Document
Document Details
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
V1.0 (20210929)
(V1.0 first published 20210929)
Firmware
Firmware version can be verified on
Verkada Command command.verkada.com.
2
Introduction
What’s in the box
What you’ll need
●BH61 Wireless Alarm Hub
●A working internet connection
●Smartphone or laptop
●#2 phillips driver (screwdriver or power
drill)
●0.1 inch (2.5mm) drill bit for pilot holes
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Connect
Please note: Add your BH61 Wireless Alarm Hub
to Command before setting up your Wireless
Door Sensor.
●To register your product, please
proceed to: verkada.com/start
1x Sensor
Module
2x CR123A batteries
4x Wood Screws
4x Sheet metal
Screws
1x T10 Security
Torx L key
1x Magnet
Module
1x Sensor Module
Mounting Tape
1x Magnet Module
Mounting Tape
3
Introduction
Sensor overview
LED Behavior
Test mode
To enable test mode, press the top button. While in test mode, the green LED will:
●turn on when the sensor is separated from the magnet (door opened).
●turn off when the sensor is brought close to the magnet (door closed).
After ten minutes in test mode, the device will return to normal operation.
Normal operation
While in normal operation, the green LED will:
●NOT turn on when the sensor is separated form the magnet.
●flash rapidly three times every two minutes to indicate low battery.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Test mode button
Status LED
(Glow-though)
Sensor Module
Sensor Mount
Magnet mount
and cover
4
Installation
Mounting 1/5
Use the provided T10 Security Torx
L-key to unscrew the security screw at
the bottom of the product.
Swing the sensor module out
and disengage the hooks at the
top of the sensor mount.
Remove the battery pull tabs.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
5
Installation
Mounting 2/5
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
While the device is in test mode,
place the sensor module and the
magnet piece on the desired
surfaces to see if the sensor
registers a closed door (the
sensor module’s LED will turn off
when it senses a closed door).
With a screwdriver, make pilot
holes and screw the sensor
mount into place.
Door Door frame
Door Door frame
6
Engage the hooks at the top of the
sensor mount and swing the sensor
module into place.
Installation
Mounting 3/5
Use the provided T10 Security Torx
L-key to unscrew the security screw at
the bottom of the magnet.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Swing the magnet cover out and
disengage the hook at the top of
the magnet cover.
Make sure to align the “Align”
mark and screw the magnet
piece on to the desired surface.
Door Door frame
7
Installation
Mounting 4/5
Use the provided T10 Security
Torx L-key to secure the security
screw in place.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Engage the hooks at the top of the
sensor mount and swing the sensor
module into place.
Door Door frame
Door Door frame
8
Installation
Mounting 5/5
Use the provided T10 Security
Torx L-key to secure the security
screw in place.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Engage the hook at the top of the
magnet cover and swing the magnet
cover into place.
Door Door frame
Door Door frame
9
Appendix
BR31 Compliance
FCC
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance may void the user’s authority to operate his equipment. (Example – use only
shielded interface cables when connecting to computer or peripheral devices)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance 20cm between the radiator & your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
IC
Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference;
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la
conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la
conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou
émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres
entre le radiateur et votre corps.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
10
Appendix
Support
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Thank you for purchasing this Verkada product. If for any reason
things don’t work right, or you need assistance, please contact us
immediately.
verkada.com/support
Sincerely, The Verkada Team
11
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Verkada BR31 Wireless Door Sensor Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Verkada Br35 Guide d'installation
-
-
-
-
Verkada BR32 Guide d'installation
-
-
-
Verkada AD33 Guide d'installation
-
-