VTech EW780 Manuel utilisateur

Marque: VTech

Modèle: EW780

Catégorie: Moniteurs vidéo bébé

Taper: Manuel utilisateur

Night vision

The baby unit has infrared LEDs that allow

you to see your baby clearly at night or in

a dark room. When the baby unit being

viewed detects low light levels, the infrared

LEDs are switched on automatically. The

images from the baby unit are in black and

white, and appears on the screen.

Notes

• It is normal if you see a short white glare on

your parent unit screen as the baby unit is

adapting to the dark environment.

• When the infrared LEDs are on, the images are

in black and white. This is normal.

Tip

• Depending on the surroundings and other

interfering factors, like lightings, objects, colors

and backgrounds, the video quality may vary.

Adjust the baby unit’s angle or place the baby

unit at a higher level to prevent glare and

blurry display.

Mount the baby unit on dry wall (optional)

For VM919-2HD only

Select Patrol mode as your monitoring

mode to alternately view the image

from baby units and every

10 seconds.

Change different views - Patrol

Select Split mode as your monitoring mode to view the images

from both baby units at once.

Note

• While in Split mode, you can press or to highlight the view of the baby unit 1 or

baby unit 2 , and hear the sounds transmitted from the baby unit.

Change different views - Split

Sound Detection and Auto Wake UP

Sound activated screen and audio - Auto Wake Up

Adjust sound detection sensitivity

When Auto Wake Up is turned on,

the parent unit screen stays off to

save power when the baby unit

detects no sound.

Once the baby unit detects sounds

that are louder than the chosen

sound sensitivity level, the parent

unit screen and speaker turn on

automatically. The parent unit will

then turn off again after 50 seconds

of no sound detection.

NOTESNOTE

Notes

• If you have muted the parent unit

speaker, only the parent unit screen

will turn on when a sound is detected.

• If you have turned on Auto Wake

Up but turned off Sound Detection

Alert, the parent unit will wake up

when the baby unit detects sounds

that are louder than the chosen sound

sensitivity level.

You can turn on Sound Detection Alert and adjust the Sound Sensitivity to detect sounds

and turn on the parent unit while its screen is switched off or dimmed.

When the baby unit detects sounds that exceed certain levels, the parent unit screen will

turn on and the baby unit starts transmitting the sounds to the parent unit, and you can

see and hear your baby.

If you have turned on Sound Detection Alert, the parent unit beeps when the baby unit

detect sounds.

The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and recycle these batteries at the end of their useful lives,

when taken out of service within the United States and Canada.

The program provides a convenient alternative to placing used lithium-ion batteries into the trash or

municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or

at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and

disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized

service representative will repair or replace at VTech’s option,

without charge, a Materially Defective Product. If we repair

the Product, we may use new or refurbished replacement

parts. If we choose to replace the Product, we may replace

it with a new or refurbished Product of the same or

similar design. We will retain defective parts, modules,

or equipment. Repair or replacement of the Product, at

VTech’s option, is your exclusive remedy. VTech will return

the repaired or replacement Products to you in working

condition. You should expect the repair or replacement to

take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for

ONE (1) YEAR from the date of purchase. If VTech repairs or

replaces a Materially Defective Product under the terms of

this limited warranty, this limited warranty also applies to the

repaired or replacement Product for a period of either (a)

90 days from the date the repaired or replacement Product

is shipped to you or (b) the time remaining on the original

one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our

website at www.vtechphones.com or call 1 (800) 595-9511.

In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of the Product(s) to the service location. VTech

will return repaired or replaced Product under this limited

warranty. Transportation, delivery or handling charges are

prepaid. VTech assumes no risk for damage or loss of the

Product in transit. If the Product failure is not covered by

this limited warranty, or proof of purchase does not meet

the terms of this limited warranty, VTech will notify you and

will request that you authorize the cost of repair prior to any

further repair activity. You must pay for the cost of repair and

return shipping costs for the repair of Products that are not

covered by this limited warranty.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the

Product. There are no other express warranties. No one is

authorized to make modiﬁcations to this limited warranty and

you should not rely on any such modiﬁcation. State/Provincial

Law Rights: This warranty gives you speciﬁc legal rights, and

you may also have other rights, which vary from state to state

or province to province.

Limitations: Implied warranties, including those of ﬁtness

for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost of

substitute equipment, and claims by third parties) resulting

from the use of this Product. Some states/provinces

do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion

may not apply to you.

Please retain your original sales receipt as proof

of purchase.

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor

is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge

the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby

units, the CEC battery charging testing mode is activated while it is powered off and charging.

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the

Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed

by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of

approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your

face.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause

interference. (2) This device must accept any interference, including interference that may cause undesired operation of the

device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations were

met.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should

be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other

accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect

to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

The RBRC seal For cETL compliance only Limited warranty

California Energy Commission battery

charging testing mode

FCC and IC regulations

10:25 AM

10s

The parent unit display will dim to conserve energy after 5 minutes of inactivity, in

which there is neither key pressed nor alert received from the baby unit.

Dim mode

5 minute inactivity

Press any buttons

Sound

Sensitivity

level

Level 3

(Highest)

Level 2

(Medium)

Level 1

(Lowest)

Description The parent unit screen and

speaker turn on for very

small sounds, including

background noises from

your baby’s room.

The parent unit screen and

speaker turns on for loud

babbling and louder sounds

from your baby. The parent

unit remains quiet when your

baby makes soft sounds.

The parent unit screen

and speaker turn on for

loud crying or screeching

sounds from your baby.

The parent unit remains

quiet when your baby

makes soft sounds.

1. Place the wall mount bracket on a wall and then use

a pencil to mark the top and the bottom holes as

shown. Remove the wall mount bracket and drill

two holes in the wall (7/32 inch drill bit).

NOTESNOTE

Notes

• Check for reception strength and baby unit’s angle before drilling the holes.

• The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the screws and anchors separately to mount your baby units.

2. If you drill the holes into a stud, go to step 3.

• If you drill the holes into an object other than a stud, insert the wall

anchors into the holes. Tap gently on the ends with a hammer until the

wall anchors are ﬂush with the wall.

3. Align the wall mount bracket and screws with the

holes in the wall as shown. Tighten the screw in the

middle hole ﬁrst, so that the wall mount bracket

position is ﬁxed. You can tighten the other screw in

the top hole.

3. Insert the screws into the holes and tighten the screws until only 1/4 inch

of the screws are exposed.

4. Place the baby unit on the wall mount bracket.

Tighten the screw into the threaded socket

at the bottom to secure the baby unit. Align

the holes on the wall mount bracket with the

screws on the wall, and slide the wall mount

bracket down until it locks into place.

5. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.

Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket.

Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and

secure the angle.

4. Place the baby unit on the wall mount bracket.

Tighten the screw into the threaded socket at the

bottom to secure the baby unit.

Motion Detection

Adjust motion detection sensitivity

You can turn on Motion Alert and adjust the Motion Sensitivity to detect motions and

turn on the parent unit while its screen is switched off or dimmed.

When the baby unit’s camera detects motions that exceed certain levels, the parent unit

screen will turn on and the baby unit starts transmitting the sounds to the parent unit, and

you can see and hear your baby.

If you have turned on Motion Alert, the parent unit beeps when the baby unit detects

motions.

Motion

Sensitivity

level

Level 3

(Highest)

Level 2

(Medium)

Level 1

(Lowest)

Description The parent unit screen and

speaker turn on for small

motions, such as yawning or

stretching.

The parent unit screen and

speaker turns on for normal

daily motions, such as

people walking around the

house.

The parent unit screen and

speaker turn on for large

motions, such as children

are chasing or jumping

around. Monitoring mode

Change different views - Single CAM

Select baby unit 1 or baby unit 2 to

view the image from the baby unit.

Below are the questions most frequently asked about the baby monitor.

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby units and the parent unit.

2. Wait a few seconds before connecting power back to the baby units and the parent unit.

3. Turn on the baby units and the parent unit.

4. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for

this to take place.

Why don’t the lights of

the baby unit and parent

unit go on when I switch

on the units?

Perhaps the parent unit’s battery is depleted. Insert the appliance plug into the parent

unit and put the adapter in a wall socket. The parent unit will establish connection with

the baby unit.

Perhaps the baby unit is not connected to the power. Insert the appliance plug into the

baby unit and put the adapter in a wall socket. Then, slide the ON/OFF to switch on the

baby unit and to establish connection with the parent unit.

Why doesn’t my parent

unit charge while

connected to AC power?

Make sure the power is not controlled by a wall switch.

Why is my screen in black

and white?

The screen is in black and white during night-time or in a dark room when the night

vision feature is activated. This is normal.

Why do I get glare or

blurry display on my

screen when viewing my

baby at night?

During night-time or in a dark room, the surroundings and other interfering factors,

like lightings, objects, colors and backgrounds may affect the image quality on your

parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to

prevent glare and blurry display.

Why does the baby

monitor produce a

high-pitched noise?

The parent unit and baby units may be too close to each other.

• Move the parent unit away from the baby units until the noise stops; OR

• Turn down the volume of your parent unit.

Why does the parent unit

beep?

The baby units may be out of range. Move the parent unit closer to the baby units (but

not less than 3 feet).

The parent unit may not have enough charge for the parent unit to perform normally.

Charge the battery in the parent unit until the battery icon becomes solid .

The temperature of your baby’s room may be too high or too low.

Why don’t I hear a sound/

Why can’t I hear my baby

cry?

The parent unit speaker volume may be too low. Press VOL+ to increase the volume, or

use the parent unit menu to change sound sensitivity level to the highest level.

Why can’t I establish a

connection? Why is the

connection lost every now

and then? Why are there

sound interruptions?

The baby units may be out of range. Move the parent unit closer to the baby units (but

not less than 3 feet).

Other electronic and wireless products may cause interference with your baby monitor.

Try installing your baby monitor as far away from these devices as possible.

If you power on only one baby unit, your parent unit may display Make sure baby unit X

is on or move closer to baby unit X, and the LINK LED light ﬂashes. Switch to the baby unit

you have powered on via menu.

Frequently asked questions

Mesures de sécurité importantes

La plaque signalétique appliquée est située au bas du socle de l’unité

du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre

certaines mesures de précaution de base aﬁn de réduire les risques

d’incendie, d’électrocution et de blessures corporelles, dont ceux qui

suivent:

1. Observez toutes les instructions et mises en garde inscrites sur

l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

4. Ce produit a été conçu pour être un dispositif d’appoint seulement.

Il n’est pas le remplacement d’une supervision responsable et

adéquate par un adulte et ne devrait pas être utilisé comme telle.

5. Ce produit n’est pas conçu pour être utilisé en tant que moniteur

médical.

6. N’utilisez pas cet appareil près de l’eau ni de toute autre source

d’humidité, par exemple, près d’une baignoire, cuve à lessive,

évier de cuisine, dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

7. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque

d’explosion pourrait survenir si un mauvais type de pile est utilisé

pour l’unité du parent. La pile ne peut pas être soumise à des

températures extrêmes élevées ou basses et à une faible pression

d’air à haute altitude pendant l’utilisation, l’entreposage ou le

transport. L’élimination de la pile dans le feu ou dans un four chaud,

ou l’écrasement ou le découpage mécanique de la pile peuvent

entraîner une explosion. Laisser la pile dans un environnement à

température extrêmement élevée peut entraîner une explosion

ou la fuite d’un liquide ou d’un gaz inﬂammable. Une pile soumise

à une pression d’air extrêmement basse peut provoquer une

explosion ou une fuite de liquide ou de gaz inﬂammable. Éliminer

la pile usagée conformément aux informations du Sceau RBRC.

8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation

d’un adaptateur dont la polarité ou la tension serait inadéquate

risque d’endommager sérieusement le produit et mettre votre

sécurité en péril.

Informations sur les adaptateurs électriques :

Adaptateur de l’unité du bébé: Sortie : 5 V CC 1A.

VTech Telecommunications Ltd.

Modèle : VT05EUS05100

Adaptateur de l’unité du parent: Sortie : 5 V CC 2A.

VTech Telecommunications Ltd.

Modèle : VT07EUS05200

Informations sur les piles rechargeables :

3.7V 5000mAh, 18.5Wh Lithium-ion Battery

Zhuhai Great Power Energy Co., Ltd.

Modèle : GSP806090-5Ah-3.7V-1S1P

9. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs

secteur ont été conçus pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas été conçues pour

supporter le poids du bloc d’alimentation et le maintenir en place

si celuici est branché dans une prise au plafond, sous une table ou

dans un meuble.

10. Pour les appareils raccordés, la prise de courant (de l’adaptateur

secteur) doit être installée près de l’équipement et doit être

facilement accessible.

11. Débranchez ce produit de la prise de courant avant de procéder

au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un

chiffon humide pour le nettoyer.

12. Ne coupez pas les cordons d’alimentation pour remplacer les

ﬁches, car ceci peut présenter un danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit où

l’on risque d’écraser le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation

indiqué sur l’étiquette. Si vous ne connaissez pas le type

d’alimentation que vous possédez à votre domicile, consultez votre

marchand ou votre compagnie locale d’électricité.

15. L’équipement doit être fourni à partir d’un acquiescement gauche

identiﬁé d’USB aux conditions de la source d’énergie limitée.

16. Ne surchargez pas les prises de courant murales ni les rallonges

électriques.

17. Ne placez pas cet appareil sur un chariot, meuble, trépied, support

de montage ni table chancelants.

18. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil

ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de

surchauffer, ne bloquez sous aucun prétexte ces ouvertures

et n’empêchez pas l’aération adéquate de l’appareil en le

plaçant sur un lit, divan, tapis ou toute autre surface similaire.

De même, ne le positionnez pas à proximité ni au-dessus d’une

source de chaleur ou d’un calorifère. De plus, ne placez pas

l’appareil dans un endroit avant de vous assurer qu’il y ait une

bonne circulation d’air.

19. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil,

car ils pourraient entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui peuvent dégénérer

en incendies ou en risques d’électrocution. Ne renversez jamais

de liquide dans ce produit.

20. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet

appareil, mais apportez-le dans un centre de service autorisé.

L’ouverture du boîtier ou le retrait de toutes pièces que contient

cet appareil, à l’exception de l’accès autorisé à certaines portes

ou ouvertures, risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage incorrect peut par

la suite présenter des risques d’électrocution.

21. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

22. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas

endommagées.

23. Il existe un très faible risque de perte de conﬁdentialité avec

certains appareils électroniques (autres écoute-bébés, téléphones

sans ﬁls etc.). Pour l’éviter, s’assurer que le produit n’a jamais été

utilisé avant l’achat, réinitialiser l’unité de façon périodique, éteindre

l’écoute-bébé quand il n’est pas en cours d’utilisation.

24. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils ne

jouent pas avec l’appareil.

25. Les petites pièces de ce moniteur peuvent être avalées par les

bébés ou les petits enfants. Veuillez tenir ces pièces hors de

portée des enfants.

26. Le produit n’est pas conçu pour être utilisé par des personnes

(incluant des enfants) aux capacités physiques, sensorielles

ou mentales réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné sufﬁsamment de

supervision ou d’instructions relativement à l’utilisation de l’appareil

par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

• Utilisez et entreposez le produit à une température entre 0˚ C

(32˚F) et 40˚C (104˚ F).

• Risque de brûlure, risque d’incendie, risque d’explosion associé à

une mauvaise manipulation de la batterie.

• N’exposez pas cet appareil à des froids ou des chaleurs extrêmes,

ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une

source de chauffage.

• Avertissement - Risque de strangulation

- Les enfants se sont ÉTRANGLÉS dans des cordons.

Gardez ce cordon hors de portée des enfants (à

plus de 0,9 m). N’enlevez pas cette étiquette.

• Ne jamais placer le moniteur à l’intérieur du berceau ou du parc

de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec

un article tel une serviette ou une couverture.

• D’autres produits électroniques peuvent causer des interférences

auprès de votre caméra IP. Essayez d’installer votre caméra IP le

plus loin possible de ces dispositifs électroniques : routeurs sans ﬁl,

radios, téléphones cellulaires, interphones, moniteurs de pièces,

téléviseurs, ordinateurs personnels, appareils électriques de cuisine

et téléphones sans ﬁl.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans ﬁl):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme

de recherche indépendante, a mené une évaluation pluridisciplinaire

des interférences entre les téléphones sans ﬁl portatifs et les

stimulateurs cardiaques implantés dans l’organisme. Appuyée par

l’Administration des aliments et drogues (FDA) des États-Unis, la ﬁrme

WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans ﬁl à au moins six pouces

du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur le

stimulateur cardiaque, tel que dans une poche de chemise, lor-

sque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque

pour les détenteurs de simulateurs cardiaques causés par les gens qui

utilisent dispositifs sans ﬁl à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant

aux champs électromagnétiques (EMF) standard. Si vous le manipulez

correctement en suivant les instructions de ce guide, son utilisation

sera sécuritaire pendant de nombreuses années, selon les meilleures

évidences scientiﬁques dont nous disposons aujourd’hui.

VTech EW780 Manuel utilisateur

Marque: VTech

Modèle: EW780

Catégorie: Moniteurs vidéo bébé

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech EW780 User manual

VTech EW780 Manuel utilisateur

VTech EW780 Manuel utilisateur

dans d''autres langues

Documents connexes