Black & Decker LCS1240B Manuel utilisateur
- Catégorie
- Tronçonneuses électriques
- Taper
- Manuel utilisateur
20V MAX*, 40V MAX**
CORDLESS CHAIN SAW
Thank you for choosing BLACK+DECKER!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON.
If you have a question or experience a problem with your BLACK+DECKER
purchase, go to http://www.blackanddecker.com/instantanswers
If you can’t find the answer or do not have access to the Internet, call 1-800-544-
6986 from 8 a.m. to 5 p.m. EST Mon. - Fri. to speak with an agent. Please have the
catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPANOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
To register your new product, visit
www.BlackandDecker.com/NewOwner
KEY INFORMATION YOU SHOULD KNOW:
READ INSTRUCTIONS THOROUGHLY
BEFORE OPERATING!
• DO NOT OVER-TENSION CHAIN. Refer to “Adjusting Chain
Tension” for proper method of tensioning chain.
• Retighten chain frequently during first two hours of use.
INSTRUCTION MANUAL
CATALOG NUMBER
LCS1020 (20V MAX*)
CATALOG NUMBER
LCS1240 (40V MAX**)
*Maximum initial battery pack voltage (measured without
a workload) is 20 volts. The nominal voltage is 18.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING:
Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence
of flammable liquids, gases or dust.
Power tools create sparks which may
ignite the dust or fumes.
c) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the
outlet. Never modify the plug in
any way. Do not use any adapter
plugs with earthed (grounded)
power tools. Unmodified plugs and
matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or
grounded.
c) Do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged or
entangled cords increase the risk of
electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a
ground fault circuit interrupter
(GFCI) protected supply. Use of
a GFCI reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence of
drugs, alcohol or medication. A
moment of inattention while operating
power tools may result in serious
personal injury.
b) Use personal protective equipment.
Always wear eye protection.
Protective equipment such as dust
mask, nonskid safety shoes, hard
hat, or hearing protection used for
appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting.
Ensure the switch is in the off
position before connecting to
power source and/ or battery pack,
picking up or carrying the tool.
Carrying power tools with your finger
on the switch or energizing power
tools that have the switch on invites
accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry
or long hair can be caught in moving
parts.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially haz ard ous situation which, if not avoided,
may result in minor or mod er ate injury.
NOTICE: Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
3
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, changing
accessories, or storing power
tools. Such preventive safety
measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories
and tool bits, etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations
different from those intended could
result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack.
b) Use power tools only with
specifically designated battery
packs. Use of any other battery packs
may create a risk of injury and fire.
c) When battery pack is not in use,
keep it away from other metal
objects like paper clips, coins,
keys, nails, screws, or other small
metal objects that can make a
connection from one terminal
to another. Shorting the battery
terminals together may cause burns
or a fire.
d) Under abusive conditions, liquid
may be ejected from the battery,
avoid contact. If contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This
will ensure at the safety of the power
tool is maintained.
READ ALL INSTRUCTIONS
CHAIN SAW SAFETY
WARNINGS:
• Keep all parts of the body away from
the saw chain when the chain saw is
operating. Before you start the chain
saw, make sure the saw chain is not
contacting anything. A moment of
inattention while operating chain saws
may cause entanglement of your clothing
or body with the saw chain.
• Always hold the chain saw with your
right hand on the rear handle and
your left hand on the front handle.
Holding the chain saw with a reversed
hand configuration increases the risk of
personal injury and should never be done.
• Hold the power tool by insulated
gripping surfaces only, because the
saw chain may contact hidden wiring.
Saw chains contacting a “live” wire may
make exposed metal parts of the power
tool “live” and could give the operator an
electric shock.
• Wear safety glasses and hearing
protection. Further protective
equipment for head, hands, legs
and feet is recommended. Adequate
protective clothing will reduce personal
injury by flying debris or accidental
contact with the saw chain.
• Do not operate a chain saw in a tree.
Operation of a chain saw while up in a
tree may result in personal injury.
• Always keep proper footing and
operate the chain saw only when
standing on fixed, secure and level
surface. Slippery or unstable surfaces
such as ladders may cause a loss of
balance or control of the chain saw.
• When cutting a limb that is under
tension be alert for spring back. When
the tension in the wood fibers is released
the spring loaded limb may strike the
operator and/or throw the chain saw out
of control.
• Use extreme caution when cutting
brush and saplings. The slender material
may catch the saw chain and be whipped
toward you or pull you off balance.
• Carry the chain saw by the front
handle with the chain saw switched
off and away from your body. When
transporting or storing the chain
saw always fit the scabbard. Proper
handling of the chain saw will reduce the
likelihood of accidental contact with the
moving saw chain.
• Follow instructions for lubricating,
chain tensioning and changing
accessories. Improperly tensioned or
lubricated chain may either break or
increase the chance for kickback.
• Keep handles dry, clean, and free from
oil and grease. Greasy, oily handles are
slippery causing loss of control.
• Cut wood only. Do not use chain
saw for purposes not intended. For
example: do not use chain saw for
cutting plastic, masonry or non-wood
building materials. Use of the chain
saw for operations different than intended
could result in a hazardous situation.
CAUSES AND OPERATOR
PREVENTION OF KICKBACK:
Kickback may occur when the nose or
tip of the guide bar touches an object, or
when the wood closes in and pinches the
saw chain in the cut.
Tip contact in some cases may cause a
sudden reverse reaction, kicking the guide
bar up and back towards the operator.
Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back towards the operator.
Either of these reactions may cause you
to lose control of the saw which could
result in serious personal injury. Do not
rely exclusively upon the safety devices
built into your saw. As a chain saw user,
you should take several steps to keep your
cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/
or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below:
• Maintain a firm grip, with thumbs
and fingers encircling the chain saw
handles, with both hands on the saw
and position your body and arm to
allow you to resist kickback forces.
Kickback forces can be controlled by the
operator, if proper precautions are taken.
Do not let go of the chain saw.
• Do not overreach and do not cut above
chest height. This helps prevent unintended
tip contact and enables better control of the
chain saw in unexpected situations.
• Only use replacement bars and chains
specified by the manufacturer. Incorrect
replacement bars and chains may cause
chain breakage and/or kickback.
• Follow the manufacturer’s sharpening
and maintenance instructions for the
saw chain. Decreasing the depth gauge
height can lead to increased kickback.
THE FOLLOWING PRECAUTIONS
SHOULD BE FOLLOWED TO
MINIMIZE KICKBACK:
(1.) Grip Saw Firmly. Hold the chain saw
firmly with both hands when the motor is
running. Use a firm grip with thumbs and
fingers encircling the chain saw handles.
Chain saw will pull forward when cutting
on the bottom edge of the bar, and push
backward when cutting along the top edge of
the bar.
(2.) Do not over reach.
(3.) Keep proper footing and balance at all
times.
(4.) Don’t let the nose of the guide bar
contact a log, branch, ground or other
obstruction.
(5.) Don’t cut above shoulder height.
(6.) Use devices such as low kickback
chain and reduced kickback guide bars
that reduce the risks associated with
kickback.
(7.) Only use replacement bars and chains
specified by the manufacturer or the
equivalent.
(8.) Never let the moving chain contact any
object at the tip of the guide bar.
(9.) Keep the working area free from
obstructions such as other trees, branches,
rocks, fences, stumps, etc. Eliminate or
avoid any obstruction that your saw chain
could hit while you are cutting through a
particular log or branch.
(10.) Keep your saw chain sharp and
properly tensioned. A loose or dull chain
can increase the chance of kickback.
Check tension at regular intervals with the
motor stopped and tool unplugged, never
with the motor running.
(11.) Begin and continue cutting only with
the chain moving at full speed. If the chain
is moving at a slower speed, there is a
greater chance for kickback to occur.
(12.) Cut one log at a time.
(13.) Use extreme caution when re-entering
a previous cut. Engage ribbed bumpers
into wood and allow chain to reach full
speed before proceeding with cut.
(14.) Do not attempt plunge cuts or bore
cuts.
(15.) Watch for shifting logs or other forces
that could close a cut and pinch or fall into
chain.
KICKBACK SAFETY FEATURES
WARNING: The following features
are included on your saw to help reduce
the hazard of kickback; however such
features will not totally eliminate this
4
5
dangerous reaction. As a chain saw user
do not rely only on safety devices. You must
follow all safety precautions, instructions,
and maintenance in this manual to help
avoid kickback and other forces which can
result in serious injury.
•Reduced-Kickback Guide Bar,
designed with a small radius tip which
reduces the size of the kickback danger
zone on bar tip. A reduced - kickback
guide bar is one which has been
demonstrated to significantly reduce the
number and seriousness of kickbacks
when tested in accordance with safety
requirements for electric chain saws.
•Low-Kickback Chain, designed with a
contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter. A
low-kickback chain is a chain which has
met kickback performance requirements
of ANSI B175.1-2012.
•Do not operate chain saw while in
a tree, on a ladder, on a scaffold, or
from any unstable surface.
•Hold tool by insulated gripping
surfaces when performing an
operation where the cutting tool may
contact hidden wiring. Contact with a
“live” wire will make exposed metal parts
of the tool “live” and shock the operator.
•Do not attempt operations beyond
your capacity or experience. Read
thoroughly and understand completely
all instructions in this manual.
•Before you start chain saw, make sure
saw chain is not contacting any object.
•Do not operate a chain saw with one
hand! Serious injury to the operator,
helpers, or bystanders may result
from one handed operation. A chain
saw is intended for two-handed use only.
•Keep the handles dry, clean, and free
of oil or grease.
• Do not allow dirt, debris, or sawdust to
build up on the motor or outside air vents.
• Stop the chain saw before setting it down.
• Do not cut vines and/or small under brush.
•Use extreme caution when cutting
small size brush and saplings because
slender material may catch the saw
chain and be whipped toward you or pull
you off balance.
WARNING: Some dust created by
power sanding, sawing, grinding, drilling,
and other construction activities contains
chemicals known to the State of California
to cause cancer, birth defects or other
reproductive harm. Some examples of
these chemicals are:
•leadfromlead-basedpaints,
•
crystalline silica from bricks and
cement and other masonry products,
and
•arsenicandchromiumfrom
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are
specially designed to filter out microscopic
particles.
•Avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into
your mouth, eyes, or lay on the skin
may promote absorption of harmful
chemicals.
WARNING: Use of this tool can
generate and/or disburse dust, which
may cause serious and permanent
respiratory or other injury. Always use
NIOSH/OSHA approved respiratory
protection appropriate for the dust
exposure. Direct particles away from face
and body.
CHAIN SAW NAMES AND TERMS
• Bucking - The process of cross cutting a
felled tree or log into lengths.
• Motor Brake - A device used to stop the
saw chain when the trigger is released.
• Chain Saw Powerhead - A chain saw
without the saw chain and guide bar.
• Drive Sprocket or Sprocket - The
toothed part that drives the saw chain.
•
Felling - The process of cutting down a
tree.
• Felling Back Cut - The final cut in a tree
felling operation made on the opposite side
of the tree from the notching cut.
• Front Handle - The support handle located
at or toward the front of the chain saw.
• Front Hand Guard - A structural barrier
between the front handle of a chain saw
and the guide bar, typically located close
to the hand position on the front handle.
• Guide Bar - A solid railed structure that
supports and guides the saw chain.
• Guide Bar Scabbard - Enclosure fitted
over guide bar to prevent tooth contact
when saw is not in use.
• Kickback - The backward or upward
motion, or both of the guide bar
occurring when the saw chain near the
nose of the top area of the guide bar
contacts any object such as a log or
branch, or when the wood closes in and
pinches the saw chain in the cut.
•
Kickback, Pinch - The rapid pushback of
the saw which can occur when the wood
closes in and pinches the moving saw
chain in the cut along the top of the guide
bar.
• Kickback, Rotational - The rapid
upward and backward motion of the saw
which can occur when the moving saw
chain near the upper portion of the tip of
the guide bar contacts an object, such as
6
a log or branch.
• Limbing - Removing the branches from a
fallen tree
• Low-Kickback Chain - A chain that
complies with the kickback
performance requirements of ANSI
B175.1-2012 (when tested on
a representative sample of chain saws.)
• Normal Cutting Position - Those
positions assumed in
performing the bucking and felling cuts.
• Notching Undercut - A notch cut in a
tree that directs the tree’s fall.
• Rear Handle - The support handle
located at or toward the rear of the saw.
• Reduced Kickback Guide Bar - A guide
bar which has been demonstrated to
reduce kickback significantly.
• Replacement Saw Chain - A chain that
complies with kickback performance
requirements of ANSI B175.1-2000 when
tested with specific chain saws. It may
not meet the ANSI performance
requirements when used with other saws.
• Saw Chain - A loop of chain having
cutting teeth, that cut the wood,and that
is driven by the motor and is supported
by the guide bar.
• Ribbed Bumper - The ribs used when
felling or bucking to pivot the saw and
maintain position while sawing.
• Switch - A device that when operated
will complete or interrupt an electrical
power circuit to the motor of the chain
saw.
• Switch Linkage - The mechanism that
transmits motion from a trigger to the
switch.
• Switch Lockout - A movable stop that
prevents the unintentional operation of
the switch until manually actuated.
INTENDED USE
Your BLACK+DECKER Chain Saw is ideal
for pruning applications and cutting small
logs up to 10 inches (254 mm) for the
LCS1020 and up to 12 inches (305 mm)
for the LCS1240 in diameter. This tool is
intended for consumer use only.
SAVE THESE INSTRUCTIONS
SYMBOLS
The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V ..................volts
A ..................amperes
Hz ................hertz
W .................watts
min ..............minutes
or AC ...... alternating current
or DC ...direct current
n
o ................no load speed
................Class I Construction
(grounded)
................earthing terminal
................safety alert symbol
................Class II Construction
(double insulated)
.../min or rpm...revolutions or
reciprocation per minute
m/s ..............meters per second
in .................inches
mm ..............millimeters
...............Read instruction manual
before use
................Use proper respiratory
protection
................ Use proper eye protection
................Use proper hearing
protection
..............Rotational direction of the
saw chain
...............
Contact of the guide bar tip with
any object should be avoided
................
Tip contact can cause the guide
bar to move suddenly upward and
backward, which can cause
serious injury
...........Always use two hands when
operating the chain saw
IMPORTANT SAFETY
INSTRUCTIONS FOR BATTERY
CHARGERS
SAVE THESE INSTRUCTIONS: THIS
MANUAL CONTAINS IMPORTANT
SAFETY INSTRUCTIONS FOR
BATTERY CHARGERS.
•Beforeusingcharger,readallinstructions
and cautionary markings on charger,
battery pack, and product using battery
pack.
WARNING: SHOCK HAZARD. Do
not allow any liquid to get inside charger.
WARNING: BURN HAZARD. To
reduce the risk of injury, charge only
designated BLACK+DECKER batteries.
Other types of batteries may burst causing
personal injury and damage.
CAUTION: Under certain
conditions, with the charger plugged in to
the power supply, the charger can be
shorted by foreign material. Foreign
materials of a conductive nature such as,
but not limited to, steel wool, aluminum foil,
or any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the power
supply when there is no battery pack in the
cavity. Unplug charger before attempting
to clean.
WARNING:
The charger supplied
with this product is intended to be plugged
in such that it is correctly orientated in a
vertical or floor mount position.
•DO NOT attempt to charge the battery
pack with any chargers other than the
ones in this manual. The charger and
7
battery pack are specifically designed to
work together.
•These chargers are not intended
for any uses other than charging
designated Black+Decker rechargeable
batteries. Any other uses may result in
risk of fire, electric shock or electrocution.
•Do not expose charger to rain or snow.
•Pull by plug rather than cord when
disconnecting charger. This will reduce
risk of damage to electric plug and cord.
•Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
•Do not use an extension cord unless
it is absolutely necessary. Use of
improper extension cord could result in
risk of fire, electric shock, or electrocution.
•An extension cord must have adequate
wire size (AWG or American Wire
Gauge) for safety. The smaller the gauge
number of the wire, the greater the capacity
of the cable, that is 16 gauge has more
capacity than 18 gauge. When using more
than one extension to make up the total
length, be sure each individual extension
contains at least the minimum wire size.
Recommended Minimum Wire Size for
Extension Cords
•Do not place any object on top of
charger or place the charger on a soft
surface that might block the ventilation
slots and result in excessive internal
heat. Place the charger in a position
away from any heat source. The charger
is ventilated through slots in the top and
the bottom of the housing.
•Do not mount charger on wall or
permanently affix charger to any
surface. The charger is intended to use
on a flat, stable surface (i.e., table top,
bench top).
•Do not operate charger with damaged
cord or plug — have them replaced
immediately.
•Do not operate charger if it has
received a sharp blow, been dropped,
or otherwise damaged in any way. Take
it to an authorized service center.
•Do not disassemble charger; take it to
an authorized service center when service
or repair is required. Incorrect reassembly
may result in a risk of electric shock,
electrocution or fire.
•Disconnect the charger from the outlet
before attempting any cleaning. This
will reduce the risk of electric shock.
Removing the battery pack will not reduce
this risk.
•NEVER attempt to connect 2 chargers
together.
•The charger is designed to operate on
standard household electrical power
(120 Volts). Do not attempt to use it on
any other voltage.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY WARNINGS
FOR BATTERY PACKS
WARNING:
For safe operation, read
this manual and manuals originally supplied
with tool before using the charger.
The battery pack is not fully charged out of
the carton. Before using the battery pack and
charger, read the safety instructions below.
Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
•Do not incinerate the battery pack even
if it is severely damaged or is completely
worn out. The battery pack can explode in a
fire. Toxic fumes and materials are created
when battery packs are burned.
•Do not charge or use battery in
explosive atmospheres, such as in the
presence of flammable liquids, gases or
dust. Inserting or removing the battery from
the charger may ignite the dust or fumes.
•If battery contents come into contact
with the skin, immediately wash area
with mild soap and water. If battery liquid
gets into the eye, rinse water over the
open eye for 15 minutes or until irritation
ceases. If medical attention is needed,
the battery electrolyte for Li-ion batteries
is composed of a mixture of liquid organic
carbonates and lithium salts.
•Contents of opened battery cells may
cause respiratory irritation. Provide
fresh air. If symptoms persist, seek
medical attention.
WARNING:
BURN HAZARD.
BATTERY LIQUID MAY BE FLAMMABLE
IF EXPOSED TO SPARK OR FLAME.
•Charge the battery packs only in
Black+ Decker chargers.
•DO NOT splash or immerse in water or
other liquids. This may cause premature
cell failure.
•Do not store or use the tool and
battery pack in locations where the
temperature may reach or exceed
105°F (40˚C) (such as outside sheds or
metal buildings in summer).
WARNING:
Never attempt to open
the battery pack for any reason. If
battery pack case is cracked or
damaged, do not insert into charger. Do
Minimum Gauge for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V 0-50 51-100 101-200 201-300
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
More Not more American Wire Gauge
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
8
not crush, drop or damage battery pack.
Do not use a battery pack or charger that
has received a sharp blow, been dropped,
run over or damaged in any way (i.e.,
pierced with a nail, hit with a hammer,
stepped on). Damaged battery packs
should be returned to service center for
recycling.
WARNING:
Fire hazard. Do not
store or carry battery so that metal
objects can contact exposed battery
terminals. For example, do not place
battery in aprons, pockets, tool boxes,
product kit boxes, drawers, etc., with loose
nails, screws, keys, etc. Transporting
batteries can possibly cause fires if the
battery terminals inadvertently come in
contact with conductive materials such
as keys, coins, hand tools and the like.
The US Department of Transportation
Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in
commerce or on airplanes (i.e., packed in
suitcases and carry-on luggage) UNLESS
they are properly protected from short
circuits. So when transporting individual
batteries, make sure that the battery
terminals are protected and well insulated
from materials that could contact them and
cause a short circuit. NOTE: LI-ION
batteries should not be put in checked
baggage.
STORAGE
RECOMMENDATIONS
1. The best storage place is one that is
cool and dry away from direct sunlight and
excess heat or cold.
2. Long-term storage will not harm the
battery pack or charger, unless the battery
is depleted.
CHARGING PROCEDURE
The standard charger provided will charge
a fully depleted battery in about 4-5 hours.
1. Plug the charger into an appropriate
outlet before inserting the battery pack.
2. Insert the battery pack into the charger.
3. The green LED will flash indicating that
the battery is being charged.
4. The completion of charge is indicated
by the green LED remaining on
continuously. The pack is fully charged
and may be used at this time or left on the
charger.
Recharge discharged batteries as soon as
possible after use or battery life may be
greatly diminished. It is recommended that
the batteries be recharged after each use.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can
be obtained if the battery pack is charged
when the air temperature is between 60°F
and 80°F (16°- 27°C). DO NOT charge
the battery pack in an air temperature
below +40°F (+4.5°C), or above +105°F
(+40.5°C). This is important and will
prevent serious damage to the battery
pack.
2. The charger and battery pack may
become warm to touch while charging.
This is a normal condition, and does not
indicate a problem. To facilitate the cooling
of the battery pack after use, avoid placing
the charger or battery pack in a warm
environment such as in a metal shed, or an
uninsulated trailer.
3. If the battery pack does not charge
properly:
a. Check current at receptacle by
plugging in a lamp or other appliance
b. Check to see if receptacle is
connected to a light switch which turns
power off when you turn out the lights.
c. Move charger and battery pack to
a location where the surrounding air
temperature is approximately 60°F and
80°F (16°- 27°C)
d. If charging problems persist, take the
tool, battery pack and charger to your
local service center.
4. The battery pack should be recharged
when it fails to produce sufficient power
on jobs which were easily done previously.
DO NOT CONTINUE to use under these
conditions. Follow the charging procedure.
You may also charge a partially used pack
whenever you desire with no adverse
affect on the battery pack.
5. Foreign materials of a conductive
nature such as, but not limited to, steel
wool, aluminum foil, or any buildup of
metallic particles should be kept away
from charger cavities. Always unplug the
charger from the power supply when there
is no battery pack in the cavity. Unplug
charger before attempting to clean.
6. Do not freeze or immerse charger in
water or any other liquid.
WARNING:
SHOCK HAZARD. Do
not allow any liquid to get inside charger.
Never attempt to open the battery pack
for any reason. If the plastic housing of
the battery pack breaks or cracks, return
to a service center for recycling.
9
1. Trigger switch
2. Lock-off button
3. Front hand guard
4. Guide bar
5. Saw chain
6. Sprocket cover
7. Bar adjust locking knob
8. Chain tensioning knob
9. Guide bar scabbard
10. Rear handle
11. Front handle
12. 20V Battery (not shown)
13. 40V Battery (not shown)
14. Oil cap
15. Oil primer bulb
16. Oil level indicator
1
3
6
7
4
2
5
9
11
10
14
8
16
1
3
6
7 4
2
5
9
11
10
14
8
16
LCS1020
LCS1240
FUNCTIONAL DESCRIPTION
15
20V MAX* BLACK+DECKER Battery and Charger Systems
Chargers/Charge Time*** (Hours) (0% to 100% charge)
20V MAX*
Batteries
Watt
Hours
20V MAX* Chargers
LCS200 LCS1620 LCS201 LCS202 L2AFC L2AFCBST
LBX20 26
6.5 3.25 1.3 0.65 0.65 0.65
LBXR20 30
7.5 3.75 1.5 0.75 0.75 0.75
LBXR2020 40
10 5 2 1 1 1
LBXR2520 50
12.5 6.25 2.5 1.25 1.25 1.25
LB2X3020 60
15 7.5 3 1.5 1.5 1.5
LB2X4020 80
20 10 4 2 2 2
40V MAX** BLACK+DECKER Battery and Charger Systems
Chargers/Charge Time*** (Hours) (0% - 100% charge)
40V MAX**
Batteries
Watt Hours
40V MAX** Chargers
LCS36 LCS40 LCS436
LBX36 47
1 1 3.25
LBXR36 60
1.25 1.25 3.75
LBX1540 60
1.25 1.25 3.75
LBXR2036 80
1.5 1.5 5
LBX2040 80
1.5 1.5 5
LBXR2540 100
1.75 1.75 6.25
LBX2540 100
1.75 1.75 6.25
***All charge times are approximate. Actual charge time may vary.
10
•Placethesawonafirmsurface.
•Rotatethebaradjustlockingknob(7)
counterclockwise as shown in Figure B
to remove sprocket cover (6).
•Wearingprotectivegloves,graspthesaw
chain (5) and wrap it around the guide
bar (4), ensuring the teeth are facing the
correct direction (see figure F)
•Ensurethechainisproperlysetintheslot
around the entire guide bar.
•Placethesawchainaroundthesprocket
(17) while lining up the slot on the guide
bar with the bolt (18) in the base of the
tool as shown in Figure C.
•Thetensioningknobmustberotated
counterclockwise to its stop. Arrows on
the sprocket cover and tensioning knob
must align before the cover is replaced.
Once in place, hold the bar still, replace
sprocket cover (6).
Make sure tool-free
tension assembly bolt hole on the cover
lines up with the bolt (18) in the main
housing as shown in Figure D. Rotate
the bar adjust locking knob (7) clockwise
until snug, then loosen knob one full
turn, so the saw chain can be properly
tensioned.
Note:
If the cover does not fit correctly,
check that the tab for the tool free tensioner
on the bar aligns with the slot on the inside
of the sprocket cover.
•Whileholdingthebaradjustlocking
knob (7), rotate the chain tensioning
knob (8) clockwise to increase tension as
shown in Figure E. Make sure the saw
chain (5) is snug around the guide bar
(4).
INSTALLING / REMOVING
BATTERY PACK
WARNING:
Make certain the lock-off
button is engaged to prevent switch actuation
before removing or installing battery.
TO INSTALL BATTERY PACK: Insert
battery pack into tool until an audible click
is heard, as shown in Figure A. Ensure
battery pack is fully seated and fully
latched into position.
TO REMOVE BATTERY PACK:
Depress the battery release button in the
back of the battery pack and pull battery
pack out of tool (figure A).
PREPARING YOUR CHAIN
SAW FOR USE
WARNING:
Read and understand
all instructions.
Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious personal injury.
ASSEMBLY
INSTALLING THE GUIDE BAR AND SAW CHAIN
CAUTION:
Sharp chain. Always
wear protective gloves when handling
the chain. The chain is sharp and can cut
you when it is not running.
WARNING:
Sharp moving chain.
To prevent accidental operation, ensure
that battery is removed from the tool
before performing the following
operations. Failure to do this could result
in serious personal injury.
The saw chain (5) and guide bar (4) are
packed separately in the carton. The chain
has to be attached to the bar, and both
must be attached to the body of the tool.
C
17
18
B
D
A
11
ADJUSTING CHAIN TENSION
CAUTION:
Sharp chain. Always
wear protective gloves when handling
the chain. The chain is sharp and can cut
you when it is not running.
WARNING:
Sharp moving chain. To
prevent accidental operation, ensure that
battery is removed from the tool before
performing the following operations. Failure
to do this could result in serious personal injury.
•Withthesawonafirmsurface,check
the saw chain (5) tension. The tension is
correct when the chain snaps back after
being pulled 1/8 inch (3mm) away from
the guide bar (4) with light force from
the middle finger and thumb as shown
in figure F. There should be no “sag”
between the guide bar and the chain on
the underside as shown in figure G.
•Toadjustsawchaintension,loosenbar
adjust locking knob (7) one full turn and
follow instructions for “Installing the Guide
Bar and Saw Chain.”
•Donotover-tensionthechainasthiswill
lead to excessive wear and will reduce
the life of the bar and chain.
•Oncechaintensioniscorrect,securely
tighten bar adjust locking knob.
•Whenthechainisnew,checkthetension
frequently (after removing battery) during
the first 2 hours of use as a new chain
stretches slightly.
REPLACING THE SAW CHAIN
CAUTION:
Sharp chain. Always
wear protective gloves when handling
the chain. The chain is sharp and can cut
you when it is not running.
WARNING:
S
harp moving chain.
To prevent accidental operation, ensure
that battery is removed from the tool
before performing the following
operations. Failure to do this could result in
serious personal injury.
• Rotatethebaradjustlockingknob(7)
counterclockwise to release chain tension.
•Removesprocketcover(6)asdescribed
in “Installing the Guide Bar and Saw
Chain” section.
•Liftthewornsawchain(5)outofthe
groove in the guide bar (4).
•Placethenewchainintheslotofthe
guide bar, making sure the saw teeth are
facing the correct direction by matching
the arrow on the chain with the graphic on
the sprocket cover (6) shown in figure H.
•Followinstructionsfor“Installingthe
Guide Bar and Saw Chain.”
Replacement chain and bar are available from
your nearest Black+Decker service center.
•LCS1020requiresreplacementchain#
RC1000, service part number 90609782.
Replacement 10” bar, service part
number 90609787.
•LCS1240requiresreplacementchain#
RC1200, service part number 90609781.
Replacement 12” bar, service part
number 90609786.
E
F
G
H
12
• Do not overreach. Do not cut above
chest height. Make sure your footing
is firm. Keep feet apart. Divide your
weight evenly on both feet.
• Use a firm grip with your left hand on
the front handle (11) and your right
hand on the rear handle (10) so that
your body is to the left of the guide bar.
• Do not hold chain saw by front hand
guard (3). Keep elbow of left arm locked
so that left arm is straight to withstand a
kickback.
WARNING: Never use a cross-
handed grip (left hand on the rear handle
and right hand on the front handle).
WARNING: Never allow any part
of your body to be in line with the guide
bar (4) when operating the chain saw.
• Never operate while in a tree, in any
awkward position or on a ladder or
other unstable surface. You may lose
control of saw causing severe injury.
• Keep the chain saw running at full
speed the entire time you are cutting.
• Allow the chain to cut for you. Exert
only light pressure. Do not put pressure
on chain saw at end of cut.
ON / OFF
• Alwaysbesureofyourfootingandgripthe
chain saw firmly with both hands with the
thumb and fingers encircling both handles.
•
To turn the tool ON, depress the lock off
button (2) and squeeze the trigger switch
(1) as shown in figure J. (Once the tool is
running you can release the lock off button.)
•ToturnthetoolOFF,releasethetriggerswitch.
COMMON CUTTING
TECHNIQUES
FELLING
The process of cutting down a tree. Be
sure battery is fully charged before felling
a tree so you can finish on a single charge.
Do not fell trees in high wind conditions.
WARNING: Felling can result in
injury. It should only be performed by a
trained person.
•(Figure K) A retreat path should be
planned and cleared as necessary
SAW CHAIN AND GUIDE BAR OILING
MANUAL OILING SYSTEM (20V ONLY)
This chain saw is equipped with a manual
oiling system that keeps the saw chain
and guide bar lubricated. Slowly press the
primer bulb (15) on the oil cap (14) three
times before making each cut. Hold the
primer bulb down for 1 second each time.
The oil level indicator (16) shows the level
of the oil in the chain saw. If the oil level is
less than a quarter full, remove the battery
from the chain saw and refill with the
correct type of oil.
AUTO OILING SYSTEM (40V ONLY)
This chain saw is equipped with an auto
oiling system that keeps the saw chain and
guide bar constantly lubricated. The oil
level indicator (16) shows the level of the
oil in the chain saw. If the oil level is less
than a quarter full, remove the battery from
the chain saw and refill with the correct
type of oil.
NOTE:
Use a high quality bar and chain
oil for proper chain and bar lubrication. As
a temporary substitute, a non-detergent
SAE30 weight motor oil can be used. The
use of a vegetable based bar and chain
oil is recommended when pruning trees.
Mineral oil is not recommended because it
may harm trees. Never use waste oil or very
thick oil. These may damage your chain saw.
FILLING THE OIL RESERVOIR
•Removetheoilcap(14)andfillthe
reservoir with the recommended chain oil
until the oil level has reached the top of
the oil level indicator (16).
•Refittheoilcap.
•Periodicallyswitchthechainsawoffand
check the oil level indicator to ensure the
bar and chain are being properly oiled.
TRANSPORTING SAW
•Alwaysremovethebatteryfromthetool
and cover the guide bar (4) with the
scabbard (9) (figure I) when transporting
the saw.
OPERATING THE CHAIN SAW
WARNING:
Read and understand
all instructions. Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious personal injury.
• Guard Against Kickback which can
result in severe injury or death. See
Important Safety Instructions “Guard
Against Kickback”, to avoid the risk of
kickback.
J
2
I
13
LIMBING
Re
moving the branches from a fallen tree.
When limbing, leave larger lower limbs to
support the log off the ground. Remove
the small limbs in one cut. Branches under
tension should be cut from the bottom of
the branch towards the top to avoid binding
the chain saw as shown in figure M.
Trim limbs from opposite side keeping
tree stem between you and saw. Never
make cuts with saw between your legs or
straddle the limb to be cut.
BUCKING
WARNING: Recommend that first
time users should practice cutting on a
saw horse.
Cutting a felled tree or log into lengths.
How you should cut depends on how the
log is supported. Use a saw horse
(figure N) whenever possible. Always start
a cut with the chain running at full speed.
•Placethebottomspike(19)ofthechain
saw behind the area of the initial cut as
shown in figure O.
•Turnthechainsawonthenrotatethe
chain and bar down into the tree, using
the spike as a hinge.
•Oncethechainsawgetstoa45degree
angle, level the chain saw again and
repeat steps until you cut fully through.
•When the tree is supported along its
entire length, make a cut from the top
(overbuck), but avoid cutting the earth as
this will dull your saw quickly.
• Figure P- When supported at one end
First, cut 1/3 the diameter from the underside
(underbuck). Then make the finished cut by
overbucking to meet the first cut.
• Figure Q- When supported at both ends
First, cut 1/3 down from the top overbuck.
Then make the finished cut by underbucking
the lower 2/3 to meet the first cut.
•When on a slope
Always stand on the uphill side of the
log. When “cutting through”, to maintain
complete control release the cutting
pressure near the end of the cut without
relaxing your grip on the chain saw
handles. Don’t let the chain contact the
ground. After completing the cut, wait for
the saw chain to stop before you move
the chain saw. Always stop the motor
before moving from cut to cut.
before cuts are started. The retreat path
should extend back and diagonally to
the rear of the expected line of fall.
•Before felling is started, consider the
natural lean of the tree, the location of
larger branches and the wind direction
to judge which way the tree will fall. Have
wedges (wood, plastic or aluminum)
and a heavy mallet handy.
Remove dirt, stones, loose bark, nails,
staples, and wire from the tree where the
felling cuts are to be made.
• Figure L- Notching Undercut - Make
the notch 1/3 of the diameter of the tree,
perpendicular to the direction of the fall.
Make the lower horizontal notching cut
first. This will help to avoid pinching of
either the saw chain or the guide bar when
the second notch cut is being made.
•(Figure L) Felling Back Cut - Make the
felling back cut at least 2 inches (51mm)
higher than the horizontal notching cut.
Keep the felling back cut parallel to the
horizontal notching cut. Make the felling
back cut so enough wood is left to act
as a hinge. The hinge wood keeps the
tree from twisting and falling in the wrong
direction. Do not cut through the hinge.
•(Figure L) As the felling cut gets close
to the hinge the tree should begin to
fall. If there is any chance that the tree
may not fall in the desired direction or it
may rock back and bind the saw chain,
stop cutting before the felling cut is
complete and use wedges to open the
cut and drop the tree along the desired
line of fall. When the tree begins to fall
remove the chain saw from the cut, stop
the motor, put the chain saw down, then
use the retreat path planned. Be alert for
overhead limbs falling and watch your
footing.
M
2 (5cm)
INCHES
DIRECTION
OF FALL
2 (5cm)
INCHES
HINGE
NOTCH
FELLING BACK
CUT
L
DIRECTION
OF
FALL
RETREAT
45°
TREE
K
14
CARE AND MAINTENANCE
Use only mild soap and damp cloth to clean
the tool. Do not use solvents to clean the
plastic housing of the saw. Never let any
liquid get inside the tool; never immerse
any part of the tool into a liquid.
IMPORTANT: To assure product
SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be
performed by authorized service centers
or other qualified service organizations,
always using identical replacement parts.
Regular maintenance ensures a long
effective life for your chain saw.
CHAIN AND BAR
After every few hours of use, remove the
guide bar and chain and clean thoroughly
using a soft bristle brush. Ensure oiling
hole on bar is clear of debris.
SAW CHAIN SHARPENING
CAUTION: Sharp chain. Always
wear protective gloves when handling
the chain. The chain is sharp and can cut
you when it is not running.
WARNING:
Sharp moving chain.
To prevent accidental operation, ensure
that battery is removed from the tool
before performing the following
operations. Failure to do this could result in
serious personal injury.
NOTE: The cutters will dull immediately if
they touch the ground or a nail while cutting.
To get the best possible performance
from your chain saw it is important to
keep the teeth of the chain sharp. Follow
these helpful tips for proper saw chain
sharpening:
1. For best results use a 4.5mm file and
a file holder or filing guide to sharpen
your chain. This will ensure you always
get the correct sharpening angles.
2. Place the file holder flat on the top
plate and depth gauge of the cutter.
3. (Figure R) Keep the correct top plate
(20) filing angle line of 30° on your file
guide parallel with your chain (file at
60° from chain viewed from above).
4. Sharpen cutters on one side of the
chain first. File from the inside of
each cutter to the outside. Then turn
your saw around and repeat the
processes (2,3,4) for cutters on the
other side of the chain.
NOTE: Use a flat file to file the tops of
the rakers (portion of chain link in front
of the cutter) so they are about .025 inch
(.635 mm) below the tips of the cutters as
shown in Figure S.
5. Figure T- Keep all cutter lengths
equal.
6. If damage is present on the chrome
surface of the top plates or side
plates, file back until such damage
is removed.
CAUTION:
After filing, the cutter will
be sharp, use extra caution during this
process.
NOTE: Each time the chain is
sharpened, it loses some of the low
kickback qualities and extra caution should
be used. It is recommended that a chain
be sharpened no more than four times.
O
19
CUT FROM TOP
(OVERBUCK)
AVOID CUTTING EARTH
Q
2nd CUT UNDERBUCK
(2/3 DIAMETER)
TO MEET 1st CUT
(TO AVOID PINCHING)
1st CUT OVERBUCK
(1/3 DIAMETER)
TO AVOID SPLINTERING
1
1
2
2nd CUT OVERBUCK
(2/3DIAMETER)
TO MEET 1st CUT
(TO AVOID PINCHING)
1st CUT UNDERBUCK
(1/3 DIAMETER)
AVOID SPLINTERING
P
N
15
at the end of their useful life have already
been paid by BLACK+DECKER. In some
areas, it is illegal to place spent nickel
cadmium, nickel metal hydride or lithium-
ion batteries in the trash or municipal solid
waste stream and the Call 2 Recycle®
program provides an environmentally
conscious alternative.
Call 2 Recycle, Inc., in cooperation with
BLACK+DECKER and other battery
users, has established the program in the
United States and Canada to facilitate the
collection of spent nickel cadmium, nickel
metal hydride or lithium-ion batteries. Help
protect our environment and conserve
natural resources by returning the spent
nickel cadmium, nickel metal hydride
or lithium-ion batteries to an authorized
BLACK+DECKER service center or to your
local retailer for recycling. You may also
contact your local recycling center for
information on where to drop off the spent
battery. RBRC® is a registered trademark
of Call 2 Recycle, Inc.
This Class B digital apparatus complies
with Canadian ICES-003.
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept
any interference received, including
interference that may cause undesired
operation.
NOTE: This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
•Reorientorrelocatethereceiving
antenna.
•Increasetheseparationbetweenthe
equipment and receiver.
•Connecttheequipmentintoanoutleton
a circuit different from that to which the
ACCESSORIES
WARNING: The use of accessories
not recommended in this manual may be
hazardous.
Replacement chain and bar are available
from your nearest Black+Decker service
center.
•LCS1020requiresreplacementchain#
RC1000, service part number 90609782.
Replacement 10” bar, service part
number 90609787.
•LCS1240requiresreplacementchain#
RC1200, service part number 90609781.
Replacement 12” bar, service part
number 90609786.
The use of accessories not recommended
in this manual may be hazardous.
SERVICE INFORMATION
All BLACK+DECKER Service Centers
are staffed with trained personnel to
provide customers with efficient and
reliable power tool service. Whether you
need technical advice, repair, or genuine
factory replacement parts, contact the
BLACK+DECKER location nearest you. To
find your local service location, call:
1-800-544-6986, or visit
www.blackanddecker.com
The RBRC
®
Seal
The RBRC® (Rechargeable
Battery Recycling Corp oration)
Seal on the nickel cadmium,
nickel metal hydride or lithium-ionbatteries
(or battery packs) indicates that the costs
to recycle these batteries (or battery packs)
T
60°
R
20
S
.025 in.
.635mm
16
TROUBLESHOOTING
If your Chain Saw does not operate correctly check the following:
Problem Possible Cause Possible Solution
•Toolwillnotstart.
•Unitwillnotcharge.
•Bar/chain
overheated.
•Batterynotinstalled
properly.
•Batterynotcharged.
•Lock-outbuttonnot
actuated.
•Batterynotinsertedinto
charger.
•Chaintootight.
•Lubricationneeded.
•Checkbatteryinstallation.
•Checkbatterycharging
requirements.
•Pushlockoffbutton/actuatetrigger.
•Insertbatteryintochargeruntilgreen
LED appears. Charge up to 5 hours
if battery totally drained.
•Referto“adjustingchain
tension” section.
•Referto“chainoiling”section.
•Chainisloose.
•Poorcutquality.
•Chaintensionset
incorrectly.
•Chaintensionset
incorrectly.
•Chainneeds
replacement.
•Referto“adjustingchain
tension” section.
•Referto“adjustingchain
tension” section.
Note: Excessive tension leads to
excessive wear and reduction in
life of bar & chain. Lubricate before
each cut. Refer to “replacing the
chain” section.
•Unitrunsbutdoes
not cut.
•Chaininstalled
backwards.
•Refertosectionsforinstallingand
removing chain.
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK+DECKER help line at 1-800-544-
6986.
•Unitstopswhile
cutting.
•Lithiumbatterydepleted.
•Voltagelimitprotection
exceeded.
•Batterytoohot.
•Chargebattery.
•Unitisbeingforced.Restartand
apply less pressure.
•Allowbatterytocoolfor30minutes
before proceeding.
•Unitdoesnotoil. •Oilreservoiremptied.
•Oilingholeonguidebar
clogged.
•Refillreservoir.
•Cleanguidebar,sprocketand
sprocket cover. Refer to “care and
maintenance” section.
17
LIMITED WARRANTY
TWO-YEAR (LCS1020 ONLY)
THREE-YEAR (LCS1240 ONLY)
Black+Decker (U.S.) Inc. warranties this
product to be free from defects in material
or workmanship for a period of two (2)
years for LCS1020 and three (3) years for
LCS1240 following the date of purchase,
provided that the product is used in a home
environment. This limited warranty does
not cover failures due to abuse, accidental
damage or when repairs have been
made or attempted by anyone other than
Black+Decker and its Authorized Service
Centers. A defective product meeting the
warranty conditions set forth herein will be
replaced or repaired at no charge in either
of two ways:
The first, which will result in exchanges
only, is to return the product to the retailer
from whom it was purchased (provided
that the store is a participating retailer).
Returns should be made within the time
period of the retailer’s policy for exchanges.
Proof of purchase may be required. Please
check with the retailer for its specific
return policy regarding time limits for
returns or exchanges. The second option
is to take or send the product (prepaid)
to a Black+Decker owned or authorized
Service Center for repair or replacement at
Black+Decker’s option. Proof of purchase
may be required. Black+Decker owned
and authorized service centers are listed
online at www.blackanddecker.com.
This warranty does not apply to
accessories. This warranty gives you
specific legal rights and you may have
other rights which vary from state to state.
Should you have any questions, contact
the manager of your nearest Black+Decker
Service Center. This product is not intended
for commercial use, and accordingly, such
commercial use of this product will void this
warranty. All other guarentees, express or
implied, are hereby disclaimed.
LATIN AMERICA: This warranty does not
apply to products sold in Latin America.
For products sold in Latin America, check
country specific warranty information
contained in the packaging, call the local
company or see the website for such
information.
receiver is connected.
•Consultthedealeroranexperienced
radio/TV technician for help.
Changes or modifications to this unit
not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.
This Class B digital apparatus complies
with Canadian ICES-003.
Imported by
Black+Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
18
20 V MAX.*, 40 V MAX.**
SCIE À CHAÎNE SANS FIL
MERCI D’AVOIR CHOISI BLACK+DECKER!
ÀLIRE AVANT DE RETOURNER CE PRODUIT POUR
QUELQUE RAISON QUE CE SOIT:
Si des questions ou des problèmes surgissent après l’achat d’un produit
Black+Decker, consulter le site Web www.blackanddecker.com/instantanswers
pour obtenir des réponses instantanément 24 heures par jour. Si la réponse est
introuvable ou en l’absence d’accès à l’Internet, composer le 1 800 544-6986 de 8 h
à 17 h HNE, du lundi au vendredi, pour parler avec un agent. Prière d’avoir le numéro
de catalogue sous la main lors de l’appel.
CONSERVER CE MODE D’EMPLOI POUR UN USAGE ULTÉRIEUR.
MODE D’EMPLOI
Visite www.BlackandDecker.com/NewOwner
para registrar su nuevo producto.
RENSEIGNEMENTS IMPORTANTS
LIRE LES INSTRUCTIONS AVANT D’UTILISER!
• NE PAS SUR TENDRE LA CHAÎNE. Se reporter à la section
« RÉGLAGE DE LA TENSION DE LA CHAÎNE » pour savoir
comment tendre correctement la chaîne.
• Retendre la chaîne fréquemment pendant les deux premières
heures d’utilisation.
NUMERO DE CATALOGUE
LCS1020 (20V MAX*)
NUMERO DE CATALOGUE
LCS1240 (40V MAX**)
**Latensioninitialemaximaledubloc-piles(mesuréesanscharge
detravail)estde40volts.Latensionnominale,mesuréeavecune
chargedetravail,estde36volts.
*Latensioninitialemaximaledubloc-piles(mesuréesanscharge
detravail)estde20volts.Latensionnominale,mesuréeavecune
chargedetravail,estde18volts.
19
Avertissements de sécurité
généraux pour les outils électriques
AVERTISSEMENT : Lire tous
les avertissements de sécurité et
toutes les directives. Le non-respect
des avertissements et des directives
pourrait se solder par un choc
électrique, un incendie et/ou une
blessure grave.
Conserver tous les
avertissements et toutes les
directives pour un usage
ultérieur.
Le terme «outil électrique» cité dans
les avertissements se rapporte à votre
outil électrique à alimentation sur
secteur (avec fil) ou par piles (sans fil).
1) Sécurité du lieu de travail
a) Tenir la zone de travail propre et bien
éclairée. Les endroits sombres sont
souvent des causes d’accidents.
b) Ne pas faire fonctionner d’outils
électriques dans un milieu déflagrant,
vsoit en présence de liquides
inflammables, de gaz ou de poussière.
Les outils électriques produisent des
étincelles qui peuvent enflammer la
poussière ou les vapeurs.
c) Éloigner les enfants et les curieux au
moment d’utiliser un outil électrique.
Une distraction pourrait vous en faire
perdre la maîtrise.
2) Sécurité en matière d’électricité
a) Les fiches des outils électriques
doivent correspondre à la prise. Ne
jamais modifier la fiche en aucune
façon. Ne jamais utiliser de fiche
d’adaptation avec un outil électrique mis
à la terre. Le risque de choc électrique
sera réduit par l’utilisation de fiches non
modifiées correspondant à la prise.
b) Éviter tout contact physique avec des
surfaces mises à la terre comme des
tuyaux, des radiateurs, des cuisinières
et des réfrigérateurs. Le risque de choc
électrique est plus élevé si votre corps est
mis à la terre.
c) Ne pas exposer les outils électriques à
la pluie ou à d’autres conditions où il
pourrait être mouillé. La pénétration de
l’eau dans un outil électrique augmente le
risque de choc électrique.
d) Ne pas utiliser abusivement le cordon
d’alimentation. Ne jamais utiliser
le cordon pour transporter, tirer ou
débrancher un outil électrique. Tenir le
cordon éloigné de la chaleur, de l’huile,
des bords tranchants ou des pièces
mobiles. Les cordons endommagés ou
emmêlés augmentent les risques de choc
électrique.
e) Pour l’utilisation d’un outil électrique
à l’extérieur, se servir d’une rallonge
convenant à une telle utilisation.
L’utilisation d’une rallonge conçue pour
l’extérieur réduit les risques de choc
électrique.
f) S’il est impossible d’éviter l’utilisation
d’un outil électrique dans un endroit
humide, brancher l’outil dans une
prise ou sur un circuit d’alimentation
dotés d’un disjoncteur de fuite à la
terre (GFCI). L’utilisation de ce type de
disjoncteur réduit les risques de choc
électrique.
3) Sécurité personnelle
a) Être vigilant, surveiller le travail
effectué et faire preuve de jugement
lorsqu’un outil électrique est utilisé. Ne
pas utiliser d’outil électrique en cas de
fatigue ou sous l’influence de drogues,
d’alcool ou de médicaments. Un simple
moment d’inattention en utilisant un outil
électrique peut entraîner des blessures
corporelles graves.
b) Utiliser des équipements de protection
individuelle. Toujours porter une
protection oculaire. L’utilisation
d’équipements de protection comme un
masque antipoussière, des chaussures
antidérapantes, un casque de sécurité
ou des protecteurs auditifs lorsque la
LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS
Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il
contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les
symboles ci-dessous servent à vous aider à reconnaître cette information.
DANGER : Indique une situation dangereuse imminente qui, si elle n’est pas
évitée, causera la mort ou des graves blessures.
AVERTISSEMENT : Indique une situation potentiellement dangereuse qui,
si elle n’est pas évitée, pourrait causer la mort ou de graves blessures.
MISE EN GARDE : Indique une situation potentiellement dangereuse qui, si
elle n’est pas évitée, pourrait causer des blessures mineures ou modérées.
MISE EN GARDE : Utilisé sans le symbole d’alerte à la sécurité, indique une
situation potentiellement dangereuse qui, si elle n’est pas évitée, peut résulter en des
dommages à la propriété.
20
situation le requiert réduira les risques de
blessures corporelles.
c) Empêcher les démarrages intempestifs.
S’assurer que l’interrupteur se trouve
à la position d’arrêt avant de relier
l’outil à une source d’alimentation et/
ou d’insérer un bloc-piles, de ramasser
ou de transporter l’outil. Transporter
un outil électrique alors que le doigt
repose sur l’interrupteur ou brancher un
outil électrique dont l’interrupteur est à la
position de marche risque de provoquer
un accident.
d) Retirer toute clé de réglage ou clé
standard avant de démarrer l’outil.
Une clé standard ou une clé de réglage
attachée à une partie pivotante peut
causer des blessures.
e) Ne pas trop tendre les bras. Conserver
son équilibre en tout temps. Cela
permet de mieux maîtriser l’outil
électrique dans les situations imprévues.
f) S’habiller de manière appropriée. Ne
pas porter de vêtements amples ni
de bijoux. Garder les cheveux, les
vêtements et les gants à l’écart des
pièces mobiles. Les vêtements amples,
les bijoux ou les cheveux longs risquent
de rester coincés dans les pièces
mobiles.
g) Si des composants sont fournis
pour le raccordement de dispositifs
de dépoussiérage et de ramassage,
s’assurer que ceux-ci sont bien
raccordés et utilisés. L’utilisation d’un
dispositif de dépoussiérage peut réduire
les dangers
engendrés par les poussières.
4) Utilisation et entretien d’un outil
électrique
a) Ne pas forcer un outil électrique.
Utiliser l’outil électrique approprié à
l’application. L’outil électrique approprié
effectuera un meilleur travail, de façon
plus sûre et à la vitesse pour laquelle il a
été conçu.
b) Ne pas utiliser un outil électrique dont
l’interrupteur est défectueux. Tout
outil électrique dont l’interrupteur est
défectueux est dangereux et doit être
réparé.
c) Débrancher la fiche du secteur ou le
bloc-piles de l’outil électrique avant
de faire tout réglage ou changement
d’accessoire, ou avant de ranger l’outil
électrique. Ces mesures préventives
réduisent les risques de démarrage
accidentel de l’outil électrique.
d) Ranger les outils électriques hors de
la portée des enfants, et ne permettre
à aucune personne n’étant pas
familière avec un outil électrique (ou
son manuel d’instruction) d’utiliser ce
dernier. Les outils électriques deviennent
dangereux entre les mains d’utilisateurs
inexpérimentés.
e) Entretenir les outils électriques.
Vérifier les pièces mobiles pour
s’assurer qu’elles sont bien alignées
et tournent librement, qu’elles sont en
bon état et ne sont affectées par aucun
trouble susceptible de nuire au bon
fonctionnement de l’outil électrique.
En cas de dommage, faire réparer
l’outil électrique avant toute nouvelle
utilisation. Beaucoup d’accidents sont
causés par des outils électriques mal
entretenus.
f) S’assurer que les outils de coupe sont
aiguisés et propres. Les outils de coupe
bien entretenus et affûtés sont moins
susceptibles de se coincer et sont plus
faciles à contrôler.
g) Utiliser l’outil électrique, les
accessoires, les forets, etc.
conformément aux présentes
directives en tenant compte des
conditions de travail et du travail à
effectuer. L’utilisation d’un outil électrique
pour toute opération autre que celle pour
laquelle il a été conçu est dangereuse.
5) Utilisation et entretien du bloc-piles
a) Ne recharger l’outil qu’au moyen du
chargeur précisé par le fabricant.
L’utilisation d’un chargeur qui convient à un
type de bloc-piles risque de provoquer un
incendie s’il est utilisé avec un autre type
de bloc-piles.
b) Utiliser les outils électriques
uniquement avec les blocs-piles
conçus à cet effet. L’utilisation de tout
autre bloc-piles risque de causer des
blessures ou un incendie.
c) Lorsque le bloc-piles n’est pas utilisé,
le tenir éloigné des objets métalliques,
notamment des trombones, de la
monnaie, des clés, des clous, des vis,
etc., qui peuvent établir une connexion
entre les deux bornes. Le court-circuit
des bornes du bloc-piles risque de
provoquer des étincelles, des brûlures ou
un incendie.
d) En cas d’utilisation abusive, le liquide
peut gicler hors du bloc-piles, éviter
tout contact. Si un contact accidentel
se produit, laver à grande eau. Si
le liquide entre en contact avec les
yeux, obtenir des soins médicaux. Le
liquide qui gicle hors du bloc-piles peut
provoquer des irritations ou des brûlures.
6) Réparation
a) Faire réparer l’outil électrique par
un réparateur professionnel en
n’utilisant que des pièces de rechange
identiques. Cela permettra de maintenir
une utilisation sécuritaire de l’outil
électrique.
LIRE TOUTES CES DIRECTIVES.
CONSIGNES DE SÉCURITÉ ET
AVERTISSEMENTS POUR LES
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
Black & Decker LCS1240B Manuel utilisateur
- Catégorie
- Tronçonneuses électriques
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Black & Decker LCS1240B User manual
- español: Black & Decker LCS1240B Manual de usuario
Documents connexes
-
Black & Decker LCS1240B Manuel utilisateur
-
Black & Decker CCS818 Manuel utilisateur
-
-
-
-
-
-
-
-