Whirlpool AKZM 831/IX Mode d'emploi

Catégorie
Fours
Taper
Mode d'emploi
User and maintenance manual
Manuel d’utilisation et d’entretien
Інструкція з експлуатації
і технічного обслуговування
UK
AKZM 831
GB1
YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT
This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
All safety warnings give specific details of the potential risk present and indicate how to reduce risk of
injury, damage and electric shock resulting from improper use of the appliance. Carefully observe the
following instructions:
- The appliance must be disconnected from the power supply before carrying out any installation
work.
- Installation and maintenance must be carried out by a qualified technician, in compliance with the
manufacturers instructions and local safety regulations. Do not repair or replace any part of the
appliance unless specifically stated in the user manual.
- Regulations require that the appliance is earthed.
- The power cable must be long enough for connecting the appliance, once fitted in its housing, to the
power supply socket.
- For installation to comply with current safety regulations, an all-pole disconnect switch with
minimum contact gap of 3 mm must be utilized.
- Do not use multiple plug adapters or extension leads.
- Do not pull the power supply cable in order to unplug the appliance.
- The electrical components must not be accessible to the user after installation.
- Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
- This appliance is designed solely for use as a domestic appliance for cooking food. No other type of
use is permitted (e.g.: heating rooms). The Manufacturer declines all responsibility for inappropriate
use or incorrect setting of the controls.
- The appliance is not intended for use by persons (including children) with any physical, sensory or
mental impairment, or without experience and knowledge of the appliance, unless supervised or
previously instructed in its use by those responsible for their safety.
- The accessible parts of the appliance may become very hot during use. Young children should be
kept away from the appliance and supervised to ensure that they do not play with it.
- During and after use, do not touch the heating elements or interior surfaces of the appliance - risk of
burns. Do not allow the appliance to come into contact with cloths or other flammable materials until
all the components have cooled sufficiently.
- At the end of cooking, exercise caution when opening the appliance door, letting the hot air or steam
exit gradually before accessing the oven. When the appliance door is shut, hot air is vented from the
aperture above the control panel. Do not obstruct the vent apertures.
- Use oven gloves to remove pans and accessories, taking care not to touch the heating elements.
- Do not place flammable materials in or near the appliance: a fire may break out if the appliance is
inadvertently switched on.
- Do not heat or cook sealed jars or containers in the appliance. The pressure that builds up inside
might cause the jar to explode, damaging the appliance.
- Do not use containers made of synthetic materials.
- Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat and oil.
- Never leave the appliance unattended during food drying.
- If alcoholic beverages are used when cooking foods (e.g. rum, cognac, wine), remember that alcohol
evaporates at high temperatures. As a result, there is a risk that vapours released by the alcohol may
catch fire upon coming into contact with the electrical heating element.
IMPORTANT SAFETY INSTRUCTIONS
This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves
and others.
All safety warnings are preceded by the danger symbol and the following terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
GB2
Scrapping of household appliances
- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with
local waste disposal regulations. Before scrapping, cut off the power supply cable.
- For further information on the treatment, recovery and recycling of household electrical appliances,
contact your competent local authority, the collection service for household waste or the store where
you purchased the appliance.
After unpacking the oven, make sure that it has not been damaged during transport and that the oven
door closes properly. In the event of problems, contact the dealer or your nearest After-sales Service. To
prevent any damage, only remove the oven from its polystyrene foam base at the time of installation.
PREPARING THE HOUSING UNIT
Kitchen units in contact with the oven must be heat resistant (min 90°C).
Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all
wood chips and sawdust.
Ensure the levelness of the oven support surface.
After installation, the bottom of the oven must no longer be accessible.
For correct appliance operation, do not obstruct the minimum gap between the worktop and the
upper edge of the oven.
ELECTRICAL CONNECTION
Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The
dataplate is on the front edge of the oven (visible when the door is open).
Power cable replacement (type H05 RR-F 3 x 1.5 mm
2
) must be carried out by a qualified electrician.
Contact an authorized service centre.
GENERAL RECOMMENDATIONS
Before use:
- Remove cardboard protection pieces, protective film and adhesive labels from accessories.
- Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell
and fumes from the insulating materials and protective grease.
During use:
- Do not place heavy objects on the door as they could damage it.
- Do not cling to the door or hang anything from the handle.
- Do not cover the inside of the oven with aluminium foil.
- Never pour water into the inside of a hot oven; this could damage the enamel coating.
- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.
- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become
trapped in the door.
- Do not expose the oven to atmospheric agents.
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of
the packing must therefore be disposed of responsibly and in full compliance with local authority
regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and
Electronic Equipment (WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product.
INSTALLATION
SAFEGUARDING THE ENVIRONMENT
GB3
- The symbol on the product or on the accompanying documentation indicates that it should not be
treated as domestic waste but must be taken to an appropriate collection centre for the recycling of
electrical and electronic equipment.
Energy saving
- Only pre-heat the oven if specified in the cooking table or your recipe.
- Use dark lacquered or enamelled baking moulds as they absorb heat far better.
- This oven, which is intended to come into contact with foodstuffs, complies with European
Regulation ( ) n.1935/2004 and has been designed, manufactured and sold in conformity with the
safety requirements of the “Low Voltage” directive 2006/95/CE (which replaces 73/23/CEE and
subsequent amendments), the protection requirements of “EMC” 2004/108/CE.
The oven does not work:
Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
Turn off the oven and restart it to see if the fault persists.
The door will not open:
Turn off the oven and restart it to see if the fault persists.
The electronic programmer does not work:
If the display shows the letter “ followed by a number, contact your nearest After-sales Service.
Specify in this case the number that follows the letter “ .
Before calling the After-Sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the
Troubleshooting guide“.
2. Switch the appliance off and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
Always specify:
a brief description of the fault;
the type and exact model of the oven;
the service number (number after the word Service on the rating plate), located on the right hand
edge of the oven cavity (visible when the oven door is open). The service number is also indicated on
the guarantee booklet;
your full address;
your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original
spare parts will be used and repairs carried out correctly).
DECLARATION OF CONFORMITY
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
GB4
Oven exterior
IMPORTANT: Do not use corrosive or abrasive detergents. If any of these products accidentally
comes into contact with the appliance, clean it immediately with a damp cloth.
Clean the surfaces with a damp cloth. If very dirty, add a few drops of neutral detergent to the water.
Dry with a dry cloth.
Oven interior: STARCLEAN™ cleaning cycle
IMPORTANT: Do not use corrosive or abrasive detergents. Do not use abrasive sponges, metal
scrapers or scouring pads different from the sponge provided. Their use could eventually ruin the
enamelled surfaces. Only use non-abrasive sponges to clean the door glass.
The cavity of this oven is coated with a special formula enamel (nickel-free) enabling easily cleaning using
just water and the cellulose cloth provided. The cellulose cloth is washable and reusable until worn, and
can be purchased from the Customer Care Service. Washing the cloth in a washing-machine and drying it
in a dryer is inadvisable.
STARCLEAN™ cleaning cycle
To keep the oven in best condition, carry out the STARCLEAN™ cleaning cycle after each use. The cycle
takes 35 minutes, including a cooling stage, and must be carried out as follows:
1. Proceed with oven cold.
2. Wet the cellulose cloth provided under running water and wring it out so that it does not drip.
3. Open the oven door and remove the enamelled accessories.
4. Cover the bottom of the oven completely with the cellulose cloth.
5. Distribute 350 ml of water evenly on the cellulose cloth. A smaller or greater amount of water could
compromise proper functioning of the cycle.
6. Close the oven door.
7. Select the symbol with the functions knob: the word STARCLEAN™ appears on the display.
8. Press button to confirm the choice and start the cleaning cycle. To prevent steam coming out, do
not open the door during the cycle.
9. At the end of the cycle, remove the cellulose cloth and eliminate any residual water in the oven.
10. Then start cleaning using the sponge provided, moistened with hot water (cleaning could be
compromised if delayed by more than 15 minutes).
Particularly stubborn grime
To eliminate particularly stubborn grime, repeat the STARCLEAN™ cycle and add a few drops of neutral
detergent while removing the grime.
Cleaning inside glass
The inside surface of the door glass has a special coating that makes it easy to cleaning.
To keep the door glass in best condition, after every STARCLEAN™ cleaning cycle, clean the glass using just
water and a non-abrasive sponge.
Add a few drops of neutral detergent to the water to eliminate any greasy residuals.
NOTES:
The oven door can be removed to facilitate cleaning (see MAINTENANCE).
The top heating element of the grill (see MAINTENANCE) can be lowered to clean the roof of the
appliance.
During prolonged cooking of foods containing lots of water (e.g. pizza, vegetables, etc.),
condensation may form inside the door and on the seal. Dry with a cloth or sponge when the
oven is cold.
CLEANING
WARNING
- Never use steam cleaners.
- Clean the appliance when it is cold.
- Disconnect the appliance from the power supply.
GB5
Accessories:
Soak the accessories in water with washing up detergent after use, handling them with oven gloves if
still hot.
Food residues can be removed using a suitable brush or sponge.
Do not put the enamelled accessories in a dishwasher. The harsh detergents normally used in
dishwashers can permanently damage the enamel.
REMOVING THE DOOR
To remove the door:
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (Fig. 1).
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).
To refit the door:
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door.
MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)
1. Remove the side accessory holder grilles (Fig. 3).
2. Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).
3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to
rest on the lateral supports.
MAINTENANCE
WARNING
- Use protective gloves.
- Ensure the oven is cold before carrying out the following operations.
- Disconnect the appliance from the power supply.
Fig. 1 Fig. 2
Fig. 3 Fig. 4 Fig. 5
GB6
REPLACING THE OVEN LAMP
To replace the rear lamp (if present):
1. Disconnect the oven from the power supply.
2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover
back on.
3. Reconnect the oven to the power supply.
To replace the side lamp (if present):
1. Disconnect the oven from the power supply.
2. Remove the side accessory holder grilles, if present (Fig. 3).
3. Use a screwdriver to prise off the lamp cover (Fig. 7).
4. Replace the lamp (see note for lamp type) (Fig. 8).
5. Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).
6. Refit the side accessory holder grilles.
7. Reconnect the oven to the power supply.
N.B.:
- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C
halogen lamps.
- Lamps are available from our After-sales Service.
IMPORTANT:
- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.
- Do not use the oven until the lamp cover has been repositioned.
Fig. 6 Fig. 7 Fig. 8 Fig. 9
GB7
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
1. Control panel
2. Upper heating element/grill
3. Cooling fan (not visible)
4. Dataplate (not to be removed)
5. Light
6. Fan
7. Turnspit
8. Lower heating element (not visible)
9. Door
10. Position of shelves (the number of shelves is indicated on the front of the oven)
11. Rear wall
N.B.:
- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a
while.
- When the oven door is opened during cooking, the heating elements switch off.
ACCESSORIES SUPPLIED
A. WIRE SHELF (2): the wire shelf can be used to grill food or as a support for pans, cake tins and other
ovenproof cooking receptacles.
B. DRIP TRAY (1): the drip tray is designed to be positioned under the wire shelf in order to collect fat or
as an oven tray for cooking meat, fish, vegetables, focaccia, etc.
C. TURNSPIT (1): for uniform roasting of large pieces of meat and poultry.
D. CELLULOSE CLOTH (1): to be used for the STARCLEAN™ cleaning cycle.
IMPORTANT:Only use the cellulose cloth provided.
E. SPONGE: to be used for removing grime in the cavity
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-sales Service.
INSTRUCTIONS FOR OVEN USE
Fig. A Fig. B Fig. C Fig. D Fig. E
GB8
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
The wire shelf and other accessories are provided with a locking mechanism to prevent their unintentional
removal.
1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).
2. Angle the wire shelf when it reaches the locking position “B” (Fig. 2).
3. Return the wire shelf to the horizontal position and push it in fully to “C” (Fig. 3).
4. To remove the wire shelf proceed in reverse order.
The other accessories, like the drip tray and baking tray, are inserted in exactly the same way. The
protrusion on the flat surface enables the accessories to lock in place.
CONTROL PANEL DESCRIPTION
ELECTRONIC PROGRAMMER
1. FUNCTION SELECTOR KNOB: On/off and function selector knob
2. BROWSE KNOB: for browsing the menu and adjusting pre-set values
3. BUTTON : to return to the previous screen
4. BUTTON : to select and confirm settings
LIST OF FUNCTIONS
Turn the “Functions” knob to any position and the oven switches on: the display shows the functions or the
associated submenus.
The submenus are available and selectable by turning the knob to the functions GRILL, SPECIALS,
SETTINGS, BREAD/PIZZA.
N.B.:for the list and description of functions, see the specific table at page14.
Fig. 1
Fig. 2 Fig. 3
GB9
DESCRIPTION OF DISPLAY
A. Display of heating elements activated during the various cooking functions
B. Time management symbols: timer, cooking time, end of cooking time, time
C. Information regarding selected functions
D. Automatic BREAD/PIZZA function selected
E. Indication of door locked during automatic cleaning cycle (if present)
F. Internal oven temperature
G. Pyrolisis function (if present)
H. Browning
I. Special functions: Defrost, Keep Warm, Rising
STARTING THE OVEN - SETTING THE TIME
After connecting the oven to the mains power, the time must be set on the clock. The two hour digits flash
on the display.
1. Turn the “Browse” knob to display the correct hour.
2. Press the button to confirm; the two minute digits flash on the display.
3. Turn the “Browse” knob to display the correct minutes.
4. Press button to confirm.
To change the time, for example following a power cut, see the next paragraph (SETTINGS).
SELECTING COOKING FUNCTIONS
1. Turn the “Functions” knob to the desired function: the cooking settings are shown on the display.
2. If the values shown are those desired, press . To change them, proceed as indicated below.
SETTING THE TEMPERATURE/OUTPUT OF THE GRILL
To change the temperature or output of the grill, proceed as follows:
1. Turn the “Browse” knob to display the desired value.
2. Press button to confirm.
The oven automatically confirms your selection 10 seconds after the last operation.
A
B C D
E
I H G F
GB10
FAST PREHEATING
1. Turn the “Functions” knob to the symbol to select the fast preheating function.
2. Confirm by pressing : the settings are shown on the display.
3. If the proposed temperature is that desired, press button . To change the temperature, proceed as
described in previous paragraphs. The message PRE appears on the display. When the set
temperature is reached, the corresponding value (e.g. 200°C) appears on the display and the acoustic
signal sounds. At the end of preheating, the oven automatically selects the conventional function .
At this point food can be placed in the oven for cooking.
4. If you wish to set a different cooking function, turn the “Functions” knob and select the desired
function.
SETTING COOKING TIME
This function can be used to cook food for a set length of time, from a minimum of 1 minute to the
maximum time allowed by the selected function, after which the oven switches off automatically.
1. Once the temperature is confirmed, the symbol flashes.
2. Turn the adjustment knob to display the desired cooking time.
3. To confirm the cooking time, press button .
The oven automatically confirms your selection 10 seconds after the last operation.
SETTING END OF COOKING TIME/START DELAYED
IMPORTANT:the start delayed setting is not available for the following functions: FAST
PREHEATING, BREAD/PIZZA, GENTLE CONVECTION BAKE.
N.B.:with this setting, the selected temperature is reached in a more gradual way, so cooking times
will be slightly longer than stated in the cooking table.
The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and
59 minutes. This can only be done once cooking time has been set.
After setting cooking time, the display shows the end of cooking time (for example 15:45) and the
symbol flashes.
To delay the end of cooking time, and thus also the cooking start time, proceed as follows:
1. Turn the “Browse” knob to display the time you wish cooking to end (for example 16:00).
2. Confirm the selected value by pressing button : the two dots of end of cooking time flash,
indicating that the setting has been made correctly.
3. The oven will automatically delay the start of cooking so as to finish cooking at the set time.
At any time, however, set values (temperature, grill setting, cooking time) can be changed using
button to go back, followed by the “Browse” knob to change values and button to confirm.
INDICATION OF THE RESIDUAL HEAT INSIDE THE OVEN (IF PRESENT)
If at the end of cooking, or when the oven is switched off, the temperature inside the oven is high, the
display on some models shows the message HOT together with the current temperature. Once the oven
chamber has cooled down, the display shows the current time again.
GB11
TIMER
This function can be used only with the oven switched off and is useful, for example, for monitoring the
cooking time of pasta. The maximum time which can be set is 23 hours and 59 minutes.
1. With the “Functions” knob at zero, turn the “Browse” knob to display the desired time.
2. Press button to start the countdown. When the set time has elapsed, the display will show “0:00”
and an acoustic signal will sound. To mute the acoustic signal, press button (the time of day
appears on the display).
SELECTING SPECIAL FUNCTIONS
Turn the “Functions” knob indicator to the symbol to access a submenu containing three special
functions.
To browse, select and start one of these functions, proceed as follows:
1. Turn the “Functions” knob to symbol : the display shows “ DEFROST” along with this function’s
corresponding symbol.
2. Turn the “Browse” knob to scroll the list of functions; the function names are in English: DEFROST,
KEEP WARM, RISING.
3. Press button to confirm.
BROWNING
At the end of cooking, with certain functions, the display indicates the possibility of browning. This
function can only be used when cooking time has been set.
At the end of cooking time, the display shows: “PRESS TO BROWN”. Press button , and the oven starts
a 5 minute browning cycle. This function can be selected consecutively a maximum of twice.
BREAD/PIZZA FUNCTION SELECTION
Turn the “Functions” knob indicator to the symbol to access a submenu containing two automatic
cooking functions for “bread” and “pizza.
Bread
1. Turn the “Functions” knob to symbol : the display shows “BREAD” and AUTO at the side.
2. Press to select the function.
3. Turn the “Browse” knob to set the required temperature (between 180°C and 220°C) and confirm with
button .
4. Turn the “Browse” knob to set the required cooking duration and press to start cooking.
GB12
Pizza
1. Turn the Functions knob to symbol : the display shows “BREAD”. To select the “PIZZA” function,
proceed as follows:
2. Turn the “Browse” knob: “PIZZA” appears on the display.
3. Press to select the function.
4. Turn the “Browse” knob to set the required temperature (between 220°C and 250°C) and confirm with
button .
5. Turn the “Browse” knob to set the required cooking duration and press to start cooking.
SETTINGS
Turn the “Functions” knob indicator to the symbol to access a submenu containing four display
settings which can be changed.
Clock
Turn the “Functions” knob to the symbol : the word CLOCK appears on the display. To change the time
of day, see the previous paragraph (SETTING THE TIME).
Eco
With the ECO mode selected (ON), the display switches off when the oven is on standby or 5 minutes after
the end of cooking. To view information on the display, simply press a button or turn a knob.
1. Turn the “Browse” knob to display “ECO.
2. Press to access the setting (ON/OFF).
3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .
Acoustic signal
To activate or deactivate the acoustic signal, proceed as follows:
1. Turn the “Browse” knob to display “SOUND.
2. Press to access the setting (ON/OFF).
3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .
N.B.:when set to off, the following signals remain nonetheless active: timer end, preheating end,
cooking end.
Brightness
To change the display brightness, proceed as follows:
1. Turn the “Browse” knob to display “BRIGHTNESS.
2. Press button : the display shows LOW, MID or HIGH depending on the level currently set.
3. Turn the “Browse” knob to increase or decrease brightness and confirm by pressing .
GB13
STARCLEAN™ CLEANING CYCLE
To keep the oven in best condition, carry out the STARCLEAN™ cleaning cycle after each use. The cycle
takes 35 minutes, including a cooling stage, and must be carried out as follows:
For the description of this function, see the section CLEANING and the functions table on page14.
1. Proceed with oven cold.
2. Wet the cellulose cloth provided under running water and wring it out so that it does not drip.
3. Open the oven door and remove the enamelled accessories.
4. Cover the bottom of the oven completely with the cellulose cloth.
5. Distribute 350 ml of water evenly on the cellulose cloth. A smaller or greater amount of water could
compromise proper functioning of the cycle.
6. Close the oven door.
IMPORTANT:To prevent steam coming out, do not open the door during the cycle.
7. Select the symbol with the functions knob: the word STARCLEAN™ appears on the display.
8. Press button to confirm the choice and start the cleaning cycle. To prevent steam coming out, do
not open the door during the cycle.
9. At the end of the cycle, remove the cellulose cloth and eliminate any residual water in the oven.
10. Then start cleaning using the sponge provided, moistened with hot water (cleaning could be
compromised if delayed by more than 15 minutes).
Particularly stubborn grime
To eliminate particularly stubborn grime, repeat the STARCLEAN™ cycle and add a few drops of neutral
detergent while removing the grime.
KEY-LOCK
This function can be used to lock the buttons and knobs on the control panel.
To activate it, press and at the same time for at least 3 seconds. When activated, the functions
associated with the buttons are locked and the display shows a key symbol. This function can also be
activated during cooking. To deactivate it, repeat the above procedure. When the key-lock function is
activated, the oven can be switched off by turning the knob to 0 (zero). In this case, however, the previously
selected function will have to be set again.
GB14
FUNCTION DESCRIPTION TABLE
FUNCTIONS KNOB
OFF To stop cooking and switch off the oven.
LAMP To switch the oven interior light on/off.
SPECIALS
DEFROST
To speed up defrosting of food. Place food on the middle shelf. Leave food in
its packaging in order to prevent it from drying out on the outside.
KEEP WARM
For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans).
Place food on the middle shelf. The function will not activate if the
temperature in the oven is above 65°C.
RISING
For optimal rising of sweet or savoury dough. To safeguard the quality of
proving, the function will not activate if the temperature in the oven is above
40°C. Place the dough on the 2nd shelf. The oven does not have to be
preheated.
CONVENTIONAL
To cook any kind of dish on one shelf only. Use the 3rd shelf. To cook pizza,
savoury pies and sweets with liquid fillings, use the 1st or 2nd shelf. Preheat
the oven before placing food inside.
CONVECTION
BAKE
For baking cakes with liquid filling (sweet or savoury) on a single shelf. This
function can also be used for cooking on two shelves. Switch the position of
the dishes to cook food more evenly. Use the 3rd shelf to cook on one shelf
only, and the 1st and 4th to cook on two shelves. Preheat the oven before
cooking.
GENTLE
CONVECTION
BAKE -
GENTLE FAN
For cooking meat, filled pies (cheesecake, strudel, fruit pies) and stuffed
vegetables on one level only. This function uses discontinuous, delicate fan
assistance, which prevents excessive drying of foods. It is advisable to use
2nd level. Preheat the oven before cooking.
GRILL
To grill steak, kebabs and sausages; to cook vegetables au gratin and toast
bread. Place food on the 4th or 5th shelf. When grilling meat, use the drip
tray to collect the cooking juices. Position it on the 3rd/4th shelf, adding
approx. half a litre of water. The oven does not have to be preheated. During
cooking the oven door must remain closed.
TURBO GRILL
To roast large joints of meat (legs, roast beef, chickens). Position the food on
the middle shelves. Use the drip tray to collect the cooking juices. Position it
on the 1st/2nd shelf, adding approx. half a litre of water. The oven does not
have to be preheated. During cooking the oven door must remain closed.
With this function you can also use the turnspit, if provided.
MAXI COOKING
To cook large joints of meat (above 2.5 kg). Use the 1st or 2nd shelf,
depending on the size of the joint. The oven does not have to be preheated.
It is advisable to turn the meat over during cooking for more even browning.
It is best to baste the meat every now and again to avoid it drying out.
SETTINGS To set the display (time, brightness, buzzer volume, energy saving).
GB15
BREAD/PIZZA
To bake different types and sizes of pizza and bread. This function contains
two programmes with predefined settings. Simply indicate the values
required (temperature and time) and the oven will manage the cooking
cycle automatically. Place the dough on the 2nd shelf after preheating the
oven.
STARCLEAN™
To eliminate the dirt created by cooking by means of a low temperature
cycle. The combined action of the special enamel and the water released by
the cellulose cloth during the cycle facilitates removal of grime. Activate the
function when the oven is cold.
FAST PREHEATING To preheat the oven rapidly.
FUNCTIONS KNOB (Continued)
GB16
COOKING TABLE
Recipe Function Pre-
heating
Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
Leavened cakes
Yes 2/3 160-180 30-90 Cake tin on wire shelf
Yes 1-4 160-180 30-90
Shelf 4: cake tin on wire shelf
Shelf 1: cake tin on wire shelf
Filled pies (cheese-
cake, strudel, fruit
pie)
GENTLE
Yes 2 160-200 35-90
Drip tray/baking tray or cake
tin on wire shelf
Yes 1-4 160-200 35-90
Shelf 4: cake tin on wire shelf
(switch levels halfway
through cooking)
Shelf 1: cake tin on wire shelf
Biscuits / Tartlets
Yes 3 170-180 15-45 Drip tray / baking tray
Yes 1-4 160-170 20-45
Shelf 4: wire shelf
Shelf 1: drip tray / baking
tray
Choux buns
Yes 3 180-200 30-40 Drip tray / baking tray
Yes 1-4 180-190 35-45
Shelf 4: oven tray on wire
shelf
Shelf 1: drip tray / baking
tray
Meringues
Yes 3 90 110-150 Drip tray / baking tray
Yes 1-4 90 130-150
Shelf 4: oven tray on wire
shelf
Shelf 1: drip tray / baking
tray
Bread / Pizza /
Focaccia
Yes 1/2 190-250 15-50 Drip tray / baking tray
Yes 1-4 190-250 25-45
Shelf 4: oven tray on wire
shelf (switch levels halfway
through cooking)
Shelf 1: drip tray / baking
tray
Bread
(Bread)
Yes 2 180-220 30-50
Drip tray / baking tray or
wire shelf
Pizza
(Pizza)
Yes 2 220-250 15-30 Drip tray / baking tray
Frozen pizza
Yes 3 250 10-15
Shelf 3: drip tray / baking
tray or wire shelf
Yes 1-4 250 10-20
Shelf 4: oven tray on wire
shelf (switch levels halfway
through cooking)
Shelf 1: drip tray / baking
tray
GB17
Savoury pies (veg-
etable pie, quiche)
Yes 3 180-190 40-55 Cake tin on wire shelf
Yes 1-4 180-190 40-55
Shelf 4: cake tin on wire shelf
(switch levels halfway
through cooking)
Shelf 1: cake tin on wire shelf
Vols-au-vent / Puff
pastry crackers
Yes 3 190-200 20-30 Drip tray / baking tray
Yes 1-4 180-190 15-40
Shelf 4: oven tray on wire
shelf
Shelf 1: drip tray / baking
tray
Lasagne / Baked
pasta / Cannelloni /
Flans
Yes 3 190-200 45-55 Oven tray on wire shelf
Lamb / Veal / Beef /
Pork 1 Kg
GENTLE
Yes 2 180-190 80-120
Drip tray or oven tray on
wire shelf
Chicken / Rabbit /
Duck 1 Kg
GENTLE
Yes 3 200-220 50-100
Drip tray or oven tray on
wire shelf
Turkey / Goose
3Kg
Yes 2 190-200 80-130
Drip tray or oven tray on
wire shelf
Baked fish / en
papillote (fillet,
whole)
Yes 3 180-200 40-60
Drip tray or oven tray on
wire shelf
Stuffed vegetables
(tomatoes, cour-
gettes, aubergines)
Yes 2 170-190 30-60 Oven tray on wire shelf
Toas t - 5 3 (High) 3-6 Wire shelf
Fish fillets / steaks - 4 2 (Medium)
20-30
Shelf 4: wire shelf (turn food
halfway through cooking)
20-30 Shelf 3: drip tray with water
Sausages / Kebabs
/ Spare ribs / Ham-
burgers
- 5
2-3
(Medium-
High)
15-30
Shelf 5: wire shelf (turn food
halfway through cooking)
Shelf 4: drip tray with water
Roast chicken
1-1.3 Kg
- 2 2 (Medium) 55-70
Shelf 2: wire tray (turn food
two thirds of the way
through cooking)
- 2 3 (High) 60-80 Shelf 2: turnspit (if present)
Roast Beef rare
1Kg
- 3 2 (Medium) 35-45
Oven tray on wire shelf (turn
food two thirds of the way
through cooking if
necessary)
Leg of lamb /
Shanks
- 3 2 (Medium) 60-90
Drip tray or oven tray on
wire shelf (turn food two
thirds of the way through
cooking if necessary)
Recipe Function Pre-
heating
Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
GB18
* Cooking time is approximate. Food can be removed from the oven at different times depending on
personal preference.
Roast potatoes - 3 2 (Medium) 45-55
Drip-tray / baking tray (if
necessary, turn food two
thirds of the way through
cooking)
Vegetable gratin - 3 3 (High) 10-15 Oven tray on wire shelf
Lasagne & Meat Yes 1-4 200 50-100*
Shelf Oven tray on wire shelf
(turn food two thirds of the
way through cooking if
necessary)
Shelf 1: drip tray or oven tray
on wire shelf
Meat & Potatoes Yes 1-4 200 45-100*
Shelf Oven tray on wire shelf
(turn food two thirds of the
way through cooking if
necessary)
Shelf 1: drip tray or oven tray
on wire shelf
Fish & Vegetables Yes 1-4 180 30-50*
Shelf 4: oven tray on wire
shelf
Shelf 1: drip tray or oven tray
on wire shelf
Recipe Function Pre-
heating
Shelf (from
bottom)
Temp.
(°C)
Time
(min)
Accessories and notes
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Whirlpool AKZM 831/IX Mode d'emploi

Catégorie
Fours
Taper
Mode d'emploi

dans d''autres langues