Shindaiwa 493 Manuel utilisateur

SHINDAIWA OWNER'S/OPERATOR'S

MANUAL

CHAIN SAW

English

(Original instructions)

Français

Deutsch

Italiano

Español

WARNING

Read the instructions carefully and follow the rules for safe

operation.

Failure to do so could result in serious injury.

2

Introduction

This chain saw is designed for cutting wood or wood products.

Do not cut solid metal, sheet metal, plastic or any non-wood materials.

National or local regulation can restrict the use of this chain saw.

It is important for you to understand all safety precautions correctly before using your chain saw.

Misuse of the chain saw can cause serious bodily injury.

Never let children operate the saw.

This manual shows rules of safe operation, proper use, servicing, and maintenance of your shindaiwa chain saw.

Follow these instructions in order to maintain a good operating condition and a long service life.

For future reference, you should keep this operator's manual.

If this operator's manual has become illegible through impairment or is lost, please purchase a new one from your shindaiwa deal-

er.

When renting or lending this machine to a person who will operate it, always include this operator's manual, which provides expla-

nation and instructions.

When transferring a product, please deliver it attaching the operator's manual.

Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are

subject to change without notice.

Illustrations may include optional equipment and accessories, and may not include all standard equipment.

The unit is delivered with guide bar and saw chain separated.

Install guide bar and chain.

If there is any clause in this manual that is hard to be understood, please contact your shindaiwa dealer.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a re-

placement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are

also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not

amount to a major failure.

For warranty service, find the nearest Authorised Service Dealer in our dealer locator map at www.echo-australia.com.au/

en au/finder, or by calling 1300 274 447, or by emailing or writing to salesenquires@briggsandstratton.com.au, Briggs &

Stratton Australia Pty Ltd, Locked bag 5004, St Clair, NSW 2759.

3

Contents

Decals and symbols............................................................................................................ 4

Rules for safe operation...................................................................................................... 5

1. General precautions .................................................................................................. 5

2. Kickback safety precautions ...................................................................................... 8

3. Other safety precautions............................................................................................ 9

Description........................................................................................................................ 11

Assembly .......................................................................................................................... 12

Mounting guide bar and chain ..................................................................................... 12

Operation .......................................................................................................................... 14

Fuel and lubricant ........................................................................................................ 14

Chain lubricant............................................................................................................. 14

Cap indication.............................................................................................................. 14

Starting the cold engine............................................................................................... 15

Starting the warm engine............................................................................................. 16

Running ....................................................................................................................... 16

Stopping the engine..................................................................................................... 17

Checking chain tension................................................................................................ 17

Chain lubrication test ................................................................................................... 17

Pre cutting test............................................................................................................. 17

Correct use of chain brake................................................................................................ 18

Chain brake ................................................................................................................. 18

Checking the brake function of the brake .................................................................... 19

Release the chain brake.............................................................................................. 19

Non-manual chain brake.............................................................................................. 19

Cutting instruction .............................................................................................................20

General........................................................................................................................20

Felling a tree................................................................................................................ 21

Limbing ........................................................................................................................ 22

Bucking........................................................................................................................ 22

Tension and compression in timber............................................................................. 23

Service maintenance guide .............................................................................................. 24

Troubleshooting ................................................................................................................ 25

Saw chain maintenance.................................................................................................... 26

Service.............................................................................................................................. 28

Air filter ........................................................................................................................ 28

Check fuel system ....................................................................................................... 28

Fuel filter......................................................................................................................28

Oil filter ........................................................................................................................ 28

Spark plug ................................................................................................................... 28

Guide bar..................................................................................................................... 29

Sprocket / Clutch drum ................................................................................................ 29

Carburettor .................................................................................................................. 29

Automatic oiler............................................................................................................. 29

Cylinder fins (Cooling system)..................................................................................... 30

Silencer........................................................................................................................30

Replacement guide bar and chain............................................................................... 30

Storage ............................................................................................................................. 31

Long term storage (Over 30 days)............................................................................... 31

Disposal procedure........................................................................................................... 32

Specifications.................................................................................................................... 33

Declaration of conformity .................................................................................................. 34

UK Declaration of Conformity ........................................................................................... 35

4

Decals and symbols

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will

lead to serious personal injury or

death of operators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions

to an act or a condition which can

lead to serious personal injury or

death of operators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

Circle and slash symbol

means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provide tips

for use, care and maintenance of the

unit.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form / shape Symbol description / application Symbol form / shape Symbol description / application

Carefully read the operator's manual Chain oil fill

Wear eyes, ears and head protection Chain oiler adjustment

Warning!

Kickback may occur!

Purge bulb (Primer)

Emergency stop Carburettor adjustment

- Idle speed

Chain brake operation Guaranteed sound power level

Oil and petrol mixture

Locate this safety decal on your unit.

The complete unit illustration found in the "Description" sec-

tion will help you locate them.

Make sure the decal is legible and that you understand and

follow the instructions on it.

If a decal cannot be read, a new one can be ordered from

your shindaiwa dealer.

5

Rules for safe operation

1. General precautions

Operator's manual

Read the operator's manual for your chain saw carefully.

Be thoroughly familiar with the chain saw's controls and how to use the chain saw properly.

Failure to follow instructions could lead to personal injury.

If you have any questions or problems, please contact your shindaiwa dealer.

Physical condition

Do not operate a chain saw when you are fatigued or under the influence of alcohol or

drugs.

You should be in good physical and mental health in order to handle your chain saw safely.

Errors in judgement or execution can be serious or fatal.

If you have any physical condition which strenuous work could worsen, check with your phy-

sician before using a chain saw.

Do not operate when ill or fatigued, or under the influence of any substance or medication

which could affect your vision, dexterity or judgement.

The ignition system of this product generates electromagnetic fields during operation.

Magnetic fields can cause pacemaker interference or pacemaker failure.

To reduce health risks, we recommend that pacemaker users consult their physician and

the pacemaker manufacturer before operating this product.

Personal equipment

Always wear approved goggles to protect your eyes.

Wood chips, dust, snapping branches and other debris can be thrown by the cutting chain

into the operator's facial area.

Goggles may also offer limited protection in the event of the cutting chain hitting the oper-

ator in the eye area.

If conditions warrant that a ventilated face shield be worn, goggles must be worn under-

neath it.

shindaiwa advises wearing hearing protection at all times.

If not followed, hearing loss can occur.

You should reduce the risk of hearing damage by wearing either "headset" type protectors

or ear plugs which are approved by an authorized organization.

All persons who make part of their living using chain saws should be tested periodically

for hearing deterioration.

Always wear a helmet when working with a chain saw.

A safety hard helmet is highly recommended when felling or working under trees, or when

objects can fall on you.

Wear heavy duty, non-slip gloves for improved grip, and also for protection against cold

and vibration.

Safety tip shoes or boots with non-slip sole should be worn.

Never wear loose clothing, unbuttoned jackets, flared sleeves and cuffs, scarves, tie-

strings, neckties, cords, chains, jewellery, etc. which could snag the saw chain or under-

brush.

Clothing should be of sturdy, protective material.

It should be snug-fitting to resist snagging, but roomy enough for freedom of movement.

Trouser legs should not be flared or cuffed, and should be either tucked into the boot tops

or trimmed short.

Safety vests, leg chaps and logger's pants of ballistic material are available.

It is the operator's responsibility to wear such additional protection if conditions warrant it.

Never operate a chain saw when you are alone.

Arrange to have someone remain within calling distance in case you need help.

CAUTION

Stuffing ears with cotton is not recommended.

6

Fuel

1. Oil tank cap

2. Fuel tank cap

A: Tightening direction

Use an appropriate type of fuel container.

Bring an extinguisher or shovel in case of fire.

Despite the precautions which can be taken, operating a chain saw, or just working in the

forest, presents dangers.

Do not smoke or bring flame or sparks near to fuel supplies.

The fuel tank may be under pressure.

Always loosen the fuel cap and wait for pressure to be equalized before removing the cap.

Fill the fuel tank outdoors over bare ground and install the fuel cap securely.

Do not pour fuel indoors.

Wipe any spilled fuel off the unit.

Never refuel while the engine is still hot, or fuel a running engine.

Do not store the unit with fuel in its tank, because a fuel leak could start a fire.

Always fill up the chain oil first, then fill up the fuel mixture.

DANGER

Petrol and fuel are extremely flammable.

If spilled or ignited by ignition source, it can cause fire and serious injury or prop-

erty damage.

Extreme caution is required when handling petrol or fuel.

After refuelling, tighten fuel cap firmly and check for leakage.

In case of fuel leakage, repair before starting operation since there is a danger of

fire.

7

Starting engine

Move the chain saw at least 3 m from the fuelling point before starting the engine.

Do not allow other persons to be near the chain saw when you are starting or cutting with

the chain saw.

Keep bystanders and animals out of the work area.

Do not let anyone hold wood for you to cut.

Do not start cutting until you have a clear work area, secure footing and a planned retreat

path from the falling tree.

Before you start the engine, make sure that the saw chain is not contacting anything.

Keep the handles dry, clean, and free of oil or fuel mixture.

Operate the chain saw only in well-ventilated areas.

Exhaust gas, oil mist (from chain saw lubrication) or saw dust is harmful to health.

Transportation

1. Guide bar cover

When transporting your chain saw, use the appropriate guide bar cover.

Carry the chain saw with the engine stopped, the guide bar and saw chain to the rear, and

the silencer away from your body.

Transport and storage

Always keep the engine shut off and make it certain that cutting device is securely cov-

ered. When transporting the machine, activate the chain brake and secure it properly to

prevent flipping over, fuel spills and damage to the unit.

8

2. Kickback safety precautions

1. High kickback

In some cases, tip contact may cause a lightning-fast reverse reaction, kicking the guide

bar up and back toward the operator (this is called a rotational kickback).

Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back

toward the operator (this is called a linear kickback).

Either or these reactions may cause you to lose control of the saw and come in contact

with the moving chain, which could result in serious personal injury.

As a chain saw user, you should take several steps to keep your cutting jobs free from ac-

cident or injury.

With a basic understanding of kickback, you can reduce or eliminate the element of sur-

prise.

Sudden surprise contributes to accidents.

Understand that rotational kickback is preventable by keeping an unshielded bar nose from

touching an object or the ground.

Do not operate a chain saw with one hand!

Serious injury to the operator, helpers or bystanders may result from one-handed operation.

For proper control, always use two hands when operating a chain saw, one of which oper-

ates the trigger.

Otherwise, this can result in the chain saw "skating" or skidding, which can result in person-

al injury due to loss of control.

Be alert for the phenomena "skating" and "bouncing", greater risk from kickback.

Be cautious not to lose balance of your body due to "drop" at the end of a cut.

Keep a good firm grip on the saw which both hands, with the right hand on the rear han-

dle and the left hand on the front handle, when the engine is running.

Use a firm grip with thumbs and fingers encircling the chain saw handles.

A firm grip will help you reduce kickback and maintain control of the saw.

Two hands must be used to control the saw at all times.

Do not overreach or cut above chest height.

Make sure that the area in which you are cutting is free from obstructions.

Do not let the bar nose contact a log, branch, or any other obstruction which could be hit

while you are operating the saw.

Cutting at high engine speeds may reduce the likelihood of kickback.

But cutting at part-throttle or low engine speeds may be preferable to control the chain saw

in tight situations and may also reduce the likelihood of kickback.

Follow manufacturer's sharpening and maintenance instructions for the saw chain.

Use only replacement guide bars and chains specified by the manufacturer, or the ac-

ceptable equivalents of these guide bars and chains.

DANGER

Kickback safety precaution for chain saw users: kickback may occur when the nose

or tip of the guide bar touches an object or when the wood closes in and pinches the

saw chain in the cut.

9

3. Other safety precautions

Vibration and cold

It is believed that a condition called Raynaud's Phenomenon, which affects the fingers of cer-

tain individuals, may be brought about by exposure to cold and vibration.

Accordingly, your shindaiwa chain saw has an anti-vibration device designed to reduce the

intensity of vibration received through the handles.

Exposure to cold and vibration may cause tingling and burning followed by loss of colour and

numbness in the fingers. (White finger syndrome)

We strongly recommend you take the following precautions because the minimum exposure

which might trigger the ailment is unknown.

Keep your body warm, especially the head and neck, feet and ankles, and hands and

wrists.

Maintain good blood circulation by performing vigorous arm exercises during frequent

work breaks and also by not smoking.

Limit the number of hours of chain saw operation.

Try to fill a part of each work day with jobs other than chain sawing.

If you experience discomfort, redness and swelling of the fingers, followed by whitening

and loss of feeling, consult your physician before further exposing yourself to cold and

vibration.

Repetitive stress injuries

It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoul-

ders may cause soreness, swelling, numbness, weakness and extreme pain to the areas just

mentioned.

To reduce the risk of repetitive stress injury, do the following:

Avoid using your wrist in a bent, extended or twisted position.

Instead, try to maintain a straight wrist position.

Also, when grasping, use your whole hand, not just the thumb and index finger.

Take periodic breaks to minimize repetition and rest your hands.

Reduce the speed and force in which you do the repetitive movement.

Do exercises to strengthen the hand and arm muscles.

See a doctor if you feel tingling, numbness or pain in the fingers, hands, wrists or arms.

Relative to EU directive "Vibration"

EU Directive "Vibration" (2002/44/EC) was designed to protect people from safety and health

risks arising from mechanical vibration of a machine by enforcing employers to limit a stand-

ardized 8 hour daily vibration exposure level, A(8).

Any person or organization that employs a person to operate a machine has to take the A(8)

value into account when letting the person use it.

Mechanical vibration values (equivalent vibration value) of this machine, which shall be used

as a guide to simplify the calculation of A(8) value, are as follows:

MODEL Type

Front / Left handle (m/s

2

)2.4

Rear / Right handle (m/s

2

)2.3

10

Machine conditions

Do not operate a chain saw that is damaged, improperly adjusted, or not completely and

securely assembled.

Do not operate the chain saw with a loose or defective silencer.

Be sure that the saw chain stops moving when the throttle control trigger is released.

If your saw is subjected to high loads due to a fall or impact, always perform inspection

and operation check in order to confirm if there is anything wrong before continuing work.

Cutting

Do not operate a chain saw in a tree unless you have been specifically trained to do so.

Keep all parts of your body away from the saw chain when the engine is running.

Use extreme caution when cutting small-size brush and saplings because slender ma-

terial may catch the saw chain and be whipped toward you or pull you off balance.

Stay on the uphill side when bucking or limbing logs which might roll when cut.

When cutting a limb that is under tension, be alert for spring-back so that you will not be

struck by the limb or chain saw when the tension in the wood fibres is released.

Cutting while on a ladder is extremely dangerous because the ladder can slip and your

control of the chain saw is limited.

Working aloft should be left to professionals.

Keep both feet on the ground.

Do not work from off-the-ground positions.

Stop the engine before setting the chain saw down.

Wood practices

Operating a chain saw safely requires a chain saw in proper working order, sound judge-

ment, and knowledge of the methods which should be applied in each cutting situation.

Do not let any person use your saw unless he has read this operator's manual and fully

understands its instructions.

Use your saw only to cut wood or wood products.

Do not cut solid metal, sheet metal, plastics or any non-wood materials.

Services

All chain saw service operations, other than items listed in the operator's manual main-

tenance instructions, should be performed by competent service personnel.

(For example, if an improper tool is used to hold the flywheel in order to remove the clutch,

structural damage to the flywheel could occur and subsequently could cause the flywheel

to burst.)

WARNING

Do not modify a chain saw in any way.

Only attachments and parts supplied by shindaiwa or expressly approved by

shindaiwa for use with the specific shindaiwa chain saw models are authorized.

Although certain unauthorized attachments are useable with the shindaiwa power-

head, their use may, in fact, be extremely dangerous.

CAUTION

Do not touch hot surfaces of cylinder cover and silencer after you used the chain saw.

11

Description

1. Silencer - The silencer controls the exhaust noise and

prevents hot, glowing particles of carbon from leaving the

silencer.

2. Front hand guard - Guard between the front handle and

the saw chain for protecting the hand from injuries and

aiding in control of the chain saw if the hand slips off the

handle.

This guard is used to activate the chain brake which is to

stop the saw chain rotation.

3. Rear handle (for the right hand) - Support handle locat-

ed towards the rear of the engine housing.

4. Rear hand guard - Extension on the lower part of the

rear handle for protecting the hand from the chain if it

breaks or degrooves.

5. Clutch cover - Protective cover to the guide bar, saw

chain, clutch and sprocket when the chain saw is in use.

6. Chain tension adjuster - Device to adjust chain tension.

7. Chain catcher - A projection designed to reduce the risk

of the operator's right hand from being hit by a chain

which has broken or derailed from the guide bar during

cutting.

8. Spiked bumper - Device, fitted in front of the guide bar

mounting point, acting as a pivot when in contact with a

tree or log.

9. Guide bar - The part that supports and guides the saw

chain.

10. Chain - Chain, serving as a cutting tool.

11. Type and serial number

12. Oil tank cap - For closing the oil tank.

13. Starter handle - The grip of the starter, for starting the

engine.

14. Fuel tank cap - For closing the fuel tank.

15. Momentary stop switch - Button for momentarily short-

ing ignition voltage, causing the engine to stop. This is

NOT an ON/OFF Ignition switch.

16. Throttle trigger - Device activated by the operator's fin-

ger, for controlling the engine speed.

17. Throttle trigger lockout - A safety lever which must be

depressed before the throttle trigger can be activated in

order to prevent the accidental operation of the throttle

trigger.

18. Purge bulb (primer pump) - When starting engine, push

primer pump 3 or 4 times.

19. Choke control knob - Device for enriching the fuel / air

mixture in the carburettor to aid cold starting.

20. Cleaner cover latch - Device for installing the air cleaner

cover.

21. Air cleaner cover - Covers air filter.

22. Front handle (for the left hand) - Support handle locat-

ed at the front of the engine housing.

23. Cylinder cover - The cooling air flow grill. It cover the

cylinder, spark plug and silencer.

24. Safety decal - Part number X505-011830

25. Operator's manual - Included with unit.

Read before operation and keep for future reference to

learn proper, safe operating techniques.

26. Tool - 13 x 19 mm T-wrench (combination screwdriver /

spark plug socket).

27. Guide bar cover - Device for covering the guide bar and

saw chain during transport and other times when the

chain saw is not in use.

12

Assembly

Mounting guide bar and chain

1. Release chain brake

2. Two nuts

3. Clutch cover

Install guide bar and chain as follows.

Loosen two nuts and remove clutch cover.

Mount the bar and slide toward clutch to make saw chain installation easier.

4. Guide bar

5. Clutch

6. Bar hole

7. Tension adjuster

8. Brake connector

9. Direction to tension the chain

10. Front hand guard (Brake lever)

Install saw chain as shown.

(Ensure cutters are pointing in the right direction)

Release the chain brake, and install the clutch cover over the guide bar studs.

Tighten two nuts finger tight.

Ensure that chain tension adjuster fits into bar hole.

Align the brake connector of the clutch cover to the groove on the side of the front hand

guard.

WARNING

For your own safety, always stop the engine before performing any of the following

operations.

CAUTION

1. All adjustments should be made cold.

2. Always wear gloves when working on chain.

3. Do not operate with a loose chain.

NOTE

Move the chain brake lever (Front hand guard, Brake connector) fully rearward to remove or

install the clutch cover to the chain saw.

13

Hold the bar nose up and turn the adjuster clockwise until the chain fits snugly against

the underside of the bar.

A: Proper tension

B: Improper tension

Tighten both nuts with the bar nose held up.

Pull the chain around the bar by hand.

Loosen the adjustment if you feel tight spots.

14

Operation

Fuel and lubricant

Fuel is a mixture of regular grade petrol and an air-cooled 2-stroke engine oil.

Minimum 89 Octane unleaded petrol is recommended.

Do not use fuel containing methyl alcohol or more than 10 % of ethyl alcohol.

Recommended mixture ratio; 50 : 1 (2%) for ISO-L-EGD Standard (ISO 13738), JASO

FC, FD grade and shindaiwa recommended oil.

- Never use two-stroke oil intended for water-cooled engines, motor-cycle engines.

- Do not mix directly in engine fuel tank.

- Avoid spilling petrol or oil.

Spilled fuel should always be wiped up.

- Handle petrol with care, it is highly inflammable.

- Always store fuel in approved container.

Chain lubricant

Proper lubrication of the chain while in operation minimizes friction between the chain,

the guide bar and sprocket and also clutch components such as needle bearing and

clutch assembly.

Use shindaiwa genuine chain oil or shindaiwa recommended chain oil specially formulat-

ed for bars and chains for proper lubrication.

These oils contain tackifiers, anti-aging and anti-oxidizing agents.

Consult your shindaiwa dealer for the proper chain oil.

Never use waste or reclaimed oil to avoid various malfunctions on oil system, clutch sys-

tem, chain and guide bar.

Lubrication problems caused by the use of improper oil will void the warranty.

Especially, vegetable based chain oil quickly turns to resin and adheres to oil pump,

chain, guide bar, clutch needle bearing and clutch assembly.

It causes malfunctions and shorten product life.

Flush chain oil system with mineral or chemical based chain oil after use, if it is required to

use vegetable oil due to local / municipal rule or any other reason.

For a short time emergency operation, fresh SAE 10W-30 motor oil can be used.

Cap indication

Fuel and oil tanks are indicated by the following illustrations.

Fuel tank cap

(Red)

Chain oil tank cap

(Black)

CAUTION

Whenever opening up the fuel tank, always loosen the cap very slowly and wait for

the tank pressure to be equalized before removing the cap.

15

Starting the cold engine

A: Starter handle

1. Chain brake ACTIVATED position

2. Choke control knob (Close)

3. Purge bulb (Primer pump)

4. Choke control knob (Open)

Fill the fuel tank with fuel mixture.

It is not permitted to fill fuel above the shoulder level of fuel tank.

Fill the chain oil tank with lubricant.

Press hand guard forward.

(Chain brake ACTIVATED position)

Pull choke control knob all the way out.

Push primer pump until fuel is visible in primer pump.

Securely hold the chain saw.

Make sure guide bar and saw chain are not touching anything when starting the saw.

Pull starter handle several times until first firing sound is heard.

Push choke control knob all the way in.

Pull starter handle again.

WARNING

After choke control knob is pulled and then knob is returned to original position,

throttle remains a little open (latch condition).

If engine is started in this latch condition, chain starts to turn.

Do not start engine before chain brake is activated.

CAUTION

1. After starting the engine, immediately squeeze and release throttle trigger for

disengaging throttle latch and returning engine to idle, and pull front hand guard

towards the operator immediately. (Chain brake RELEASED position)

2. Do not increase engine speed while chain brake is engaged.

3. Use the chain brake only in starting the engine or in emergencies.

4. Never use throttle latch for cutting.

Use it only when starting the engine.

NOTE

Do not pull starter rope out to the maximum position.

Do not allow starter handle to snap back against the casing.

16

Starting the warm engine

1. Chain brake ACTIVATED position

Confirm there is fuel and chain oil in the tanks.

Press hand guard forward.

(Chain brake ACTIVATED position)

Securely hold the chain saw.

Pull starter handle.

Choke may be used if necessary, but after first firing sound pull throttle trigger a little to

release throttle latch and choke.

After choke control knob is pulled and then knob is returned to original position, throttle re-

mains a little open (latch condition).

Running

1. Chain brake RELEASED position

2. Throttle trigger lockout

3. Throttle trigger

After engine starts, allow it to idle for a few minutes.

Pull front hand guard towards the operator immediately.

(Chain brake RELEASED position)

Squeeze throttle trigger gradually to increase engine revolution.

The chain starts moving when the engine reaches 3800 r/min approximately.

Ensure proper acceleration and lubrication of saw chain and guide bar.

Do not run the engine at high speed unnecessarily.

Be sure that saw chain stops moving when throttle trigger is released.

17

Stopping the engine

1. Throttle trigger

2. Momentary stop switch

Release throttle trigger and allow engine to idle.

Push the momentary stop switch until the engine is stopped.

Checking chain tension

Chain tension should be checked frequently during work and corrected if necessary.

Tension the chain as tight as possible, but so it can still be pulled easily along the bar by

hand.

Chain lubrication test

Hold the chain just above a dry surface and open the throttle to half speed for 30 sec-

onds.

A thin line of "thrown" oil should be seen on the dry surface.

Pre cutting test

Familiarize yourself with your chain saw before you start actual cutting.

For this purpose it may be wise to practice by cutting some small logs or limbs several

times.

Do not allow either people or animals into the work area.

Multiple operators - Keep a safe distance between two or more operators when working to-

gether simultaneously.

NOTE

If engine does not stop, pull choke control knob all the way out to stop engine.

Return the unit to your authorized shindaiwa dealer to check and repair momentary stop

switch before starting the engine again.

WARNING

Make sure that the engine is shut off when checking chain tension.

NOTE

Always loosen clutch cover nuts before turning the chain tension adjuster, otherwise the

clutch cover and tensioner will be damaged.

18

Correct use of chain brake

Chain brake

The chain brake's function is to stop chain rotation after a kickback.

It neither prevents nor reduces kickback.

Do not depend on the chain brake for protection against kickback.

Even with a chain brake, depend on your own good sense and proper cutting methods just as

though there were no chain brake.

Even with normal use and proper maintenance, the response time of the brake may lengthen.

The following may interfere with the brake's ability to protect the operator:

Saw wrongly held too close to operator's body.

Kickback time may be too fast even for a perfectly maintained brake to work in time.

The operator's hand may not be in position to contact the hand guard.

Brake will not be tripped.

Lack of proper maintenance lengthens the brake's stopping time, making it less effective.

Dirt, grease, oil, pitch, etc. getting into the working parts of the mechanism may lengthen

the stopping time.

Wear and fatigue of the activating brake spring, and wear of the brake / clutch drum and

pivot points may lengthen the brake's stopping time.

A damaged hand guard and lever may render the brake inoperative.

DANGER

Kickback motion is very hazardous.

If the tip of the bar touches wood or the like, the guide bar kicks back in an instant.

The chain brake reduces the possibility of injury due to kickback.

Always check that chain brake works properly before use.

NOTE

For practice, while cutting a small tree, push the front guard forward to engage the

brake.

At all times, confirm whether the brake works properly before each task.

If the chain brake is clogged with wood chips, function of the brake deteriorates a little.

Always keep the device clean.

Do not increase engine revolutions while the chain brake is engaged.

Chain brake is used in emergencies.

Do not use it unless absolutely necessary.

When using throttle latch at starting, keep the chain brake in position.

And after starting the engine, release the brake immediately.

Never test the brake in an area where petrol fumes are present.

19

Checking the brake function of the brake

1. Place the chain saw on the ground.

2. Hold the handle with both hands and accelerate the engine to high speed by using the

throttle trigger.

3. Operate the chain brake by turning your left wrist against the front hand guard whilst grip-

ping the front handle.

4. The chain stop immediately.

5. Release the throttle trigger.

If the chain does not stop immediately, take the saw to your shindaiwa dealer to repair.

Release the chain brake

When front hand guard is fully pulled towards the operator, chain brake is released.

Non-manual chain brake

1). End of the guide bar may be placed at the height about 50 cm.

2). Rear handle should be gripped lightly with the right hand.

The non-manual chain brake stops the operation of the saw chain in such a manner that the

kickback action produced at the end of the guide bar non-manually actuates the chain brake.

To make sure that the non-manual chain brake operates properly, proceed as follows:

1. Stop the engine of the chain saw.

2. Operate the front and rear handles with hands (grip them lightly), so that the guide bar

may be placed at the height of about 50 cm as shown in Fig.

3. Softly detach the left hand from the front handle, and touch the end of the guide bar

against the wood or the like placed below so that the machine receives an impact.

(* at this time the rear handle should be gripped lightly with right hand)

4. The impact is transferred to the brake lever, which actuates the chain brake.

IMPORTANT

When checking the operation of the non-manual chain brake, use a soft surface substance

like wood to provide the impact so the saw chain is not damaged.

20

Cutting instruction

General

In all circumstances the operation of the chain saw is a one-man job.

It is difficult at times to take care of your own safety, so don't assume the responsibility for a

helper as well.

After you have learned the basic techniques of using the saw, your best aid will be your own

good common sense.

The accepted way to hold the saw is to stand to the left of the saw with your left hand on the

front handle so you can operate the throttle trigger with your right index finger.

Before attempting to fell a tree, cut some small logs or limbs.

Be thoroughly familiar with the controls and the responses of the saw.

Start the engine, see that is running properly.

Squeeze the trigger to open the throttle wide open, then start the cut.

It is not necessary to press down hard to make the saw cut.

If the chain is properly sharpened, the cutting should be relatively effortless.

Pushing the saw too hard will slow the engine and cutting will actually be more difficult.

Some material may adversely affect the housing of your chain saw.

(Example: palm tree acid, fertilizer etc.)

To avoid housing deterioration carefully remove all packed saw dust around clutch and guide

bar area and wash with water.

DANGER

Do not let the nose or tip of the guide bar touch anything while engine is running to

avoid kickback.

La page charge ...

Shindaiwa 493 Manuel utilisateur

Shindaiwa 493 Manuel utilisateur

dans d''autres langues