GE 40374 Manuel utilisateur

GE Home Generator Systems

Generator System

Model 040350 and Model 040374

Operator’s Manual

NOT

for

REPRODUCTION

2

Thank you for purchasing this quality-built GE generator. We’re pleased that you’ve placed your confidence in the GE

brand. When operated and maintained according to the instructions in this manual, your home generator will provide

many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with standby

generators and how to avoid them. Because we do not necessarily know all the applications this equipment could

be used for, it is important that you read and understand these instructions thoroughly before attempting to start or

operate this equipment. This product is only for use as an optional generator system which provides an alternate source

of electric power and to serve loads such as heating, refrigeration systems, and communication systems that, when

stopped during any power outage, could cause discomfort or inconvenience.

Save these instructions for future reference.

This home standby generator requires professional installation before use. Refer to the separate installation manual

for full information. Your installer should follow the instructions completely.

Where to Find Us

You never have to look far to find GE support and service for your generator. For quick service when you need it, keep

your original receipt with this manual. You may contact Customer Service at (888) 575-8226, or click on SERVICE &

SUPPORT at www.homestandbygeneratorsystems.com, which provides a list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

DATE OF PURCHASE

GENERATOR

Model Number

Model Revision

Serial Number

ENGINE

NOT

for

REPRODUCTION

3

Table of Contents

Safety Rules................................................4

Installation ................................................7

Generator Location ...................................................9

Delivery Inspection ..................................................10

Controls ..................................................11

Access Panels .......................................................12

System Control Panel ................................................14

Operation.................................................18

Automatic Operation ................................................19

Setting Exercise Timer ...............................................19

Wireless Monitor ....................................................20

Maintenance ..............................................23

Servicing the System.................................................23

Service Code Detection System .......................................23

Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Generator Maintenance..............................................25

Engine Maintenance .................................................27

When Calling for Assistance ..........................................31

Storage.............................................................31

Troubleshooting ..........................................32

Limited Warranty..........................................36

Speciﬁcations .............................................38

NOT

for

REPRODUCTION

4

Safety Rules

Explosion

Fire

Electrical Shock

Rotating Parts

Hot Surface

Toxic Fumes

Chemical BurnExplosive PressureAuto Start

Lift Hazard

Read Manual

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a degree

or level of hazard seriousness. A safety symbol may be used

to represent the type of hazard. The signal word NOTICE is

used to address practices not related to personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

Important Safety Instructions

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and the tags and decals affixed to the unit

are, therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the generator system unsafe.

WARNING The engine exhaust from this product contains

chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

WARNING Certain components in this product and related

accessories contain chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm. Wash

hands after handling.

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventilation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be drawn

into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Smoke alarms cannot detect carbon

monoxide gas.

NOT

for

REPRODUCTION

5

WARNING Unintentional sparking could cause fire or electric

shock resulting in death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR GENERATOR

• Disconnect the spark plug wire from the spark plug and place the

wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Storage batteries give off explosive hydrogen gas

during recharging.

Slightest spark will ignite hydrogen and

cause explosion, resulting in death or

serious injury.

Battery electrolyte fluid contains acid and is extremely caustic.

Contact with battery contents could cause severe chemical burns.

A battery presents a risk of electrical shock and high short

circuit current.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit cigarette during

and for several minutes after charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber boots and

rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

WARNING Generator produces hazardous voltage.

Failure to properly ground generator could result

in electrocution.

Failure to isolate generator from utility power could result

in death or serious injury to electric utility workers due to

backfeed of electrical energy.

• When using generator for backup power, notify utility company.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce the risk of a shock hazard.

• DO NOT allow unqualified persons or children to operate or

service generator.

• In case of an accident caused by electrical shock, immediately

shut down the source of electrical power and contact the local

authorities. Avoid direct contact with the victim.

• Despite the safe design of the residential generator, operating

this equipment imprudently, neglecting its maintenance or being

careless could cause possible injury or death.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• Before performing any maintenance on the generator, disconnect

the battery cable indicated by a NEGATIVE, NEG or (-) first. When

finished, reconnect that cable last.

• After your system is installed, the generator may crank and start

without warning any time there is a power failure. To prevent

possible injury, always set the generator’s system switch to OFF,

remove the service disconnect from the disconnect box AND

remove the 15 Amp fuse BEFORE working on the equipment.

WARNING Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or

explosion resulting in death or serious injury.

• Install the fuel supply system according to NFPA 37 and other

applicable fuel-gas codes.

• Before placing the generator into service, the fuel system lines

must be properly purged and leak tested.

• After the generator is installed, you should inspect the fuel

system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or other

explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any oil spills

immediately. Ensure that no combustible materials are left in the

generator compartment. Keep the area near the generator clean

and free of debris.

NOT

for

REPRODUCTION

6

WARNING Starter and other rotating parts could entangle

hands, hair, clothing, or accessories resulting in

serious injury.

• NEVER operate generator without protective housings, covers, or

guards in place.

• DO NOT wear loose clothing, jewelry or anything that could be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control panel and

disconnect Negative (NEG or -) battery cable.

CAUTION Installing the 15A fuse could cause the engine

to start at any time without warning resulting in minor or

moderate injury.

• Observe that the 15 Amp fuse has been removed from the control

panel for shipping.

• DO NOT install this fuse until all plumbing and wiring has been

completed and inspected.

CAUTION Excessively high operating speeds could result in

minor injury and/or equipment damage.

Excessively low speeds impose a heavy load on generator.

• DO NOT tamper with governed speed. Generator supplies correct

rated frequency and voltage when running at governed speed.

• DO NOT modify generator in any way.

NOTICE Improper treatment of generator could damage it and

shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact your

authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating air is

critical for correct generator operation.

• The access panels/door must be installed whenever the unit

is running.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a step. Stepping

on the unit could cause stress and break parts. This may result in

dangerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.

• If connected devices overheat, turn them off and disconnect them

from generator.

• Shut off generator and contact an authorized dealer if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

-unit makes unusual noises.

WARNING Exhaust heat/gases could ignite combustibles or

structures resulting in death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must have at least

5 ft (1.5m) minimum clearance from any structure, shrubs, trees or

any kind of vegetation.

• Standby generator weatherproof enclosure must be at least 5 ft

from windows, doors, any wall opening, shrubs or vegetation over

12 inches (30.48cm) in height.

• Standby generator weatherproof enclosure must have a minimum

of 5 feet (1.5m) overhead clearance from any structure, overhang

or trees.

• DO NOT place weatherproof enclosure under a deck or other type

of structure that may confine airflow.

• USE ONLY flexible steel fuel line provided. Connect provided fuel

line to generator, DO NOT use with or substitute any other flexible

fuel line.

• Smoke detector(s) MUST be installed and maintained indoors

according to the manufacturer’s instructions/ recommendations.

Carbon monoxide alarms cannot detect smoke.

• Keep at least minimum distances shown in Generator Placement

to insure for proper generator cooling and maintenance

clearances.

• It is a violation of California Public Resource Code, Section 4442,

to use or operate the engine on any forest-covered, brush-

covered, or grass-covered land unless the exhaust system is

equipped with a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states or federal

jurisdictions may have similar laws.

Contact Briggs and Stratton, retailer, or dealer to obtain a spark

arrester designed for the exhaust system installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

NOT

for

REPRODUCTION

7

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand Owner Orientation in this manual

before contracting or starting your generator installation.

To arrange for proper installation, contact the store at

which you purchased your generator, your dealer, a licensed

electrician or your utility power provider.

The generator warranty is VOID unless the system is

installed by licensed electrical and plumbing professionals.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

The Emission Control System for this generator is warranted

to standards set by the U.S. Environmental Protection Agency

and by the California Air Resources Board (CARB).

For the Home Owner

If you need more information in this matter, please call

888 575‑8226 between 8:00 AM and 5:00 PM CT.

For most applications, the installation manual contains

all the information required to properly install and start

the generator. This operator’s manual describes routine

operation and owner maintenance procedures.

For the Installing Dealer/Contractor

Installation

We sincerely appreciate your patronage. For this reason, we

have made every effort to provide for a safe, streamlined

and cost-effective installation. Because each installation is

unique, it is impossible to know of and advise the trade of all

conceivable procedures and methods by which installation

might be achieved. Neither could we know of possible

hazards and/or the results of each method or procedure. For

these reasons,

Only current licensed electrical and plumbing

professionals should attempt home generator system

installations. Installations must strictly comply with all

applicable codes, industry standards and regulations.

Your home generator is supplied with this “Operator’s

Manual” and a separate “Installation Manual”. These are

important documents and should be retained by the owner

after the installation has been completed.

This product is only for use as an optional generator system

which provides an alternate source of electric power and

to serve loads such as heating, refrigeration systems, and

communication systems that, when stopped during any

power outage, could cause discomfort or inconvenience.

NOTICE This product does NOT qualify for either an

emergency standby or legally required standby system as

defined by NFPA 70 (NEC).

 • Emergencygeneratorsystemsareintendedto

automatically supply illumination, power, or both,

to designated areas and equipment in the event of

failure of the normal supply. Emergency systems may

also provide power for such functions as ventilation

where essential to maintain life, where current

interruption of the normal supply would produce

serious life safety or health hazards.

 • LegallyRequiredstandbygeneratorsystemsare

intended to automatically supply power to selected

loads in the event of failure of the normal source

which could create hazards or hamper rescue or fire-

fighting operations.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

Only current licensed electrical and plumbing professionals

should attempt home generator system installations.

Installations must strictly comply with all applicable codes,

industry standards, laws and regulations.

NOT

for

REPRODUCTION

8

Power Decrease at High Altitude or

High Temperature

Air density is less at high altitudes, resulting in less available

engine power. Specifically, engine power will decrease 3.5%

for each 1,000 feet (300 meters) above sea level and 1%

for each 10° F (5.6°C) above 77°F (25°C). Make sure you and

your installer consider these factors when determining total

generator load.

Remember that as the distance from the existing electrical

service and gaseous fuel supply increases, and the

number of 90 degree bends in the fuel supply increases;

compensations in piping and wiring materials must be made.

This is necessary to comply with local codes and overcome

electrical voltage drops and gaseous fuel pressure drops.

The factors mentioned above will have a direct affect on

the overall price of your generator installation.

In some areas you may need to acquire electrical permits for

installing the home generator, building permits for installing

gas lines, and permits for noise allowances. Your installer

should check your local codes AND obtain the permits before

installing the system.

This section provides generator owners with the information

necessary to achieve the most satisfactory and cost effective

installation possible.

Federal and local codes, appearance, noise levels, fuel types,

and distances are the factors that must be considered when

negotiating with an installation professional.

Owner Orientation

NOT

for

REPRODUCTION

9

The actual physical location of your home generator has a

direct affect on:

1. The amount of plumbing required to fuel

your generator.

2. The amount of wiring required to control and connect

your generator.

Specific location guidelines are discussed in the installation

manual. Acquaint yourself with that information and confer

with your installer. Be sure to ask how your site might

affect installation costs and compliance with local codes

and standards.

 • Installgeneratoroutdoorsinanareathatwillnot

accumulate deadly exhaust gas.

 • DONOTinstallgeneratorwhereexhaustgascould

accumulate and enter inside or be drawn into a

potentially occupied building or structure.

 • BylawitisrequiredinmanystatestohaveaCarbon

Monoxide (CO) detector in operating condition in

your home. Carbon monoxide detector(s)

A

MUST

be installed and maintained indoors according to

the manufacturer’s instructions/ recommendations.

A CO monitor is an electronic device that detects

hazardous levels of CO. When there is a buildup of

CO, the monitor will alert the occupants by flashing

visual indicator light and alarm. Smoke alarms cannot

detect CO gas.

Generator Location

WARNING Exhaust heat/gases could ignite combustibles or

structures resulting in death or serious injury.

• Exhaust outlet side of weatherproof enclosure must have at least

5 ft (1.5 m) minimum clearance from any structure, shrubs, trees or

any kind of vegetation.

• Standby generator weatherproof enclosure must be at least

5 ft (1.5 m) from windows, doors, any wall opening, shrubs or

vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have a minimum

of 5 feet (1.5 m) overhead clearance from any structure, overhang

or trees.

• DO NOT place weatherproof enclosure under a deck or other type

of structure that may confine airflow.

• USE ONLY flexible steel fuel line provided. Connect provided fuel

line to generator, DO NOT use with or substitute any other flexible

fuel line.

• Smoke detector(s) MUST be installed and maintained indoors

according to the manufacturer’s instructions/ recommendations.

Carbon monoxide alarms cannot detect smoke.

• DO NOT place weatherproof enclosure in manner other than shown

in illustrations.

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventilation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be drawn

into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Smoke alarms cannot detect carbon

monoxide gas.

 • Ensureexhaustgasiskeptawayfromanywindows,

doors, ventilation intakes, soffit vents, crawl spaces,

open garage doors or other openings that can

allow exhaust gas to enter inside or be drawn into

a potentially occupied building or structure. Your

neighbor(s) home may be exposed to the engine

exhaust from your standby generator and must be

considered when installing your standby generator.

 • Windandaircurrentsshouldbetakeninto

consideration when positioning generator.

See the installation manual for full details on safe generator

location.

A

NOT

for

REPRODUCTION

10

Carefully inspect the home generator for any damage that

may have occurred during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight bill

and affix his signature under the consignor’s memo of loss or

damage. If loss or damage is noted after delivery, separate

the damaged materials and contact the carrier and your

installer for claim procedures. Parts damaged in shipping are

not warranted.

The home generator system is supplied with:

 • Oil(5W30Synthetic)

 • Flexiblesteelfuelline

 • Installationandstart-upmanual

 • Operator’smanual

 • Spareaccessroofkeys

 • Spare15AmpATO-typefuse

 • Remotewirelessmonitor

 • Antenna

Not included:

 • Carbonmonoxidedetector(s)

 • Smokedetector(s)

 • Startingbattery

 • Connectingwireandconduit

 • Fuelsupplyvalves/plumbing

 • Crane,liftingstraps,chainsorcables

 • Two60”lengthsof3/4”nominalminimumscheduled

40 steel pipe (NOT conduit)

 • Torquescrewdriver,5to50inch-poundrange

 • Voltage/frequencymeter

 • Two(2)AAbatteriesforremotewirelessmonitor

Delivery Inspection

NOT

for

REPRODUCTION

11

Read this operator’s manual and Important Safety Instructions before operating your generator.

Compare the illustration with your generator to familiarize yourself with the locations of various

controls and adjustments. Save this manual for future reference.

8kW Generator

Controls

B

A

C

D

E

F

G

H

J

Generator is shown with roof and access covers removed

for clarity.

- Lifting Holes —Providedateachcornerfor

lifting generator.

- Exhaust Port—High-performancemufflerlowersengine

noise to comply with most residential codes.

- Alternator—Anelectricalmachinethatgeneratesan

alternating current.

- Spark Plug—Adeviceinthecylinderheadoftheengine

that ignites the fuel mixture by means of an electric spark.

- Air Cleaner—Usesadrytypefilterelementandfoam

precleaner to protect engine by filtering dust and debris out

of intake air.

- Control Panel —Usedforvarioustest,operationand

maintenance functions. See System Control Panel.

- Circuit Breaker—Protectsthesystemfromshortsand

other over-current conditions.

- Battery—(installersupplied)—12VoltDC,sealedbattery

provides power to start the engine.

- Fuel Inlet Port—Attachappropriatefuelsupplyto

generator here.

A

B

C

D

E

F

G

H

J

NOT

for

REPRODUCTION

12

10 kW Generator

B

C

D

E

F

G

H

J

Generator is shown with roof and access covers removed

for clarity.

- Lifting Holes —Providedateachcornerfor

lifting generator.

- Exhaust Port—High-performancemufflerlowersengine

noise to comply with most residential codes.

- Alternator—Anelectricalmachinethatgeneratesan

alternating current.

- Muffler—Adevicetoreduceenginenoise.

- Air Cleaner—Usesadrytypefilterelementandfoam

precleaner to protect engine by filtering dust and debris out

of intake air.

- Control Panel —Usedforvarioustest,operationand

maintenance functions. See System Control Panel.

- Circuit Breaker—Protectsthesystemfromshortsand

other over-current conditions.

- Battery—(installersupplied)—12VoltDC,sealedbattery

provides power to start the engine.

- Fuel Inlet Port—Attachappropriatefuelsupplyto

generator here.

A

B

C

D

E

F

G

H

J

A

NOT

for

REPRODUCTION

13

Access Panels

A

The generator is equipped with an enclosure that has several

access panels, as shown.

Front Panel that is used to access:

•BatteryCompartment

•EngineOilDrainHose

•EngineOilFilter

•EngineValveCover

•SparkPlugs

Each generator is shipped with a set of identical keys.

A

NOT

for

REPRODUCTION

14

B

A

B B

C

To remove roof:

1. Remove the five screws that secure the roof to

the unit.

2. Carefully lift and remove roof from unit.

To remove front panel:

1. Remove the two screws that secure the panel to the

unit.

2. Lift and flex panel outward and off base. Use caution

not to damage the battery box (C.

To secure front panel:

1. Place panel in unit.

2. Secure the panel with two screws.

C

NOT

for

REPRODUCTION

15

ok

menu

esc

auto

off manual

System Control Panel

The generator control board, located inside the generator,

under the roof, is shown below. Brief descriptions of the

controls used during installation are:

A

- Menu/Programming Navigation Buttons —See

Menu section for details

B

- Mini USB Port—AuthorizedDealerServiceUseOnly.

C

- Generator Operation Control Buttons —

• “AUTO” Normal operating position. Press and hold

button to put unit into Automatic mode. In Automatic

mode, if a utility power outage is sensed, the system

will start the generator. When utility power is restored,

auto lets the engine stabilize internal temperatures,

shutsothegenerator,andwaitsforthenextutility

outage.

• “OFF” Turnsorunninggenerator,preventsunitfrom

starting, and resets any detected service codes.

OFF must be pressed and held for more than 5 seconds in

order to reset service code memory.

 •“MANUAL” Used to manually start the generator.

D

– 15 Amp Fuse—ProtectsthehomegeneratorDC

control circuits. If the fuse has ‘blown’ (melted open)

or was removed, the engine cannot crank or start.

Replace the fuse using only an identical ATO 15A fuse.

One spare fuse is supplied with the unit.

E

- Cover—Thisprotectivecovermustberemovedto

access the fuse and the USB port.

F

- Digital Display—Displaysgeneratormode,menu

options, service codes, and service engine indicators

More information may be found in Controls in the

operator’s manual.

A

B

C

D

F

E

NOT

for

REPRODUCTION

16

Menu

MENU

ENTER THE MENU (VIEW SETTINGS)

PRESS TO CONFIRM SELECTION WHEN PROGRAMMING.

ESCAPE (EXIT)

RETURN TO LAST MENU ITEM

RIGHT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

LEFT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

MANUAL MODE

USED TO MANUALLY START THE GENERATOR. PRESS AND HOLD BUTTON TO START

THE GENERATOR.

OFF

TURNS OFF RUNNING GENERATOR, PREVENTS UNIT FROM STARTING, AND RESETS

ANY DETECTED SERVICE CODES.

AUTOMATIC MODE

NORMAL OPERATING POSITION. PRESS AND HOLD BUTTON TO PUT UNIT INTO

AUTOMATIC MODE. IF A UTILITY POWER OUTAGE IS SENSED, THE

SYSTEM WILL START THE GENERATOR. WHEN UTILITY POWER IS RESTORED, AUTO

LETS THE ENGINE STABILIZE INTERNAL TEMPERATURES, SHUTS OFF THE GENERA-

TOR, AND WAITS FOR THE NEXT UTILITY POWER OUTAGE.

ok

GENERAL

SET-UP

PRESS AND HOLD [ARROW LEFT AND ARROW RIGHT] FOR

THREE SECONDS TO ENTER THE PROGRAM MODE.

WIRELESS

LINK MODE

PRESS AND HOLD [MENU AND ESC] FOR THREE SECONDS TO

ENTER THE WIRELESS LINKING MODE. (ONLY APPLICABLE ON

CERTAIN MODELS).

The following chart shows the icons for the buttons that control the system control panel.

The following chart describes key sequences for accessing different programming modes;

ok

NOT

for

REPRODUCTION

17

NOTE: Date and Time were set at the factory and stored in the control panel memory. The Exercise Cycle was

also set at the factory. The default exercise cycle occurs on Tuesdays, at 2:00 P.M. Central Standard Time.

To updated or change these settings, follow the steps below.

IF DURING PROGRAMMING NO BUTTONS ARE PRESSED FOR 30 SECONDS,

THE CONTROL PANEL WILL AUTOMATICALLY EXIT THE PROGRAM MODE.

SET DATE

ok

MONTH

FLASHING

ok

ok ok

or or

or

DAY##

FLASHING

YEAR

FLASHING

SET TIME

ok

HOURS

FLASHING

ok

ok ok

or or

MIN

FLASHING

SET EXERCISE

CYCLE

ok

or

AM/PM

FLASHING

HOURS

FLASHING

ok

or

ok

or

MIN

FLASHING

ok

DAY OF WEEK

FLASHING

or

AM/PM

FLASHING

ok

or

EVENT

LOG

ok

Display will scroll last service code event, date, time, and

temperature of when the event occured.

ok

or

OFF

If set to OFF, display will read: EXERCISE CYCLE OFF

ok

or

General Set Up Screen

For general set up, press and hold the left arrow and right arrow for 3 seconds. Follow the prompts as outlined below.

ok

NOT

for

REPRODUCTION

18

AUTOMATIC MODE

RUN TIME

DATE

or

TIME

EXERCISE CYCLE

GENERATOR ON

(When Generator Running - Auto Mode)

GENERATOR READY or SERVICE CODE DESCRIPTION

(When Generator NOT Running - Auto Mode)

(MENU)

ok

Control Panel Prompts

Automatic Mode

In Automatic Mode, the display screen will display via

scrolling text:

 • GENERATORREADY-iftheunitisinstandbyandutility

power is present.

 • GENERATORON-iftheunitisrunningandutility

power is not on.

 • SERVICECODE-ifasystemservicecodehasbeen

detected.

AUTOMATIC MODE

RUN TIME

DATE

or

TIME

EXERCISE CYCLE

GENERATOR ON

(When Generator Running - Auto Mode)

GENERATOR READY or SERVICE CODE DESCRIPTION

(When Generator NOT Running - Auto Mode)

(MENU)

ok

General System Parameters

To view general system parameters, press the MENU button.

The following will scroll across the digital display and then

move to the next item:

 • Runtime(totalhourstheunithasrunsinceinstallation)

 • Date

 • Time

 • ExerciseCycledateandstarttime

The user can press the LEFT ARROW or RIGHT ARROW at any

time to move to the next item.

The user can press ESCAPE to go back to GENERATOR READY.

If no user inputs are made for 10 seconds after all the items

have been displayed, the control board will reset to

GENERATOR READY.

NOT

for

REPRODUCTION

19

Operation

Battery

The installer must supply a rechargeable 12 volt DC starting

battery. See Battery in Final Installation Considerations in the

installation manual.

With the battery installed, all wiring to transfer switch and

home generator completed, utility power supplied to the

automatic transfer switch, and the unit in AUTO mode, the

battery receives a trickle charge while the engine is not

running. The trickle charge cannot be used to recharge a

battery that is completely discharged.

NOTICE A battery booster should never be used to quick

charge a low battery.

Engine Oil

The engine is shipped from the factory pre-run and filled

with synthetic oil (API SJ/CF 5W-30). This allows for system

operation in a wide range of temperature and climate

conditions. Before starting the engine, check oil level as

described in Maintenance.

Important Owner’s Considerations

NOTICE Any attempt to crank or start the engine before it has

been properly serviced with the recommended oil will result in

equipment failure.

• Damage to equipment resulting from failure to follow this

instruction will void engine and generator warranty.

WARNING Battery posts, terminals and related accessories

contain lead and lead compounds, chemicals known to the State

of California to cause cancer and reproductive harm. Wash hands

after handling.

15 Amp Fuse

The generator’s 15 Amp fuse is critical to correct system

operation. The 15 Amp fuse was removed at the factory.

Your installer will ensure the fuse is properly installed upon

completion of the installation.

NOT

for

REPRODUCTION

20

The generator is equipped with an exercise timer. During the

exercise period, the unit runs for approximately 20 minutes

and then shuts down. Electrical load transfer DOES NOT

occur during the exercise cycle (unless an utility power

outage occurs).

The generator will only enter the exercise cycle if the unit

is in the AUTO mode and this exact procedure is followed.

To set the exercise timer:

NOTICE The generator is set with a deservice code exercise

cycle setting of Tuesday at 2:00 P.M, Central Time. To change

the cycle setting, proceed to the following steps:

1. Choose the day and time you want your generator to

exercise.

2. Press and hold the left arrow and right arrow

simultaneously for three seconds to enter the General

Set-Up program mode. See General Set-Up flow chart

in Menu Section.

3. Verify and/or set the time and date on the unit.

4. Go to the SET EXERCISE prompt and hit the “OK”

button.

NOTICE Items will flash until they are selected.

Setting Exercise Timer

SELECT DAY: Use the left or right arrow to toggle

through the days of the week, Once the day is

selected, hit the “OK” button.

SELECT HOUR: Use the left or right arrow to toggle

through between 1 and 12. Choose the hour of day

you want the generator to exercise then hit the “OK”

button.

SELECT MINUTE: Use the left of right arrow to toggle

between :00 and :59. Choose the minute of the day

you want the generator to exercise then hit the “OK”

button.

SELECT AM/PM: Use the left of right arrow to toggle

between AM and PM. Once chosen, hit the “OK”

button.

NOTICE During the weekly exercise cycle, the generator will

run for 20 minutes, but it will not supply power to the home.

During the exercise cycle, the in-home monitor will continue

blinking the GENERATOR READY green LED.

If you want to change the day and time the unit exercises,

simply perform the procedure again.

To turn off the generator exercise cycle, go to the OFF

selection within the day of the week menu and press OK. The

display will then scroll: EXERCISE CYCLE OFF.

Automatic Operation

The generator’s control board constantly monitors utility

voltage. Should utility voltage drop below a preset level, the

control board will signal the engine to crank and start.

When utility voltage is restored above a preset voltage level,

the engine is signaled to shut down.

The actual system operation is not adjustable and is

sequenced by sensors and timers on the control board,

as follows:

Utility Voltage Dropout Sensor

 • Thissensormonitorsutilitysourcevoltage.

 • Ifutilitysourcevoltagedropsbelowabout70percent

of the nominal supply voltage, the sensor energizes

a 3 second timer. The timer is used to ‘sense’

brown-outs.

 • Oncethetimerhasexpired,theenginewillcrank

and start.

Utility Voltage Pickup Sensor

This sensor monitors utility voltage. When utility voltage is

restored above 80 percent of the nominal source voltage,

a time delay starts timing and the engine will go to engine

cool-down.

Engine Cool-down Timer

When utility power is sensed and the load transfers back to

the utility source, the engine will go into a cool down period

as described below:

 • IfthegeneratorhasrunforMOREthan5minutes,

once the utility transfer occurs, the engine will

continue to run for about 1 minute before shutting

down.

 • IfthegeneratorhasrunforLESSthan5minutes,once

the utility transfer occurs, the engine will continue to

run until 5 minutes has elapsed before shutting down.

NOT

for

REPRODUCTION

La page charge ...

GE 40374 Manuel utilisateur

Ce manuel convient également à

GE 40374 Manuel utilisateur

dans d''autres langues