Newage 56 Manuel utilisateur

INSTALLATION AND OPERATION GUIDE

ATTENTION: Is your Work Table damaged?

Need help or spare parts? For fastest service,

contact NewAge Products at 1-877-306-8930;

or suppor[email protected]om.

Do not return to the retailer.

STOP

Use two or more people to move, assemble, or install the worktable to

avoid back injury. Do not leave children unattended near the worktable.

Warning: Excessive weight hazard!

!

MANUAL ADJUSTABLE HEIGHT

WORK TABLE

IM-PB3.201A-02

Index

Unpacking 3

Product Inspection 3

Additional Tools Needed 3

Worktops 4

Accessories 4

Product Specications 5

Parts Supplied 6

Hardwares 8

Worktop Frame Assembly 9

Installing the Lifting Columns 10

Installing the Feet & Transmission Rod 11

Assembling Transmission Tube Cover 13

Installing Support Beams 14

Installing the Crank Holder 15

Crank Handle Instructions 16

Accessory Installation 17

Maintenance and Care 18

Manufacturer Warranty 19

3

Unpacking

• Begin by placing the package on a covered at surface.

• Remove all cardboard, foam packaging material and nylon bags.

• Dispose / recycle all packaging materials.

• Verify all the contents in the box and gather the required tools. See “Tools Needed” in the list on

next pages.

Product Inspection

• Check to see if all the parts are received as per

the order.

• Contact NewAge Products at 1-877-306-8930;

for any missing parts.

• Inspect the products for any damages before

starting the installation.

• Go through the installation instructions carefully

before starting the installation.

• Two or more persons are required to install the worktable shown in this Installation Manual.

• The illustrations shown in this Install Manual are for representation purpose only. Actual sizes of

the parts supplied in the package can be slightly dierent by appearance. Appearance of

hardware sizes are enlarged for ease of understanding for the customer.

IMPORTANT NOTES

Additional Tools Needed

#2 Philips

Screw Driver

4

Worktop

SKU 32011

56 in. Bamboo Worktop

SKU 32111

56 in. Stainless Steel Worktop

SKU 48080

Adjustable Height Work Table

Drawer

Weight Capacity - 55 lbs

Accessories

22”

8.6”

1.9”

5

500 lbs.

Product Specications

29.5”

44.1”

Manual Adjustable Height Work Table

23.6”

SKU 48041

56 in. Manual Adjustable Height Work Table

26.8”

39.8”

Work Table Max Height - 44.1”

Work Table Min Height - 29.5”

Height Adjustments - 14.6”

Adjustment Speed - 7.5cm/turn

Weight Capacity - 500lbs

6

Parts Supplied & Spare Parts

15

12

11

13

14

5

3

1

2

16

17

6

18 19

4

20

21

7

Parts Supplied & Spare Parts

S. No. Engg Part No. Description BOM

Qty

Spare

Part SKU

Spare

Part Qty

1 H00706A-01 Button Head Hex Screw M5x6 1

48082 Pack of 1

2 H00707A-01 Button Head Hex Screw M6x10 6

3 H00691A-01 Button Head Hex Screw M6x16 20

4 H00692A-01 Hex Head Bolt M8x16 4

5 H00693A-01 Button Head Hex Screw M8x30 4

6 H00694A-01 Button Head Hex Screw M6x30 8

7 H00703A-01 M8 Wrench -Number 13 1

8 H00708A-01 Allen Key 3x3 1

9 H00698A-01 Allen Key 4x4 1

10 H00699A-01 Allen Key 5x5 1

11 PB3-201.001A-01-XX Adjustable Work table Base for Crank 1 - -

12 PB3-201.02A-01-XX Adjustable Worktable Crank 1 - -

13 PB3-202.001A-01-XX Adjustable Work table Supporting Tube

Welding Assembly 2 - -

14 PB3-204.001A-01-XX Adjustable Work table Supporting beam

Welding Assembly - 56in 2 - -

15 PB3-201.003A-01-XX Adjustable Work table Crank Right lifting

column Assembly 1 - -

16 PB3.202.004A-01-XX Adjustable Work table Left Lifting Column

Assembly 1 - -

17 PB3.202.005A-01-XX Adjustable Work table Foot Assembly 2 - -

18 PB3-204.002A-01-XX Adjustable Work table Supporting Beam

for Leg Welding Assembly - 56 in 1 - -

19 PB3- 204.003A-01-XX Adjustable Work table Cover - 56 in 1

20 PB3- 204.004A-01-XX Adjustable Work table Transmission Rod -

56 in 1 - -

21 H00656A-01 M6 Wood Flush Tapping Insert 20 48081 1

8

Hardwares

6x Button Head Hex

Screw M6x10 (B)

4x Hex

Head Bolt M8x16 (D) 4x Button Head Hex

Screw M8x30 (E)

8x Button Head

Hex Screw M6x30

(G)

20x Button Head

Hex Screw M6x16 (A)

1x Button Head Hex

Screw M5x6 (C)

13mm Wrench

(F)

5x5 4x4 3x3

Allen Key (H)

9

Worktop Frame Assembly

Install the desk frame assembled in Step 1 on the tabletop using screws(A). Tighten

screw with a 4x4 allen key.

2

Parts required.

4 x M8x30 Button

Hex Head Screws (E)

12 x Button Hex Head

Screws M6x16 (A) Allen Key 4x4

Allen Key 5x5

1Attach the desk frame beam tube to the desk frame support tube using screw(E).

Tighten the screws with a 5 x 5 allen key.

X12

10

Installing the Lifting Columns

Connect the right & left lifting columns to the desk frame beam tube using screws.

Tighten the screws(A) with a 4 x 4 allen key.

3

Parts required.

8 x M6x16 Button

Hex Head Screws

(A)

Allen Key 4x4

Maintain consistent heights of the left and

right lifting columns during the installation.

ATTENTION

X8

NOTE:

The supporting beam should

be facing opposite side of the

NewAge logo.

11

Installing the Feet & Transmission Rod

Connect the left and right columns to

the feet. Tighten the screws(G) with a

4x4 allen key.

Insert one end of the transmission hexagonal rod in the right lifting column , the closest

to the NewAge logo.

4

5

Parts required.

8 x M6x30 Button

Head Hex Screws

(G)

Allen Key 4x4

NOTE:

The transmission rod can be inserted to the left lifting column, however, in that assembly crank will

be positioned left side of the table and up and down rotation will be inverted.

12

Installing the Transmission Rod Contd.

Insert the other end to the left column.

6

7

Parts required.

1 x M5x6 Button

Head Hex Screw (C)

Allen Key 3x3

Align the hexagonal rod end with the

hole position in the left column by

rotating.

8Tighten the rod with screw(C) using a

3x3 allen key.

13

Assembling Transmission Tube Cover

Connect the cover to the left and right columns using screws. Tighten the screws (B)

with a allen key.

9

Parts required.

6 x M6x10 Button

Head Hex Screws (B)

Allen Key 4x4

14

Remove the decorative cover on the

support beam.

10

Parts required.

Installing Support Beam

4 x M8x16 Hex

Headed Bolts

(D)

13mm Wrench

(F)

Reassemble the decorative cover on

the support beam.

12

Assemble the support beam with the

bolts(D) to the left and right columns

using wrench.

11

15

Use 4x4 allen keys to uninstall the screws.

13

Parts required.

Installing the Crank Holder

Allen Key 4x4

Insert the Crank holder to the transmission

rod on the right column. Tighten the

screws with allen key.

14

Make sure that arrow on crank

holder is UP

ATTENTION

Insert the Crank to the crank holder as

shown below.

15

16

Rotate the crank in circular motion to

increase or decrease the height of the

table.

2

Pull out the crank handle when in use, push the crank inwards to lock it after use.

1

DOWN UP

Crank Handle Instructions

Pull out to use Push in to lock

When mechanism is locked, do not rotate the crank as this can cause damage to the mechanism.

Always unlock the crank before rotating it.

ATTENTION

17

Accessory Installation

Install the drawer to the table top with the screws. Tighten the screws with allen key.

1

Parts required

4 x M6x16

Button Head Hex Allen Key 4x4 Pull out Drawer

18

Maintenance and Care

1. The steel in this product has been coated with industrial grade powder coating for a

durable nish. To prevent any damage to this nish, do not allow harsh chemicals such

as oils and grease to remain on the powder coating surface. Use a glass cleaner to clean

and maintain all powder coated surfaces.

2. Our wood top is made from Bamboo, with a polyurethane coating to help protect it

and extend its usage. It can be cleaned using a gentle household cleaner. Do not allow

chemicals, water, or other substances to remain on the wood top for extended periods

of time to reduce the risk of damage or stains.

3. When using our stainless-steel tops, do not allow harsh chemicals such as oils and

grease to remain at the worksurface for an extend period, to prevent stains and damage

to the top

4. Make sure to check once a year all the gears and moving parts for dirt and lubrication.

19

Scan this QR code with the camera

on your mobile device to visit the

NewAge Products Support Hub

www.newageproducts.com/support-hub/

Register your NewAge Products purchase online for quicker

customer assistance and access to exclusive beneﬁts

Visit www.newageproducts.com/register/

Warranty Claim

For warranty service please contact NewAge Products at

1-877-306-8930; or [email protected]

Please review all warranty details below, prior to

contacting NewAge Products for a claim.

Scan the QR code on the right to access our support page or

visit www.newageproducts.com/contact-us/

PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available

when you call our customer service team:

• Name, address and telephone number

• Product Name / SKU Number

• A clear, detailed description of the problem

• Proof of purchase including order number

FIVE YEARS LIMITED WARRANTY

WHAT IS COVERED

When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products

Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for the warranty duration from the

purchase date of the product.

1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.

2. Damage resulting from improper handling, or products damaged by accident, misuse, abuse, ﬁre, ﬂood, improper installation, acts of God,

neglect, corrosion, modiﬁcation or mishandling.

3. Products damaged by improperly loading beyond the speciﬁed maximum weight capacity outlined in the instructions provided with the prod-

uct.

4. Repairs or replacement when your product is used in other than normal, single-family household use, such as a commercial environment, or

handled in anyway inconsistent with the installation instructions included with the product.

5. Cosmetic damage, including scratches, dings, dents or cracks in paint that do not aect the structural or functional capability of the product.

6. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.

7. Replacement parts for NewAge products outside Canada and the United States.

8. Loss of product contents due to theft, ﬁre, ﬂood, accident or acts of God.

9. Shipping or freight fees to deliver replacement products or to return defective products.

10. Any labor costs during the limited warranty period.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR

THE SHORTEST PERIOD ALLOWED BY LAW. THIS WARRANTY IS LIMITED TO THE ORIGINAL BUYER. Some states and provinces do not allow limitations

on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you. This warranty gives you speciﬁc legal rights, and

you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AT OUR DISCRETION AS

PROVIDED HEREIN. NEWAGE SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you speciﬁc

legal rights, and you also may have other rights that vary from state to state or province to province.

WHAT IS NOT COVERED

NEWAGE PRODUCTS INC.WORKTABLE

MANUFACTURER WARRANTY