WASSERSTEIN Wireless Doorbell Chime Manuel utilisateur

Marque
WASSERSTEIN
Modèle
Wireless Doorbell Chime
Taper
Manuel utilisateur
Wireless Chime
USER MANUAL
In the Box
1 x wired transmitter
1 x USB power adapter
with 4 universal plugs
1 x wireless chime
1 x spade connector
cable (3.3 ft) 1 x wire connector
1 x back cover pin
1 x tinned cable
(0.3 ft)
2 x 3*20 mm
screws
Page 1
Overview
The Wasserstein Wireless Chime gives you a custom
wireless alert system for your Google Nest Doorbell
(battery and Google Nest Doorbell (wired), and features
seven pre-loaded tunes and four LED colors to choose
from.
Page 2
Safety Information
Read carefully before installing:
• Always wear suitable protective gear (e.g. safety
goggles) when drilling holes, etc.
• Before drilling holes in walls, check for electricity cables
and water pipes.
• Shut off the power to the doorbell transformer before
you attempt to connect or remove it. Locate and shut off
the circuit breaker switch of your home's main electricity
supply.
• Before touching any wires, use a voltage sensor to check
that the power is actually off – the sensor will alert you if
the wires are still live.
Understanding the Wireless Chime
1. Halo LED / notification
2. LED dimmer
3. Tune selection
4. Ambient light sensor
5. Volume up
6. LED brighter
7. Volume down
1 5
4
6
7
2
3
Page 3
Understanding the Wired Transmitter
Installation
Installing the Doorbell Transmitter
Choose a location that's nowhere near a heat or water
source, and that won't be hit when opening the door.
1. Remove the silicone stopper from the top of the
transmitter.
2. Use a pin to press the notch and remove the back cover.
1
2
3
1. Wired transmitter
2. Spade connector wire
3. AC power adapter
connector
Page 4
3. Screw the transmitter back cover onto the wall using
2 screws (3 x 20 mm) if necessary.
AC OUT AC INSWITCH
Inside Outside
Note: It is recommended that the transmitter be placed
under a covered area or inside the house at the
height between 4.5 ft to 6.0 ft.
Page 5
4. Connect the spade connector to the back of the
Nest Doorbell.
5. Connect the AC power terminals to the AC power
adapter connector (there is no polarization).
6. Follow instructions on the Google Home APP to set up
the chime type for your Nest Doorbell (battery) or
Nest Doorbell (wired).
AC OUT AC INSWITCH
Note: Transmitter is powered by 16-24 VAC AC adapter,
the AC adapter needs to meet the safety standard
requirements of IEC 62368-1, and the output power
needs to meet the PS2 level. Please see page 9 for
wire stripping instruction if the adapter comes with
spade connectors.
Page 6
Google Nest Doorbell Setup
1. Make sure the Google Nest Doorbell is connected to
Wi-Fi.
2. Go to "Settings" by clicking the gear symbol on the top
right.
3. Go to "Doorbell".
4. Make sure Ring indoor chime is "ON".
5. Press the doorbell and indoor chime will ring.
Note: Google Nest Doorbell might take a minute to
update the setting.
6. Confirm the transmitter and receiver is paired.
Page 7
Installing the Wireless Chime
Rotate clockwise until you hear the click to lock the plug in
place. Plug the chime into an AC outlet.
L
o
c
K
O
p
e
n
Setup and Operation
Transmitter and Receiver Pairing
1. Press and hold both of the brightness adjustment
buttons for 3 sec until the LED is blinking.
Page 8
2. Press the doorbell button / smart doorbell.
3. Wireless Chime will be paired with the Wireless
Transmitter.
Changing the Tune
Press the center button (Wasserstein logo) to change the
doorbell tune. (7 tunes)
Page 9
Adjusting the Volume
• Press the +/- button to adjust the volume level you want.
(6 levels)
• To mute the chime, press the - button until you cannot
hear the ring.
Changing the Halo LED Color
Press and hold the both center & volume down buttons
to change the halo LED color.
pinkblue white cyan
Color options:
Page 10
0.6
22
20
18
16
14
12
10
AWG
0.8
1.0
1.3
1.6
2.0
2.6
MM
How to strip a wire using a wire stripping tool
1. Get a wire stripping tool
labelled for your type of
wire.
CAUTION: Always wear protective gear and use proper
tools and techniques to avoid injury.
2. Find the notch that
matches your wire’s
gauge.
Change the Halo LED Brightness Adjustment
• LED will automatically turn on when the ambient light
goes down.
• Press the / button to adjust the brightness to your
preferred level. (7 Levels)
• To turn off halo LED, press the button until the halo
LED is off.
Additional Chime(s)
• You can connect up to 5 wireless chimes with a single
transmitter. Simply plug in the additional wireless chime
to the wall outlet and follow the pairing instructions.
• Each chime can be set with its own tune and LED color.
Page 11
How to strip a wire using a utility knife
1. Hold the utility knife so it
gently rests on the wire.
2. Roll the wire under the
blade to score the
insulation.
Note: Use protective gear when using a utility knife.
0.6
22
20
18
16
14
12
10
AWG
0.8
1.0
1.3
1.6
2.0
2.6
MM
4. Squeeze the stripping
tool’s handles gently.
5. Spin the tool around the
wire to ensure you’ve cut
the insulation.
6. Slide the stripper off
the wire to pull off the
insulation.
3. Place the tip of the wire
in the appropriate notch.
Page 12
3. Bend the wire at the scored line and break off the
insulation.
2. Insert the tinned cable
into one side.
(There is no polarity)
AC Adapter Connector
1. Open up the notches
on the connector
CAUTION: Always wear protective gear and use proper
tools and techniques to avoid injury.
4. Insert the AC power
adapter cable to the
other end and repeat
step 3.
3. Close the notches on
the connector and make
sure the cable is tightly
clamped.
Page 13
Battery warning
CAUTION: Risk of fire or explosion if the battery is replaced
by an incorrect type.
WARNING:
– replacement of a battery with an incorrect type may defeat a
safeguard;
– disposal of a battery into fire or a hot oven, or mechanically
crushing or cutting of a battery, may result in an explosion;
– leaving a battery in an extremely high temperature
surrounding environment, such as sunshine, fire, or hot
surface may result in an explosion or the leakage of flammable
liquid or gas;
– a battery subjected to extremely low air pressure may result
in an explosion or the leakage of flammable liquid or gas.
Page 14
FCC Caution
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference,and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV
technician for help.
Page 15
RF Warning for Mobile Device
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
IC Caution
RSS-Gen Issue 5 April 2018 & CNR-Gen 5e édition Avril 2018
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the device.
English:
RF Warning for Mobile Device
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
Avertissement RF pour appareil Mobile
French:
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux
1.L’appareil ne doit pas produire de brouillage;
2.L’appareil doit accepter tout brouillage radioélectrique subi,même
si le brouillage est susceptible d’en compromettre le fonctionnement.
deux conditions suivantes :
Cet équipement est conforme aux limites d’exposition au
Cet équipement Devrait être installé et exploité avec une
distance minimale 20cm entre le radiateur et votre corps.
rayonnement IC Partez pour un environnement .
incontr lé
Page 16
Page 17
Specifications
Wired Transmitter
Product Dimension:
Product Weight:
Material:
Power in:
RF frequency:
Wireless range:
Operating Temperature:
Pair max wireless chimes:
Wireless Chime
Product dimension:
Product weight:
Material:
Power supply:
Power input:
Power output:
RF frequency:
Wireless range:
Operating Temperature:
Chime tunes:
Chime volume:
Sound Level:
LED Night Light Brightness:
LED Colors:
3.15 x 1.57 x 0.85 in
1.5 oz
ABS plastic
16 - 24 VAC,
Class 2 transformer
433 MHz
650 ft
32 °F to 104 °F
5 wireless chimes
5.08 x 2.36 x 1.39 in
5.0 oz
ABS plastic
USB power adapter
100‐240 VAC 50/60 Hz
5 V 1 A
433 MHz
650 ft
32 °F to 104 °F
7 tunes
6 levels
mute to 110 dB
7 levels
white / blue / pink / cyan
Operating ambient temperature: 0 - 40°C
Storage and transportation ambient temperature: -20 - 60°C
Altitude not higher than 5000m
Google Nest Doorbell (battery) &
Nest Doordbell (wired is not included.
Google Nest Doorbell (battery), Nest
Doordbell (wired Google Nest, Google,
Google logo, related marks and logos are
trademarks of Google LLC.
Wasserstein is not affiliated with Google LLC.
Wasserstein is a trademark of Dropcases Ltd.
Made in China
Get More Support
Scan the QR code below or email us at
[email protected].
www.wasserstein-home.com
This product has been certified by Wasserstein to meet
Google’s compatibility standards. Google is not responsible
for the operation of this product or its compliance with any
applicable safety or other requirements.
Learn more at g.co/madeforgoogle
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

WASSERSTEIN Wireless Doorbell Chime Manuel utilisateur

Marque
WASSERSTEIN
Modèle
Wireless Doorbell Chime
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents