Samsung HW-LST70T Manuel utilisateur

HW-LST70T

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - 2

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - 3

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from excess heat (e.g. a

replace) or equipment creating strong

magnetic or electric elds. Unplug the power

cable from the AC wall socket if the unit

malfunctions. Your product is not intended

for industrial use. It is for personal use only.

Condensation may occur if your product has

been stored in cold temperatures. If

transporting the unit during the winter, wait

approximately 2 hours until the unit has

reached room temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or

equivalent type.

6. Despite the IP55 rating, your Soundbar is not

impervious to water damage in any situation.

To help prevent damage to your product,

avoid the product being subjected to:

• Water projected by a source greater than

6.3 mm against enclosure from any

direction or submersion in water;

• Water projected at greater than 30 KPa

(4.4 PSI) with a water volume greater

than 12.5 L/minute for more than

3 minutes; and

• Extreme weather conditions.

ENG - 4

CONTENTS

01 Checking the Components 6

Inserting Batteries before using the Remote Control

(AAA batteries X 2) ------------------------- 7

02 Product Overview 8

Front Panel / Bottom Panel of the Soundbar ------------------------- 8

Rear Panel of the Soundbar ------------------------- 9

03 Using the Remote Control 10

How to Use the Remote Control

-------------------------

10

Using the Hidden Buttons (Buttons with more than one function)

-------------------------

13

Output specications for the different sound effect modes

-------------------------

13

Adjusting the Soundbar volume with a TV remote control ------------------------- 14

04 Connecting the Soundbar 15

Connecting Electrical Power

-------------------------

15

How to mount the AC/DC adapter

-------------------------

15

05 Using a wired connection to the TV 16

Connecting using an Optical Cable

-------------------------

16

06 Using a wireless connection to the TV 18

Method 1. Connecting via Bluetooth

-------------------------

18

Method 2. Connecting via Wi-Fi

-------------------------

20

07 Connecting an External Device 21

Connecting using an Optical Cable

-------------------------

21

ENG - 5

08 Connecting a Mobile Device 22

Method 1. Connecting via Bluetooth

-------------------------

22

Method 2. Connecting via Wi-Fi (Wireless Network)

-------------------------

25

Using the Tap Sound

-------------------------

26

09 Connecting an Amazon product 27

Connect and use with an Amazon product (Amazon Echo) ------------------------- 27

Use voice commands to control the Soundbar

-------------------------

27

10 Installing the Wall Mount 28

Installation Precautions

-------------------------

28

Method 1. TV mount

-------------------------

28

Method 2. Wall mount

-------------------------

31

11 Software Update 33

Auto Update

-------------------------

33

USB Update

-------------------------

33

Initialisation

-------------------------

33

12 Troubleshooting 34

13 Licence 35

14 Open Source Licence Notice 36

15 Important Notes About Service 36

16 SpecicationsandGuide 37

Specications

-------------------------

37

ENG - 6

01 CHECKING THE COMPONENTS

Soundbar Main Unit Soundbar Remote Control

/

Batteries

Optical Cable

x 2

AC/DC Adapter Wall Mount Guide Holder-Screw

x 2

Bracket-Top Bracket-Bottom Bracket-Guide Bracket-Wall Mount

x 4

(M3 x L10)

x 2

(M4 x L10)

x 2

(M6 x L10)

x 2

(M5 x L50)

x 2

Screw-Taptype Screw-Machine Bolt-Etc A/S Bolt-Etc Anchor / Screw

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Bottom of the Soundbar Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

• For Soundbar wall mounting components, see pages 28~32.

• This Soundbar is intended only for TV mount or wall mount.

• Design, specications, and App screen are subject to change without prior notice.

• The appearance of the accessories may differ slightly from the illustrations above.

ENG - 7

Inserting Batteries before using the Remote Control

(AAA batteries X 2)

1

3

2

3

2

1. Press the ^ button at the top rear of the Soundbar remote control. The body will pop out slightly

from the body cover.

2. Turn the remote over, push the body of the remote upwards until the battery compartment is

revealed, and then remove the battery cover.

3. If there are batteries in the remote, to remove the existing batteries.

4. Insert two new batteries (1.5V AAA type) into the battery compartment making sure that the

batteries’ polarities (+, -) are oriented correctly.

5. Once the batteries have been inserted, attach the battery cover and then slide down the body of

the remote.

6. Turn the remote over, press and hold the ^ button on the top rear, and then slide the body of the

remote down into place.

• Alkaline batteries are recommended for longer battery life.

ENG - 8

02 PRODUCT OVERVIEW

Front Panel / Bottom Panel of the Soundbar

Bottom Panel

Position the product so that the SAMSUNG logo is located on the top.

󰟴

󰟳

󰟵 󰟶

󰟳

Display

Displays the product’s status and current mode.

󰟴

(Power) Button

Turns the power on and off.

󰟵

(Volume) Button

Adjusts the volume.

󰟶

(Source) Button

Selects the source input mode.

Input mode Display

Optical Digital input D.IN

Wi-Fi mode WIFI

BLUETOOTH mode BT

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and

change the TV speaker to External Speaker.

ENG - 9

Rear Panel of the Soundbar

SERVICE

DC 23V

DIGITAL

AUDIO IN

(OPTICAL)

SERVICE

DC 23V

DIGITAL

AUDIO IN

(OPTICAL)

󰟳

󰟴

󰟵

󰟳

DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device. (See page 21)

󰟴

SERVICE

Connect a USB storage device to upgrade the product's software.

󰟵

DC 23V (Power Supply In)

Connect the AC/DC power adapter. (See page 15)

• When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.

Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between

components are complete.

ENG - 10

03 USING THE REMOTE CONTROL

How to Use the Remote Control

󰟳

󰟵

󰟴

󰟶

󰟸

󰟹

󰟷

󰟺

󰟼

󰟻

󰟽

󰠀

󰟾

󰟿

󰟳

Power

Turns the Soundbar on and off.

• Auto Power Down Function

The unit turns off automatically in the following

situations:

– In D.IN / Wi-Fi / BT mode if there is no audio

signal for 18 minutes.

󰟴

D.IN

Press to enter the “D.IN” mode.

󰟵

Source

Press to select a source connected to the Soundbar.

󰟶

Mute

Press the (Mute) button to mute the sound.

Press it again to unmute the sound.

󰟷

Sound

Control

When pressed, the setting items such as TREBLE, or

SYNC are displayed in sequence. The desired item

can be adjusted using the Up/Down buttons.

– To adjust the TREBLE volume, select Sound

Control → TREBLE, and then use the Up/Down

buttons to adjust the volume within a -6 to +6

range.

– Press and hold the (Sound Control) button

for about 5 seconds to adjust the sound for each

frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz,

2.5kHz, 5kHz, and 10kHz are selectable using

the Left/Right buttons and each can be

adjusted to a setting between -6 to +6 using

the Up/Down buttons. (Make sure the Sound

mode is set to “STANDARD”.)

– If the video on the TV and audio from the

Soundbar are not synchronised, select SYNC in

Sound Control, and then set the audio delay

between 0~300 milliseconds by using the Up/

Down buttons.

– SYNC is only supported for some functions.

ENG - 11

󰟸

VOLUME

Push the button up or down to adjust the volume.

• Mute

Press the VOL button to mute the sound. Press it again to unmute the sound.

󰟹

STANDARD

Press this button to outputs the original sound.

󰟺

Bluetooth

PAIR

Switch the Soundbar to Bluetooth pairing mode. Press the button and wait for the “BT

PAIRING” screen to connect to a new Bluetooth device.

󰟻

Play / Pause

You can also play or pause music by pressing the button.

󰟼

Up/Down/

Left/Right

VOL WOOFER

SOUND

MODE

PAIR

Press the indicated areas to select Up/Down/Left/Right.

Press Up/Down/Left/Right on the button to select or set functions.

• Repeat

To use the Repeat function, press the Up button.

• Music Skip

Press the Right button to select the next music le. Press the Left button to select the

previous music le.

󰟽

Info

When pressed, the information for the connected sources and Bluetooth devices appears.

ENG - 12

󰟾

BASS

Push this button up or down to adjust the bass volume within a -6 to +6 range.

󰟿

ADAPTIVE

Press this button to analyzes the content in real time and automatically provides the optimal

sound eld based on the characteristics of the content.

󰠀

SURROUND

Press this button to provide a wider sound stage than standard.

ENG - 13

Using the Hidden Buttons (Buttons with more than one function)

Hidden Button

Reference page

Remote Control Button Function

BASS (Up) TV remote control On/Off (Standby) page 14

(Sound Control)

7 Band EQ page 10

Outputspecicationsforthedifferentsoundeffectmodes

Effect Input Output

STANDARD

2.0 ch 2.0 ch

5.1 ch 3.0 ch

SURROUND

2.0 ch 3.0 ch

5.1 ch 3.0 ch

ADAPTIVE

2.0 ch 2.0 ch

5.1 ch 3.0 ch

ENG - 14

Adjusting the Soundbar volume with a TV remote control

Adjust the Soundbar volume using the TV’s remote control.

• This function can be used with IR remote controls only. Bluetooth remote controls (remote

controls that require pairing) are not supported.

• Set the TV speaker to External Speaker to use this function.

• Manufacturers supporting this function:

VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA

1. Turn Off the Soundbar.

2. Push up and hold the BASS button for 5 seconds.

Each time you push the BASS button up and hold it for 5 seconds, the mode switches in the

following order: “SAMSUNG-TV REMOTE” (Default mode), “OFF-TV REMOTE”, “ALL-TV REMOTE”.

Remote Control Button Display Status

5 Sec

(Default mode)

SAMSUNG-TV REMOTE

Enable a Samsung TV’s IR remote

control.

5 Sec

OFF-TV REMOTE

Disable the TV remote control.

5 Sec

ALL-TV REMOTE

Enable a third-party TV’s IR

remote control.

ENG - 15

04 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Connect the Soundbar to an electrical outlet in the

following order:

1. Connect the AC/DC adapter to the Soundbar.

2. Connect the power cord to a wall socket.

• For more information about the required

electrical power and power consumption,

refer to the label attached to the product.

(Label: Bottom of the Soundbar Main Unit)

NOTES

• If you unplug and reconnect the power

cord when the product is turned on, the

Soundbar turns on automatically.

• Never forcibly pull the power cord of AC/

DC adapter.

• When installing the AC/DC adapter

horizontally, place it with the Samsung

logo facing upward.

• This product may not operate safely under

-20°C. It is recommended to connect the

power cable to the outlet and after 1 hour,

turn on the Soundbar power.

Rear of the Soundbar Main Unit

SERVICE

DC 23V

DIGITAL

AUDIO IN

(OPTICAL)

SERVICE

DC 23V

DIGITAL

AUDIO IN

(OPTICAL)

AC/DC Adapter

• While the cable is not in use, seal it with

waterproof silicone.

How to mount the AC/DC

adapter

• Tighten 2 or 4 screws (not supplied) on the

wall or table and then insert them into the

grooves on the rear of the AC/DC adapter.

You cannot install the adapter directly on

the oor.

• For the mounting screws, see the following

gures.

RecommendedScrewspecication

(not supplied)

L12

M3

6.5 mm

4.5 mm

ENG - 16

05 USING A WIRED CONNECTION TO THE TV

Connecting using an Optical Cable

When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on

your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on

the TV is changed, you will experience better sound quality. (The TV menu may use different words for

Dolby Digital and PCM depending on the TV manufacturer.)

Pre-connection Checklist

• When using the Soundbar outdoors, it is recommended to connect an Optical cable for smooth

sound output.

• Be sure to use the optical cable provided with the product.

• To purchase any optical cable separately, contact the nearest dealer or Samsung Service Centre.

• The optical cable provided with the product is designed to meet the specication (4 mm) for

waterproong. When using an optical cable purchased from other site, the waterproof function may

not work properly.

• When you use an optical cable and the terminals have covers, be sure to remove the covers.

SERVICE

DC 23V

DIGITAL

AUDIO IN

(OPTICAL)

OPTICAL OUT

Optical Cable

Rear of the Soundbar

D.IN

Bottom of the Soundbar

ENG - 17

1. With the TV and Soundbar turned off, connect the DIGITAL AUDIO IN (OPTICAL) port on the

Soundbar and the OPTICAL output port on the TV with the optical cable, as shown in the gure.

2. Turn on the Soundbar and TV.

3. Select “D.IN” mode by pressing the (Source) button on the bottom of the Soundbar or the D.IN

button on the Soundbar remote control.

4. The TV sound is output from the Soundbar.

ENG - 18

06 USING A WIRELESS CONNECTION TO THE TV

Pre-connection Checklist

• When used outdoors, wireless performance may degrade. Accordingly, use the provided optical

cable if possible.

Method 1. Connecting via Bluetooth

When a Samsung TV is connected using Bluetooth, you can hear stereo sound without the hassle of

cabling.

• Only one Samsung TV can be connected at a time.

• Samsung TV that supports Bluetooth can be connected. Check the specications of your TV.

Bottom of the Soundbar

OR

BT PAIRING

5 Sec

The initial connection

1. Press the PAIR button on the Soundbar remote control to enter the “BT PAIRING” mode.

(OR)

a. Press the (Source) button on the bottom panel and then select “BT”.

“BT” changes to “BT PAIRING” in a few seconds automatically or changes to “BT READY” if

there is a connect record.

b. When “BT READY” appears, press and hold the (Source) button on the bottom panel

of the Soundbar for more than 5 seconds to display “BT PAIRING”.

2. Select Bluetooth mode on the Samsung TV.

(e.g. Home ( )  Settings ( )  Sound  Sound Output  Bluetooth Speaker List 

[AV] Samsung Soundbar LST70T (Bluetooth))

ENG - 19

3. Select “[AV] Samsung Soundbar LST70T” from the list on TV’s screen.

An available Soundbar is indicated with “Needs Pairing” or “Paired” on the TV’s Bluetooth device

list. To connect the Samsung TV to the Soundbar, select the message, and then establish a

connection.

• When the Samsung TV is connected, [TV] Name → “BT” appears on the Soundbar’s front display.

4. You can now hear Samsung TV sound from the Soundbar.

• After you have connected the Soundbar to your Samsung TV the rst time, use the “BT READY”

mode to reconnect.

If the device fails to connect

• If you have an existing Soundbar (e.g., [AV] Samsung Soundbar LST70T) on the list of speakers

on the Samsung TV, delete it.

• Then repeat steps 1 through 3.

Disconnecting the Soundbar from the Samsung TV

Press the (Source)

button on the bottom panel or on the remote control and switch to any mode but

“BT”.

• Disconnecting takes time because the Samsung TV must receive a response from the Soundbar.

(The time required may differ, depending on the Samsung TV model.)

What is the difference between BT READY and BT PAIRING?

• BT READY : In this mode, you can reconnect any Samsung TV or mobile device that was

connected before.

• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR

button on the Soundbar remote control or press and hold the (Source) button on the

bottom of the Soundbar for more than 5 seconds while the Soundbar is in “BT” mode.)

ENG - 20

Notes on Bluetooth connection

• Locate a new device within 1 m to connect via Bluetooth communication.

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• The Soundbar automatically turns off after 18 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following

circumstances:

– If there is a strong electrical eld around the Soundbar.

– If several Bluetooth devices are simultaneously paired with the Soundbar.

– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

Method 2. Connecting via Wi-Fi

Pre-connection Checklist

• Wi-Fi connection is available only on Samsung TV.

• Check whether the wireless router (Wi-Fi) is turned on and the TV is connected to the router.

• The TV and Soundbar must be connected to the same wireless network (Wi-Fi).

• If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi

connection between the TV and Soundbar. Contact your Internet service provider for details.

• Because the menus may differ depending on the year of manufacture, refer to your TV manual.

• To connect the TV to the Soundbar via Wi-Fi, connect the Soundbar to the wireless router rst.

See page 25 for details on how to establish a Wi-Fi connection.

1. For more information about Wi-Fi connection to the Soundbar, see page 25, “Method 2.

Connecting via Wi-Fi (Wireless Network)”.

2. Change the input source of the TV by using the Audio menu to Soundbar.

• Samsung TVs released in 2017 or later

Home ( )  Settings ( )  Sound  Sound Output  [AV] Samsung Soundbar LST70T

(Wi-Fi)

La page charge ...

Samsung HW-LST70T Manuel utilisateur

Samsung HW-LST70T Manuel utilisateur

dans d''autres langues

Documents connexes