GE GDF530PGMBB Guide d'installation

Marque: GE

Modèle: GDF530PGMBB

Catégorie: Lave-vaisselle

Taper: Guide d'installation

31-4000251 Rev 0 03-21 GEA

IDENTIFY YOUR MODEL

Locate your full dishwasher model number on the tub wall just inside its door.

The model number is 12 digits containing letters and numbers. Identify the 10th digit in

your model number. For example: GDT535PSM 6 SS or GDF510PGM 5 SS.

If the 10th digit is a 6, follow the instructions on pages 1-32.

If the 10th digit is any other number, follow the instructions on pages 33-64.

Built-In DishwashersInstallation Instructions

IDENTIFIEZ VOTRE MODÈLE

Repérez le numéro de modèle complet de votre lave-vaisselle sur la paroi de la cuve

juste à l’intérieur de sa porte.

Le numéro de modèle consiste en 12 caractères de lettres et de chiffres. Identifiez

le 10e caractère de votre numéro de modèle. Par exemple : GDT535PSM 6 SS or

GDF510PGM 5 SS.

Si le 10e caractère est 6, suivez les instructions des pages 1 à 32.

Si le 10e caractère est n’importe quel autre chiffre, suivez les instructions des pages

33 à 64.

ARRÊT

Instructions

D’Installation

Lave-vaisselle

encastré

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS

shown throughout these instructions.

While performing installations described in this booklet,

gloves, safety glasses or goggles should be worn.

IMPORTANT – Observe all governing codes and ordinances.

• Note to Installer – Be sure to leave these instructions

for the consumer’s and local inspector’s use.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

• Skill Level – Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper installation is the responsibility of the

installer. Product failure due to improper installation

is not covered under the GE Appliances Warranty.

See warranty information.

• Completion Time – 1 to 3 Hours. New installations

require more time than replacement installations.

IMPORTANT – The dishwasher MUST be installed to

allow

for future removal from the enclosure if service is required.

Care should be exercised when the appliance is installed

or removed,

to reduce the likelihood of damage to the

power supply cord.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for

available custom panel kits.

Your dishwasher is a water heating appliance.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• Remove all power leading to the appliance from the

circuit breaker or fuse box before beginning installation.

Failure to do so can result in a risk of electrical shock.

•

To reduce the risk of electric shock, fire, or injury to persons,

the installer must ensure that the dishwasher is completely

enclosed at the time of installation.

• The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative

if you are in doubt that the appliance is properly

grounded. If house wiring is not 2-wire with ground, a

ground must be by the installer. When house wiring

is aluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

•

To reduce the risk of electric shock, fire, or injury to persons,

the installer should check to ensure that wires are not pinched

or damaged, the house wiring is attached to the junction box

bracket through a strain relief, and all electrical connections

made at the time of install (wire nuts) are contained inside of

the junction box cover.

WARNING

• Retire todos los conductores de corriente del

electrodoméstico de disyuntor o de la caja del fusible

antes de comenzar con la instalación. Si no cumple con

esto, se podrá producir el riesgo de descargas eléctricas.

• Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador debe asegurarse

de que el lavaplatos esté completamente cerrado en

el momento de la instalación.

• La conexión inadecuada del conductor de conexión a

tierra del equipamiento puede provocar un riesgo de

descarga eléctrica. Consulte a un electricista calificado

o representante de servicio técnico si tiene dudas

sobre la correcta conexión a tierra del aparato. Si el

cableado doméstico no cuenta con un cable de 2 hilos

con conexión a tierra, un instalador debe realizar una

conexión a tierra. Cuando el cableado doméstico es de

aluminio, asegúrese de usar un compuesto antioxidante

y conectores de aluminio a cobre aprobados por UL.

• Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador deberá realizar un

control para asegurar que los cables no estén pellizcados

ni dañados, que el cableado del hogar esté conectado a la

ficha de la caja de empalmes a través de un amortiguador

de refuerzo, y que todas las conexiones eléctricas

realizadas en el momento de la instalación (tuercas para

cables) estén dentro de la tapa de la caja de empalmes.

ADVERTENCIA

See your Owner’s Manual for details on how to contact us regarding installation questions

Built-In DishwashersInstallation Instructions

Opening the door will cause the

dishwasher to tip forward when it is

not fully installed. When opening the door prior to the

dishwasher being fully installed, hold the top of the

dishwasher securely with one hand and hold the door

with the other hand. Gloves should be worn.

CAUTION

Abrir la puerta hará que el

lavavajillas se incline hacia

adelante cuando no se encuentre completamente

instalado. Al abrir la puerta antes de haber instalado

completamente el lavavajillas, sostenga la parte superior

del lavavajillas de forma segura con una mano y sostenga

la puerta con la otra mano. Se deberán usar guantes.

PRECAUCIÓN

READ CAREFULLY

KEEP THESE INSTRUCTIONS

PARTS SUPPLIED IN

INSTALLATION PACKAGE:

• Junction box cover

• #10 hex-head screw

• Hose clamp

• Drain hose hanger

• 2 Plug buttons

• Toekick (pre-installed on some models)

• 2 Tub trim pieces (on some models)

• 2 Mounting brackets for wood countertops

or side cabinets

• 2 #8-18 x 5/8” Phillips special head screws,

to secure dishwasher to underside of

countertop or to side cabinets

• Insulation pieces (on some models)

• Literature, samples and/or coupons

TOOLS YOU WILL NEED:

• Phillips-head screwdriver

• 1/4” and 5/16” nutdriver

• 6” Adjustable wrench

• Level

• Carpenter’s square

• Measuring tape

• Safety glasses

• Flashlight

• Bucket to catch water when flushing the line

• 15/16” socket

• Gloves

• Pliers

For New Installations Only:

• Tubing cutter

• Drill and appropriate bits

• Hole saw set

MATERIALS YOU WILL NEED:

• ´*+7*DUGHQ+RVH7KUHDGÛHOERZLQFOXGLQJ

gasket) - with opposite end sized to fit Hot Water Line

• Thread seal tape

• UL-listed wire nuts (3)

• Masking tape

Materials For New Installations Only:

• Air gap for drain hose, if required

• Waste tee for house plumbing, if applicable

• Electrical cable or Power Cord Kit WX09X70910 (5’ 5” long)

or WX09X70911 (7’ 11” long) depending on installation.

• Strain relief for electrical connection

• Hose clamps

• Hand shut-off valve (recommended)

• Hot Water Line–3/8” minimum, copper tubing (including

ferrule, compression nut) or GE Appliances Part #

WX28X326, flexible braided hose.

• WD24X10065 drain hose (12’ long) or WD24X10062

drain hose (4’ long), if needed.

Installation Preparation

Hole Saw Set

Tubing Cutter

Drill and Bits

Phillips-Head

Screwdriver

15/16” Socket

1/4” and 5/16”

Nutdriver

Bucket

Flashlight

Gloves

Carpenter’s

Square

Safety Glasses

Level

Hose Clamp

Junction

Box Cover

#10

Hex-Head

Junction

Box Screw

3/8" long

Mounting

Brackets

#8 Phillips

Special

Head Screws

5/8" long

Literature

Insulation

(on some models)

Tub Trim Pieces

(on some models)

Pliers

Strain

Relief

Optional -

12' Drain Hose - WD24X10065

4’ Drain Hose - WD24X10062

Hot

Water

Line

Waste Tee

Electrical Cable

(or Power Cord,

if applicable)

Wire Nuts (3)

GHT 90°Elbow

Hand

Shut-Off

Valve

Air Gap

Plug

Buttons

Masking Tape

Toekick

Drain Hose Hanger

Thread

Seal Tape

(if applicable)

6” Adjustable

Wrench

Hose

Clamps

Measuring Tape

PREPARE DISHWASHER ENCLOSURE

• The rough cabinet opening must be at least 24” deep,

24” wide and approximately 34-1/2” high from floor to

underside of the countertop.

• The dishwasher must be installed so that drain hose is

no more than 16’ in length for proper drainage.

• The dishwasher must be fully enclosed on the top,

sides and back, and must not support any part of the

enclosure.

CLEARANCES: When installed into

a corner, allow 2” min. clearance

between dishwasher and adjacent

cabinet, wall or other appliances.

Allow 25-1/2” min. clearance from

the front of the dishwasher for

door opening.

34-1/2”+1/4”

Underside of

Countertop

to Floor

This Wall Area

Must be Free

of Pipes and

Wires

Cabinets

Square

and

Plumb

Plumbing and Electric Service

Must Enter Inside This Area

24”

Min.

4”

6”

24”

Min.

33-1/2” to 34-3/4”

Underside of

Countertop

to Floor

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 16’ distance to drain.

NOTE : Air gap must be used if waste tee or disposer

connection is less than 18” above floor to prevent siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions.

• Do local codes or ordinances require an air gap?

• Is waste tee less than 18” above floor?

If the answer to either question is YES, Method 1

MUST be used.

•

If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2” diameter hole in the cabinet wall within

the shaded areas shown in PREPARE DISHWASHER

ENCLOSURE section for the drain hose connection.

The hole should be smooth with no sharp edges.

IMPORTANT – When connecting

drain line to disposer, check to be sure

that drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF

PLUG IS LEFT IN PLACE.

Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes

and ordinances. The air gap must be installed according

to manufacturer’s instructions.

Tip: Avoid unnecessary service call charges.

Always be sure disposer drain plug has been removed

before attaching dishwasher drain hose to the disposer.

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

25-1/2"

Remove

Drain

Plug

Installation Preparation

To reduce the risk of electric shock, fire, or injury to

persons, the installer must ensure that the dishwasher

is completely enclosed at the time of installation.

WARNING

Method 2 – “High Drain Loop” with Waste Tee or Disposer

Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador debe asegurarse

de que el lavaplatos esté completamente cerrado en el

momento de la instalación.

ADVERTENCIA

DISHWASHER HANDLE DIMENSION: The dishwasher

door should be flush with the cabinet. For models with

a handle, the total depth (with handle) is 26-1/4” max.

depending on the model. Locate the Quick Specs document

online for more dishwasher dimensions.

72”

max.

72”

max.

Drain Hose Hanger

18”

min.

32” min. -

72” max.

Drain Hose Hanger

18”

min.

32” min. -

72” max.

Installation Preparation

Cabinet Preparation & Wire Routing

•

The wiring may enter the opening from either side, rear

or the floor within the shaded area illustrated above

in figure and defined in PREPARE DISHWASHER

ENCLOSURE section.

• Cut a 1-1/2" maximum diameter hole to admit the

electrical cable. Edges of hole should be smooth and

rounded. Permanent wiring connections may pass

through the same hole as the drain hose and hot water

line, if convenient. If cabinet wall is metal, the hole

edge must be covered with a bushing.

NOTE:

Power cords with plug must pass through a

separate hole in the cabinet.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For permanent connections the cable must be routed

as shown in figure. Cable must extend a minimum of

24" from the rear wall.

• For power cord connections, install a 3-prong

grounding type receptacle in the sink cabinet rear wall,

6" min. or 18" maximum from the opening, 6" to 18"

above the floor.

• Use only WX09X70910 (5’ 5” long) or WX09X70911 (7’

11” long) Dishwasher Power Cord Kit. Do not use an

extension cord or adapter plug with this appliance.

PREPARE ELECTRICAL WIRING

White

18"

24"

from Wall

from

Cabinet

Alternate Receptacle

Location in Adjacent

Cabinet

Ground

Black

1-1/2" Dia. Hole (Max.)

18"

Receptacle

Location

Area

Retire todos los conductores de

corriente del electrodoméstico

de disyuntor o de la caja del fusible antes de comenzar

con la instalación. Si no cumple con esto, se podrá

producir el riesgo de descargas eléctricas.

ADVERTENCIA

Remove all power leading to the

appliance from the circuit breaker or

fuse box before beginning installation. Failure to do so

can result in a risk of electrical shock.

WARNING

La conexión inadecuada del

conductor de conexión a

tierra del equipamiento puede provocar un riesgo de

descarga eléctrica. Consulte a un electricista calificado

o representante de servicio técnico si tiene dudas sobre

la correcta conexión a tierra del aparato. No modifique el

enchufe que se suministra con el aparato; si no calza en el

tomacorrientes, haga que un técnico calificado le instale

un tomacorrientes adecuado.

ADVERTENCIA

The improper connection of the

equipment grounding conductor can

result in a risk of electric shock. Check with a qualified

electrician or service representative if you are in doubt that

the appliance is properly grounded. Do not modify the plug

provided with the appliance; if it will not fit the outlet, have

a proper outlet installed by a qualified technician.

WARNING

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electric Code, ANSI/

NFPA

70 – latest edition, and all local codes and ordinances.

This appliance must have:

• 120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused

electrical supply.

•

Wiring must be 2 wire with ground and rated for 75°C (167°F).

• If the electrical supply does not meet the above

requirements, call a licensed electrician before proceeding.

It is recommended to have:

• A circuit breaker or time-delay fuse.

• A properly grounded individual branch circuit.

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and be

connected to the

equipment-grounding terminal or lead on

the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance

for electric current. This appliance is equipped with a cord

having an equipment-grounding conductor and a grounding

plug. The plug must

be plugged into an appropriate outlet

that is installed and grounded in accordance with all local

codes and ordinances.

Con los modelos equipados

con cable de corriente: No

modifique el enchufe provisto con el electrodoméstico;

si no coincide con el tomacorriente, solicite la instalación

de un tomacorriente apropiado a un electricista

calificado.

ADVERTENCIA

For models equipped with power

cord: Do not modify the plug

provided with the appliance; if it will not fit the outlet,

have a proper outlet installed by a qualified technician.

WARNING

Water Line Connection

• If using a flexible braided supply hose, label

the hose with the installation date to use as

reference. Flexible braided hoses, elbows and

gaskets should be replaced in 5 years.

• Turn off the water supply.

• Install a hand shut-off valve in an accessible

location, such as under the sink. (Optional, but

strongly recommended and may be required by local

codes.)

• Water connection is on the left side of the

dishwasher. Install the hot water inlet line, using no

less than 3/8” copper tubing or a flexible braided

hose. Route the line as shown in PREPARE HOT

WATER LINE section and extend forward at least

19” from rear wall.

• Adjust water heater for 120°F to 140°F temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120

PSI.

Turn page to begin dishwasher installation.

Installation Preparation

PREPARE HOT WATER LINE

NOTE: We recommend copper tubing for the water

line, but if you choose to use flexible hose, use GE

Appliances WX28X326, flexible braided hose.

• The water supply line (3/8” copper tubing or flexible

braided hose) may enter from either side, rear or

floor within the shaded area shown in figure.

• The water supply line may pass through the same

hole as the electrical cable and drain hose. Or, cut

an additional 1-1/2" diameter hole to accommodate

the water line. If power cord with plug is used, water

line must not pass through power cord hole.

Cabinet Face

Shut-off

Valve

2" From Floor

19" From Wall

From

Cabinet

Hot

1-1/2”

Dia.

Hole

STEP 1

PREPARATION

Locate the items in the installation package:

• Screws

• Junction box cover

• Drain hose and clamp

• Mounting brackets

• Trim pieces (on some models)

• Drain hose hanger

• Insulation pieces (some models)

• Toekick (pre-installed on some models)

• Owner’s Manual

• Product samples and/or coupons

Dishwasher Installation

STEP 2

CHECK DOOR BALANCE

(CONT.)

CHECK DOOR BALANCE

To check the door balance, hold the top of the

dishwasher firmly.

• Check the door balance by opening and closing the

door.

STEP 2

Tip: Make sure door opens and closes smoothly.

Check door opening and closing. If door does not open

easily or falls too quickly, check spring cable routing.

The cable is held in place by “shoulders” on the pulley.

Check to be sure cable has not slipped over the pulley

shoulders and is routed as shown.

Make sure

pulley cable

is within

pulley

shoulders

Front View

Opening the door will cause the

dishwasher to tip forward when it

is not fully installed. When opening

the door prior to the dishwasher

being fully installed, hold the top of

the dishwasher securely with one hand and hold the

door with the other hand. Gloves should be worn.

CAUTION

Abrir la puerta hará que el lavavajillas

se incline hacia adelante cuando

no se encuentre completamente

instalado. Al abrir la puerta antes

de haber instalado completamente

el lavavajillas, sostenga la parte superior del

lavavajillas de forma segura con una mano y

sostenga la puerta con la otra mano. Se deberán

usar guantes.

PRECAUCIÓN

• Door is properly

balanced if,

when opened, it

self closes within

20° from vertical,

stays in position

from 20° to 70°

and falls fully

open beyond 70°.

Door

closes

within

20°

Door stays in

position from

20° to 70°

Door falls fully

open beyond 70°

Side View

NOTE: Springs are not adjustable.

STEP 5

POSITION WATER LINE

AND HOUSE WIRING

• Position water supply line and house wiring on the

floor of the opening to avoid interference with base

of dishwasher and components under dishwasher.

STEP 6

INSTALL DRAIN HOSE,

THROUGH CABINET

• Detach the hose from the tub at locations indicated.

NOTE: Do not remove high drain loop.

Dishwasher Installation

Water

Line

House

Wiring

STEP 4

INSTALL 90° ELBOW

• Thread 3/4” GHT 90°

elbow onto the water

valve. Ensure rubber

gasket is located

between valve and

elbow.

• Do not overtighten

elbow. Water valve

bracket could bend or

water valve fitting could

break.

• Position the end of the

elbow to face the rear

of the dishwasher.

Water

Valve

Bracket

Fill Hose

Front of dishwasher

90° Elbow

STEP 3

REMOVE WOOD BASE,

INSTALL LEVELING LEGS

NOTE: Some models have an attached wood base.

IMPORTANT – Do not kick off wood base!

Damage will occur.

• Move the dishwasher close to the installation location

and lay it on its back. NOTE: Do not place the

dishwasher on its side.

• For models with an attached wood base, remove the

4 leveling legs on the underside of the wood base

with a 15/16” socket wrench.

• Discard wood base.

• With a 15/16” socket wrench adjust leveling legs into

the dishwasher frame, approximately 1/2” from frame

as shown.

Do not remove wood base until you are ready to

install the dishwasher. The dishwasher will tip over

when the door is opened if base is removed.

CAUTION

No quite la base de madera hasta que esté listo

para instalar el lavaplatos. Si se quita la base, el

lavaplatos se volcará cuando se abra la puerta.

PRECAUCIÓN

Approx

1/2"

Discard wood base

Remove

hose,

from

these

areas

only,

needed

Do NOT

remove

hose from

here (high

drain loop

area).

Dishwasher Installation

SLIDE DISHWASHER

THREE-FOURTHS OF

THE WAY INTO CABINET

IMPORTANT – Do not push against front panel with

knees. Damage will occur.

•

Grasp the sides of the front panel and slide

dishwasher into the opening a few inches at a time.

STEP 7

Do not push against

front door panel with

knee. Damage to the

door panel will occur.

INSTALL TRIM PIECES

In this step you will need the trim pieces set aside in Step 1.

• Select the top trim piece and line up center to the

top latch. Press the trim piece onto the tub flange

moving from one side to the other.

•

Select the left trim piece. Align top edge with the top

trim and press it onto the left side of the tub flange

moving from the top to the bottom. Repeat for the

right side tub flange trim piece.

Top

View

Handle

Door

Tub trim

Tub frame

STEP 8

Side Trim

Side

Trim

Top View

Side

Trim

Top Trim

(on some models)

Fully seat to tub flange

SLIDE DISHWASHER

THREE-FOURTHS OF

THE WAY INTO CABINET

(CONT)

• As you proceed, pull the drain hose through the

opening under the sink. Stop pushing when the

dishwasher extends about 6 inches forward of

adjacent cabinets.

• Make sure drain hose is not kinked under or behind

the dishwasher.

• Make certain the house wiring, drain line and

water line do not interfere with components under

dishwasher.

STEP 7

STEP 6

INSTALL DRAIN HOSE,

THROUGH CABINET (CONT)

• Position dishwasher in front of cabinet opening.

Insert drain hose into the hole in cabinet side. If

a power cord is used, guide the end through a

separate cabinet opening.

Tip: Prevent unnecessary service call charges for

fill, drain or noise concerns.

Position utility lines so they do not interfere with

anything under or behind the dishwasher.

Reposition the insulation blanket over the collar, as

shown.

House

Wiring

Power Cord

(If used)

Drain

Hose

Water

Line

Insulation

Blanket

Ensure drain hose is not

twisted or pinched

Maximum drain hose

length is 16' from the

rear of the dishwasher

Do not disconnect or remove high

drain loop from left side of dishwasher

Pull insulation

blanket over

collar

Dishwasher Installation

INSTALL MOUNTING

BRACKETS

You will need the mounting brackets set aside in

Step 1.

You must install the mounting brackets onto the

dishwasher tub frame top OR sides prior to sliding the

dishwasher into place under the countertop.

Install mounting brackets on top if the

underside of countertop is wood or wood-like

material that accepts screws:

Install the brackets by inserting the tabs through the

slots on the tub frame as shown. NOTE: You may

need to work the tabs through the slots.

Using pliers, bend and twist the tabs upward to secure

as shown.

IMPORTANT - After installing brackets and before

closing the dishwasher door, adjust the brackets

by bending them up as needed, so that they do not

contact the top of the dishwasher door and cause

damage.

•

If you are installing the dishwasher under a counter

with a short overhang, the countertop brackets may

extend beyond the edge of the counter. If this is

the case, remove the excess length by repeatedly

bending the brackets at the front notch only until they

break.

PUSH DISHWASHER INTO

FINAL POSITION

•

Check the tub insulation blanket, if equipped, to be

sure it is smoothly wrapped around the tub. It should

not be “bunched up” and it must not interfere with

the door springs. If the insulation is “bunched up” or

interfering with the springs, straighten and re-center

the blanket prior to sliding the dishwasher into its

final position.

•

Slide the dishwasher into the final position by

pushing on the sides of the door panel. Do not push

or pull the door in a partially open or closed position

when moving the dishwasher. Do not use a knee or

push on the center of the panel. If you do, damage

to the panel will likely result.

•

The dishwasher is in the final position when the

edges of the front panel are flush with the adjacent

cabinets and the dishwasher is centered in the

cabinet opening. Check that the dishwasher is

squarely positioned in the cabinet opening at both

the top and the bottom of the appliance prior to

mounting to the cabinet.

IMPORTANT – Before opening the dishwasher door,

be certain the edges of the dishwasher door panel are

behind the face of the adjacent cabinet and not up

against the cabinet face. Refer to figure below. If the

dishwasher door is opened when the edge of the door

is against the face of the cabinet, dishwasher door

damage and cabinet damage will occur.

STEP 9

INSTALL MOUNTING

BRACKETS (CONT.)

Install mounting brackets on sides if the

countertop is granite or similar material that

will not accept wood screws:

• Break off front portion of the bracket with pliers at the

location shown prior to attaching to dishwasher.

• Install the brackets by inserting the tabs through the

slots on the tub frame as shown. NOTE: You may

need to work the tabs through the slots.

Using pliers, bend and twist the tabs to secure as

shown.

STEP 9

STEP 10

Top

Mounting

Insert the bracket tabs

into the tub slots

Using pliers,

bend and

twist the

tabs

upward

to secure

Bracket

Bend and break here

after installing if

counter has a short

overhang.

Tub Frame

Side Mounting

Bend and break

here as necessary

Insert the

bracket

tabs into

the tub

slots

Using pliers,

bend and twist

the tabs upward to

secure

Bracket

Tub Frame

Dishwasher Installation

PUSH DISHWASHER

INTO FINAL POSITION

(CONT.)

•

Check dishwasher alignment prior to opening

dishwasher door to prevent panel damage.

•

Open and close the dishwasher door to be sure it

operates smoothly, and does not rub on the adjacent

cabinet.

Tip: Prevent unnecessary service charges for

panel damage or wash performance.

Make sure utility lines are not trapped or crushed behind

dishwasher. Crushed lines will restrict water flow.

LEVEL DISHWASHER

IMPORTANT – Dishwasher must be level for proper

dish rack operation, wash performance and door

operation. The dishwasher must be leveled left to right

and front to back. This ensures the dish racks will not

roll in or out on their own, circulation water will flow to

the pump inlet, and the door will close without hitting

the side of the tub.

•

Remove the lower dish rack and place a level on the

door and lower rack track as shown in figure.

•

Adjust the level of the dishwasher by individually

turning the 4 legs on the bottom of the dishwasher as

shown. Ensure all 4 legs are firmly in contact with the

floor.

• The dishwasher is properly leveled when the level

indicator is centered left to right and front to back.

Also, the dishwasher door should close without hitting

the side of the tub.

• Replace the lower rack.

Tip: Prevent unnecessary service charges. Verify

dishwasher is leveled.

Pull the dish racks half way out. They should stay put.

Open and close the door. The door should fit in the

tub opening without hitting the side of the tub. If the

racks roll on their own, or the door hits the side of tub,

re-level the dishwasher.

STEP 10 STEP 11

Check that tub trim does not

contact the door at all points

Tub trim may be trimmed if

necessary to ensure proper

door operation

Top

View

Handle

Door

Tub trim

Tub frame

Do not allow tub trim to get

trapped by or come into

contact with the door

Top

View

Tub trim

trapped

by door!

Cabinet

Turn Legs

to Adjust

Correct

Alignment

Door

Fits and

Swings

Back

Behind

Cabinet

Frame

Door Catches

on Cabinet Frame

Incorrect Alignment

will result in door damage

Dishwasher Installation

POSITION DISHWASHER,

SECURE TO COUNTERTOP

OR CABINET

In this step you will need the 2 Phillips special head

screws from the screws set aside in Step 1.

The dishwasher must be secured to the countertop or

the cabinet sides. When the underside of the countertop

is wood, use Method 1. Use Method 2 when the

underside of the countertop is made of a material, such

as granite, that will not accept wood screws.

IMPORTANT – Prevent door panel and control

panel damage. Dishwasher must be positioned so

the front panel and control panel do not contact the

adjacent cabinets or countertop. The unit should be

centered between the 2 cabinets. Mounting screws

must be driven straight and flush. Protruding screw

heads could scratch the door panel or control panel

and interfere with door operation.

Method 1

Secure dishwasher to underside of wood countertop.

• Re-check alignment of the dishwasher in the cabinet.

Refer to Steps 12 and 13. Door panel and/or control

panel must not hit cabinets or countertop.

• Fasten the dishwasher to the underside of the

countertop with the 2 Phillips special head screws.

Refer to figure. Make certain screws are driven

straight and flush to prevent panel damage.

• Plug buttons must be installed to ensure proper door

to tub alignment. Install plug buttons to the side of the

tub well in the holes provided.

Method 2

Secure dishwasher to cabinet sides.

• Recheck alignment of the dishwasher in the cabinet.

Refer to Steps 12 and 13. Door panel and/or control

panel must not hit cabinets or countertop.

• Fasten the dishwasher to the adjacent cabinets with

the 2 Phillips special head screws provided. Refer to

figure. Make certain screws are driven straight and

flush to prevent panel damage. Do not screw into

the cabinet face frame.

• Plug buttons must be installed to ensure proper door

to tub alignment. Install plug buttons to the side of

the tub in the holes provided.

CONNECT WATER

SUPPLY

Connect water supply line to 90° elbow.

If using a flexible braided hose connection:

• Attach nut to 90° elbow using an adjustable wrench.

If using a copper tubing connection:

•

Slide compression nut, then ferrule over end of water

line.

• Insert water line into 90° elbow.

•

Slide ferrule against elbow and secure with

compression nut.

IMPORTANT – Check to be sure that door spring and/

or door spring cable do not rub or contact the fill hose

or water supply line. Test by opening and closing the

door. Re-route the water supply lines if a rubbing noise

or interference occurs.

Solid Surface Countertop

Side Brackets

Plug buttons

Screw

Compression

Nut

Hot Water

Supply Line

90° Elbow

Ferrule

Bottom Left Side

STEP 12

POSITION DISHWASHER,

SECURE TO COUNTERTOP

OR CABINET (CONT.)

• Re-check that the dishwasher is squarely positioned

in the cabinet at both the top and bottom of the

appliance after mounting to the cabinets/countertop.

Adjust if necessary.

• Confirm all leveling legs are in contact with the floor

to prevent the dishwasher from rocking and ensure

proper door and latch operation

STEP 12

STEP 13

Brackets

Wood Countertop

Brackets

Wood Countertop

Plug buttons

Screw Screw

CONNECT DRAIN LINE

(CONT.)

• Connect drain line to air gap, waste tee or disposer

using the previously determined method. Secure

hose with a hose clamp.

Method 1 – Air gap with waste tee or disposer

Method 2 – “High drain loop” with waste tee or

disposer

With this method you will need the drain hose hanger

set aside in Step 1.

Fasten drain hose to underside of countertop with the

provided hanger.

IMPORTANT – When connecting drain line to

disposer, check to be sure that drain plug has been

removed. DISHWASHER WILL NOT DRAIN IF PLUG

IS LEFT IN PLACE.

Tip: Avoid unnecessary service call charges for a

no drain complaint.

Make sure excess drain hose has been pulled through

the cabinet opening. This will prevent excess hose

in the dishwasher cavity from becoming kinked or

crushed by the dishwasher.

Dishwasher Installation

Remove

Drain

Plug

CONNECT DRAIN LINE

• The hose should have already been detached from the

tub at locations indicated. NOTE: Do not remove high

drain loop.

The molded end of the drain hose will fit 5/8” through

1” diameter inlet ports on the air gap, waste tee or

disposer.

• Determine size of inlet port.

• Cut drain hose connector

on the marked line, if

required, to fit the inlet

port.

• If a longer drain hose is required, you can purchase

an extension drain hose - GE Appliances service

part WD24X10062 (4’ length) or WD24X10065

(12’ length) which can be connected directly to the

drain hose already attached to the unit. To use the

extension, you must cut the drain hose provided with

the unit as shown. Use a hose cutter or razor blade

knife to cut the drain hose.

• TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED

16’ FROM THE REAR OF THE DISHWASHER FOR

PROPER DRAIN OPERATION.

STEP 14 STEP 14

Remove

hose,

from

these

areas

only,

needed

Do NOT

remove

hose from

here (high

drain loop

area).

1”

5/8”

Cutting Line

IMPORTANT: Do not cut

corrugated portion of hose

Hose

Clamp

Cut Line

Dishwasher

Connection

House

Drain Hose on

Dishwasher

To use the 12’ drain hose extension:

Only cut ONE of these two locations

To use the 4’ drain

hose extension:

Only cut at this

location

72”

max.

Waste Tee Installation

72”

max.

Disposer Installation

Drain Hose Hanger

18”

min.

32” min. -

72” max.

Waste Tee Installation

Drain Hose Hanger

18”

min.

32” min. -

72” max.

Disposer Installation

Dishwasher Installation

CONNECT POWER SUPPLY

If a power cord with plug is already installed

proceed to Step 18.

In this step you will need the junction box cover and the

#10 Hex head screw from the screws set aside in Step 1.

• Secure house wiring to the back of the junction box

with a strain relief as shown in the MATERIALS YOU

WILL NEED section.

• Locate the 3 dishwasher wires, (white, black and green)

with the stripped ends coming out of the AC jumper. Use

UL-listed wire nuts of appropriate size to connect incoming

ground to green, white to white and black to black.

• Install the junction box cover using #10 hex head screw.

Check to be sure that wires are not pinched under the

cover and that all wire nuts are inside the cover.

• Make sure that the junction box cover is resting on

the mounting bracket.

To reduce the risk of electric shock, fire, or injury to

persons, the installer should check to ensure that wires

are not pinched or damaged, the house wiring is attached

to the junction box bracket through a strain relief, and

all electrical connections made at the time of install (wire

nuts) are contained inside of the junction box cover.

WARNING

STEP 15

PRETEST CHECKLIST

Review this list after installing your dishwasher to

avoid charges for a service call that is not covered

by your Warranty.

• Check to be sure power is OFF.

• Open door and remove all foam and paper

packaging.

• Locate the Owner’s Manual set aside in Step 1.

• Read the Owner’s Manual for operating instructions.

• Check door opening and closing. If door does not

open and close freely, check for proper routing of

spring cable over pulley. If door drops or closes

when released, adjust spring tension. See Step 2.

• Check to be sure that wiring is secure under the

dishwasher, not pinched or in contact with door

springs or other components. See Step 17.

• Check door alignment with tub. If door hits tub, level

dishwasher. See Step 13.

• Check door alignment with cabinet. If door hits

cabinet, reposition dishwasher. See Step 12.

• Pull lower rack out, about halfway. Check to be sure

it does not roll back or forward on the door. If the

rack moves, adjust leveling legs. See Step 13.

• Check that door spring does not contact water line,

fill hose, wiring or other components. See Step 12.

• Verify water supply and drain lines are not kinked

or in contact with other components. Contact with

motor or dishwasher frame could cause noise.

• Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must be

between 120°F and 140°F. A minimum of 120°F

temperature is required for best wash performance.

See PREPARE HOT WATER LINE section.

• Add 2 quarts of water to the bottom of the

dishwasher to lubricate the pump seal.

• Turn on water supply. Check for leaks. Tighten

connections if needed.

• Remove protective film if present from the control

panel and door.

• Check that tub trim does not contact the door.

STEP 16

Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador deberá realizar un

control para asegurar que los cables no estén pellizcados

ni dañados, que el cableado del hogar esté conectado a la

ficha de la caja de empalmes a través de un amortiguador

de refuerzo, y que todas las conexiones eléctricas realizadas

en el momento de la instalación (tuercas para cables) estén

dentro de la tapa de la caja de empalmes.

ADVERTENCIA

NOTE: All ground screws, brackets and wires must remain intact.

Junction

Box Cover

Ground

(Green)

AC Power

Connector

White

Ground

Screw

Strain

Relief

BlackJunction

Box

Bracket

Dishwasher Installation

DISHWASHER WET TEST

• Turn on power supply or plug power cord into outlet,

if equipped.

• Select a cycle to run and push the Start/Reset pad.

• Ensure the door is latched. Dishwasher should start.

• Check to be sure that water enters the dishwasher.

If water does not enter the dishwasher, check to be

sure that water and power are turned on.

• Check for leaks under the dishwasher. If a leak

is found, turn off power at the breaker, and then

tighten water connections. Restore power after leak

is corrected.

NOTE: A small amount of water may splash out of

the fill funnel, on the right side of the tub, during the

first use after installation. Splash-out is most likely to

occur if there is air in the water supply line from new

construction or if the valve has been closed for an

extended time.

• Check for leaks around the door. A leak around

the door could be caused by door rubbing or

hitting against adjacent cabinets. Reposition the

dishwasher if necessary. See Step 12.

• Press and hold the Start/Reset pad for 3 seconds to

cancel the cycle. The unit will begin to drain. Check

drain lines. If leaks are found, turn off power at the

breaker and correct plumbing as necessary. Restore

power after corrections are made. See Steps 6, 7, 8,

9 and 16.

• Open dishwasher door and make sure all of the

water has drained. If not, check that disposer plug

has been removed and/or air gap is not plugged.

Also check drain hose to be sure it is not kinked

underneath or behind dishwasher. See Step 16.

• Press Start/Reset pad once again and run

dishwasher through another cycle. Check for leaks and

correct if required.

• Repeat these steps as necessary.

POSITION SOUND

BARRIER AND INSULATION

(on some models)

Skip this step if the sound barrier is assembled

to the dishwasher.

• Locate the sound insulation package inside the

dishwasher.

• Locate the control box.

• Apply the insulation to the underside of the control

box and flush with its front face as shown.

Insulation shown correctly placed along the bottom

edge of the control box, the dishwasher bottom and

flush with the front face.

If the insulation has an extension piece (on

some models) follow these additional steps:

• Open door all the way, if the door doesn’t stay fully

open, adjust the insulation panel.

• Align the screw holes with the screw holes on the

legs of the dishwasher.

• Ensure vent opening is not blocked by insulation.

STEP 17 STEP 18

Control

Box

Junction Box

Cover

(on some models)

Junction Box

Cover

Vent opening should be properly

aligned with cutout in the insulation

Dishwasher Installation

LITERATURE

•

Be sure to leave complete literature package, these Installation

Instructions and product samples and/or coupons with the

consumer.

INSTALL TOEKICK

NOTE: On some models the toekick may come

pre-installed.

• Remove the 2 screws installed on the front brace.

• Place toekick against the legs of the dishwasher.

• Align the toekick with the bottom edge and make

sure it is against the floor.

• Insert and tighten the 2 toekick attachment screws.

The toekick should stay in contact with the floor.

NOTE: Be careful not to over-tighten the screws in

the toekick.

• When reinstalling the toekick, on models with a sound

barrier, ensure that the bottom edge is flush with

the floor. Any excess material should be tucked up

behind the outer door.

Tip: Reduce sound from under the dishwasher.

Make sure toekick is against floor.

Attachment

Screws

Toekick

CHECK THE FOLLOWING

• Tub trim does not interfere with the door

• Dishwasher is square and level at both the top and

bottom of the cabinet opening, with no twisting or

distortion of the tub or door

• All 4 legs of the dishwasher are firmly in contact with

the floor

• Drain hose is not pinched between the dishwasher

and adjacent cabinets or walls

• Tub trim is fully seated on the tub flange

STEP 19

STEP 20

STEP 21

Remove these two screws

NOTE: Product improvement is a continuing endeavor. Therefore, materials,

appearance and specifications are subject to change without notice.

Printed in the United States

POUR VOTRE SÉCURITÉ

Veuillez lire et observer toutes les mises en garde

(AVERTISSEMENT et ATTENTION) données dans les

présentes directives.

Pour effectuer l’installation décrite dans les présentes

directives, il faut porter des gants et des lunettes de

sécurité.

IMPORTANT – Observez tous les codes et ordonnances

en vigueur.

• Note à l’installateur – Veuillez laisser les présentes

directives au consommateur pour l’inspecteur local.

• Note au consommateur – Veuillez conserver les

présentes directives avec votre Manuel d’utilisation

pour consultation ultérieure.

• Compétences requises – L’installation de ce

lave-vaisselle exige des compétences de base

en mécanique, en électricité et en plomberie.

L’installateur est responsable de la qualité

de l’installation. Toute défaillance du produit

attribuable à une installation inadéquate n’est

pas couverte par la garantie de GE Appliances.

Reportez-vous à la garantie du produit.

• Durée de l’installation – Entre 1 et 3 heures.

L’installation d’un nouveau lave-vaisselle exige plus de

temps que le remplacement d’un ancien modèle.

IMPORTANT – Le lave-vaisselle DOIT être installé de

manière à ce qu’il puisse être sorti de son emplacement

si des réparations sont nécessaires.

Il importe d'user de prudence lorsque l'appareil est

installé ou déplacé afin de prévenir l'endommagement

du cordon d'alimentation.

Si le lave-vaisselle que vous avez reçu est endommagé,

communiquez immédiatement avec votre détaillant ou

l’entrepreneur en construction.

Accessoires facultatifs – Reportez-vous au Manuel

d’utilisation pour connaître les ensembles pour panneau

décoratif personnalisé offerts.

Votre lave-vaisselle est un appareil qui chauffe l’eau.

VEUILLEZ LIRE ATTENTIVEMENT

CONSERVER CES DIRECTIVES

AVANT DE COMMENCER

Veuillez lire attentivement toutes les directives qui suivent.

• Avant de commencer l’installation, coupez toute

alimentation menant de l’appareil au disjoncteur ou

au fusible. Dans le cas contraire, vous pourriez être

victime d’une décharge électrique.

• Pour réduire les risques de choc électrique,

d’incendie ou de blessures, l’installateur doit

s’assurer que le lave-vaisselle est complètement

encastré au moment de l’installation.

• Un branchement inadéquat du conducteur de

mise à la terre peut présenter des risques de choc

électrique. Si vous n’êtes pas certain que l’appareil

est correctement mis à la terre, consultez un

réparateur ou un électricien qualifié. Si le câblage

électrique de la résidence n’est pas constitué de

deux fils plus un fil de mise à la terre, l’installateur

doit installer un fil de mise à la terre. Si le câblage

électrique de la résidence est en aluminium, utilisez

un agent antioxydant et des connecteurs pour

raccords «aluminium-cuivre» homologués UL.

•

Pour réduire les risques de choc électrique, d’incendie ou

de blessures, l’installateur doit vérifier pour s’assurer que

les fils ne sont pas pliés ou en dommagés, que le câblage

domestique est fixé au support de boîte de connexion par

l’entremise d’un serre-câble et que toutes les connexions

électriques faites au moment de l’installation (capuchons

de connexion) se trouvent à l’intérieur du couvercle de la

boîte de connexion

AVERTISSEMENT

Instructions

D’Installation

Lave-vaisselle encastré

Consultez votre Manuel du Propriétaire pour plus de détails sur la façon de nous contacter concernant les

questions d’installation

Ouvrir la porte causera le

basculement du lave-vaisselle

vers l’avant si son installation n’est pas complètement

terminée. Pour ouvrir la porte avant la finalisation

de l’installation, agrippez le haut du lave-vaisselle

fermement avec une main et tenir la porte de l’autre

main. Le port de gants est nécessaire.

ATTENTION

Préparation pour l’installation

PIÈCES FOURNIES

DANS L’EMBALLAGE :

• Couvercle de la boîte de jonction

• Vis à tête hexagonale n° 10

• Collier

• Support de tuyau de vidange

• 2 Boutons de bouchon

• Plinthe (préinstallée sur certains modèles)

• 2 Moulure de cuve (certains modèles)

• 2 Supports de montage pour comptoirs ou

armoires latérales en bois

• 2 Vis à tête spéciale Phillips n° 8-18 x 15,8 mm

(5/8 po) pour fixer le lave-vaisselle au dessous

du comptoir ou armoires latérales

• Pièces isolantes (certains modèles)

• Documentation, échantillons et(ou) bons

OUTILS NÉCESSAIRES :

• Tournevis cruciforme

• Tournevis à douille de 5/16 po et 1/4 po

• Clé à molette de 15 cm (6 po)

• Niveau

• Équerre de menuisier

• Ruban à mesurer

• Lunettes de sécurité

• Lampe de poche

• Seau pour attraper l’eau lors de la purge du tuyau

• Douille de 15/16 po

• Gants

• Pince

Pour une nouvelle installation :

• Coupe-tube

• Perceuse et mèches appropriées

• Jeu de scie-cloche

MATÉRIAUX NÉCESSAIRES :

• &RXGHÛGHôSR*+7*DUGHQ+RVH7KUHDG)LOHWDJH

à boyau d’arrosage) (joint d’étanchéité inclus) – Avec bout

opposé dimensionné pour la conduite d’eau chaude

• Ruban pour joints filetés

• Connecteurs vissables homologués UL (3)

• Ruban-cache

Pour une nouvelle installation :

• Coupure anti-refoulement pour le boyau de vidange, si nécessaire

• Raccord en T pour la plomberie de la résidence, s’il y a lieu

• Trousses de câbles électriques ou de cordons

électriques WXO9X70910 (1,65 m (5 pi 5 po de long)) ou

WX09X70911 (2,41 m (7 pi 11 po de long)) uniquement

• Bague anti-traction pour le raccordement électrique

• Colliers

• Robinet d’arrêt (recommandé)

• Conduite d’eau chaude – 9,5 mm (3/8 po) minimum, tuyau

en cuivre (incluant la bague et l’écrou à compression) ou

la pièce WX28X326 de GE, boyau métallique flexible.

• Boyau de vidange de 3,7 m (12 pi) de long WD24X10065

ou boyau de vidange de 1,2 m (4 pi) de long

WD24X10062 si nécessaire

Scie-cloche

Ruban à mesurer

Coupe-tube

Perceuse et

mèches

Tournevis

cruciforme

Douille de 15/16

Tournevis à douille

de 5/16 po et 1/4 po

Seau

Lampe de poche

Gants

Équerre de

menuisier

Lunettes de sécurité

Niveau

Couvercle

de la boîte

de jonction

Vis à tête

hexagonale n° 10

de 9,5 mm (3/8

po) de long pour

boîte de jonction

Documentation

Pince

Optionnel -

Boyau de vidange de 3,7 m (12 pi) - WD24X10065

Boyau de vidange de 1,2 m (4 pi) - WD24X10062

Coude de 90°

Robinet

d’arrêt

Boutons de

bouchon

Ruban-cache

Plinthe

Isolement

(certains modèles)

Supports de

montage

Support de tuyau de

vidange

Clé à molette

de 15 cm (6 po)

Connecteurs

vissables (3)

Vis à tête

spéciale Phillips

n° 8 de 15,8 mm

(5/8 po) de long

Raccord

en T

Coupure anti-

refoulement

Bague anti-

traction

Câble électrique

(ou cordon

d’alimentation,

s’il y a lieu)

Ruban pour

joints filetés

(s’il y a lieu)

Moulure de cuve

(sur certains modèles)

Collier

Colliers

Conduite

d’eau

chaude

PRÉPARATION DE L’OUVERTURE

DANS LES ARMOIRES

• L’ouverture dans les armoires doit mesurer au moins 61,0 cm (24

po) de largeur et de profondeur, et environ 87,6 cm (34-1/2 po)

de hauteur à partir du plancher jusqu’au-dessous du comptoir.

• Le lave-vaisselle doit être installé de façon à ce que le boyau

de vidange mesure au maximum 4,88 mètres (16 pieds) pour

assurer une vidange adéquate.

• Le dessus, les côtés et l’arrière du lave-vaisselle doivent être

complètement dissimulés à l’intérieur de l’ouverture. Le lave-vaisselle

ne doit soutenir aucune partie de la structure des armoires.

DÉGAGEMENTS:

• Dans le cas

d’une installation

dans un coin,

veuillez prévoir

un dégagement

d’au moins 5,1

cm (2 po) entre

le lave-vaisselle

et les armoires,

le mur ou un

électroménager

adjacent. Veuillez

prévoir un

dégagement d’au

moins 65 cm (25-1/2 po) à l’avant du lave-vaisselle pour

l’ouverture de la porte.

Préparation pour l’installation

33-1/2 po to 34-3/4

po du dessous

du comptoir au

plancher

Le mur du fond

doit être exempt

de tuyaux ou

de fils

La partie ombrée est

réservée à la plomberie et

à l’électricité

Armoires à

l’équerre et

d’aplomb

61,0 cm

(24 po) min.

15,2 cm (6 po)

61,0 cm

(24 po) min.

10,1 cm

(4 po)

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

25-1/2"

Comptoir

Lave-vaisselle

5,1 cm (2 po) minimum

pour l’ouverture de la porte

65 cm (25-1/2 po)

EXIGENCES RELATIVES AU

SYSTÈME DE VIDANGE

• Veuillez observer les ordonnances et les codes locaux en vigueur.

• Le boyau de vidange doit avoir une longueur maximale de 4,88

mètres (16 pieds).

REMARQUE : Il faut installer une coupure anti-refoulement si le

raccord au broyeur à déchets ou au raccord en T se trouve à moins

de 46 cm (18 po) au-dessus du plancher afin d’éviter un siphonage.

CHOIX DE LA MÉTHODE DE VIDANGE

Le type d’installation de vidange dépend des conditions suivantes.

• Les ordonnances ou codes locaux en vigueur exigent-ils une

coupure anti-refoulement?

• Le raccord T se trouve-t-il à moins de 46cm (18po) du plancher?

Si vous répondez OUI à l’une ou l’autre de ces

questions, vous DEVEZ utiliser la méthode n° 1.

• Si vous répondez NON, vous pouvez employer l’une ou l’autre

des méthodes.

PRÉPARATION DES ARMOIRES

• Percez un trou de 3,8 cm (1-1/2 po) de diamètre dans la paroi de

l’armoire qui se trouve dans la partie ombrée de la PRÉPARATION

DE L’OUVERTURE DANS LES ARMOIRES pour le boyau de

vidange. Assurez-vous que l’orifice ne présente pas d’arêtes vives.

IMPORTANT – Lorsque vous branchez le boyau de vidange

à un broyeur à déchets, assurez-vous

d’enlever le bouchon de vidange. LE

LAVE-VAISSELLE NE POURRA PAS

SE VIDER SI VOUS LAISSEZ LE

%28&+21(13/$&(

Méthode n° 1 – Coupure anti-refoulement avec raccord en

T ou broyeur à déchets

Il faut installer une coupure anti-refoulement lorsqu’elle est exi-

gée par les ordonnances et les codes locaux en vigueur. Cette

coupure anti-refoulement doit être installée conformément aux

directives données par le fabricant.

Méthode n° 2 – Boucle de vidange élevée avec raccord en

T ou broyeur à déchets

Conseil: Pour éviter des frais de réparation inutiles.

Assurez-vous d’enlever le bouchon de vidange du broyeur à

déchets avant d’y brancher le boyau de vidange du lave-vaisselle.

Pour réduire les risques de

choc électrique, d’incendie

ou de blessures, l’installateur doit s’assurer que le

lave-vaisselle est complètement encastré au moment

de l’installation.

AVERTISSEMENT

Remove

Drain

Plug

Enlevez le

bouchon

de vidange

DIMENSION DE LA POIGNÉE DU LAVE-VAISSELLE : La

porte de ce lave-vaisselle doit être à niveau avec l’armoire.

Pour les modèles avec poignée, la profondeur totale (avec

poignée) est de 67,9 cm (26 ¼ po) maximum selon le modèle.

Consultez le document de spécifications rapides en ligne pour

obtenir plus de dimension de lave-vaisselles.

182,8 cm

(72 po)

max.

182,8 cm

(72 po)

max.

Crochet pour boyau de vidange

82 cm

(32 po)

min. -

182,8 cm

(72 po)

max.

46 cm

(18 po) min.

Crochet pour

boyau de vidange

46 cm

(18 po) Min.

82 cm

(32 po)

min. -

182,8 cm

(72 po)

max.

La page charge ...

GE GDF530PGMBB Guide d'installation

Marque: GE

Modèle: GDF530PGMBB

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE GDF530PGMBB Installation guide

GE GDF530PGMBB Guide d'installation

GE GDF530PGMBB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents