and your

right hand on the operating handle, place your right thumb

outside of the upper portion of the guard and roll the guard up

just enough to clear the wood, as shown in gure U. Release

the guard prior to starting the motor. The guard mechanism

will function properly during the cut. Only do this when neces-

sary.

NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD

OPEN WHEN OPERATING THIS SAW.

Warning! Always be sure that the tool is switched off and

unplugged before adjusting or checking the tools function.

After use

u After use, wipe off chips and dust adhering to the tool with

a cloth or the like.

u Keep the blade guard clean according to the directions in

the previously covered section.

u Lubricate the sliding portions with machine oil to prevent

rust.

u When storing the tool, pull the carriage toward you fully.

Carrying the tool

u Make sure the tool is unplugged.

u Secure the blade at the 0° bevel angle and turn the base

to the right mitre angle fully with the slide bar locking scre

(28).

u Secure the slide bars after pulling the carriage toward you

fully.

u Lower the handle fully and lock it in the position by

pushing in the saw head locking pin (17).

u Carry the tool by holding the carry handle (22).

u If you remove the clamp, dust bag, etc., you can carry the

tool more easily.

u Carry the tool by one hand holding the carrying handle

(22) and one hand holding the tool base.

Caution! Always secure all moving portions before carrying

the tool.

Saw head locking pin (17) is for carrying and storage

purposes only and not for any cutting operations.

Troubleshooting

Problem Possible Cause Solution

Motor does

not start

Saw not plugged in. Check that all cords are plugged in.

Angle of cut

inaccurate

Mitre table

unlocked.

Use mitre table locking lever (see

Adjusting the mitre angle section.

Too much sawdust

under table.

Vacuum or blow out dust. Wear eye

protection.

Cutting arm

cannot fully

raise, or blade

guard cannot

fully close

Parts Failure. Contact service centre.

Pivot spring not

replaced properly

after service.

Contact service centre.

Sawdust build up. Clean and lubricate moving parts.

Saw head locking

pin not set properly.

Check, adjust, and properly set saw

head locking pin.

Blade binds,

jams or

shakes

Saw blade

damaged.

Replace blade.

Dull blade. Replace or sharpen blade.

Improper blade. Replace blade.

Warped blade. Replace blade.

17

ENGLISH

(Original instructions)

Problem Possible Cause Solution

Saw vibrates

or shakes

Saw blade

damaged.

Replace blade.

Saw blade

loosened.

Tighten arbor bolt.

Saw not properly

fastened down.

Fasten saw to bench, stand or table.

Work piece not

properly supported.

Properly support or clamp work

piece.

Protecting the environment

Z

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

household waste.

Products and batteries contain materials that can be

recovered or recycled reducing the demand for raw materials.

Please recycle electrical products and batteries according to

local provisions. Further information is available at

www.2helpU.com

Technical data

BES700

Type 1

BES710

Type 1

Voltage V 230 230

Speed /min 4800 5000

Blade outer diameter mm 216 254

Bore diameter mm 30 30

Weight kg 12.1 14.9

Blade thickness mm 1.8 1.8

Blade max. kerf mm 2.8 2.8

Mitre (max. positions) ° +/- 47 +/- 47

Bevel (max. positions) ° 47 47

Max. cross-cut capacity at 90 ° mm 305 305

Max mitre capacity at 45 ° mm 203 203

Max. dept cut at 90 ° mm 70 90

Max. dept cut at 45 ° mm 35 40

BES700 - Level of sound pressure according to EN 62841:

L

pA

(sound pressure) 97.5 dB(A), Uncertainty (K) 3 dB(A)

L

WA

(sound power) 108.0 dB(A), Uncertainty (K) 3 dB(A)

BES710 - Level of sound pressure according to EN 62841:

L

pA

(sound pressure) 96.0 dB(A), Uncertainty (K) 3 dB(A)

L

WA

(sound power) 107.5 dB(A), Uncertainty (K) 3 dB(A)

EC declaration of conformity

MACHINERY DIRECTIVE

%

BES700, BES710 Sliding Compound Mitre Saw

Black & Decker declares that these products described under

"technical data" are in compliance with:

EN62841-1:2015, EN62841-3-9:2015+A11:2017

These products also comply with Directive

2006/42/EC, 2014/30/EU and 2011/65/EU.

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the

technical le and makes this declaration on behalf of

Black & Decker.

A. P. Smith

Technical Director

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

01/03/2019

Guarantee

Black & Decker is condent of the quality of its products and

offers consumers a 24 month guarantee from the date

of purchase. This guarantee is in addition to and in no way

prejudices your statutory rights. The guarantee is valid within

the territories of the Member States of the European Union

and the European Free Trade Area.

To claim on the guarantee, the claim must be in accordance

with Black & Decker Terms and Conditions and you will need

to submit proof of purchase to the seller or an authorised re-

pair agent. Terms and conditions of the Black & Decker 2 year

guarantee and the location of your nearest authorised repair

agent can be obtained on the Internet at www.2helpU.com, or

by contacting your local Black & Decker ofce at the address

indicated in this manual.

Please visit our website www.blackanddecker.co.uk to register

your new BLACK+DECKER product and receive updates on

new products and special offers.

18

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

Verwendungszweck

Die verstellbaren Kappgehrungssägen BES700, BES710 von

BLACK+DECKER wurde ausschließlich zum Sägen von Holz,

Kunststoff und Buntmetallen entwickelt. Dieses Gerät ist zum

privaten Einsatz vorgesehen.

Sicherheitshinweise

Allgemeine Sicherheitswarnungen für das Gerät

@

Warnung! Beachten Sie alle

Sicherheitshinweise, Anweisungen,

Darstellungen und Daten, die Sie mit dem Gerät

erhalten.

Die Nichteinhaltung der folgenden Warnungen und

Anweisungen kann einen elektrischen Schlag, Brand und/oder

schwere Verletzungen verursachen.

Bewahren Sie alle Warnhinweise und alle Anweisungen

gut auf.

Der nachfolgend verwendete Begriff "Gerät" bezieht

sich auf netzbetriebene Geräte (mit Netzkabel) und auf

akkubetriebene Geräte (ohne Netzkabel).

1. Sicherheit im Arbeitsbereich

a. Halten Sie Ihren Arbeitsbereich sauber und gut

ausgeleuchtet. Unaufgeräumte oder dunkle Bereiche

begünstigen Unfälle.

b. Betreiben Sie das Gerät nicht in Umgebungen, in

denen Explosionsgefahr z. B. aufgrund von

brennbaren Flüssigkeiten, Gasen oder Staub besteht.

Geräte erzeugen Funken, die den Staub oder die Dämpfe

entzünden können.

c. Halten Sie Kinder und andere Personen während der

Benutzung eines Elektrowerkzeugs fern. Bei Ablenkung

können Sie die Kontrolle verlieren.

2. Elektrische Sicherheit

a. Der Netzstecker des Geräts muss in die Steckdose

passen. Ändern Sie niemals den Stecker in

irgendeiner Form. Verwenden Sie keinerlei

Adapterstecker an geerdeten Elektrogeräten.

Unveränderte Stecker und passende Steckdosen mindern

die Gefahr eines elektrischen Schlages.

b. Vermeiden Sie Körperkontakt mit geerdeten

OberächenvonRohren,Heizungen,Herdenund

Kühlschränken. Es besteht eine erhöhte Gefahr für einen

elektrischen Schlag, wenn Ihr Körper geerdet ist.

c. Halten Sie Geräte von Regen und Nässe fern. Wenn

Wasser in das Elektrogerät eindringt, erhöht sich die

Gefahr eines elektrischen Schlages.

d. Verwenden Sie das Kabel ordnungsgemäß.

Verwenden Sie es niemals zum Tragen. Trennen Sie

das Gerät nicht durch Ziehen am Kabel vom Netz.

Halten Sie das Kabel fern von Hitze, Öl, scharfen

Kanten oder beweglichen Teilen. Beschädigte oder

verhedderte Kabel erhöhen die Gefahr eines elektrischen

Schlages.

e. Verwenden Sie nur für den Außenbereich zugelassene

Verlängerungskabel, wenn Sie mit dem

Elektrowerkzeug im Freien arbeiten. Die Verwendung

von für den Außeneinsatz geeigneten Kabeln mindert die

Gefahr eines elektrischen Schlages.

f. Wenn das Elektrowerkzeug in einer feuchten

Umgebung verwendet werden muss, schließen Sie es

unbedingt an eine Steckdose mit

Fehlerstromschutzschalter (FI-Schalter) an. Ein

Fehlerstromschutzschalter verringert das Risiko eines

elektrischen Schlags.

3. Sicherheit von Personen

a. Seien Sie aufmerksam, achten Sie darauf, was Sie tun,

und gehen Sie sachgerecht mit einem

Elektrowerkzeug um. Benutzen Sie kein

Elektrowerkzeug, wenn Sie müde sind oder unter dem

EinussvonDrogen,AlkoholoderMedikamenten

stehen. Ein Moment der Unachtsamkeit beim Betrieb

eines Elektrowerkzeugs kann zu schweren Verletzungen

führen.

b. Verwenden Sie eine geeignete Schutzausrüstung.

Tragen Sie immer einen Augenschutz. Das Tragen

persönlicher Schutzausrüstung, wie Staubmaske,

rutschfeste Sicherheitsschuhe, Schutzhelm oder

Gehörschutz, je nach Art und Einsatz des Geräts,

verringert das Risiko von Verletzungen.

c. Vermeiden Sie eine unbeabsichtigte Inbetriebnahme.

Vergewissern Sie sich, dass das Gerät ausgeschaltet

ist, bevor Sie es an eine Steckdose oder einen Akku

anschließen, es hochheben oder tragen. Wenn Sie

beim Tragen des Geräts den Finger am Schalter haben

oder das Gerät eingeschaltet an die Stromversorgung

anschließen, kann dies zu Unfällen führen.

d. Entfernen Sie Einstell- oder Schraubenschlüssel,

bevor Sie das Gerät einschalten. Werkzeuge oder

Schlüssel, die an rotierenden Teilen des Elektrogerätes

angebracht sind, können zu Verletzungen führen.

e. Beugen Sie sich nicht zu weit nach vorne. Sorgen Sie

für einen sicheren Stand und halten Sie jederzeit das

Gleichgewicht. Dadurch können Sie das Gerät in

unerwarteten Situationen besser kontrollieren.

f. Tragen Sie geeignete Kleidung. Tragen Sie keine weite

Kleidung und keinen Schmuck. Halten Sie Ihre Haare

und Kleidung von beweglichen Teilen fern. Lose

sitzende Kleidung, Schmuck oder lange Haare können

sich in den beweglichen Teilen verfangen.

g. Falls Vorrichtungen zum Absaugen oder Auffangen

von Staub vorhanden sind, vergewissern Sie sich,

dass diese angeschlossen sind und richtig verwendet

19

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

werden. Das Verwenden einer Staubauffangvorrichtung

verringert Gefährdungen durch Staub.

h. VermeidenSie,durchdiehäugeNutzungdes

Werkzeugs in einen Trott zu verfallen und Prinzipien

für die Werkzeugsicherheit zu ignorieren. Eine

unachtsame Aktion kann im Bruchteil einer Sekunde zu

schweren Verletzungen führen.

4. GebrauchundPegevonGeräten

a. Überlasten Sie das Gerät nicht. Verwenden Sie das für

Ihre Arbeit passende Gerät. Das richtige Gerät wird die

Aufgabe besser und sicherer erledigen, wenn es

bestimmungsgemäß verwendet wird.

b. Verwenden Sie das Gerät nicht, wenn der Ein-/

Ausschalter nicht funktioniert. Ein Gerät, das sich nicht

mehr ein- oder ausschalten lässt, ist gefährlich und muss

repariert werden.

c. Ziehen Sie den Stecker aus der Steckdose, oder

trennen Sie das Gerät vom Akku, bevor Sie

Einstellungen vornehmen, Zubehörteile wechseln

oder das Gerät lagern. Diese Vorbeugemaßnahmen

mindern die Gefahr, dass das Elektrogerät unbeabsichtigt

startet.

d. Bewahren Sie unbenutzte Geräte außerhalb der

Reichweite von Kindern auf. Lassen Sie Geräte nicht

von Personen benutzen, die damit nicht vertraut sind

oder diese Anweisungen nicht gelesen haben.

Geräte sind in den Händen nicht geschulter Personen

gefährlich.

e. Halten Sie das Gerät und sein Zubehör in einem

einwandfreien Zustand. Kontrollieren Sie, ob

bewegliche Teile falsch ausgerichtet sind oder

klemmen und ob Teile gebrochen oder so beschädigt

sind, dass die Funktion des Geräts beeinträchtigt ist.

Bei Beschädigungen lassen Sie das Gerät reparieren,

bevor Sie es verwenden. Viele Unfälle entstehen wegen

mangelnder Wartung der Geräte.

f. Halten Sie Schneidgeräte scharf und sauber. Richtig

gewartete Schneidwerkzeuge mit scharfen Klingen

blockieren seltener und sind leichter unter Kontrolle zu

halten.

g. Verwenden Sie Gerät, Zubehör, Einsatz-Bits usw.

entsprechend diesen Anweisungen und

berücksichtigen Sie dabei die Arbeitsbedingungen

und die auszuführende Arbeit. Der Gebrauch von

Elektrowerkzeugen für andere als die vorgesehenen

Zwecke kann zu gefährlichen Situationen führen.

h. Halten Sie die Griffe trocken, sauber und frei von Öl

und Fett. Rutschige Griffe und fettige Oberächen

unterbinden die sichere Bedienbarkeit und Kontrolle über

das Werkzeug in unerwarteten Situationen.

5. Service

a. LassenSieIhrElektrowerkzeugnurvonqualiziertem

Fachpersonal und nur mit Original-Ersatzteilen

reparieren. Damit wird sichergestellt, dass die Sicherheit

des Geräts erhalten bleibt.

Sicherheitshinweise für Gehrungssägen

uGehrungssägen sind zum Schneiden von Holz oder

holzähnlichen Produkten bestimmt. Sie dürfen nicht

mit Trennscheiben zum Schneiden von eisenhaltigem

Material wie Stangen, Stäben, Bolzen usw. verwendet

werden. Staubpartikel führen dazu, dass sich bewegliche

Teile wie die untere Schutzvorrichtung verklemmen.

Durch Funken beim Trennschneiden können die untere

Schutzvorrichtung, der Sägeschlitzeinsatz und andere

Kunststoffteile einbrennen.

uVerwenden Sie nach Möglichkeit stets

Schraubklemmen, um das Werkstück einzuspannen.

WennSiedasWerkstückmitderHandxieren,

müssen Sie Ihre Hand mindestens 100 mm von

beiden Seiten des Sägeblatts fernhalten. Nutzen Sie

diese Säge nicht zum Schneiden von Teilen, die zu

klein sind, um sicher eingespannt oder mit der Hand

gehalten zu werden. Wenn sich Ihre Hand zu nahe am

Sägeblatt bendet, besteht ein höheres Verletzungsrisiko

durch Kontakt mit dem Sägeblatt.

uDas Werkstück muss fest stehen und eingespannt

sein oder gegen die Eingrenzung und den Tisch

gestützt werden. Führen Sie das Werkstück nicht zum

Sägeblatt oder schneiden Sie es auf irgendeine Art

„frei Hand“. Nicht xierte oder bewegliche Werkstücke

können mit hohen Geschwindigkeiten weggeschleudert

werden und zu Verletzungen führen.

uDrücken Sie die Säge durch das Werkstück. Ziehen

Sie die Säge nicht durch das Werkstück. Um einen

Schnitt zu machen, heben Sie den Sägekopf an,

ziehen Sie diesen ohne zu schneiden über das

Werkstück, starten Sie den Motor, drücken Sie den

Sägekopf nach unten, und drücken Sie die Säge durch

das Werkstück. Das Schneiden bei Zugspannung führt

oft dazu, dass das Sägeblatt aus dem Werkstück steigt

und die Sägeblattbaugruppe gewaltsam in Richtung des

Bedieners schleudert.

uBringen Sie Ihre Hände nie in die vorgesehene

Schnittlinie, wieder vor noch hinter das Sägeblatt. Das

Abstützen des Werkstücks „über Kreuz“, d. h. das Halten

des Werkstücks mit der linken Hand auf der rechten Seite

des Sägeblatts und umgekehrt, ist sehr gefährlich.

uGreifen Sie beim Entfernen von Holzabfällen oder aus

anderen Gründen mit den Händen auf beiden Seiten

des Sägeblatts nicht näher als 100 mm hinter die

Schutzabdeckung, während das Sägeblatt dreht.

Die unmittelbare Nähe des drehenden Sägeblatts ist unter

20

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

Umständen nicht für Sie erkennbar und kann zu schweren

Verletzungen führen.

uUntersuchen Sie das Werkstück vor dem Schneiden.

Wenn das Werkstück bogenförmig oder gekrümmt

ist, spannen Sie es mit der nach außen gebogenen

Fläche in Richtung des Anschlags ein. Stellen Sie

immer sicher, dass es entlang der Schnittlinie keinen

Spalt zwischen Werkstück, Anschlag und Tisch gibt.

Bogenförmige oder gekrümmte Werkstücke können

verdrehen oder verrutschen und dazu führen, dass das

Sägeblatt beim Schneiden verklemmt. Daher dürfen sich

keine Nägel oder anderen Fremdkörper im Werkstück

benden.

uVerwenden Sie die Säge nicht, bis alle Werkzeuge,

Hölzer, Abfälle, usw. vom Tisch entfernt wurden, mit

Ausnahme des Werkstücks. Kleine Rückstände, lose

Holzstücke oder andere Objekte können bei Kontakt

zum drehenden Sägeblatt mit hoher Geschwindigkeit

weggeschleudert werden.

uSchneiden Sie immer nur jeweils ein Werkstück.

Übereinander gestapelte Werkstücke können nicht

angemessen eingespannt oder xiert werden und können

beim Schneiden verrutschen oder zum Blockieren des

Sägeblatts führen.

uStellen Sie vor der Nutzung sicher, dass

die Gehrungssäge auf einer ebenen, festen

Arbeitsoberächemontiertbzw.positioniertist. Eine

ebene und feste Arbeitsoberäche verringert das Risiko,

dass die Gehrungssäge instabil wird.

uPlanen Sie Ihre Arbeit. Wenn Sie den Gehrungswinkel

ändern, stellen Sie stets sicher, dass der einstellbare

Anschlag korrekt eingestellt ist, um das Werkstück

zu stützen und dieser das Sägeblatt oder die

Schutzvorrichtung nicht blockiert. Bewegen Sie das

Sägeblatt, ohne das Werkzeug auf „ON (EIN)“ zu schalten

und ohne ein Werkstück auf dem Tisch, durch einen

vollständigen simulierten Schnitt, um sicherzustellen, dass

es keine Blockaden gibt oder Gefahr besteht, dass der

Anschlag getroffen wird.

uStellen Sie für Werkstücke, die breiter oder länger

als der Tisch sind, eine angemessene Stütze bereit,

beispielsweise Tischverlängerungen, Sägeböcke,

usw. Werkstücke, die länger oder breiter als der Tisch

der Gehrungssäge sind, können bei unsachgemäßer

Abstützung abkippen. Wenn das abgetrennte

Holzstück oder Werkstück abkippt, kann es die untere

Schutzvorrichtung anheben oder durch das drehende

Sägeblatt weggeschleudert werden.

uVerwenden Sie keine Personen als Ersatz für

Tischverlängerungen bzw. als zusätzliche Stütze.

Unzureichende Unterstützung des Werkstücks kann

dazu führen, dass Sägeblatt oder Werkstück beim

Schneidvorgang verklemmen oder verrutschen, so dass

Sie und der Helfer in das drehende Sägeblatt gezogen

werden.

uDas abgetrennte Teil darf nicht blockiert oder

anderweitig gegen das drehende Sägeblatt gedrückt

werden. Wenn kein Platz mehr vorhanden ist, z. B. durch

einen Längenanschlag, könnte sich das abgetrennte

Holzstück am Sägeblatt verkeilen und gewaltsam

weggeschleudert werden.

uVerwenden Sie stets Schraubklemmen oder

Vorrichtungen, die zum ordnungsgemäßen Abstützen

von Stangen oder Rohren konzipiert sind. Stangen

tendieren dazu, beim Schneiden wegzurollen, wodurch

sich das Sägeblatt „festbeißt“ und das Werkstück und Ihre

Hand in das Sägeblatt einzieht.

uLassen Sie das Sägeblatt die volle Drehzahl erreichen,

bevor Sie es in Kontakt mit dem Werkstück bringen.

Dadurch wird das Risiko verringert, dass das Werkstück

weggeschleudert wird.

uWenn Werkstück oder Sägeblatt blockiert werden,

schalten Sie die Gehrungssäge aus. Warten Sie, bis

alle beweglichen Teile vollständig zum Stillstand

gekommen sind, ziehen Sie den Stecker aus der

Steckdose, und/oder entfernen Sie das Akkupack.

Dann können Sie die Blockade entfernen. Das

Fortsetzen des Sägevorgangs mit verklemmtem

Werkstück kann zum Kontrollverlust und Schäden an der

Gehrungssäge führen.

uWenn der Schnitt abgeschlossen ist, lassen Sie den

Schalter los. Halten Sie den Sägekopf nach unten

und warten Sie, bis das Sägeblatt stoppt, bevor Sie

das abgetrennte Holzstück entfernen. Das Greifen mit

der Hand in die Nähe des drehenden Sägeblatts ist sehr

gefährlich.

Zusätzliche Sicherheitshinweise für

Gehrungssägen

uHalten Sie den Griff fest, wenn Sie einen

unvollständigen Schnitt machen oder den Schalter

loslassen, bevor der Sägekopf komplett in der unteren

Stellung ist. Die Bremswirkung der Säge kann dazu

führen, dass der Sägekopf plötzlich nach unten gezogen

wird; das stellt ein Verletzungsrisiko dar.

uDie bestimmungsgemäße Verwendung ist in dieser

Betriebsanleitung beschrieben. Die Verwendung von

Zubehör- oder Anbauteilen, die nicht in dieser Anleitung

empfohlen werden, sowie die Bedienung des Geräts in

Abweichung von den in dieser Anleitung beschriebenen

Verfahren können zu Verletzungen und/oder Sachschäden

führen.

uVerwenden Sie keine gebrochenen/verbogenen/

beschädigten/verformten Sägeblätter.

uErsetzen Sie abgenutzte Schlitzplatten.

La page charge ...

BLACK+DECKER BES710 Le manuel du propriétaire

Ce manuel convient également à

BLACK+DECKER BES710 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents