Monogram ZIF241NBRII Guide d'installation

INSTALLATION

INSTRUCTIONS

18”, 24” and 30” Built-In Column Freezers

24” and 30” Built-In Column Refrigerators

ENGLISH/FRANÇAIS/ESPAÑOL.

MONOGRAM.COM

2

31-1000190 Rev. 2

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for

local inspector’s use. Observe all governing codes and

ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately

contact your dealer or builder.

Skill Level – Installation of this unit requires basic

mechanical, carpentry and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the Monogram Warranty. See the Owner’s Manual for

warranty information.

Safety Information

For Monogram local service in your area, visit monogram.com.

For Monogram service in Canada, visit monogram.ca.

For Monogram Parts and Accessories, visit monogram.com.

For Monogram Parts and Accessories in Canada, visit monogram.ca.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping

forward which could result in death or serious injury. Read and follow the entire installation instructions for

securing the appliance with the anti-tip system.

WARNING

Fire or Explosion Hazard.

Keep flammable materials and vapors away from appliance. Failure to do so can result in fire, explosion,

or death.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to

have access to small parts during the installation of this product.

CAUTION

Lifting Hazard

This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance,

3 people are required for proper installation.

CAUTION

Keep fingers out of the “pinch point” areas; clearances between the doors and between the

doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately discontinue use of a damaged supply cord.

If the supply cord is damaged it must be replaced by a

qualified service professional with an authorized service

part from the manufacturer.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the unit.

This appliance must be installed with a means in the fixed

house wiring or circuit breaker for disconnecting the appli-

ance from the electrical supply after installation.

3

31-1000190 Rev. 2

Contents

Safety 2

Design Guide

Dimensions and Clearances 4

Accessories/Kits 5

Reversing the Door Swing 6

Step 1. Remove Upper Enclosure 7

Step 2. Remove Door 7

Step 3. Move Control Assembly 8

Step 4. Move Light Switch Housing 8

Step 5. Reinstall Hinge Brackets 9

Step 6. Reinstall the Enclosure 9

Step 7. Reinstall the Front Access Cover 10

Step 8. Remove Hinges from Door 10

Step 9. Panel Brackets and Hinges 11

Step 10. Reinstall the Door 11

Instructions for Dual Integrated Installation 12

The Installation Space 13

Tools, Hardware, Materials 14

Grounding the Unit 15

Flooring 15

Step 1. Remove Packaging 15

Step 2. Install Water Line 16

Step 3. Preparing Unit for Installation 16

Step 4. Install Anti-tip Bracket 17

Step 5. Joining Dual Installed Units 18

Step 6. Connecting Water Supply 19

Step 7. Inserting/Securing into Cabinet Surround 19

Step 8. Level Unit 20

Step 9. Final External Unit Preparation 21

Step 10. Toe Kick Installation 22

Step 11. Internal Unit Preparation 22

Step 12. Start Icemaker 22

Step 13. Install AutoFill Pitcher Assembly 23

Instructions for Dual Retro-Fit Installation 24

The Installation Space 25

Tools, Hardware, Materials 26

Grounding the Unit 26

Flooring 26

Step 1. Remove Packaging 27

Step 2. Install Water Line 27

Step 3. Preparing Unit for Installation 28

Step 4. Install Anti-tip Bracket 29

Step 5. Joining Dual Installed Units 30

Step 6. Connecting Water Supply 32

Step 7. Inserting/Securing into Cabinet Surround 33

Step 8. Level Unit 34

Step 9. Final External Unit Preparation 34

Step 10. Toe Kick Installation 36

Step 11. Internal Unit Preparation 36

Step 12. Start Icemaker 36

Step 13. Install AutoFill Pitcher Assembly 37

Instructions for Single Integrated Installation 38

The Installation Space 39

Tools, Hardware, Materials 40

Grounding the Unit 40

Flooring 40

Step 1. Remove Packaging 41

Step 2. Install Water Line 41

Step 3. Preparing Unit for Installation 42

Step 4. Install Anti-tip Bracket 42

Step 5. Connecting Water Supply 42

Step 6. Inserting/Securing into Cabinet Surround 43

Step 7. Level Unit 44

Step 8. Final External Unit Preparation 44

Step 9. Toe Kick Installation 45

Step 10. Internal Unit Preparation 45

Step 11. Start Icemaker 45

Step 12. Install AutoFill Pitcher Assembly 46

Stainless Steel Door Panel Installation 47

Step 1. Install Stainless Panel 48

Step 2. Adjust Stainless Panel 49

Step 3. Install Hinge Covers 49

Step 4. Install Door Trims 50

Custom Overlay Door Panel Installation 51

Custom Handle Design Guide 52

3/4” Custom Decorative Panel Dimensions 52

Step 1. Overlay Panel Prep 53

Step 2. Install Overlay Panel 54

Step 3. Adjust Overlay Panel 54

Step 4. Install Hinge Covers 55

Step 5. Install Door Trims 55

4

31-1000190 Rev. 2

Design Guide

DIMENSIONS AND CLEARANCES

Dimensions in parentheses are in centimeters.

Product Clearances

These units are equipped with a 2-position door stop.

The factory set 115° door swing can be adjusted to 90°

if clearance to adjacent cabinets or walls is restricted.

For a 90° door swing, allow 4” (10.2 cm) minimum

clearance to a wall.

When installed in a corner, allow 15” (38.1 cm) for a full

115° door swing on 18” and 24” models. Allow 16 1/2”

(41.9 cm) on 30” models.

Shipping height.

The product can be adjusted to fit into a cutout that is

84” (213.36 cm). Use leveling legs and wheels for a

maximum 1” (2.54 cm) height adjustment.

Overall Dimensions

FRONT VIEW SIDE VIEW

83-3/8"

(211.77)

C

83-1/4"

(211.46)

A

D

4"

(10.16)

TOP VIEWS

DOOR OPEN 90

DIMENSIONS BASED ON HANDLE

HEIGHT OF 2-9/16” (6.5)

Û DOOR OPEN 115Û

E

F

B

5-1/8"

(13.0)

Minimum

to a Wall

B

15"

(38.1)

Minimum

to a Wall

(16-9/16"

(42.1)

on 30” models)

Dimensions 18” Models 24” Models 30” Models

A Overall Width - Front 17-1/2” (44.5 cm) 23-1/2” (59.7 cm) 29-1/2” (74.9 cm)

B Overall Width - Rear 17-1/4” (43.8 cm) 23-1/4” (59.1 cm) 29-1/4” (74.3 cm)

C Overall Depth 24-3/4” (62.9 cm) 24-3/4” (62.9 cm) 24-3/4” (62.9 cm)

D Case Depth 22-1/16” (56 cm) 22-1/16” (56 cm) 22-1/16” (56 cm)

E Door Clearance at 90° 21-1/4” (53.9 cm) 27-1/4” (62.9 cm) 33-1/4” (84.5 cm)

F Door Clearance at 115° 19-1/16” (48.4 cm) 24-1/2” (62.2 cm) 29-15/16” (76.0 cm)

Cutout Width 17-13/16” (45.3 cm) 23-13/16” (60.5 cm) 29-13/16” (75.7 cm)

Cutout Height 84” (213.4 cm) 84” (213.4 cm) 84” (213.4 cm)

Cutout Depth 25” (63.5 cm) 25” (63.5 cm) 25” (63.5 cm)

Weight 370 lbs

(167.8 kg)

460 lbs (208.7 kg)

(Refrigerator)

430 lbs. (195.0 kg)

(Freezer)

495 lbs (224.5 kg)

(Refrigerator)

475 lbs. (215.5 kg)

(Freezer)

5

31-1000190 Rev. 2

Design Guide

7KH0RQRJUDP&ROXPQVUHIULJHUDWRUVDQGIUHH]HUVFDQEHLQVWDOOHGLQPDQ\FRQ¿JXUDWLRQVZLWKGLႇHUHQWLQVWDOODWLRQ

situations. Three installation situations will be explained along with door reversal instructions and two options for door

panel installation.

Reversing the Door Swing (all installation types)

Making a refrigerator LH swing and freezer RH swing. MUST be done BEFORE the unit is removed from the ship-

ping skid.

Instructions for Dual Integrated Installation

New construction installation with 25” deep openings

Instructions for Dual Retro Installation

Existing construction installation (existing cutouts) with 24” deep openings that are 41-1/2” or 47-1/2” wide

Instructions for Single Integrated Installation

New construction installation with 25” deep opening

Instructions for Stainless Steel Door Panel Installation (all installation types)

Installing Stainless Steel Door Panel Kits

Instructions for Custom Overlay Door Panel Installation (all installation types)

Installing Custom Decorative Panels

ACCESSORIES/KITS

ŶZKUN+HDWHU8QL¿FDWLRQ.LW

Ŷ WX08X10006 8 Ft. Water Line

Ŷ ZKR42N 42” Trim Retro Kit

Ŷ ZKR48N 48” Trim Retro Kit

Ŷ 6WDLQOHVV6WHHO'RRU3DQHO.LWV

Ŷ 6WDLQOHVV7RH.LFNVIRU'XDO,QVWDOO

ZK1SN189NLH LH 18” Stainless Steel Door Panel

ZK1SN184NRH RH 18” Stainless Steel Door Panel

ZK1SN249NLH LH 24” Stainless Steel Door Panel

ZK1SN244NRH RH 24” Stainless Steel Door Panel

ZK1SN309NLH LH 30” Stainless Steel Door Panel

ZK1SN304NRH RH 30” Stainless Steel Door Panel

ZKSP1H1CNSS Minimalist Handle for Stainless

Steel Panels Only

ZKSP1H1PNSS Statement Handle for Stainless

Steel Panels Only

42” ZKK42P

48” ZKK48P

54” ZKK54P

60” ZKK60P

6

31-1000190 Rev. 2

Reversing the Door Swing

This step can be done for all installation types.

7

31-1000190 Rev. 2

Installation Instructions - Reversing the Door Swing

STEP 2 REMOVE DOOR

Ŷ Open the door to the open position.

Ŷ Have a second person support the open door.

Ŷ Remove 2 T30 Torx screws securing the bottom

hinge to the case.

Ŷ Remove the 2 T30 Torx screws securing the top

hinge to the case.

Ŷ Place the door on a protected work surface (to

prevent scratches), liner side down.

NOTICE: Door hinges will remain in the open position

during the door reversal procedure.

STEP 1 REMOVE UPPER

ENCLOSURE

Ŷ Open the front cover of

the enclosure to 90°.

Locate filter and filter

removal tool. Filter

should be as shown.

Ŷ5RWDWH¿OWHUóWXUQ

counterclockwise

XVH¿OWHUUHPRYDOWRROLI

needed).

Ŷ3XOO¿OWHUWRZDUG\RXWR

remove. NOTE: Water

V\VWHPZLOOQRWIXQFWLRQZLWKRXW¿OWHULQSODFH

Ŷ Remove 6 screws securing front enclosure to top case.

WARNING

Follow all steps when reversing the

door swing. Failure to follow these instructions, leaving

off parts, or overtightening screws, can lead to the door

falling off and result in injury and property damage.

WARNING

Door Hinge Pinch

Point Hazard

Door hinges are under tension and should be left in the

open position throughout the reversal process. Closing

the hinge can lead to a finger pinch point hazard.

Ŷ If installation will require the door swing to be reversed,

follow these directions to reverse the door swing

BEFORE the unit is removed from the shipping skid.

Ŷ Instructions for reversing a RH swing refrigerator are

shown in the following steps.

WARNING

Tip Over Hazard.

This appliance is top heavy, especially with the door

open, and must be secured to prevent tipping forward

which could result in death or serious injury.

Screws

1/4” Hex Screws

Filter Removal Tool

Filter

Mounting

Hook

Compartment Door

8

31-1000190 Rev. 2

Installation Instructions - Reversing the Door Swing

STEP 3

MOVE CONTROL ASSEMBLY

Ŷ Remove upper hinge brackets by removing the T-30

Torx screws.

Ŷ Remove the

Phillips head

screw from the

middle of the

housing on the

hinge side.

Ŷ Insert a flat head screwdriver or putty knife between

the glass front and plastic side and free the control

assembly by prying the plastic pins clear of the side

bracket holes.

Ŷ Lay the glass assembly on top of the control housing.

Ŷ Remove 4 screws, 2 on each end, to remove the

housing assembly using a 1/4” Hex bit.

Ŷ Move the housing assembly to the opposite side and

install using the 4 screws, 2 on each side.

NOTE: Make sure wires do not get pinched. On 18”

models, the red/white/black 5-pin wire connector

will need to be removed from the control board and

routed through the opposite corner bracket and

reconnected to the

control board to

prevent pinching

the wiring.

STEP 3

MOVE CONTROL ASSEMBLY

(Cont.)

Ŷ Snap glass assembly back onto the control housing

assembly, ensuring plastic pins snap into holes on

the side of the housing.

STEP 4 MOVE LIGHT SWITCH

HOUSING

Ŷ Remove front access cover from unit by removing

two 1/4” hex head screws.

Ŷ Remove the Philip screw first and lower hinge

brackets by removing three T-30 Torx screws.

Ŷ Remove screw with 1/4” hex bit driver at the bottom

corner of light switch housing.

Plastic Pins

(Both sides)

Screw

5-pin wire connector

Wires must be rerouted from one

side to the other for 18” models.

Access Cover

1/4” Hex Head

Screws

Upper Hinge

Bracket

T-30 Torx screws

Phillips Screw

T-30 Torx Screws

Phillips Screw

Light Switch

9

31-1000190 Rev. 2

Installation Instructions - Reversing the Door Swing

STEP 5 REINSTALL HINGE

BRACKETS

Ŷ Move top hinge bracket to bottom and bottom bracket

to top.

Ŷ Ensure the 2 rectangular slots of bracket are on

outside, hinge side of case.

Ŷ Install both brackets with 3 T-30 Torx screws 45 in/lb

(5.1 Nm).

Ŷ Install the Phillips screw.

Ŷ Start 2 screws in

each bracket for

hinge mounting

but do not tighten

all the way.

STEP 6 REINSTALL THE

ENCLOSURE

Ŷ Install the enclosure assembly with removed six 1/4”

hex head screws.

Ŷ

Locate blue arrow on filter. Rotate filter to align arrow

as shown.

Rectangular

Slots

Screws for

Hinge Brackets

Housing Key Holes

STEP 4 MOVE LIGHT SWITCH

HOUSING (Cont.)

Ŷ Move the mounting bracket to the other side of the

unit by removing two Philips screws and using them

to install the bracket in its new location.

Ŷ Slide housing forward and down to remove from case

and grommets on case bottom.

Ŷ Keeping it connected to the unit, lay housing aside.

Ŷ Remove 2 grommets with Phillips driver.

Ŷ Move grommets to the set of 2 holes on opposite

side.

Ŷ Align housing key holes over grommets and then

slide back until engaged. Ensure wires do not get

pinched.

Ŷ Install Phillips screw into bottom hole to hold in place.

Grommets

Mounting

Bracket and

Screws

Phillips Screw

1/4” Hex Screws

10

31-1000190 Rev. 2

Installation Instructions - Reversing the Door Swing

STEP 8 REMOVE HINGES FROM

DOOR

Ŷ Remove 3 screws securing each hinge from the top

and bottom of the door and one screw securing the

support bracket to the door (T-30 Torx)

Ŷ Move the hinge assembly to the opposite end of the

door - top hinge to the bottom and bottom hinge to

the top. Hinge, L-bracket already attached to hinge,

and support bracket will all move together.

Ŷ 2 shims between the hinge bracket and door will

be moved to the other side -

save for installing the hinge.

WARNING

Door Hinge Pinch

Point Hazard

Door hinges are under tension and should be left in

the open position throughout the reversal process.

Closing the hinge can lead to a finger pinch point

hazard.

Hinge

Support

Bracket

Shims

STEP 6 REINSTALL THE

ENCLOSURE (Cont.)

Ŷ,QVHUW¿OWHULQWRSRVLWLRQDQGURWDWHóWXUQFORFNZLVH

XVH¿OWHUUHPRYDOWRROLIQHHGHG

Ŷ5HWXUQ¿OWHUUHPRYDOWRROWRPRXQWLQJKRRN

Ŷ

Close the compartment door.

STEP 7 REINSTALL THE FRONT

ACCESS COVER

Ŷ Put the access cover back onto the unit and secure

with two 1/4” hex head screws.

Ŷ Verify the two 1/4” hex head screws are assembled

to handle side of the products for both freezer and

fresh food columns.

1/4” Hex Screws

Access

Cover

1/4” Hex

Screws

11

31-1000190 Rev. 2

Installation Instructions - Reversing the Door Swing

STEP 9 PANEL BRACKETS AND

HINGES

Ŷ Remove panel brackets on each end of the door by

removing the T30 Torx screws.

Ŷ Slide same bracket on each end to other side of door

and re-install brackets to door.

Ŷ Install hinges to door ensuring that 2 shims are

between hinge L-bracket and door. Install with 3 T-30

Torx screws 45 in/lb (5.1 Nm)

NOTE: Ensure L-bracket remains attached to hinge

and is on the outer side of the door. Hinge is on the

inner door side.

REMINDER: Hinges have to move from top to bottom

and bottom to top.

Ŷ Install support bracket screw through both support

bracket and panel bracket.

STEP 10 REINSTALL THE DOOR

Ŷ Ensure 2 hinge screws are started but not tightened

in hinge brackets on case.

Ŷ With 2nd person, hold door with hinges near correct

position.

Ŷ Install top hinges with key hole over screws and slide

bracket.

Ŷ Repeat on bottom.

NOTE: Ensure 2 tabs on hinges are inserted into

the rectangular slots on outside of hinge brackets

BEFORE tightening screws.

Ŷ Tighten bottom screws 45 in/lb (5.1 Nm).

Ŷ Tighten top screws 45 in/lb (5.1 Nm).

Ŷ Carefully ensure door closes correctly and gasket

aligns with case.

WARNING

Follow all steps when reversing

the door swing. Failure to follow these instructions,

leaving off parts, or overtightening screws, can

lead to the door falling off and result in injury and

property damage.

Hinge

Support

Bracket

Shims

Tabs in

rectangular slots

Key hole slot

over screws

12

31-1000190 Rev. 2

Instructions for Dual Integrated Installation

New construction installation with 25” deep openings

13

31-1000190 Rev. 2

Design Guide - Dual Integrated Installation

18” Integrated Freezer

24” Integrated Refrigerator

30” Integrated Freezer

30” Integrated Refrigerator

DUAL INTEGRATED INSTALLATION SPACE

Dimensions in parentheses are in centimeters.

FRONT VIEW

84"

(213.4)

41 1/2" (105.4)

E

W

7 1/2”

(19.1)

4"

(10.2)

6"

(15.24)

6"

(15.24)

2 1/2"

(6.4)

3 1/2"

(8.9)

4 1/8"

(10.5)

2"

(5.1)

ELEC W

4"

(10.2)

2 1/2"

(6.4)

5"

(12.7)

22 1/8" (56.2)

27 1/4"

(69.2)

SIDE VIEW

25" (63.5)

3 1/2"

(8.9)

Finished

Return

Back

FRONT VIEW

84"

(213.4)

47 1/2"

(120.7)

E

W

7 1/2"

(19.1)

4"

(10.2)

2 1/2"

(6.4)

2 1/2"

(6.4)

3 1/2"

(8.9)

4 1/8"

(10.5)

2"

(5.1)

ELEC W

6 1/4"

(10.2)

5"

(12.7)

22 1/8" (56.2)

28" (71.1)

SIDE VIEW

25" (63.5)

3 1/2"

(8.9)

Finished

Return

Back

6"

(15.24)

6"

(15.24)

FRONT VIEW

84"

(213.4)

47 1/2"

(120.7)

ELEC W

9 1/2"

(24.1)

4

4 3/8"

(11.1)

ELEC W

4"

(10.2)

2 1/2"

(6.4)

2 1/2"

(6.4)

5"

(12.7)

5"

(12.7)

28 1/8" (71.4)

33 1/4" (84.5)

SIDE VIEW

25" (63.5)

3 1/2"

(8.9)

Finished

Return

Back

6"

(15.24)

6"

(15.24)

84"

FRONT VIEW

84"

(213.4)

53 1/2" (134.6)

ELEC W

9 1/2"

(24.1)

4"

(10.2)

4 3/8"

(11.1)

ELEC W

6 1/4"

(15.9)

2 1/2"

(6.4)

5"

(12.7)

2 1/2"

(6.4)

5"

(12.7)

28 1/8" (71.4)

34" (86.4)

25

SIDE VIEW

25" (63.5)

3 1/2"

(8.9)

Finished

Return

Back

6"

(15.24)

6"

(15.24)

84"

FRONT VIEW

84"

(213.4)

59 1/2" (151.3)

ELEC W

9 1/2"

(24.1)

4"

(10.2)

4 3/8"

(11.1)

ELEC W

6 1/4"

(15.9)

2 1/2"

(6.4)

5"

(12.7)

2 1/2"

(6.4)

5"

(12.7)

34 1/8" (86.67)

40" (101.6)

25

SIDE VIEW

25" (63.5)

3 1/2"

(8.9)

Finished

Return

Back

6"

(15.24)

6"

(15.24)

18” Integrated Freezer

30” Integrated Refrigerator

24” Integrated Freezer

24” Integrated Refrigerator

24” Integrated Freezer

30” Integrated Refrigerator

14

31-1000190 Rev. 2

Design Guide - Dual Integrated Installation

DUAL INTEGRATED INSTALLATION SPACE

Water And Electrical Locations

Electrical and water supply must be located as shown.

The Cutout Depth Must Be 25”

Cutout is based on installation of 2 products with a left-

and-right hand door swing.

Heater Unification Kit ZKUN required.

Product Clearances

These units are equipped with a 2-position door stop.

The factory set 115° door swing can be adjusted to 90°

if clearance to adjacent cabinets or walls is restricted.

For a 90° door swing, allow 4” (10.2 cm) minimum

clearance to a wall.

When installed in a corner, allow 15” (38.1 cm) for a full

115° door swing on 18” and 24” models. Allow 16.5”

(41.9 cm) on 30” models.

Additional Specifications

• A separate 115 volt 60Hz., 15 or 20 amp power supply

is recommended for each product. An individual

properly grounded branch circuit or circuit breaker is

recommended. Install a properly grounded 3-prong

electrical receptacle recessed into the back wall.

Electrical must be located on rear wall as shown.

• Water line must be located on the back wall as shown.

The water line should be 1/4” O.D. copper tubing or

QuickConnect

™

kit (WX08X10006) between the cold

water line and water connection location, long enough

to extend to the front of the unit (8’ [2.4m]). Installation

of an easily accessible shut-off valve in the water line

is required.

• A minimum of 3-1/2” finished return matching cabinet

exterior is recommended on interior on all sides and

top at front of opening.

TOOLS AND MATERIALS REQUIRED

• Metal shears

• #1, #2 Phillips screwdriver

• Flathead screwdriver

• Putty knife

• Measuring tape

• Drill and 1/16”, 5/64”, 3/16”, 1/2” bits

• 5/32” concrete bit (if installing anti-tip into concrete)

• 1/4”, 3/8”, 7/16” driver/socket

• 7/16” open wrench

• T20, T30 driver/bit

• 1/8”, 1/4” hex driver (allen wrench)

• Level

• Water shut-off valves (optional but recommended)

• 8’ waterline (one per unit requiring water hookup)

• Masking tape

• Rubbing alcohol

• Adjustable wrench

• Center punch

• Heater Unification Kit (ZKUN)

• Stainless Steel Door Kits (if applicable)

• Custom panels for doors (if applicable)

• Handle Kits (if applicable)

• Small Ratchet

REFRIGERATOR/FREEZER LOCATION

Ŷ Do not install the refrigerator/freezer where the tem-

perature will go below 55°F (13°C). It will not run

often enough to maintain proper temperatures.

Ŷ Do not install the refrigerator/freezer where

temperatures will go above 100°F (37°C). It will not

perform properly.

Ŷ Do not install the refrigerator/freezer in a location

exposed to water (rain, etc.) or direct sunlight.

Ŷ Install it on a floor strong enough to support it fully

loaded.

HARDWARE SUPPLIED (per unit)

• Water Filter Bypass Plug (if equipped)

• Air filter (if equipped)

• Anti-Tip bracket

• 3 Lag screws

• 3 Tapcon screws

• 3 Toggles with bolts

• 1 Hair Pin Cotter

• 1 Retaining pin

• Panel installation templates

• 2 Door trims

• 2 Door panel brackets

• Set screws

• #6 Phillips head wood screws

• Door Bracket Cover Top

• T30 screws

• 1 Hinge limiter pin

• Center door panel bracket

• Hi-Lo screw and square washer

• Access Cover

• Painted access cover screws

15

31-1000190 Rev. 2

Installation Instructions - Dual Integrated Installation

FLOORING

For proper installation, this product must be placed

on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should

be strong enough to support a fully loaded refrigerator

or freezer, or approximately 1,200 lbs. per unit.

NOTE: Protect the finish of the flooring.

NOTE: Not recommended for installation on carpeted

flooring.

GROUNDING THE UNIT

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall receptacle to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR

REMOVE THE THIRD (GROUND) PRONG

FROM THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO

CONNECT THE REFRIGERATOR TO A

2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD

WITH THIS APPLIANCE.

WARNING

Electrical Shock

Hazard. Failure to follow these instructions can

result in death, fire, or electrical shock.

STEP 1 REMOVE PACKAGING

Ŷ Remove outer carton and external packing from units.

Ŷ Inspect for damage.

Ŷ If installation will require the door swing to be

reversed, follow the instructions in Reversing the

Door Swing section to reverse the door swing

BEFORE the unit is removed from the shipping skid.

Ŷ Ensure the flooring that the units are set is clean/

free of debris that could be collected on to, or

pinched in front of the wheels and damaging the

floor. Additionally, it is recommended that the floor

be protected with a plastic covering through out the

installation process.

Ŷ Remove hardware kit from top drawer.

Ŷ If installation requires a 90° door opening, the hinge

limiter pin must be installed in the

top hinge BEFORE the unit is

removed from the shipping skid.

Pin is located in the hardware kit.

- Open the door approximately

45°, but no wider than 90°, to

expose the hole in the back

hinge bracket and install the

limiting pin. Pin must be fully

seated in the bracket or the door will not close

properly.

Ŷ Remove front access cover from unit by removing

two 1/4” hex head screws. (Some models have

access cover in a box on the left side of the cabinet.)

Place the cover and screws to the side for future

installation.

Ŷ Remove three 3/8” drive screws and two 7/16” drive

screws from each side of the unit to release it from

the shipping skid. Tip the unit from the side enough

to remove the shipping material from under the unit,

but above the shipping skid (both sides)

Ŷ CAREFULLY roll the unit off the back side of the

shipping skid.

Ŷ Handle from side only with a hand truck.

Shipping

Bracket

7/16” Drive

Screws

3/8” Drive

Screws

1/4” Hex Head

Screws

Top

Hinge

WARNING

Tip Over Hazard. This

appliance is top heavy. Use extreme caution with

moving to prevent tipping over which could result in

death or serious injury.

16

31-1000190 Rev. 2

Installation Instructions - Dual Integrated Installation

STEP 2 INSTALL WATER LINE

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the

line of water.

ŶInstall a shut-off valve between the water valve and

cold water pipe in a basement or cabinet. The shut-

off valve should be located where it will be easily

accessible.

ŶTurn on the main water supply and flush debris.

Run about a quart of water through the tubing into a

bucket. Shut off water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are included in

many water supply kits. Before purchasing, make sure

a saddle type valve complies with your local plumbing

codes.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle

valves are illegal and use is not permitted in

Massachusetts. Consult with your licensed plumber.

Ŷ Route 1/4” OD copper or SmartConnect

™

(WX08X10006) plastic tubing between house cold

water line and the water connection location at the

front of the unit.

SmartConnect

™

Refrigerator Tubing Kits are

available. One 8’ (2.4m) water line (WX08X10006) is

needed for each unit. The waterline(s) will be taped

to the floor using masking tape after anti-tip bracket

installation.

Ŷ Tubing should be long enough to extend to the front

of the unit. Allow enough tubing to accommodate

bend leading into the water line connection. Unit

must be tipped on its side to route waterline

underneath and to the front of the appliance.

NOTE: The only GE Appliances approved plastic

tubing is supplied in the SmartConnect

™

Refrigerator

Tubing kits. Do not use any other plastic water supply

line because the line is under pressure at all times.

Other types of plastic may crack or rupture with age

and cause water damage to your home.

WARNING

Connect to potable water supply

only. A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 psi (275-827 kilopascals).

STEP 3 PREPARING UNIT FOR

INSTALLATION

Ŷ Place the right hand unit in front of the installation

opening in a way that the unit is in front of the

intended installed location.

Ŷ Unpack the heater Unification Kit (ZKUN) and make

sure all of the components on the list are included.

Ŷ Install adhesive heater on the outside of the unit to

the left side of the case. Install heater 4” below the

case top. Heater should be centered front to back on

the metal case. Ensure the heater connector cord is

toward the top of the unit when installed.

Clips

Adhesive

Heater

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO

NOT drill into the refrigerator.

17

31-1000190 Rev. 2

Installation Instructions - Dual Integrated Installation

STEP 4

INSTALL ANTI-TIP BRACKET

(Cont.)

Ŷ Measure and mark from the RH side of the opening

per the table above depending on the size of the RH

unit you are installing.

Ŷ Measure and mark again from the RH side of

the opening per the table and depending on your

combination of LH and RH units.

For example, if installing an 18” LH unit and a 30” RH

unit, use 5-3/4” and 38-5/8”.

Ŷ Mount the anti-tip bracket centered about the marks

and flush to the floor as shown. Mark 3 holes for wall

mounting or 4 holes for floor mounting.

WOOD MOUNTING: Predrill with 3/16” drill bit, 2”

deep, then install lag bolts with a 7/16” driver.

CONCRETE MOUNTING: Predrill with a 5/32”

concrete bit, 2” deep, then install

tapcon screws with a 7/16” driver.

STEEL MOUNTING: Predrill with a

1/2” drill bit, insert toggle, then install

bolts with a 7/16” driver.

The bracket must be screwed to

either the FLOOR or REAR WALL.

Ŷ

If the enclosure is deeper than 25 ½”, the anti-tip

bracket should be secured to the floor 25” from front

of the enclosure.

Ŷ Tape the waterline to the wall and floor approximately

3” to the left of the anti-tip bracket. Apply tape about

every 5” toward the front of the opening (tape will

prevent the unit from rolling over the waterline during

installation). Do not tape near the cabinet front in

order to keep tape hidden under the unit.

LH Unit

RH Unit

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

Read and follow the entire installation instructions

for securing the appliance with the anti-tip system.

3"

5"

3"

5"

STEP 4

INSTALL ANTI-TIP BRACKET

Ŷ Remove the anti-tip bracket from the hardware kit.

Ŷ Anti-tip bracket should be mounted against the back

wall or up to 25-1/2” (64.7 cm) maximum from front of

opening. Use floor mounting method if the bracket is

not against a wall (bracket hardware is provided for

mounting into wood, steel studs and concrete).

LH Unit

RH UNIT

18” 24” 30”

26-5/8”

67.6 CM

23-1/2’

59.6 CM

23-1/2”

59.7 CM

8-7/8”

22.5 CM

18”

32-5/8”

67.6 CM

29-1/2”

59.7 CM

29-1/2”

59.7 CM

5-3/4”

22.5 CM

24

38-5/8”

67.6 CM

35-1/2”

59.7 CM

35-1/2”

59.7 CM

5-3/4”

22.5 CM

30

STEP 3 PREPARING UNIT FOR

INSTALLATION (Cont.)

Ŷ Install the transformer into the case top assembly:

1. Remove cover top by removing eight #8 hex screws

and keep aside for assembling back the cover top.

2. Place the transformer into the case top provided in

ZKUN kit and secure it with the existing (1/4”) hex

screws to left front of case top.

3. Connect the 2 pin transformer connector to the

heater connector and 3 pin connector to panel

control, make sure locking tabs are engaged.

4. Verify the master switch is on.

5. Assemble the cover top with screws save from

previous step.

6. Enclosure assembly upper is hidden for clarity.

WARNING

Electrical Shock

Hazard. To avoid the risk of electric shock, make

sure the power cord is not plugged into the wall outlet.

2 Pin

Connector

to Heater

Connector

3 Pin

Connector

Transformer

Master Switch

#8 Hex

Screws

Cover Top

18

31-1000190 Rev. 2

Installation Instructions - Dual Integrated Installation

STEP 5

JOINING DUAL INSTALLED UNITS

BOTTOM BACK UNIFICATION

Ŷ Loosen the two bottom screws of rear access covers of

both units and remove the top screws.

Ŷ Hang the unification bracket to the bottom screws and

reassemble the screws at the top

Ŷ Tighten screws to tie units together.

BOTTOM FRONT UNIFICATION

Ŷ Install the bottom front unification bracket using a 3/8”

driver (4 screws).

TOP UNIFICATION

Ŷ Loosen the front two screws on top of the unit and

remove the two middle screws.

Ŷ Assemble the bracket to the front screws and reinstall

the middle screws.

Ŷ Tighten screws to tie units together.

8QL¿FDWLRQ%UDFNHW

8QL¿FDWLRQ

Bracket

8QL¿FDWLRQ

Bracket

19

31-1000190 Rev. 2

Installation Instructions - Dual Integrated Installation

STEP 6

CONNECTING WATER

SUPPLY

Ŷ Locate and bring the tubing to the front of the

cabinet.

Ŷ Turn the water on to flush debris from the line. Run

about a quart of water through the tubing into a

bucket, then shut off the water.

Ŷ Remove strain relief screw to allow for enough slack

to make a proper water connection. (Screw must be

replaced in the next step.)

Copper Tubing:

Ŷ Slip a 1/4” nut and ferrule (provided) over both ends

of the copper tubing. Insert the tube into the union

fitting on the unit and tighten the nut to the union.

Ŷ Turn on the water to check for leaks.

SmartConnect

™

Tubing:

NOTE: The only GE Appliances-approved plastic

tubing is supplied in the SmartConnect

™

Refrigerator

Tubing kits. Do not use any other plastic water supply

line because the line is under pressure at all times.

Other types of plastic may crack or rupture with age

and cause water damage to your home.

Ŷ Insert the molded end of the tubing into the

refrigerator or freezer connection. Tighten the

compression nut until it is just hand-tight.

Ŷ Follow the instructions provided with the tubing.

Overtightening can cause leaks!

Ŷ Turn on the water to check for leaks.

Freezer

Water Supply

House

Water Supply

Refrigerator/

Freezer

Water Supply

Strain Relief

Screw

STEP 7 INSERTING/SECURING

INTO CABINET SURROUND

Ŷ Plug both units into the outlet in the wall.

Ŷ Find the installation string that is attached to the door

of the unit; this is to be used as you are pushing the

unit back into the opening. The string is attached to

the power cord; as you walk the unit back into the

opening you should pull the string tight to make sure

the power cord is routed underneath the unit.

Ŷ Slowly walk both units into opening making sure not

to touch the cabinetry on the sides and top to prevent

damage. Both door faces should be 7/8” behind

the front face of surrounding cabinets on either a

stainless or custom panel installation.

Ŷ Place power cord on its edge and pull under product

between rollers and away from the anti-tip bracket to

ensure cord is not damaged during installation.

Ŷ As you walk the unit back into the opening, you

should pull the string tight to make sure the power

cord is routed underneath the unit.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with

any doors open, and must be secured to prevent

tipping forward which could result in death or

serious injury.

WARNING

Electrical Shock Hazard.

To reduce the risk of electrical shock, be careful

during the remaining installation steps not to touch

wiring or electrical components inside the compressor

compartment while the appliance is plugged in and

the front access cover is not in place.

Installation

String

Power Cord

String

WARNING

Connect to potable water supply

only. A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 psi (275-827 kilopascals).

WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO

NOT drill into the refrigerator.

20

31-1000190 Rev. 2

STEP 7 INSERTING/SECURING

INTO CABINET SURROUND (Cont.)

Ŷ Replace the waterline strain relief screw.

Ŷ Store the excess string, and water tubing under

the unit.

Installation Instructions - Dual Integrated Installation

WARNING

Electrical Shock Hazard.

Replace waterline strain relief in front rail location as

shown.

Strain Relief

Screw

STEP 8 LEVEL UNIT

All models have 4-point leveling. The front is supported

by leveling legs; the rear is supported by adjustable

wheels. Both are accessible from the front of the unit.

Ŷ To level the back of the unit, turn the 7/16” hex nut

located above the front wheels. Turn clockwise to

raise or counterclockwise to lower the unit.

Ŷ For front leveling, use a 7/16” open-end wrench.

Ŷ Adjust height of unit to match installation cutout

opening 84”. The unit should be level and plumb with

cabinetry.

NOTICE: The rear leveling wheels and front leveling

legs are limited to a maximum height adjustment of 1”.

If the installation requires more than 84” height, the

installer should elevate the unit on a sheet of plywood

or runners. Cabinetry trim could also be added across

the top of the opening to shorten the opening. If you

attempt to raise the unit more than 1”, you will damage

the front leveling legs and the rear leveling wheels.

Hex nut adjusts

rear wheels

Open-end wrench

adjusts front

leveling legs

La page charge ...

Monogram ZIF241NBRII Guide d'installation

Ce manuel convient également à

Monogram ZIF241NBRII Guide d'installation

dans d''autres langues

Documents connexes

Autres documents