Audio-Technica audio-technica Cardioid Condenser USB Microphone Manuel utilisateur
- Catégorie
- Microphones
- Taper
- Manuel utilisateur
Ce manuel convient également à
AT2020USB+
Instruction Manual
AT2020USB+
Cardioid Condenser USB Microphone
Contents
Introduction & features 3
Setting up your microphone with pivot mount & desk stand 4
Preliminary setup with Mac OS X 5
Preliminary setup with Windows 7 7
Using headphones 10
Using mix control 10
Selecting software 10
Setting your software levels 10
Positioning your microphone 10
Protecting your microphone 10
Specifications 11
2
FCC Notice
Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Caution
You are cautioned that any changes or modifications not expressly approved in this manual could
void your authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
IC statement
CAN ICES-3 (B) / NMB-3 (B)
3
Thank you for buying the Audio-Technica AT2020USB+ Cardioid Condenser USB Microphone.
Equipped with a USB output, this microphone is designed for digitally capturing music or any acoustic
audio source using your favorite recording software. The AT2020USB+ offers studio-quality articulation
and intelligibility perfect for home studio recording, field recording, podcasting, and voiceover use.
The AT2020USB+ features a built-in headphone jack with volume control that allows you to directly
monitor your microphone signal with no delay. It also offers mix control that blends microphone and
pre-recorded audio. The microphone’s cardioid pickup pattern delivers excellent off-axis rejection,
while its A/D converter with a 16-bit, 44.1/48 kHz sampling rate ensures extremely articulate sound
reproduction.
Audio-Technica’s state-of-the-art design and manufacturing techniques ensure that the microphone
complies with the company’s renowned consistency and reliability standards.
Features
• Condenser microphone with USB output for digital recording
• High quality A/D and D/A converter with 16 bit, 44.1/48 kHz sampling rate for superb audio
• Headphone jack with volume control allows you to monitor the microphone signal with no delay
• Mix control allows you to blend your microphone signal and pre-recorded audio
• High-output internal headphone amplifier delivers superior clarity and musical detail as well as
more volume overall
• Smooth, extended frequency response ideally suited for podcasting, home studio recording,
field recording and voiceover use
• Compatible with Windows 7, 8, 8.1,10 and Mac OS X
• Tripod desk stand with folding legs for secure and easily portable tabletop use
Introduction
4
1. Capsule — Condenser microphone element with cardioid polar pattern
2. Blue LED — Blue light shows microphone is receiving USB power
3. Headphone Level Control — Dial controls headphone volume
4. Mix Control — Blends microphone and pre-recorded audio
5. Headphone Jack — 1
/8-inch (3.5 mm) stereo jack for connecting your headphones
6. Metal Construction — Tough, durable, resilient design
7. USB Connector — Use the included USB cable to connect AT2020USB+ to your Mac or PC
8. USB Cable
Setting up your microphone with included pivot mount and tripod desk stand
A. Screw the pivot mount onto the top of the tripod desk stand.
B. Place the tripod desk stand on a flat surface. (The tripod legs will extend to provide a wide,
secure base.)
C. Install the AT2020USB+ microphone into the threaded collar of the pivot mount and tighten
collar while holding the microphone in place. The front of the microphone should be facing the
sound source. (A USB icon and blue LED indicate the front of the microphone; the product model
number is displayed on the rear of the microphone.)
D. If necessary, adjust the microphone’s angle with the pivot mount’s thumbscrew.
E. Plug the provided USB cable into the USB digital output at the base of the microphone.
Note: Many recording software programs are available online. Audacity is widely used free software
for recording and editing sounds. It is available online at http://audacity.sourceforge.net/
AT2020USB+
1
6
3
4
7
5
(on back)
2
8
5
1. Plug the free end of the provided USB cable into the USB port on your computer. The microphone’s
blue LED will illuminate, indicating the microphone is receiving power. Your computer will
automatically recognize the USB device and install a driver.
2. To select the AT2020USB+ as your audio input, first, open your System Preferences.
3. Next, click Sound to display the Sound preference pane.
Preliminary setup with Mac OS X
AT2020USB+ USB
4. Click the Input tab and select the AT2020USB+ as the device for sound input.
6
Preliminary setup with Mac OS X (continued)
5. Click the output tab and make certain AT2020USB+ is selected as the default output device.
(This should have happened automatically.)
Your preferences are now set to use the AT2020USB+ on your Mac with GarageBand or another
recording program of your choice.
AT2020USB+ USB
7
1. Plug the free end of the USB cable into the USB port on your computer. The microphone’s blue
LED light will illuminate, indicating the mic is receiving power. Your computer will automatically
recognize the USB device and install a driver.
2. In the lower right portion of your screen you may get a message that new hardware was found;
or you may see a driver software installation notice.
3. Start menu > Control Panel > Sound
To select the AT2020USB+ as your default recording device, begin at your Start menu.
Select Control Panel.
Preliminary setup with Windows 7
8
Preliminary setup with Windows 7 (continued)
4. Select Sound.
5. The following screen will pop up:
9
6. Select the Recording tab, and choose AT2020USB+ as the default device.
7. Double click on the AT2020USB+ icon to open the Microphone Properties window. Select the
Levels tab to adjust microphone level (loudness). You may need to come back to this window to
readjust the level after you begin recording.
Your preferences are now set to use the AT2020USB+ with Windows 7 and the recording program of
your choice.
Microphone
AT2020USB+
Default Device
10
Additional Information
Using headphones
Warning: Turn the volume control down before using the headphones.
The 1
/8" (3.5 mm) headphone jack on the rear of the microphone allows you to directly monitor your
recording without the delay that occurs when monitoring through your computer’s headphone output.
When your preliminary setup is completed, and your USB microphone is connected to your computer’s
USB port (the microphone’s blue LED is illuminated), plug your headphones into the headphone jack
on the rear of the microphone. While talking into the microphone, you should hear yourself in the
headphones. (If Mix Control is set on COM you may not be able to hear yourself. Set Mix Control
between COM and MIC to assure you will be able to hear live audio through your headphones.)
Adjust the volume by rotating the Headphone Level Control dial on the front of the microphone.
Note: The Headphone Level Control dial only adjusts the volume of the mic’s headphone output; it
does not adjust the microphone level.
Note: The AT2020USB+ is equipped with a high-output internal headphone amplifier that provides
superior clarity and musical detail as well as more volume overall.
Using Mix Control
The AT2020USB+ allows you to monitor previously recorded tracks while recording new audio. Adjust
the Mix Control to balance levels of live audio from your microphone and pre-recorded audio on your
computer. Turn the Mix Control dial towards COM (computer) to hear more pre-recorded audio; turn
the dial towards MIC (microphone) to hear more of your voice or instrument in the mix.
Selecting software
You have many choices in recording software. Audacity, available for free online at
http://audacity.sourceforge.net/, is a widely used software program that provides basic recording software.
Setting your software levels
Correct adjustment of microphone level is important for optimum performance. Ideally, the microphone
level should be as high as possible without overloading the input of your computer. If you hear
distortion, or if your recording program shows levels that are consistently overloaded (at peak levels),
turn the microphone volume (or level) down, either through your control panel (or system preferences)
settings, or through your recording software. If your recording program shows insufficient level, you
can increase the microphone gain either from the control panel (or system preferences) settings or
through your recording program.
No further microphone level adjustments should be needed, as long as the acoustic input does not
change significantly.
Positioning your microphone
It is important to position the microphone directly in line (on axis) with the person speaking/ singing or
instrument (or other sound source) to achieve the best frequency response of the microphone.
For use in speaking/singing applications, the ideal placement for the microphone is directly in front of
the person speaking/singing. The same placement is optimal when miking an instrument such as an
acoustic guitar, drums or piano. Experiment with different mic placements to find the best sound for
your particular setup.
Protecting your microphone
Avoid leaving your microphone in the open sun or in areas where temperatures exceed 110° F (43° C)
for extended periods. Extremely high humidity should also be avoided.
11
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Cardioid
Frequency Response: 20 – 20,000 Hz
Power Requirements: USB Power (5V DC)
Bit Depth: 16 bit
Sample Rate: 44.1/48 kHz
Controls: Mix control; Headphone volume control
Weight: 386 g (13.6 oz)
Dimensions: 162.0 mm (6.38") long, 52.0 mm (2.05") maximum body diameter
Output Connector: USB-type
Headphone Output Power: 130 mW (at 1 kHz, 10% T.H.D., 32 ohm load)
Headphone Jack: 3.5 mm (1/8") TRS (stereo)
Accessories Included: Pivoting stand mount for 5/8"-27 threaded stands; 5/8"-27 to 3/8"-16 threaded
adapter; soft protective pouch; tripod desk stand; 10' (3.1 m) USB cable
System Requirements: Macintosh: Mac OS X; USB 1.0 or 2.0; 64 MB RAM (minimum)
Windows: Windows 7, 8, 8.1,10 ; USB 1.0 or 2.0; 64 MB RAM (minimum)
†In the interest of standards development, A.T.U.S. offers full details on its test methods to other industry professionals on request.
Specifications are subject to change without notice.
AT2020USB+ Specifications†
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
SCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚ 0˚
150˚
120˚
90˚
30˚
60˚
0°, 50cm
LEGEND
Frequency in Hertz
Response in dB
10 dB
100
50 200 10k
5k
1k
500 2k 20k
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
SCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚ 0˚
150˚
120˚
90˚
30˚
60˚
0°, 50cm
LEGEND
Frequency in Hertz
Response in dB
10 dB
100
50 200 10k
5k
1k
500 2k 20k
Frequency Response
Polar Pattern
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2017 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com
P52458 ver.1 2012.11.01
149405940-01-02 ver.2 2017.07.20
To reduce the environmental impact of a multi-language printed document, product information is
available online at www.audio-technica.com in a selection of languages.
An de réduire l’impact sur l’environnement de l’impression de plusieurs, les informations concernant
les produits sont disponibles sur le site www.audio-technica.com dans une large sélection de langue.
Para reducir el impacto al medioambiente, y reducir la producción de documentos en varios leguajes,
información de nuestros productos están disponibles en nuestra página del Internet:
www.audio-technica.com.
AT2020USB+
To reduce the environmental impact of a multi-language printed document, product information is available online at
www.audio-technica.com in a selection of languages.
An de réduire l’impact sur l’environnement de l’impression de plusieurs langues, les informations concernant les produits sont
disponibles sur le site www.audio-technica.com dans une large sélection de langue.
Para reducir el impacto al medioambiente, y reducir la producción de documentos en varios leguajes, información de nuestros productos
están disponibles en nuestra página del Internet: www.audio-technica.com.
Para reduzir o impacto ecológico de um documento impresso de várias linguas, a Audio-Technica providência as informações dos seus
produtos em diversas linguas na www.audio-technica.com.
Per evitare l’impatto ambientale che la stampa di questo documento determinerebbe, le informazioni sui prodotti sono disponibili online in
diverse lingue sul sito www.audio-technica.com.
Der Umwelt zuliebe nden Sie die Produktinformationen in deutscher Sprache und weiteren Sprachen auf unserer Homepage:
www.audio-technica.com.
Om de gevolgen van een gedrukte meertalige handleiding op het milieu te verkleinen, is productinformatie in verschillende talen “on-line”
beschikbaar op: www.audio-technica.com.
Warranty (Please be sure to read the notes below.) For USA only
End-User LIMITED WARRANTY information for the USA is available at www.audio-technica.
com/usawarranties. You may also contact Audio-Technica U.S., Inc. to request a written copy of
the Limited Warranty at 1-330-686-2600 or via mail at 1221 Commerce Drive, Stow, OH 44224.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Audio-Technica audio-technica Cardioid Condenser USB Microphone Manuel utilisateur
- Catégorie
- Microphones
- Taper
- Manuel utilisateur
- Ce manuel convient également à