IKEA IX5HHEXVS00 User Instructions

Marque: IKEA

Modèle: IX5HHEXVS00

Catégorie: Frigos

Taper: User Instructions

Ce manuel convient également à

IX5HHEXWS02

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.ikea.com for additional information. If you still need assistance, call us at 1-800-253-1301. In

Canada, visit our website at _vw.ikea.com or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

TableofContents / [ndice/Tabledes mati6res

REFRIGERATOR SAFETY ............................... 1

INSTALLATION INSTRUCTIONS ................... 2

REFRIGERATOR USE ..................................... 8

REFRIGERATOR CARE ................................. 10

TROUBLESHOOTING .................................... 11

WARRANTY .................................................... 13

SEGURIDAD DEL REFRIGERADOR ............ 14

INSTRUCCIONES DE INSTALACION .......... 15

USO DE SU REFRIGERADOR ...................... 21

CUlDADO DE SU REFRIGERADOR ............. 23

SOLUCION DE PROBLEMAS ....................... 24

GARANT[A ...................................................... 26

SI_CURITI_ DU RI_FRIGI_RATEUR ................ 27

INSTRUCTIONS D'INSTALLATION .............. 28

UTILISATION DU REFRIGERATEUR ........... 34

ENTRETIEN DU RI_FRIGI_RATEUR ............. 36

DEPANNAGE .................................................. 37

GARANTIE ...................................................... 39

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

W10215626

iMPORTANT SAFETY iNSTRUCTiONS

WARNING:To reduce the risk of fire, electric shock, or injuryto persons when using the refrigerator, follow basic precautions,

including the following:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

[] Use nonflammable cleaner.

[] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator.

[] Disconnect power before installing ice maker (on ice maker

kit ready models only).

SAVETHESEINSTRUCTIONS

Proper DisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoffthe doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Remove the Packaging

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/2"

(1.25 cm) space at the top and behind the refrigerator. If your

refrigerator has an ice maker, allow extra space at the back for the

water line connections. When installing your refrigerator next to a

fixed wall, leave 21/2'' (6.3 cm) minimum on the hinge side (some

models require more) to allow for the door to swing open.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the

refrigerator in a location where the temperature will fall below 55°F

(13°C).

21/2" (6.3 era)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension

cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the refrigerator to OFR Depending on

your model, turn the freezer control to the word OFF, or press the

Freezer down arrow touch pad until a dash (-) appears in both the

Freezer and Refrigerator displays as shown. Disconnect the

refrigerator from the electrical source. When you are finished,

reconnect the refrigerator to the electrical source and reset the

temperature controls to the desired setting. See "Using the

Controls."

qm atyCor,trol

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • ¼" Nut driver

• 7Ae"and 1/2"Open-end or two • ¼" Drill bit

adjustable wrenches

• Cordless drill

IM PORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3Ae"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

• For models with water filters, the disposable water filter

should be replaced at least every 6 months.

Water Pressure

A cold water supply with water pressure of between 35 and

120 psi (241 and 827 kPa)is required to operate the water

dispenser and ice maker. Ifyou have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT: Ifyou turn the refrigerator on before the water line is

connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a 1/2"to 11/4'' (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

IM PORTANT:

• Make sure it is a cold water pipe.

Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the rear of the refrigerator to the water

pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm)

O.D. (outside diameter) copper tubing. Be sure both ends of

copper tubing are cut square.

5. Using a cordless drill, drill a V4"hole in the cold water pipe you

have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E.Compression sleeve

F. Shutoff valve

G.Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"drilled hole in

the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so the washer makes a watertight seal. Do not

overtighten.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten or

you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

A. Copper tubing D. Compression sleeve

B. "P" clamp E. Water valve inlet port

C. Compression nut

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with

the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

A. Plastic water line

B. Water valve inlet port

C. Compression nut

D. Copper tubing

E. "P" clamp

6. Check connection by pulling on copper tubing. Attach copper

tubing to refrigerator cabinet with a "P" clamp. Turn on water

supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill the ice container.

1"OO1_5NEEDED: _e", %", ¼" hex-head socket wrench, a

#2 Phillips screwdriver, and a flat-blade screwdriver.

IM PORTANT:

• All graphics referenced in the following instructions are

included later in this section after "Final Steps."

• If you only want to remove and replace the doors, see

"Remove Door(s) and Hinges" and "Replace Door(s) and

Hinges."

• Before you begin, turn the refrigerator control OFF, and

remove food and adjustable door or utility bins from the doors.

A. Plastic water tubing C. Compression nut

B. Sleeve D. Copper tubing

Remove and Replace Refrigerator Door Handles

Using a 3/32"Allen wrench, loosen the two setscrews located

on the side of each handle. Pull the handle straight out from

the door. Make sure you keep the screws for reattaching the

handles. See Metal Handle graphic 1.

• To replace the handles, reverse the directions.

Remove Doors and Hinges

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Starting with the right-hand side door, remove the parts for the

top hinge as shown in Top Hinge graphic. Lift the refrigerator

door from the bottom hinge pin.

4. Remove the hinge pin cover from the bottom hinge pin and

keep it for later use. See Bottom Hinge graphic.

5. Before removing the left-hand side door, disconnect the wiring

plug located on top of the top hinge by wedging a flat-blade

screwdriver or your fingernail between the two sections. See

Wiring Plug graphic.

NOTE: The green, ground wire remains attached to the hinge.

Remove the parts for the left-hand side door top hinge as

shown in the Top Hinge graphic. Lift the door from the bottom

hinge pin.

NOTE: Remove the hinge pin cover from the bottom hinge pin

and keep it for later use. See Bottom Hinge graphic.

Replace Doors and Hinges

Assemble the parts for the top hinges as shown in Top Hinge

graphic. Do not tighten the screws completely.

Replace the parts for the bottom hinges as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator doors.

NOTE: Provide additional support for the refrigerator doors

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the doors in place while you are

working.

3. Align each door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

5. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IM PORTANT:

• Two people may be required to remove and replace the freezer

drawer.

• All graphics are included later in this section after "Final

Steps."

Remove and Replace Drawer Handle

• Using a 3_32"Allen wrench, loosen the two setscrews located

on the side of each handle. Pull the handle straight out from

the drawer. Make sure you keep the screws for reattaching the

handle. See Metal Handle graphic 2.

• To replace the handle, reverse the directions.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to insert the two screws

in the bottom of the drawer front into the brackets. See

Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are in

place. Reinstall top hinge cover as shown in Top Hinge

graphic.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug into a grounded 3 prong outlet.

3. Return all removable door parts to door and food to

refrigerator.

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Top Hinges

A. Hinge Cover Screw

B, Top Hinge Cover

C, 5/18"Hex Head Hinge Screws

D. Top Hinge

Bottom Hinges

A. Hinge Pin Cover

B, Bottom Hinge

C. Hinge Screws

Wiring Plug

\\\

Metal Handle

A, 3/32" Setscrew

iii!iiiiii!iiii,'_iiii!ii!iiilliliiiiiiiiiiiiiiii_ii!

Metal Handle

A, 3/32"Setscrew

A, Loosen 4 Drawer Bracket Screws

Adtsf the

Your refrigerator has two adjustable rollers located at the base of

the refrigerator. If your refrigerator seems unsteady or you want

the door to close more easily, use the instructions below.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

Using a 3/8"hex driver, turn the roller adjustment screw on

each side to raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the adjustment screws and

rollers. This makes it easier to turn the screws. It may take

several turns of the roller adjustment screw to adjust the tilt of

the refrigerator.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left.

Turn the brake foot clockwise until it is firmly against the floor

to keep the refrigerator from rolling forward when the freezer

drawer is pulled open.

A. Front roller adjustment screw

B. Brake foot

Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

REFRIGERATORUSE

(F_'e_cl_ doo modes

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

The temperature controls are located at the top front of the

refrigerator compartments.

Temperature Controls

For your convenience, the temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the recommended setting as shown.

Recommended Setting "4"

Or* _ - --_ off

IM PORTANI"."

The recommended setting should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

To Turn Off/On:

Press the freezer down arrow touch pad until a dash (-) appears in

both the refrigerator and freezer displays. Neither compartment

will cool.

Humidity Control (on some models)

The humidity control turns on a heater to help reduce moisture on

the door hinge seal. Use in humid environments or when you

notice moisture on the door hinge seal. The refrigerator uses more

energy when Humidity Control is on.

• Press the control to ON when the environment is warm and

more humid, or if you notice moisture on the door hinge seal.

• Press the control to OFF to save energy when the environment

is less humid.

HumidityControl

On Off

Adjusting Controls

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart below as

a guide.

For controls press the up or down arrow touch pads. Except when

starting the refrigerator, do not adjust either control more than one

setting at a time. Wait 24 hours between adjustments for the

temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

one setting higher

FREEZER too warm/too little ice FREEZER Control one

setting higher

REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

FREEZER too cold FREEZER Control one

setting lower

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT / LOW (open) for best storage of fruits and vegetables with

skins.

VEGETABLES / HIGH (closed) for best storage of fresh, leafy

vegetables.

/_ _

ce s4s.,@

(on soyse "_'_ode s}

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Ice Production Rate

The ice maker should produce a complete batch of ice

approximately every 3 hours.

To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

• Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT:

Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

NOTE: When cleaning stainless steel, always wipe with the

grain to avoid cross-grain scratching.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size, shape,

and wattage (no greater than 40 watts).

1. Unplug the refrigerator or disconnect power.

2. Remove the light shield, if necessary.

• Top of the refrigerator compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

• Top of freezer compartment - The light shield opens from

the back. Firmly press forward on the notches in the back

of the shield and pull the shield down.

NOTE: You may need to remove the upper freezer shelf or

basket to access the light assembly.

Replace the burned-out bulb(s) with an appliance bulb(s) no

greater than 40 watts.

Replace the light shield.

• Top of the refrigerator compartment - Insert the tabs on

the shield into the liner holes on each side of light

assembly. Slide the shield toward the front until it locks

into place.

NOTE: To avoid damaging the light shield, do not force

the shield beyond the locking point.

Top of the freezer compartment - Insert the front tabs of

the shield into the liner and snap the back portion of the

shield over the light assembly.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Power cord unplugged? Plug into a grounded 3 prong outlet.

Is outlet working? Plug in a lamp to see ifthe outlet is

working.

Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Control(s)."

New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are

listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker

Pulsating - fans/compressor adjusting to optimize

performance

Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

Sizzling/Gurgling - water dripping on the heater during

defrost cycle

Popping - contraction/expansion of inside walls, especially

during initial cool-down

Water running - may be heard when ice melts during the

defrost cycle and water runs into the drain pan

Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back inthe correct

position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

_ _ _,_ _ 7,,¸ _,, _ _

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Control(s)."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

Freezer door closed completely? Firmly close the freezer

compartment door. If the freezer compartment door will not

close all the way, see "The doors will not close completely,"

earlier in this section.

Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice volume improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice quality improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

Odor transfer from food? Use airtight, moisture proof

packaging to store food.

Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

Water filter installed on the refrigerator? Gray or dark

discoloration in ice indicates that the water filtration system

needs additional flushing. Flush the water system before using

a new water filter. Replace water filter when indicated. See

"Water Filtration System."

WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY

LIM ITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts

and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be

provided by a Whirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies

only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain

service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Any food or medicine loss due to refrigerator or freezer product failures.

7. Pickup and delivery. This major appliance is intended to be repaired in your home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool's published installation instructions.

11. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or

cannot be easily determined.

12. Discoloration, rust, or oxidation of stainless steel surfaces.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies. 6/o8

For additional product information, visit www.ikea.com.

If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may

contact Whirlpool at the number below.

Have your complete model number ready. You can find your model number and serial number on the label, located on the inside wall of

the refrigerator compartment.

For assistance or service in the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

If you need further assistance, you can write to Whirlpool with any questions or concerns at the address below:

In the U.S.A.: In Canada:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Whirlpool Brand Home Appliances

Customer eXperience Centre

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please keep this User Instructions and model number information for future reference.

LEAGRADECEMOSlacompradeesteproductodealtacalidad.Siustedexperimentaunproblemaquenosehayacubiertoen

SOLUClONDEPROBLEMAS,visitenuestrositiodeinternetenwww.ikea.comparaobtenerinformaci6nadicional.Siconsidera

queaQnnecesitaayuda,Ilamenosal1-800-253-1301.EnCanadA,visitenuestrositiodeintemetenwww.ikea.comoIlamenosal

1-800-807-6777.

NecesitaratenetamanosunQmerodemodeloydeserieubicadosenlaparedinteriordelcompartimientodelrefrigerador.

SEGURIDAD DELREFRIGERADOR

Su seguridad y la seguridad de los demos es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre

todos los mensajes de seguridad.

Este es el simbolo de advertencia de seguridad.

Este simbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a

usted y a los demas.

Todos los mensajes de seguridad iran a continuaci6n del simbolo de advertencia de seguridad y de la palabra

"PELIGRO" o "ADVERTENCIA". Estas palabras significan:

9 O

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesibn grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesibn grave.

Todos los mensajes de seguridad le diran el peligro potencial, le diran c6mo reducir las posibilidades de sufrir una lesi6n y Io que

puede suceder si no se siguen las instrucciones.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENC_A: Para reducir el riesgo de incendio, choque electrico, o lesiones personales al usar su refrigerador siga

estas precauciones basicas, incluidas las siguientes:

[] Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

[] No quite la terminal de conexi6n a tierra.

[] No use un adaptador.

[] No use un cable electrico de extensi6n.

[] Desconecte el suministro de energia antes de darle servicio.

[] Vuelva a colocar todos los componentes y paneles antes de

hacerlo funcionar.

[] Remueva las puertas de su refrigerador viejo.

[] Use un limpiador no inflamable.

[] Mantenga los materiales y vapores inflamables, tales como

gasolina, alejados del refrigerador.

[] Use dos o mas personas para mover e instalar el

refrigerador.

[] Desconecte el suministro de energia antes de instalar la

fabrica de hielo (en aquellos modelos que incluyen el juego

de instalaci6n de la fabrica de hielo).

CONSERVAR ESTAS INSTRUCCIONES

C6mo deshacerse adecuadamente de

su refrigeradorviejo

Peligro de Asfi×ia

Remueva las puertas de su refrigerador viejo.

No seguir esta instrucci6n puede ocasionar la muerte

o da_o al cerebro.

Antes de tirar su viejo refrigerador o congelador:

• Saque las puertas.

• Deje los estantes en su lugar, asi los ni_os no pueden meterse

adentro con facilidad.

IMPORTANTE: El atrapamiento y asfixia de ni_os no es un

problema del pasado. Los refrigeradores tirados y abandonados

son un peligro, aun si van a quedar ahi "por unos pocos dias". Si

Ud. esta por deshacerse de su refrigerador viejo, por favor siga

las instrucciones que se dan a continuacion para prevenir

accidentes.

INSTRUCCIONESDE INSTALACION

Peligro de Peso Excesivo

Use dos o m_s personas para mover e instaiar

el refrigerador.

No seguir esta instrucci6n puede ocasionar una

lesi6n en la espalda u otto tipo de lesiones.

Cbmo quitar los materiales de empaque

• Quite los restos de cinta y goma de las superficies de su

refrigerador antes de encenderlo. Frote un poco de

detergente liquido para vajillas sobre el adhesivo con los

dedos. Limpie con agua tibia y seque.

No use instrumentos filosos, alcohol para fricciones, liquidos

inflamables o productos de limpieza abrasivos para eliminar

los restos de cinta o goma. Estos productos pueden da_ar la

superficie de su refrigerador. Para m_s informacion, vea

"Seguridad del refrigerador".

• Deshagase de todos los materiales de embalaje o reciclelos.

C6mo mover su refrigerador:

Su refrigerador es pesado. Cuando mueva el refrigerador

para limpiarlo o para darle servicio, cerci6rese de cubrir

el piso con cart6n o madera para evitar dados en el mismo.

AI mover el refrigerador, siempre tire directamente hacia

afuera. No menee el refrigerador de lado a lado ni Io haga

"caminar" cuando Io trate de mover ya que podria dadar

el piso.

Limpieza antes del uso

Una vez que usted haya quitado todos los materiales de

empaque, limpie el interior de su refrigerador antes de usarlo. Vea

las instrucciones de limpieza en "Cuidado de su refrigerador".

Informaci6n importante para saber acerca de los estantes

y tapas de vidrio:

No limpie los estantes y tapas de vidrio con agua caliente

mientras estAn frios. Los estantes y tapas pueden romperse

si se exponen a cambios bruscos de temperatura o impacto,

como seria un golpe brusco. El vidrio templado se ha

diseSado para hacerse aSicos. Esto es normal. Los estantes

y tapas de vidrio son muy pesados. Use ambas manos al

sacarlos para evitar que se caigan.

s tos ........

Peligro de Explosi6n

Mantenga los materiales y vapores inflamables,

tales como gasolina, aiejados del refrigerador.

No seguir esta instrucci6n puede ocasionar la muerte,

explosi6n, o incendio.

Para asegurar la ventilacion apropiada de su refrigerador, permita

un espacio de 1/2"(1,25 cm) en la parte superior y detras del

refrigerador. Si su refrigerador tiene fabrica de hielo, asegQrese de

que haya espacio adicional atras para las conexiones de la linea

de agua. Cuando instale su refrigerador junto a una pared fija,

deje 21/2'' (6,3 cm) minimo del lado de la bisagra (algunos modelos

requieren mas), para permitir que la puerta se abra

completamente.

NOTA: No se recomienda instalar el refrigerador cerca de un

horno, radiador u otra fuente de calor. No instale el refrigerador en

un lugar donde la temperatura sea menor de 55°F (13°C).

1/2"(1,25cm)

Peligro de Choque EI6ctrico

Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

No quite la terminal de conexi6n a tierra.

No use un adaptador.

No use un cable el_ctrico de extensi6n.

No seguir estas instrucciones puede ocasionar

la muerte, incendio o choque el6ctrico.

Antes de mover el refrigerador a su ubicacion final, es importante

asegurarse que tiene la conexion electrica adecuada.

M_todo de conexi6n a tierra recomendado

Se requiere una fuente de energia electrica de 115 Voltios, 60 Hz.,

CA solamente y con fusibles de 15 6 20 amperios, conectada a

tierra. Se recomienda que use un circuito separado solo para su

refrigerador. Use un tomacorriente que no se pueda apagar con

un interruptor. No use un cable electrico de extension.

NOTA: Antes de realizar cualquier tipo de instalacion, limpieza o

de quitar un foco de luz, ponga el refrigerador en OFF (Apagado).

Dependiendo del modelo, gire el control del congelador hacia la

palabra OFF o presione el boton con la flecha hacia abajo del

congelador hasta que aparezca un guion (-) en la pantalla del

congelador y la del refrigerador, como se muestra. Desconecte el

refrigerador de la fuente de suministro electrico. Cuando haya

terminado, reconecte el refrigerador a la fuente de energia

electrica y vuelva a poner los controles de temperatura en la

posicion deseada. Vea "Uso de los controles".

aumidityCo_t,ol

Reina las herramientas y piezas necesarias antes de comenzar la

instalaci6n. Lea y siga las instrucciones provistas con cualquiera

de las herramientas enlistadas aqui.

HERRAMIENTAS NEOESARIAS:

• Destornillador de hoja plana • Llave de tuercas de V4"

• Llaves de boca de 7Ae"y W' 0 • Broca de _A"

dos Ilaves ajustables • Taladro inalambrico

IM PORTANTE:

• Todas las instalaciones deben hacerse de acuerdo a los

requisitos locales de plomeria.

• No use una valvula perforadora o una valvula de montura de

3/_e"(4,76 mm), la cual reduce el flujo de agua y se obstruye

con mas facilidad.

Use tuberia de cobre y revise si hay fugas. Instale la tuberia de

cobre solo en Areas donde la temperatura vaya a permanecer

por encima del punto de congelacion.

Para modelos con filtros de agua, el filtro de agua desechable

debera reemplazarse por Io menos cada 6 meses.

Presi6n del agua

Se necesita un suministro de agua fria con presion de agua entre

35 y 120 Ibs/pulg 2(241 y 827 kPa) para hacer funcionar el

despachador de agua y la fabrica de hielo. Si tiene preguntas

acerca de la presion del agua, Ilame a un plomero competente

autorizado.

Suministro de agua por 6smosis inversa

IMPORTANTE: La presion del suministro de agua que sale de un

sistema de osmosis inversa y va a la valvula de entrada de agua

del refrigerador necesitarA ser entre 35 y 120 Ibs/pulg 2(241 y

827 kPa).

Si se conecta un sistema de filtracion de agua de osmosis inversa

al suministro de agua fria, la presion de agua al sistema de

osmosis inversa necesitarA ser de un minimo de 40 a 60 Ibs/pulg 2

(276 a 414 kPa).

Si la presion de agua hacia el sistema de osmosis inversa es

menor de 40 a 60 Ibs/pulg 2(276 a 414 kPa):

• Verifique si el filtro de sedimentos en el sistema de osmosis

inversa esta bloqueado. Reemplacelo si fuera necesario.

• Deje que se vuelva a Ilenar el tanque de almacenaje del

sistema de osmosis inversa despu_s del uso intenso.

Si su refrigerador tiene un filtro de agua, se podra reducir la

presion aOn mas si se usa en conjunto con un sistema de

osmosis inversa. Saque el filtro de agua. Vea "Sistema de

filtracion de agua".

Si tiene preguntas acerca de la presion del agua, Ilame a un

plomero competente autorizado.

C,onecEe,, e mnst s ,se.......eguG

Lea todas las instrucciones antes de comenzar.

IMPORTANTE" Si enciende el refrigerador antes de conectar la Oonexi6n al refrigerador

tuberia de agua, APAGUE la fabrica de hielo.

Dependiendo de su modelo, la linea de agua puede bajar de la

parte superior o subir de la parte inferior. Siga las instrucciones de

Conexi6n a la linea de agua conexion para su modelo.

1. Desenchufe el refrigerador o desconecte el suministro de

energia.

2. CIERRE el suministro principal de agua. ABRA la Ilave de agua

mas cercana el tiempo suficiente para que la tuberia de agua

se vacie.

Localice una tuberia de agua fria vertical de 1/2"a 1V4"

(12,7 mm a 31,8 mm) cerca del refrigerador.

IM PORTANTE:

• AsegOrese de que sea una tuberia de agua fria.

Una tuberia horizontal funcionara, pero debe seguirse el

procedimiento indicado a continuacion: taladre por el lado

de arriba de la tuberia, no por debajo. Esto ayudara a

mantener el agua alejada del taladro. Esto tambien evita

que se acumule el sedimento normal en la valvula.

Determine la Iongitud de la tuberia de cobre que necesite.

Mida desde la conexion de la parte trasera del refrigerador

hasta la tuberia de agua. Agregue 7 pies (2,1 m) para poder

mover el refrigerador para limpiarlo. Use tuberia de cobre de

1/4"(6,35 mm) de diametro externo. AsegQrese que ambos

extremos de la tuberia de cobre estan cortados a escuadra.

Usando un taladro inalambrico, taladre un orificio de 1/4"en la

tuberia de agua fria que ha seleccionado.

A. Tuberfa de agua frfa

B. Abrazadera para tuberfa

C. Tuberfa de cobre

D. Tuerca de compresi6n

E.Manga de

compresi6n

F. V41vula de cierre

G. Tuerca de presi6n

6. Afiance la valvula de cierre a latuberia de agua fria con la

abrazadera para tuberia. AsegQrese de que el extremo de

salida se encuentre sujeto firmemente en el orificio taladrado

de 1/4"en la tuberia de agua y que la arandela esta bajo la

abrazadera de la tuberia. Apriete la tuerca de presion. Apriete

los tornillos de la abrazadera para tuberia lentamente yen

forma pareja de manera que la arandela provea un cierre

hermetico. No apriete demasiado.

7. Deslice la manga de compresion y la tuerca de compresion

sobre la tuberia de cobre como se muestra. Inserte el extremo

de la tuberia en el extremo de salida en forma pareja hasta

donde sea posible. Atornille la tuerca de compresion en el

extremo de salida usando la Ilave de tuercas ajustable. No

apriete demasiado porque se puede quebrar la tuberia de

cobre.

Estilo 1

1. Quite la tapa de plastico del puerto de entrada de la valvula de

agua. Fije el tubo de cobre a la entrada de la valvula usando

una tuerca de compresion y manga de compresion como se

muestra. Ajuste la tuerca de compresion. No apriete

demasiado. Verifique que la tuberia de cobre este segura,

jalandola.

2. Haga un lazo de servicio con latuberia de cobre. Evite

torceduras al enrollar la tuberia de cobre. Asegure la tuberia

de cobre a la carcasa del refrigerador con una abrazadera

en "P".

A. Tuberfa de cobre

B.Abrazadera en "P"

C. Tuerca de compresi6n

D. Manga de compresi6n

E. Puerto de entrada de

la v4lvula de agua

3. Abra el suministro de agua al refrigerador y revise si hay fugas

de agua. Tape cualquier fuga que encuentre.

Estilo 2

1. Haga un lazo de servicio (diametro minimo de 2 pies [61 cm])

con la tuberia de cobre. Evite torceduras al enrollar la tuberia

de cobre.

2. Quite la tapa de plastico del puerto de entrada de la valvula de

agua. Coloque una manga y tuerca de compresion en la

tuberia de cobre.

Introduzca el extremo de la tuberia de cobre al puerto de

entrada de la valvula de agua. Moldee ligeramente la tuberia

de tal forma que la tuberia entre de forma recta al puerto para

evitar torceduras.

Coloque el extremo libre de la tuberia en un recipiente o

fregadero y ABRA el suministro principal de agua. Enjuague la

tuberia hasta que el agua salga limpia. CIERRE la valvula de

cierre de la tuberia de agua.

4. Deslice la tuerca de compresion sobre la manga y atornille en

el puerto de entrada de la valvula de agua.

A. Tuberfa de agua de pl4stico C. Tuerca de compresi6n

B. Manga D. Tuberfa de cobre

Con una Ilave de tuercas ajustable, sostenga la tuerca sobre

la linea de agua de plastico para evitar que se mueva. Luego,

con una segunda Ilave, gire la tuerca de compresion que esta

en la tuberia de cobre, en el sentido contrario de las

manecillas del reloj para apretar completamente. No apriete

demasiado.

A. Lfnea de agua de pl4stico

B. Puerto de entrada de la

v_lvula de agua

C. Tuerca de compresi6n

D. Tuberfa de cobre

E.Abrazadera en "P"

Verifique la conexion jalando la tuberia de cobre. Sujete la

tuberia de cobre a la carcasa del refrigerador con una

abrazadera en "P". Abra el suministro de agua al refrigerador y

revise si hay fugas de agua. Tape cualquier fuga que

encuentre.

Complete la instalaci6n

Peligro de Choque El_ctrico

Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

No quite la terminal de conexi6n a tierra.

No use un adaptador.

No use un cable el_ctrico de extensi6n.

No seguir estas instrucciones puede ocasionar

la muerte, incendio o choque el_ctrico.

NOTA: Deje transcurrir 24 horas para la produccion del primer

Iote de hielo. Deshagase de los tres primeros Iotes de hielo

producidos. Deje transcurrir 3 dias para que se vuelva a Ilenar de

hielo el recipiente.

HERRAMIENTAS NEOESARIAS: Llave de cubo de cabeza

hexagonal de %d', sA",y V4",destornillador Phillips N° 2 y un

destornillador de hoja plana.

IM PORTANTE:

• Todas las ilustraciones alas que se hace referencia en las

siguientes instrucciones se incluyen m_s adelante en esta

seccion despu6s de "Pasos finales".

Si usted solo quiere quitar las puertas y volverlas a colocar,

vea las secciones "Como quitar las puertas y las bisagras" y

"Como volver a poner las puertas y las bisagras en su lugar".

Antes de comenzar, gire el control del refrigerador a OFF

(Apagado), saque los alimentos y la puerta regulable o

recipientes de uso general de las puertas.

Cbmo quitar y volver a colocar las manijas

de la puerta del refrigerador

Con una Ilave Allen de 3_32", afloje los dos tornillos fijos

ubicados en el lado de cada manija. Jale la manija

directamente hacia afuera de la puerta. AsegOrese que guarda

los tornillos para reinstalar las manijas. Vea la ilustracion

Manija de metal 1.

• Para volver a colocar las manijas, invierta las instrucciones.

Cbmo quitar la puerta y las bisagras

Peligro de Choque EI6ctrico

Desconecte el suministro de energia antes de sacar

las puertas.

No seguir esta instrucci6n puede ocasionar la muerte

o choque el6ctrico.

Desenchufe el refrigerador o desconecte el suministro de

energia.

Mantenga las puertas del refrigerador cerradas hasta que este

listo para levantarlas y quitarlas de la carcasa.

NOTA: Mientras quita las bisagras siempre disponga de un

soporte adicional para la puerta del refrigerador. No se confie

en que los imanes de la junta de la puerta van a sostener la

puerta en su lugar mientras trabaja.

1. Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

3. Comenzando por la puerta del lado derecho, saque las piezas

de la bisagra superior, como se muestra en la ilustracion

Bisagra superior. Levante y saque la puerta del refrigerador

del pasador inferior de la bisagra.

4. Saque la cubierta del pasador de la bisagra inferior y guardela

para usarla mas tarde. Vea la ilustracion Bisagra inferior.

5. Antes de sacar la puerta del lado izquierdo, desconecte el

enchufe de cableado que esta ubicado sobre la bisagra

superior introduciendo un destornillador de hoja plana o la

u_a entre las dos secciones. Vea la ilustracion Enchufe de

cableado.

NOTA" El alambre verde a tierra permanece sujeto a la

bisagra.

Saque los componentes de la bisagra superior de la puerta

del lado izquierdo, como se muestra en la ilustracion Bisagra

superior. Levante y saque la puerta del pasador inferior de la

bisagra.

NOTA" Saque la cubierta del pasador de la bisagra inferior y

guardela para usarla m_s tarde. Vea la ilustracion Bisagra

inferior.

Cbmo volver a poner la puerta y las bisagras en su lugar

Ensamble los componentes de las bisagras superiores, como

se muestra en la ilustracion Bisagra superior. No atornille

completamente los tornillos.

Vuelva a colocar los componentes de las bisagras inferiores,

como se muestra en la ilustracion Bisagra inferior. Apriete los

tornillos. Vuelva a poner en su lugar las puertas del

refrigerador.

NOTA" Mientras quita las bisagras siempre disponga de un

soporte adicional para las puertas del refrigerador. No se

confie en que los imanes de la junta de las puertas van a

sostener las puertas en su lugar mientras trabaja.

3. Alinee cada puerta de modo que la base de la puerta del

refrigerador este alineada en forma pareja con la parte

superior del cajon del congelador. Apriete todos los tornillos.

4. Vuelva a conectar el enchufe de cableado en la parte superior

de la puerta del lado izquierdo del refrigerador.

5. Vuelva a colocar las cubiertas de la bisagra superior.

C6mo quitar y volver a colocar el caj6n del congelador

IM PORTANTE:

• Tal vez se necesiten dos personas para quitar y volver a

colocar el cajon del congelador.

• Todas las ilustraciones se incluyen en esta seccion, m_s

adelante, despu6s de "Pasos finales".

C6mo quitar y volver a colocar la manija del cajbn

• Con una Ilave Allen de 3_32", afloje los dos tornillos fijos

ubicados en el lado de cada manija. Jale la manija

directamente hacia afuera del cajon. AsegOrese de guardar

los tornillos para reinstalar la manija. Vea la ilustracion Manija

de metal 2.

• Para volver a colocar la manija, invierta las instrucciones.

Para quitar el frente del caj6n

1. Abra el cajon del congelador en toda su extension.

2. Afloje los cuatro tornillos que sujetan las guias del cajon al

frente del cajon. Vea la ilustracion Remocion del frente del

cajon.

NOTA" Afloje los tornillos girAndolos tres o cuatro veces.

Mantenga los tornillos en el frente del cajon.

3. Levante el frente del cajon hacia arriba y fuera de los tornillos.

Vea la ilustracion Como quitar el frente del cajon.

Para volver a colocar el frente del caj6n

1. Deslice las guias fuera del compartimiento del congelador.

Inserte los tornillos en la parte superior del frente del cajon,

dentro de las ranuras que estan en los soportes del cajon. Vea

la ilustracion Como volver a colocar el frente del cajon.

2. Jale los soportes del cajon hacia usted para colocar los dos

tornillos en la base del frente del cajon, dentro de los

soportes. Vea la ilustracion Como volver a colocar el frente del

cajon.

3. Apriete por completo los cuatro tornillos.

Pasos finales

Revise todos los orificios para cerciorarse que los tapones de

los orificios y los tornillos esten en su lugar. Vuelva a colocar la

cubierta de la bisagra superior, como se muestra en la

ilustracion Bisagra superior.

Peligro de Choque EI6ctrico

Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

No quite la terminal de conexi6n a tierra.

No use un adaptador.

No use un cable el_ctrico de extensi6n.

No seguir estas instrucciones puede ocasionar

la muerte, incendio o choque el6ctrico.

Conecte a un contacto de pared de conexion a tierra de 3

terminales.

Regrese todas las partes removibles a la puerta y la comida al

refrigerador.

Peligro de Choque El_ctrico

Desconecte el suministro de energia antes de sacar las puertas.

No seguir esta instrucci6n puede ocasionar la muerte o choque el_ctrico.

Bisagras superiores

A. Tomillo para la cubierta de

la bisagra

B, Cubierta de la bisagra superior

C. Tornillos de cabeza hexagonal

para bisagra de _6"

D. Bisagra superior

Bisagras inferiores

A. Cubierta del pasador de la bisagra

B, Bisagra inferior

C. Tomillos para bisagra

Enchufe de cableado

\\\

Manija met_lica

A, Tomillo de ajuste de 3/32"

Manija metalica

A, Tomillo de ajuste de 3/32"

A. Aflc ie los 4 tomillos de

soporte del cajon

La page charge ...

IKEA IX5HHEXVS00 User Instructions

Marque: IKEA

Modèle: IX5HHEXVS00

Catégorie: Frigos

Taper: User Instructions

Ce manuel convient également à

IX5HHEXWS02

Télécharger le PDF

rapport

dans d''autres langues

English: IKEA IX5HHEXVS00
español: IKEA IX5HHEXVS00

IKEA IX5HHEXVS00 User Instructions

Ce manuel convient également à

IKEA IX5HHEXVS00 User Instructions

dans d''autres langues

Autres documents