Kenmore FGGS3065PB Guide d'installation

Marque: Kenmore

Modèle: FGGS3065PB

Catégorie: Micro-ondes

Taper: Guide d'installation

Ce manuel convient également à

32673

INSTALLATION INSTRUCTIONS

30" GAS SLIDE-IN RANGE

Printed in United States

Important Notes to the Installer

1. Read all instructions contained in these installation

instructions before installing range.

2. Remove all packing material from the oven and the

drawer compartments before connecting the gas and

the electrical supply to the range.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the

consumer.

5. Note: For operation at 2000 ft. elevations above see

level, appliance rating shall be reduced by 4 percent

for each additional 1000 ft.

Important Note to the Consumer

Keep these instructions with your owner's guide for

future reference.

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Table of Contents

Important Safety Instructions .......................................... 2

Product & Cabinet Dimensions....................................3-4

To Avoid Breakage .......................................................... 5

Before Starting................................................................ 6

Cabinet Construction ................................................... 6-7

Provide an Adequate Gas Supply................................... 7

Seal the Openings .......................................................... 7

Connect the Range to the Gas Supply ........................7-8

LP/Propane Gas Conversion .......................................... 8

Electrical Requirements.................................................. 8

Moving the Appliance for servicing and Cleaning ........... 8

Anti-Tip Brackets Installation ..................................... 9-10

Range Installation ..........................................................11

Leveling the Range....................................................... 12

Decorative Rear Trim Installation ................................. 12

Check Operation......................................................13-14

When All Hookups are Complete.................................. 14

Model and Serial Number Location .............................. 14

Before You Call for Service........................................... 14

If the information in this manual is not followed exactly, a re or

explosion may result causing property damage, personal injury or death.

FOR YOUR SAFETY:

— Do not store or use gasoline or other ammable vapors and liquids in

the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor's phone. Follow the

gas supplier's instructions.

• If you cannot reach your gas supplier, call the re department.

— Installation and service must be performed by a qualied installer,

service agency or the gas supplier.

P/N 809018301 (1507) Rev. A

English – pages 1-14; Spanish - pages 15-28; French – pages 29-43

Appliances Installed in the state of

Massachusetts:

This Appliance can only be installed in the state of

Massachusetts by a Massachusetts licensed plumber or

gastter.

This appliance must be installed with a three (3) foot / 36

in. long exible gas connector.

A"T" handle type manual gas valve must be installed in

the gas supply line to this appliance.

Cold temperature can damage the

electronic control. When using the appliance for the

rst time, or when the appliance has not been used

for an extended period, be certain the unit has been

in temperatures above 32°F (0°C) for at least 3 hours

before turning on the power to the appliance.

United States

Canada

Refer to your serial

plate for applicable

agency certication.

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

Installation of this range must conform with local codes

or, in the absence of local codes, with the National Fuel

Gas Code ANSI Z223.1/NFPA .54-latest edition.

This range has been design certified by CSA

International. As with any appliance using gas and

generating heat, there are certain safety precautions

you should follow. You will find them in the Use and

Care Guide, read it carefully.

• Be sure your range is installed and grounded

properly by a qualified installer or service

technician.

• This range must be electrically grounded in

accordance with local codes or, in their absence,

with the National Electrical Code ANSI/NFPA No.

70—latest edition. See Grounding Instructions.

• Air curtain or other overhead hoods, which operate

by blowing a downward air ow on to a range, shall

not be used in conjunction with gas ranges other

than when the hood and range have been designed,

tested and listen by an independent test laboratory

for use in combination with each other.

• Before installing the range in an area covered with

linoleum or any other synthetic oor covering,

make sure the oor covering can withstand heat

at least 90°F above room temperature without

shrinking, warping or discoloring. Do not install the

range over carpeting unless you place an insulating

pad or sheet of ¼" (0,64 cm) thick plywood between

the range and carpeting.

• Make sure the wall coverings around the range

can withstand the heat generated by the range.

• Do not obstruct the ow of combustion air at the

oven vent nor around the base or beneath the

lower front panel of the range. Avoid touching the

vent openings or nearby surfaces as they may become

hot while the oven is in operation. This range requires

fresh air for proper burner combustion.

Never leave children alone or

unattended in the area where an appliance is in use.

As children grow, teach them the proper, safe use of all

appliances. Never leave the oven door open when the

range is unattended.

Stepping, leaning or sitting on the

doors or drawers of this range can result in serious

injuries and can also cause damage to the range.

• Do not store items of interest to children in

the cabinets above the range. Children could be

seriously burned climbing on the range to reach items.

• To eliminate the need to reach over the surface

burners, cabinet storage space above the

burners should be avoided.

• Adjust surface burner ame size so it does not

extend beyond the edge of the cooking utensil.

Excessive ame is hazardous.

• Do not use the oven as a storage space. This

creates a potentially hazardous situation.

• Never use your range for warming or heating the

room. Prolonged use of the range without adequate

ventilation can be dangerous.

• Do not store or use gasoline or other ammable

vapors and liquids near this or any other

appliance. Explosions or res could result.

• In the event of an electrical power outage, the surface

burners can be lit manually. To light a surface burner,

hold a lit match to the burner head and slowly turn

the Surface Control knob to LITE. Use caution when

lighting surface burners manually.

• Reset all controls to the "off" position after using

a programmable timing operation.

FOR MODELS WITH SELF-CLEAN FEATURE:

• Remove broiler pan, food and other utensils

before self-cleaning the oven. Wipe up excess

spillage. Follow the precleaning instructions in the

Use and Care Guide.

• Unlike the standard gas range, THIS COOKTOP

IS NOT REMOVABLE. Do not attempt to remove the

cooktop.

• A child or adult can tip the range and

be killed.

• Verify the anti-tip device has been

installed to oor or wall as per

installation instructions.

Tip Over Hazard

• Ensure the anti-tip device is re-engaged to oor or

wall when the range is moved.

• Do not operate the range without the anti-tip device

in place and engaged.

• Failure to follow these instructions can result in

death or serious burns to children and adults.

To check if the anti-tip bracket is installed

properly, use both arms and grasp

the rear edge of range back. Carefully

attempt to tilt range forward. When

properly installed, the range should not

tilt forward.

Refer to the anti-tip bracket installation instructions

supplied with your range for proper installation.

This manual contains important safety symbols and instructions. Please pay attention to these symbols and

follow all instructions given.

This symbol will help alert you to situations that may cause serious bodily harm, death or

property damage.

This symbol will help alert you to situations that may cause bodily injury or property

damage.

IMPORTANT SAFETY INSTRUCTIONS

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

21¾

(55.25 cm)

NOTES:

1. Do not pinch the power supply cord or exible gas conduit between the range and the wall.

2. Do not seal the range to the side cabinets.

3. 24" (61 cm) minimum clearance between the cooktop and the bottom of the cabinet when the

bottom of wood or metal cabinet is protected by not less than 1/4" (0,64 cm) ame retardant

millboard covered with not less than No. 28 MSG sheet metal, 0,015" (0,4 mm) stainless

steel, 0,024" (0,6 mm) aluminum, or 0,020" (0,5 mm) copper.

4. 30" (76,2 cm) minimum clearance when the cabinet is unprotected.

5. For cutouts below 22 7/8" (58,1 cm), appliance will slightly show out of the cabinet.

Kenmore Models: Allow at least 19¼" (48,9 cm) clearance for door depth when it is open.

Kenmore ELITE Models: Allow at least 20" (50,8 cm) clearance for door depth when it is open.

Side

Panel

Door Open

(see note 5)

A. HEIGHT

(Under

Cooktop)

WIDTH

C. COOKTOP

WIDTH

D. TOTAL DEPTH

TO FRONT OF

RANGE

E. CUTOUT WIDTH

(Countertop and

cabinet)

F. CUTOUT DEPTH G. HEIGHT

OF COUNTERTOP

35 7/8"

(91,1 cm)

36 5/8"

(93 cm)

30"

(76,2 cm)

Kenmore:

31 5/16" (79,5 cm)

Kenmore ELITE:

31½" (80 cm)

28 5/16"

(71,9 cm)

30±1/16"

(76,2±0,15 cm)

21 3/4" (55,2 cm) Min.

22 1/8" (56,2 cm) Max

24" (61 cm) Min. with

backguard

36 5/8" (93 cm) Max.

35 7/8" (91,1 cm)

Do not

install the unit in the

cabinet before reading

next two pages.

Product Dimensions

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

NOTE: Wiring diagram for these appliances are enclosed in this booklet.

WALL

8" Min.

(20,3 cm Min.)

From Wall Both

Sides

30" Min.

(76,2 cm Min.)

18" Min.

(45,7 cm) Min.

Approx. 1 7/8"

(4,8 cm)

Locate Cabinet Doors

1" (2,5 cm) Min. from

Cutout Opening.

31 1/2"

(80 cm)

Exact

13"

(33 cm)

Shave

Raised Edge

to Clear

Space for a

dimension

C Wide

Cooktop.

1 ½" Max.

(3,8 cm Max.)

30" Min.

(76,2 cm) Min. (see

note 3 on page 3)

24" Min.

(61 cm Min.)

These surfaces should

be at & leveled (hatched

area).

IMPORTANT: Cabinet and

countertop width should match

the cutout width.

Do not install the unit in the

cabinet before reading next 2 pages.

A. HEIGHT

(Under Cooktop)

B. WIDTH

C. COOKTOP

WIDTH

D. TOTAL

DEPTH TO

FRONT OF

RANGE

E. CUTOUT WIDTH

(Countertop and

cabinet)

F. CUTOUT DEPTH

G. HEIGHT

OF COUNTERTOP

35 7/8" (91,1 cm)

36 5/8" (93 cm)

30"

(76,2 cm)

Porcelain cooktop:

31 5/16" (79,5 cm)

Glass Cooktop:

31½" (80 cm)

28 5/16"

(71,9 cm)

30±1/16"

(76,2±0,15 cm)

21 3/4" (55,2 cm) Min.

22 1/8" (56,2 cm) Max

24" (61 cm) Min. with

backguard

36 5/8" (93 cm) Max.

35 7/8" (91,1 cm)

Cabinet Dimensions

1 1/8"

(2,86 cm)

FRONT

CABINET

Ref.

22 7/8" (58,1 cm) min.

23 1/4" (59,05 cm) max.

(see note 4

on page 3)

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

To avoid breakage: Do NOT handle or

manipulate the unit by the cooktop.

1. The counter-top around the cut-out should be at and leveled (see

hatched area on illustration 1).

2. Before installing the unit, measure the heights of the two (2) cabinet

sides (H1-4), front and back (see illustration 1) from the oor to the

top of the counter.

Illustration 1

Shave Raised Edge

to Clear Space

for a Dimension C

(on page 3) Wide

Cooktop.

1 ½" Max.

(3,8 cm Max.)

device: Remove and discard the two rear leveling legs, they are only

in place to solidify the unit during the transport.

Illustration 2

To successfully

install the

range, the initial

level height

from oor to

underside of

cooktop frame

should be at

least 1/16" (0,16

cm) taller than

cabinet sides

as measured in

step 2.

8. After the

installation,

MAKE SURE

that the unit is

supported by the

leveling legs NOT

by the cooktop.

Metal Flange

3. Level the range using the

leveling legs or leveling

device so that the height

from the oor to the

underside of the cooktop

frame is greater than the

tallest cabinet measurement

by at least 1/16" (0,16 cm)

(see illustration 2).

4. Model equipped with leveling

5. Slide the unit into the cabinet. Make sure the center of the unit is aligned with the center

of the cabinet cut-out.

6. Remove the protective channels on each side of cooktop (if equipped).

7. The metal ange under each side of the cooktop MUST be placed

over the cabinet countertop for proper unit support. The cooktop

should NOT directly touch the countertop (see illustration 2) or

else could cause damage to the cooktop voiding the warranty.

Level the unit if needed.

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

Before Starting

Tools you will need

For leveling legs and anti-tip brackets:

● Adjustable wrench or channel lock pliers

●

1/4" (7mm) Nutdriver

●

3/8" (10mm) Nutdriver

● Electric Drill & 1/8 Diameter

Drill Bit (5/32" Masonry Drill

Bit if installing in concrete)

● Level & Measuring Tape

For gas supply connection:

● Pipe Wrench

● Brush

For burner ame adjustment:

● Phillips head and blade-type

screwdrivers

For gas conversion (LP/Propane or Natural):

● Open end wrench - 1/2"

Additional materials you will need:

● Gas line shut-off valve

● Pipe joint sealant that resists action of

LP/Propane gas

● A new exible metal appliance conduit

(½" NPT x ¾" or ½" I.D.) must be design

certied by CSA International. Because

solid pipe restricts moving the range we

recommend using a new exible conduit

(4 feet length) for each new installation and

additional reinstallations.

● Always use the (2) new are union

adapters ½" NPT x ¾" or ½" I.D.) supplied with the

new exible appliance conduit for connection of the

range.

4½

10½

7½

2½

WALL

(76.2)

(5.1)

(30.5)

(12.7)

(19)

(11.4)

(15.2)

(7.6)

(6.4)

(26.7)

2½

(6.4)

(7.6)

(10.1)

(12.7)

Min.

Cutout

Width

Formed or tile countertop

trimmed ¾" (1,9 cm)

back at front corners of

countertop opening.

Figure 1

Cabinet Construction

1.1

To eliminate the risk of cabinet

burns and re, do not have cabinet storage space

above the range. If there is cabinet storage space

above range, reduce risk by installing a range hood

that projects horizontally a minimum of 5" (12,7 cm)

beyond the bottom of the cabinet.

1.2

Countertop Preparation (gure 1)

• The cooktop sides of the range t over the cutout

edge of your countertop.

• If you have a square nish (at) countertop, no

countertop preparation is required. Cooktop sides lay

directly on edge of countertop.

• Formed front-edged countertops must have

molded edge shaved at 3/4" (1,9 cm) from each

front corner of opening (Figure 1).

• Tile countertops may need trim cut back 3/4" (1,9

cm) from each front corner and/or rounded edge

attened (Figure 1).

• If the existing cutout width is greater than

30-1/16" (76,4 cm), reduce the ¾" (1,9 cm)

dimension.

• Countertop must be level. Place a level on the

countertop, rst side to side, then front to back. If

the countertop is not level, the range will not be

level. The oven must be level for satisfactory baking

results. Cooktop sides of range t over edges of

countertop opening.

1.3

Gas and Electric Entry Preparation

• The hatched areas are the locations where the gas

line can enter the cabinet (gure 2).

• The recommended position for the gas entry line is

located at 7¼" (18,4 cm) from the left cabinet wall

and 2" (5,1 cm) from the oor (gure 2).

• The shaded area is the location where the electric

outlet can be located (gure 2).

Recommended

position

Note: All dimensions are in inches (centimeter).

Figure 2

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

Provide an adequate Gas Supply

When shipped from the factory, this unit is designed

to operate on 4" (10,16 cm) water column (1,0 kPa)

Natural gas manifold pressure. A convertible pressure

regulator is connected to the range manifold and

MUST be connected in series with the gas supply line.

If LP/Propane conversion kit has been used, follow

instructions provided with the kit for converting the

pressure regulator to LP/Propane use.

Care must be taken during installation of range not to

obstruct the ow of combustion and ventilation air.

For proper operation, the maximum inlet pressure

to the regulator should be no more than 14" (35,56

cm) of water column pressure (3,5 kPa). The inlet

pressure to the regulator must be at least 1" (0,25 kPa)

greater than the regulator manifold pressure setting.

Examples: If regulator is set for natural gas 4" (10,16

cm) manifold pressure, inlet pressure must be at least

5" (12,7 cm); if regulator has been converted for LP/

Propane gas 10" (25,4 cm) manifold pressure, inlet

pressure must be at least 11" (27,9 cm).

Leak testing of the appliance shall be conducted

according to the instructions in step 4.

The gas supply line should be ½" or ¾" I.D. (Interior

Diameter)

Seal the openings

Seal any openings in the wall behind the range and

in the oor under the range after gas supply line is

installed.

Connect the range to the gas

supply

Important: Remove all packing material and literature

from range before connecting gas and electrical

supply.

To prevent leaks, put pipe joint sealant on all external

pipe threads.

Your regulator is in location as shown in gure 3.

Do not allow regulator to rotate on

pipe when tightening ttings.

Connection to Pressure Regulator

The regulator is already installed on the appliance.

Do not make the connection too tight.

The regulator is die cast. Overtightening may crack the

regulator resulting in a gas leak and possible re or

explosion.

Assemble the exible connector from the gas supply

pipe to the pressure regulator in the following order:

1. manual shutoff valve (not included)

2. 1/2" nipple (not included)

3. 1/2" are union adapter (not included)

4. exible connector (not included)

5. 1/2" are union adapter (not included)

6. 1/2" nipple (not included)

7. pressure regulator (included)

Use pipe-joint compound made for use with Natural

and LP/Propane gas to seal all gas connections. If

exible connectors are used, be certain connectors are

not kinked.

The supply line must be equipped with an approved

manual shutoff valve. This valve should be located

in the same room as the range and should be in a

Shutoff Valve -

Open position

to appliance

to gas supply line

All connections must be wrench-tightened

Flare

Union

Flare

Union

GAS FLOW

Manual

Shutoff

Valve

Pressure

Regulator

Off

Flexible

Connector

Access

Cap

Nipple Nipple

Figure 4

• If you are using a through the oor gas entry, remove

the line protector shield from the bottom of the unit to

allow access for the pipe line (gure 3).

• We recommend to install a pipe elbow right out of the

oor or wall towards the center of the unit to ease the

installation.

To remove the line protector, remove the 3 screws.

Figure 3

Gas pressure regulator location

location that

allows ease of

opening and

closing. Do not

block access to

the shutoff valve.

The valve is for

turning on or

shutting off gas

to the appliance.

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

Once regulator is in place, open the shutoff valve in the

gas supply line. Wait a few minutes for gas to move

through the gas line.

Check for leaks. After connecting the range to the gas

supply, check the system for leaks with a manometer.

If a manometer is not available, turn on the gas supply

and use a liquid leak detector (or soap and water) at all

joints and connections to check for leaks.

Do not use a ame to check for leaks

from gas connections. Checking for leaks with a ame

may result in a re or explosion.

Tighten all connections as necessary to prevent gas

leakage in the range or supply line.

Disconnect this range and its individual manual

shutoff valve from the gas supply piping system

during any pressure testing of that system at test

pressures greater than 1/2 psig (3,5 kPa or 14" water

column).

Isolate the range from the gas supply piping

system by closing its individual manual shutoff valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psig

(3,5 kPa or 14" water column).

LP/Propane Gas Conversion

This appliance can be used with Natural gas or LP/

Propane gas. It is shipped from the factory for use with

natural gas.

If you wish to convert your range for use with LP/

Propane gas, use the supplied xed orices located

in a bag containing the literature marked "FOR

LP/PROPANE GAS CONVERSION". Follow the

instructions packaged with the orices for surface,

oven and broil burners conversion.

The conversion must be performed by a qualied

service technician in accordance with the

manufacturer's instructions and all local codes and

requirements. Failure to follow these instructions

could result in serious injury or property damage.

The qualied agency performing this work assumes

responsibility for the conversion.

Failure to make the appropriate

conversion can result in serious personal injury and

property damage.

Electrical Requirements

120 volt, 60 Hertz, properly grounded dedicated circuit

protected by a 15 amp circuit breaker or time delay

fuse.

Do not use an extension cord with this range.

Preferred Method

Grounding type

wall receptacle

Do not, under any

circumstances,

cut, remove,

or bypass the

grounding prong.

Power supply cord with

3-prong grounding plug.

Figure 5

Grounding Instructions

IMPORTANT Please read carefully.

For personal safety, this appliance must be

properly grounded.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong grounding wall receptacle (see Figure 5) to

minimize the possibility of electric shock hazard from

the appliance.

The wall receptacle and circuit should be checked by

a qualied electrician to make sure the receptacle is

properly grounded.

Where a standard 2-prong wall receptacle is installed,

it is the personal responsibility and obligation of the

consumer to have it replaced by a properly grounded

3-prong wall receptacle.

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

Disconnect electrical supply cord from

wall receptacle before servicing the appliance.

Moving the Appliance for

Servicing and Cleaning

Turn off the range line fuse or circuit breakers at

the main power source, and turn off the manual gas

shut-off valve. Make sure the range is cold. Remove

the service drawer (warmer drawer on some models)

and open the oven door. Lift the range at the front

and slide it out of the cut-out opening without creating

undue strain on the exible gas conduit. Make sure

not to pinch the exible gas conduit at the back of the

range when replacing the unit into the cut-out opening.

Replace the drawer, close the door and switch on the

electrical power and gas to the range.

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

BACK EDGE OF

RANGE LINE OR

REAR WALL

ANTI-TIP

BRACKET

10

(25.4 cm)

Toe

Plate

Door

Cabinet

Kitchen

Cabinet

SLIDE

BACK

(

L = Center line)

Range

Anti-Tip Bracket

Floor Mount

Screws

Floor

Rear of Range

Wall

1. Draw a center line (CL) on the oor where the range

should be installed. Also draw a line on the oor at

the range back position if there is no wall.

2. Unfold paper template and place it at on the oor

with the right rear corner positioned exactly on the

intersection of the center and back lines you just

drew before. (Use the diagram below to locate

brackets if template is not available (Figure 6)).

3. Mark on the oor the location of the 4 mounting holes

shown on the template. For easier installation, 3/16"

(0,48 cm) diameter pilot holes 1/2" (1,27 cm) deep

can be drilled into the oor.

4. Remove template and place bracket on oor. Line up

holes in bracket with marks on oor and attach with

4 screws provided. Bracket must be secured to solid

oor (Figure 7). If attaching to concrete oor, rst drill

3/16" (0,48 cm) dia. pilot holes using masonry drill bit.

5. Be sure the 4 leveling legs are at the highest position

they can be.

6. Slide range into place making sure structure of the

range is trapped by the anti-tip bracket (Figure 7).

Lower the range by adjusting the 4 leveling legs until

the underside of the cooktop is sitting level on the

countertop. Refer to "Leveling the Range" section.

7. After installation, verify that the anti-tip bracket is

engaged by grasping the top rear edge of the range

and carefully attempt to tilt it forward to make sure

range is properly anchored.

Anti-Tip Brackets Installation

Instructions

8.1

Models Equipped with Leveling Device

To reduce the risk of tipping of the range,

the range must be secured to the oor by properly installed

anti-tip bracket and screws packed with the range. These

parts are located in the oven. Failure to install the anti-tip

bracket will allow the range to tip over if excessive weight

is placed on an open door or if a child climbs upon it.

Serious injury might result from spilled hot liquids or from

the range itself.

Follow the instructions below to install the anti-tip

brackets.

If range is ever moved to a different location, the anti-

tip brackets must also be moved and installed with the

range.

Tools Required:

Adjustable Wrench

Ratchet

Drill & 1/8" (0,32 cm) bit

5/16" (0,8 cm) Nutdriver

Level

The anti-tip bracket attaches to the oor at the back of

the range to prevent range from tipping. When fastening

bracket to the oor, be sure that screws do not penetrate

electrical wiring or plumbing. The screws provided will

work in either wood or concrete.

Figure 6

Figure 7

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

B. Drill Pilot Holes and Fasten Bracket - Drill a 1/8"

(0,3 cm) pilot hole where screws are to be located. If

bracket is to be mounted to the wall, drill pilot hole at

an approximate 20° downward angle. If bracket is to be

mounted to masonry or ceramic oors, drill a 3/16" (0,5

cm) pilot hole 1-3/4" (4,4 cm) deep. The screws provided

may be used in wood or concrete material. Use a 5/16"

(0,8 cm) nut-driver or at head screwdriver to secure the

bracket in place.

C. Level and position the range - Slide range to its

nal position. Insert the range leveling leg in the anti-tip

bracket. Visually verify if the anti-tip bracket is engaged.

Lower the range by adjusting the 4 leveling legs

alternatively until the range is level. Check if the range

is level by placing a spirit level on the oven rack. Take

2 readings with the spirit level placed diagonally; take a

reading in one direction and then in the other direction.

Level the range if necessary by adjusting the leveling

legs.

Leg

Leveler

Raise

Lower

FASTEN BRACKET

ALL OR FLOOR MOUNTING)

Leveling leg

Wall mount

Floor Mount

Anti-Tip Bracket

Rear of Range

Wall Plate

8.2

Models Equipped with Leveling Legs

To reduce the risk of tipping of the

range, the range must be secured to the oor by the

properly installed anti-tip bracket and screws packed

with the range. Failure to install the anti-tip bracket will

allow the range to tip over if excessive weight is placed

on an open door or if child climbs upon it. Serious injury

might result from spilled hot liquids or from the range

itself.

If range is ever moved to a different location, the anti-

tip bracket must also be moved and installed with the

range.

Instructions are provided for installation in wood or

cement oor. When fastening to oor, be sure that

screws do not penetrate electrical wiring, gas or

plumbing.

A. Locate the Bracket Using the Template

Figure 11

Figure 12

Figure 9

Figure 8

Locate the bracket position (right

or left side) by placing the template

symmetrically to the center of

the nal range position. Mark the

location of the screw holes, shown

on template.

Range side

Figure 10

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

Range Installation

Important Note: Door removal is not a requirement for

installation of the range, but is an added convenience.

Refer to the Use

and Care Guide for

oven door removal

instructions.

Standard Installation

9.1

The range cooktop overlaps the countertop at

the sides and the range rests on the oor. The

cooktop is 31 1/2" (80 cm) wide.

9.2

Install base cabinets 30" (76,2 cm) apart. Make

sure they are plumb and level before attaching

cooktop. Shave raised countertop edge to clear

31 1/2" (80 cm) wide range top rim.

9.3

Install cabinet doors 31" (78,7 cm) min. apart so it

will not interfere with range door opening.

9.4

Cutout countertop exactly as shown on page 4.

For models equipped with Leveling Device:

9.5

Make sure the front leveling legs and the rear

leveling device are setup higher than the height

of the cabinet.

9.6

Install the anti-tip bracket at

this point before placing the range at its nal

position. Follow the installation instructions on

page 9 or 10 or on the anti-tip bracket template

supplied with the range.

9.7

To provide an optimum installation, the top

surface of the countertop must be level and

at (lie on the same plane) around the 3 sides

that are adjacent to range cooktop. Proper

adjustments to make the top at should be made

or gaps between the countertop and the range

cooktop may occur.

9.8

To reduce the risk of damaging

your appliance, do not handle or manipulate it by

the cooktop or control console. Manipulate with

care.

9.9

Position range in front of the cabinet opening.

9.10

Make sure that the cooktop which overhangs the

countertop clears the countertop. If necessary,

raise the unit by lowering the leveling legs.

9.11

Slide the range into the cutout opening and

center it before leveling it.

9.12

Level the range (see section 10). The oor

where the range is to be installed must be level.

Follow the instructions under "Leveling the

Range- Models Equipped with Leveling Device".

9.13

Adjust leveling legs so that the underside of the

cooktop is sitting on the countertop. Carefully

screw in (refer to Leveling the range: "Models

equipped with Leveling Device") the back leveling

leg until the cooktop overhang touches slightly

the countertop. Then carefully screw in the front

two leveling legs until the cooktop overhang

touches slightly the countertop.

For models equipped with Leveling Leg

only (no leveling device):

9.5

Make sure the four leveling legs (front and rear)

are setup higher than the height of the cabinet

(shown on page 3).

9.6

Install the anti-tip bracket at

this point before placing the range at its nal

position. Follow the installation instructions on

page 9 or 10 or on the anti-tip bracket template

supplied with the range.

9.7

To provide an optimum installation, the top

surface of the countertop must be level and

at (lie on the same plane) around the 3 sides

that are adjacent to range cooktop. Proper

adjustments to make the top at should be made

or gaps between the countertop and the range

cooktop may occur.

9.8

To reduce the risk of damaging

your appliance, do not handle or manipulate it by

the cooktop. Manipulate with care.

9.9

Position range in front of the cabinet opening.

9.10

Make sure that the cooktop which overhangs the

countertop clears the countertop. If necessary,

raise the unit by lowering the leveling legs.

9.11

Level the range (see section 10). The oor

where the range is to be installed must be level.

Follow the instructions under "Leveling the

Range-Models Equipped with Leveling Legs".

9.12

Slide the range into the cutout opening.

Figure 13

IMPORTANT

If Accessories Needed

Installation With Backguard

A backguard kit can be ordered through a Sears

Service Center. The cutout depth (21¾" (55,2 cm)

Min., 22

" (56,2 cm) Max.) needs to be increased to

24" (61 cm) when installing a backguard

Installation With End Panel

An end panel kit can be ordered through a Sears

Service Center.

Installation With Side Panel

A side panels kit can be ordered through a Sears

Service Center. Install cabinet doors 31" (78,7 cm) min.

apart so as not to interfere with range door opening.

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

Figure 14

10.

Leveling the Range

10.1

Models Equipped with Leveling Device

Level the range after installation in the cutout opening.

1. Open the range drawer. The leveling screws control

the height of the rear leg.

2. Adjust the appliance legs as follows until the

underside of the cooktop (or cooktop glass) surface

is sitting level on the countertop (Figure 14).

a. To adjust the front legs, use a wrench on the

leg base and turn counterclockwise to lower or

clockwise to raise the range.

b. To adjust the rear legs, use a ratchet or a nutdriver

and turn the leveling screws counterclockwise to

lower or clockwise to raise the range.

3. Check if the range is level by installing an oven rack

in the center of the oven and placing a level on the

rack (Figure 15).

4. Take 2 readings with the level placed diagonally in

one direction and then the other. Level the range, if

necessary, by adjusting the leveling legs.

5. If the range cannot be level, contact a carpenter to

correct sagging or sloping oor.

10.2

Models Equipped with Leveling Legs

Level the range and set cooktop height before

installation in the cut-out opening.

1. Install an oven rack in the center of the oven.

2. Place a level on the rack (see Figure 15). Take 2

readings with the level placed diagonally in one

direction and then the other. Level the range, if

necessary, by adjusting the 4 leg levelers with a

wrench (see Figure 11).

3. Taking care to not damage the countertop, slide

range into cutout opening and double check for

levelness.

11.

Decorative Rear Trim Installation

(some models)

1. Disconnect the power from the range.

2. Make sure the range is leveled.

3. Pull range toward you.

4. Measure the distance between the oor and the

surface underneath the cooktop frame.

5. Mark that distance on the wall where the decorative

trim will be installed.

6. Draw a line.

7. Place the top of the decorative trim under that line.

8. Using the screws provided x the decorative trim

into the wall.

9. Slide the range back into position as far as it will go

and reconnect the power source.

Decorative Trim

Screw (3)

Distance

between

the oor

and the

surface

underneath

the cooktop

frame.

12.

Check Operation

Refer to the Use and Care Guide packaged with the

range for operating instructions and for care and

cleaning of your range.

Remove all packaging from the oven before testing.

12.1

Check Burner Cap Placement

It is very important to be sure that all surface burner

caps and burner grates are properly installed and in

the correct locations before operating the appliance.

Please note that the burner heads are secured to

the cooktop. The cooktop is not removable. Do not

attempt to remove or lift the cooktop.

Figure 15

Figure 16

Note: If your appliance

does not include a rear

trim and you would like

to purchase one, please

contact your dealer or

servicer.

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

Hollow

Valve

Stem

Figure 21

Figure 22

12.2

Turn on Electrical Power and Open

Main Shutoff Gas Valve

Fig. 20

Burner Cap

Burner

Head

Fig. 17

Correct Burner Cap

Placement - Fig. 18

Incorrect Burner Cap

Placement - Fig. 19

Burner

Cap Lip

12.3

Check the Igniters

Operation of electric igniters should be checked after

range and supply line connectors have been carefully

checked for leaks and range has been connected to

electric power.

a. To check for proper lighting, push in and turn a surface

burner knob to the LITE position. You will hear the

igniter sparking.

b. The surface burner should ignite when gas is available

to the burner. Purge air from supply lines by leaving

knob in the LITE position until burner ignites. Each

burner should light within four (4) seconds in normal

operation after air has been purged from supply lines.

c. Visually check that burner has a ame, Once the

burner ignites, the control knob should be turned

out of the LITE position.

d. Try each surface control knob separately until all

burner valves have been checked. Each burner

location is equipped with a separate electrode.

12.4

Adjust the "LOW" Setting of Surface

Burner Valves (linear ow)

Test to verify if LOW setting should be adjusted:

a. Push in and turn control to LITE until burner ignites.

b. Push in and quickly turn knob to lowest position.

c. If burner goes out, reset control to OFF.

d. Remove the surface burner control knob.

For all burner styles (except Bridge burner)

e. Insert a thin-bladed screwdriver into the hollow valve

stem and engage the slotted screw inside. Flame

size can be increased or decreased with the turn of

screw. Turn counterclockwise to increase ame size.

Turn clockwise to decrease ame size (Figure 21).

Adjust ame until you can quickly turn knob from LITE

to lowest position without extinguishing the ame. Flame

should be as small as possible without extinguishing.

NOTE: On dual burners, the inner ame cannot be

adjusted. Adjustments are made to the outer ame only.

For Bridge burner style adjustment only:

e. The ame size on the rear portion of the bridge

burner can be increased or decreased by turning

screw A. Use screw B to adjust ame size of the

center portion of the Bridge Burner (Figure 22). Turn

the screw counterclockwise to increase ame size.

Turn clockwise to decrease ame size. Adjust ame

size until you can quickly turn the knob from LITE to

lowest position without extinguishing the ame.

Note: Air mixture adjustments are not required on

surface burners.

To prevent are-ups and avoid

creation of harmful by-products, do not use the cooktop

without all burner caps properly installed to insure

proper ignition and gas ame size.

Always keep the burner caps and burner heads in

place whenever the surface burners are in use. DO

not allow spills, food, cleaning agents or any other

material to enter the gas orice holder openings.

Check and be sure the size of each burner cap

matches the size of the burner head. Check and be

sure that all round style burner caps are correctly in

place on round burner heads.

Check and be sure that all oval style burner caps are

correctly in place on oval burner heads (if equipped).

Check and be sure that all dual or twin style burner

caps are correctly in place on dual or twin heads (if

equipped).

On round style burners, the burner cap lip (Figure 17)

should t snug into the center of burner head and be

level. Refer to gures 18 & 19 for correct and incorrect

burner cap placement.

Once in place, you may check the t by gently sliding

the burner cap from side to side (Figure 20) to be sure

it is centered and rmly seated. When the burner cap lip

makes contact inside the center of the burner head you

will be able to hear the burner cap click. Please note

that the burner cap should NOT move off the center of

the burner head when sliding from side to side.

30" GAS SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with Sealed Top Burners)

Air Shutter

Waist-High Burner

Lower Oven Bottom

(removable)

Lower

Oven Bafe

(removable)

Figure 23

12.5

Operation of Oven Burners and Oven

Adjustments

12.5.1 Electric Ignition Burners

Operation of electric igniters should be checked after

range and supply line connectors have been carefully

checked for leaks, and range has been connected to

electric power.

The oven burner is equipped with an electric control

system as well as an electric oven burner igniter. If your

model is equipped with a waist-high broil burner igniter,

it will also have an electric burner igniter. These control

systems require no adjustment. When the oven is set to

operate, current will ow to the igniter. It will "glow" similar

to a light bulb. When the igniter has reached a temperature

sufcient to ignite gas, the electrically controlled oven valve

will open and ame will appear at the oven burner. There

is a time lapse from 30 to 60 seconds after thermostat is

turned ON before the ame appears at the oven burner.

When the oven reaches the display setting, the glowing

igniter will go off. The burner ame will go "out" in 20 to 30

seconds after igniter goes "OFF". To maintain any given

oven temperature, this cycle will continue as long as the

display is set to operate.

After removing all packing materials and literature from

the oven:

a) Set the oven to BAKE at 300°F. See Use & Care

Guide for operating instructions.

b) Within 60 seconds the oven burner should ignite.

Check for proper ame, and allow the burner to cycle

once. Reset controls to off.

c) If your model is equipped with a high-waist broiler,

set oven to broil. See Use & Care Guide for operating

instructions.

d) Within 60 seconds the broil burner should ignite.

Check for proper ame. Reset controls to off.

12.5.2 Air Shutter-Oven Burner

The approximate oven burner ame length is 1 inch

(distinct inner cone of blue ame).

To determine if the oven burner ame is proper, remove

the oven bottom and burner bafe and set the oven to

bake at 300°F.

To remove the oven bottom, remove oven hold down

screws at rear of oven bottom. Pull up at rear, disengage

front of oven bottom from oven front frame, and pull the

12.5.3 Air Shutter-Broil Burner

The approximate ame length of the burner is 1 inch

(distinct inner cone of blue ame). To determine if the

broil burner ame is proper, set the oven to broil. If ame

is yellow, increase air shutter opening size (see "2" in

Figure 24). If the entire ame is blue, reduce the air

shutter opening size. To adjust, loosen lock screw (see

"3" in Figure 24), reposition air shutter, and tighten lock

screw.

When All Hookups are Complete

Make sure all controls are left in the OFF position.

Make sure the ow of combustion and ventilation air to

the range is unobstructed.

Model and Serial Number Location

The serial plate is located on the oven front frame

behind the oven door (some models) or on the drawer

side frame (some models).

When ordering parts for or making inquiries about your

range, always be sure to include the model and serial

numbers and a lot number or letter from the serial plate

on your range.

Your serial plate also tells you the rating of the burners,

the type of fuel and the pressure the range was

adjusted for when it left the factory.

Before You Call for Service

Read the Before You Call Checklist and operating

instructions in your Use and Care Guide. It may save

you time and expense. The list includes common

occurrences that are not the result of defective

workmanship or materials in this appliance.

Refer to your Use & Care Guide for Sears service

phone numbers or call 1-800-4-MY-HOME®.

oven bottom out of the oven. Remove burner bafe so

that burner ame can be observed.

If the ame is yellow, increase air shutter opening size

(see "2" in Figure 24). If the entire ame is blue, reduce

the air shutter opening size.

To adjust frame loosen lock screw (see "3" in Figure 24),

reposition air shutter, and tighten lock screw. Replace

oven bottom.

Oven Burner Tube

Orice Hood

Lock Screw

Air Shutter

Figure 24

Impreso en los Estados Unidos

Si la información contenida en este manual no es seguida

exactamente, puede ocurrir un incendio o explosión causando daños materiales,

lesión personal o la muerte.

PARA SU SEGURIDAD:

— Noalmaceneniutilicegasolinauotrosvaporesylíquidosinamablesenla

proximidad de éste o de cualquier otro artefacto.

— QUE DEBE HACER SI PERCIBE OLOR A GAS:

• No trate de encender ningún artefacto.

• Notoqueningúninterruptoreléctrico;nouseningúnteléfonoensuedicio.

• Llame a su proveedor de gas desde el teléfono de un vecino. Siga las instrucciones

del proveedor de gas.

• Si no logra comunicarse con su proveedor de gas, llame al departamento de

bomberos.

— Lainstalaciónyelserviciodemantenimientodebenserefectuadosporun

instaladorcalicado,laagenciadeserviciooelproveedordegas.

LA INSTALACIÓN Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR

CALIFICADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR

LOCAL DE ELECTRICIDAD. LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA

FUTURA.

INSTRUCCIONES DE INSTALACIÓN DE

COCINAS DE GAS DE 30"

Notas importantes para el instalador

1. Lea todas las instrucciones antes de instalar la cocina.

2. Saque todo el material usado en el embalaje del

compartimiento del horno antes de conectar el

suministro eléctrico o de gas a la estufa.

3. Observe todo código o reglamento.

4. Asegúrese de dejar estas instrucciones con el

consumidor

5. Nota: Para la utilización a más de 2 000 pies de

altura, la potencia del aparato deberá ser reducida de

4 por ciento a cada 1 000 pies adicionales.

Nota importante para el consumidor

Mantenga estas instrucciones con el manual del usuario

para futuras referencias.

Tabladematerias

Importantes instrucciones de seguridad ....................... 16

Dimensiones de la unidad & de la gabinete ............ 17-18

Para evitar fractura de la unidad .................................. 19

Antes de comenzar....................................................... 20

Construcción del armario.........................................20-21

Proporcione un suministro de gas adecuado ............... 21

Selle las aperturas ........................................................ 21

Conecte la estufa al suministro de gas......................... 21

Conversión para uso de propano liquido ...................... 22

Requisitos eléctricos..................................................... 22

La mudanza del aparato para reparaciones o limpieza ....22

Instrucciones para la instalación de las

jaciones de anti-inclinacion ...................................23-24

Instalación de la estufa .......................................................25

Nivelación de la estufa .......................................................26

Instalación de accesorio decorativo trasero ......................26

Comprobación del Funcionamiento .........................27-28

Después de terminar la instalación .............................. 28

Ubicación del numero de modelo y de serie ................ 28

Antes de llamar al servicio............................................ 28

Aparatos Instalados en el estado de

Massachusetts;

Este Aparato sólo puede ser instalado en el estado

de Massachusetts por un plomero o ajustador de gas

licenciado de Massachusett.

Este aparato se debe instalar con un largo conector

exible de gas de tres (3) pies/36 pulgadas.

Una válvula manual de gas de tipo manija de forma de "T"

se debe instalar en la línea del suministro de gas de este

aparato.

Los controles eléctricos pueden

ser dañados con frías temperaturas. Cuando utilice su

estufa por la primera vez, o si no ha sido utilizada por

mucho tiempo asegúrese que no haya sido expuestas a

temperaturas más altas que 0°C/32°F por más de 3 horas

antes de conectar su estufa al suministro eléctrico.

Estados unidos

Canada

Consulte la placa de

serie para vericar la

certicación vigente

del organismo

correspondiente

P/N 809018301 (1507) Rev. A

English – pages 1-14; Spanish - pages 15-28; Français – pages 29-43

INSTRUCCIONES DE INSTALACIÓN DE COCINAS DE GAS DE 30"

(Modelos con quemadores sellados)

Instalación de esta estufa debe cumplir con todos los

códigos locales, o en ausencia de códigos locales con

el Código Nacional de Gas Combustible ANSI Z223.1/

NFPA .54—última edición.

El diseño de esta estufa ha sido certicado por la

CSA Internacional. En éste como en cualquier otro

artefacto que use gas y genere calor, hay ciertas

precauciones de seguridad que usted debe seguir.

Estas serán encontradas en el Manual del Usuario,

léalo cuidadosamente.

•Nosedebenusarcortinasdeairenininguna

otra campana de ventilación superior que sople

airehaciaabajosobrelaestufaagasamenos

que la campana de ventilación y la estufa hayan

sidodiseñadas,probadasycerticadasporun

laboratoriodepruebasindependienteparaeluso

combinadodelaunaconlaotra.

• Asegúrese de que la estufa sea instalada y

conectada a tierra en forma apropiada por un

instaladorcalicadooporuntécnico.

• Estaestufadebesereléctricamentepuestaa

tierra de acuerdo con los códigos locales, o en su

ausencia, con el Código Eléctrico Nacional ANSI/

NFPA No. 70, última edición. Vea las instrucciones

para la puesta a tierra.

• Antes de instalar la estufa en un área cuyo

pisoesterecubiertoconlinóleouotrotipode

piso sintético, asegúrese de que éstos puedan

resistir una temperatura de por lo menos 90°F

sobrelatemperaturaambientalsinprovocar

encogimiento, deformación o decoloración. No

instale la estufa sobre una alfombra al menos que

coloque una plancha de material aislante de por lo

menos 1/4 pulgada, entre la estufa y la alfombra.

• Asegúresedequeelmaterialquerecubrelas

paredes alrededor de la estufa, pueda resistir el

calor generado por la estufa.

• Noobstruyaelujodelairedecombustiónenla

ventilación del horno ni tampoco alrededor de la

baseodebajodelpanelinferiordelanterodela

estufa. Evite tocar las aberturas o áreas cercanas

de la ventilación, ya que pueden estar muy calientes

durante el funcionamiento del horno. La estufa

requiere aire fresco para la combustión apropiada de

los quemadores.

Nuncadejeniñossoloso

desatendidos en un área donde un artefacto

está siendo usado. A medida que los niños crecen,

enséñeles el uso apropiado y de seguridad para todos

los artefactos. Nunca deje la puerta del horno abierta

cuando la estufa está desatendida.

No se pare, apoye o siente en

laspuertasocajonesdeestaestufapuespuede

resultarenseriaslesionesypuedetambiéncausar

daño a la estufa.

• No almacene artículos que puedan interesar a los

niñosenlosgabinetessobrelaestufa.Los niños

pueden quemarse seriamente tratando de trepar a la

estufa para alcanzar estos artículos.

• Losgabinetesdealmacenamientosobrelaestufa

debenserevitados,paraeliminarlanecesidad

detenerquepasarsobrelosquemadores

superiores de la estufa para llegar a ellos.

• Ajusteeltamañodelallamadelosquemadores

superioresdetalmaneraqueéstanosobrepase

elbordedelosutensiliosdecocinar. La llama

excesiva es peligrosa.

• Nouseelhornocomoespaciodealmacenaje.

Esto creará una situación potencialmente peligrosa.

IMPORTANTES INSTRUCCIONES DE SEGURIDAD

Estemanualcontieneimportantesmensajesdeseguridad.Siempreleayobedezcatodomensaje

de seguridad.

Indica una situación muy peligrosa, la cual de no ser evitada puede ocasionar graves

heridas y hasta la muerte.

ATENCION

Indica una situación de peligro inminente, la cual de no ser evitada puede

ocasionar heridas leves o daños al producto solamente.

• Un niño o adulto puede volcar la estufa

y acabar muerto.

• Vericar que el braquet trasero

este calibrado con la cubierta o el

utensilio del anti-vuelco sea instalado

Riesgo de volcamiento

en las paredes del cabinete como la indican las

instrucciones.

• Asegurar que el braquet antivuelco sea calibrado con la

cubierta o los lados de la cabina así como lo indican las

instrucciones cuando la estufa sea movida.

• No utilice la estufa sin el dispositivo antivuelco instalado

y acoplado.

• Si no se siguen estas instrucciones, se puede provocar la

muerte o quemaduras graves en niños y adultos.

Para vericar si la jaciones de anti-inclinación

está instalado correctamente, sostenga el

borde trasero de la parte trasera de la estufa

usando ambos brazos. Intente inclinar la

estufa hacia adelante con cuidado. Si está

instalada correctamente, la estufa no debería inclinarse

hacia adelante.

Consulte las instrucciones de instalación del soporte

antivuelco proporcionadas con la estufa para instalarlo

adecuadamente.

INSTRUCCIONES DE INSTALACIÓN DE COCINAS DE GAS DE 30"

(Modelos con quemadores sellados)

21¾

(55.25 cm)

• Nunca use la estufa para calentar el cuarto.

El uso prolongado de la estufa sin la adecuada

ventilación puede resultar peligroso.

• No almacene ni utilice gasolina u otros vapores

ylíquidosinamablesenlaproximidaddeéste

o de cualquier otro artefacto eléctrico. Puede

provocar incendio o explosión.

• En caso de una interrupción del servicio eléctrico, es

posible de encender los quemadores de supercie

a mano. Para encender un quemador de supercie,

acerque un fósforo encendido del cabezal del

quemador, y gire delicadamente el botón de control

de supercie a LITE (encendido). Tener cuidado al

encender los quemadores a mano.

• Ajustetodosloscontrolesalaposición

"OFF"(apagada)despuésdehaberhechouna

operación con tiempo programado.

PARA MODELOS AUTOLIMPIANTES:

• Saque la asadera, alimentos o cualquier otro

utensilioantesdeusarelciclodeautolimpieza

del horno. Limpie todo exceso de derrame de

alimentos. Siga las instrucciones de prelimpiado en

el Manual del Usuario.

• A diferencia de la gama estándar cocinas de gas,

ESTA PLANCHA DE COCINA NO ES MOVIBLE. No

intente quitar la plancha de cocina.

NOTAS:

1. No pellizque el cordón eléctrico o el conducto

exible de gas entre la estufa y la pared.

Puerta

abierta

(vea la

nota 5)

Panel lateral

A. ALTURA

(Bajo Cubierta)

ANCHO

C. ANCHO DE

LA PLANCHA DE

COCINAR

PROFUNDIDAD

A LA FRENTE DE

LA ESTUFA

E. ANCHO DE

RECORTADO

(cubierta y

armario)

F. PROFUNDIDAD

DE RECORTADO

G. ALTURA DEL

MOSTRADOR

35 7/8" (91,1 cm)

36 5/8" (93 cm)

30"

(76,2 cm)

Kenmore:

31 5/16" (79,5 cm)

Kenmore ELITE:

31½" (80 cm)

28 5/16"

(71,9 cm)

30 ± 1/16"

(76,2 ± 0,15 cm)

21 3/4" (55,2 cm) Min.

22 1/8" (56,2 cm) Max

24" (61cm) Min. con

protector trasero

36 5/8" (93 cm) Max.

35 7/8" (91,1 cm)

No instale la unidad en el

gabinetesinohaleídoestapágina.

Dimensiones de la unidad

5. Para los recortados menos que 22 7/8" (58,1 cm), el electrodoméstico aparecería

ligeramente en el exterior del armario.

Kenmore Models: Deje por los 19 ¼" (48,9 cm) de espacio libre para la profundidad de la

puerta cuando este abierta.

Kenmore ELITE Models: Deje por los 20" (50,8 cm) de espacio libre para la profundidad

de la puerta cuando este abierta.

2. No selle la estufa a los armarios de lado.

3. Un espacio mínimo de 24" (61 cm) entre

la supercie de la estufa y el fondo del

armario esto cuando el fondo del armario

de madera o metal está protegido por

no menos de 1/4" (0,64 cm) de madera

resistente al fuego cubierta por una

lámina metálica de MSG, número 28,

0,015" (0,4 mm) de acero inoxidable,

0,024" (0,6 mm) aluminio, o 0,020" (0,5

mm) de cobre.

4. Un espacio mínimo de 30" (76,2 cm)

cuando el armario no este protegido.

INSTRUCCIONES DE INSTALACIÓN DE COCINAS DE GAS DE 30"

(Modelos con quemadores sellados)

1 1/8"

(2,86 cm)

FRONT

CABINET

Ref.

22 7/8" (58,1 cm) min.

23 1/4" (59,05 cm) max.

(vea pagina 17,

nota 4)

NOTA:Seadjuntaeldiagramadecablesdeestacocinaalnaldeestelibreta.

Localice las puertas del

armario 1" (2,5 cm) mín

del hueco de la abertura.

Acepille el

borde subido

a que deje

espacio para

un borde de

dimensión C

de anchura

de estufa.

IMPORTANTE: El ancho de la

cubiertayelarmariodebedeser

igual al ancho del corte.

Noinstalelaunidadenelgabi-

nete si no ha lado esta 2 página.

A. ALTURA

(Bajo Cubierta)

ANCHO

C. ANCHO DE

LA PLANCHA DE

COCINAR

PROFUNDIDAD

A LA FRENTE

DE LA ESTUFA

E. ANCHO DE

RECORTADO

(cubierta y

armario)

F. PROFUNDIDAD

RECORTADO

G. ALTURA DEL

MOSTRADOR

35 7/8" (91,1 cm)

36 5/8" (93 cm)

30"

(76,2 cm)

Kenmore:

31 5/16" (79,5 cm)

Kenmore ELITE:

31½" (80 cm)

28 5/16"

(71,9 cm)

30 ± 1/16"

(76,2 ± 0,15 cm)

21 3/4" (55,2 cm) Min.

22 1/8" (56,2 cm) Max

24" (61 cm) Min. con

protector trasero

36 5/8" (93 cm) Max.

35 7/8" (91,1 cm)

PARED

8" Min.

(20,3 cm Min.)

From Wall Both Sides

30" Min.

(76,2 cm Min.)

18" Min.

(45,7 cm) Min.

Approx. 1 7/8"

(4,8 cm)

31 1/2"

(80 cm)

Exacto

13"

(33 cm)

1 ½" Max.

(3,8 cm Max.)

30" Min.

(76,2 cm) Min.

(vea pagina

17, nota 3)

24" Min.

(61 cm Min.)

Lasuperciedebe

estar plana y nivelada

(areasombreada).

DimensionesdelaGabinete

INSTRUCCIONES DE INSTALACIÓN DE COCINAS DE GAS DE 30"

(Modelos con quemadores sellados)

Para evitar fractura de la unidad: NO manipule la unidad

sosteniendolacubierta.

1. La cubierta alrededor del espacio donde usted instalara su unidad debe

de estar plana y nivelada. (Vea el área sombreada en la ilustración

número 1).

2. Antes de instalar la unidad, mida la altura de los dos (2) lados de los

gabinetes (H1-4), frente y parte trasera (vea ilustración 1) del piso a

lo alto de la cubierta.

Ilustración 1

Ilustración 2

Reborde

de metal

Lime el

borde

levantado

para dejar

espacio

para una

unidad

1 ½" Max.

(3,8 cm Max.)

1/16" (0,16 cm) (vea ilustración 2).

4. Para modelos equipados con un sistema de dispositivo de nivelación: Quite y deshágase

de las dos patas ajustables traseras, solo sirven para sostener la unidad durante el

transporte.

5. Deslice la unidad hacia el gabinete. Asegúrese que la unidad este centrada con el centro

de la abertura del gabinete.

6. Remueva la parte en plástico extruido en cada lado de la cubierta

de vidrio (Algunos modelos).

7. Es imprescindible que el reborde de metal que se encuentra

debajo de la cubierta este sobre la cubierta del gabinete. La

cubierta no deberá tocar directamente la cubierta del gabinete

(vea ilustración 2). Nivele la unidad si es necesario.

3. Nivele la estufa usando

las 4 patas niveladoras de

manera que la altura del

piso a la supercie interior

de la cubierta es mayor

que la altura del gabinete

mas alto de su mobiliario

de cocina por lo menos por

Para instalar

exitosamente su

estufa, la medida

inicial del piso a la

supercie interior

de la cubierta

de vidrio debe

ser mayor que la

altura del gabinete

por lo menos 1/16"

(0,16 cm) como se

midió en el paso

número 2.

con la dimensión C.

8. Después de

la instalación,

ASEGÚRESE que

la unidad este

sostenida por las

patas niveladoras y

NO por la cubierta.

INSTRUCCIONES DE INSTALACIÓN DE COCINAS DE GAS DE 30"

(Modelos con quemadores sellados)

4½

10½

7½

2½

WALL

(76.2)

(5.1)

(30.5)

(12.7)

(19)

(11.4)

(15.2)

(7.6)

(6.4)

(26.7)

2½

(6.4)

(7.6)

(10.1)

(12.7)

Antesdecomenzar

Herramientas que va a necesitar

Para patas de nivelación y montura anti-vuelco:

● Llave ajustable o alicates

● Llave para apretar tuercas de 1/4" (7mm)

● Llave para apretar tuercas de 3/8" (10mm)

● Taladro eléctrico y una broca de

1/8" (broca de taladro de hormigón

de 5/32" si se instala sobre

hormigón)

● Nivel & Cinta de medición

Para la conexión al suministro de gas:

● Pinza

● Brocha

Paraelajustedelallamadelosquemadores:

● Destornilladores de estrella y de cabeza

plana

Para la conversión a gas (PL/Propano o gas natural):

● Llave de boca de 1/2"

Material adicional que va a necesitar:

● Válvula de desconexión de la línea de gas

● Sellador para uniones de tuberías que

resista la acción del gas propano/PL

● Un conducto de metal exible (½" NPT x

¾" o de ½" de D.I.) con diseño certicado

por CSA International. Ya que las

tuberías rígidas restringen el movimiento

de la cocina, se recomienda el uso de

tuberías exibles nuevas (de entre 1,20

a 1,50 mts) durante la instalación y cada

Construcción del armario

1.1

Para eliminar el riesgo de

quemaduras o de fuego tratando de alcanzar algo

por encima de las zonas calientes, evite de colocar

artículos sobre la cocina. Si cree necesitar este

espacio, el riesgo puede disminuir si instala un

sombrerete que proteja horizontalmente un mínimo de

5" (12,7 cm) sobre la base del armario.

1.2

Preparación del mostrador (Figura 1)

• Las extremidades de la cocina sobrepasan el borde de

su mostrador.

• Si tiene un mostrador con las extremidades

cuadradas (planas), no se necesita ninguna

preparación del mostrador.

• Elrebordedefrentedemostradoresmoldeados

deben tener bordes moldeados a 3/4" (1,9 cm) a partir

de cada extremidad de la apertura (Figura 1).

• Losmostradoresenazulejos deberán necesitar un

Figura 1

Mostrador moldeado

oenazulejorecortado

3/4" (1,9 cm) hacia atrás

en las esquinas de

frentedelaaberturadel

mostrador.

Anchura

de hueco

mín.

1.3

Preparación del suministro de gas y

eléctrico

• Las áreas rayadas son las ubicaciones en donde la

linea de gas puede entrar el armario (Figura 2).

• La posición recomendada para la entrada de la linea

de gas esta localizada a 7¼" (18,4 cm) de la pared

izquierda y a 2" (5,1 cm) del piso (Figura 2).

• El área sombreada es la localización en donde la

toma eléctrica puede encontrarse (Figura 2).

Posición

recomendada

Nota: Todas las dimensiones son en pulgadas

(centímetros).

Figura 2

recorte de 3/4" (1,9 cm) a partir de cada extremidad

y/o un borde redondeado aplanado (Figura 1).

• Sielanchodelaaberturadelmostradores

más grande que 30 1/16" (76,4 cm), ajuste a las

dimensiones como para el 3/4" (1,9 cm).

• Elmostradordebersernivelado. Coloque un

nivelador sobre el mostrador, primero de lado a lado

y luego del frente hacia atrás. Si el mostrador no está

nivelado, la cocina no estará nivelada. El horno debe

ser nivelado para tener resultados satisfactorios al

hornear. Las extremidades de la plancha de la cocinar

sobrepasan los bordes de la abertura del mostrador.

vez que se vaya a instalar de nuevo o se cambie de

lugar posteriormente.

● Utilice siempre los dos (2) adaptadores de campana

(½" NPT x ¾" o de ½" D.I.) que se suministran con

el conducto exible nuevo para la conexión de la

cocina.

La page charge ...

Kenmore FGGS3065PB Guide d'installation

Marque: Kenmore

Modèle: FGGS3065PB

Catégorie: Micro-ondes

Taper: Guide d'installation

Ce manuel convient également à

32673

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore FGGS3065PB Installation guide
español: Kenmore FGGS3065PB Guía de instalación

Kenmore FGGS3065PB Guide d'installation

Ce manuel convient également à

Kenmore FGGS3065PB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents