SELECT HINGES SL53 HD Heavy Duty Half Surface Geared Continous Hinges Manuel utilisateur

Marque: SELECT HINGES

Modèle: SL53 HD Heavy Duty Half Surface Geared Continous Hinges

Taper: Manuel utilisateur

Ph: 800-423-1174 | Fax: 800-423-7107 | www.select-hinges.com

Information subject to

change without notice.

Important Warranty Information:

The following actions will void any warranty, expressed or implied:

QFailure to install the hinge according to manufacturer's speciﬁcations and

requirements. (For more information, visit selecthingerequirements.com.)

QUse of fasteners other than those supplied with the hinge.

QUnauthorized ﬁeld modiﬁcations, including alteration or removal of the

factory-applied lubricant, altering the original ﬁnish or painting the hinge.

SEE BELOW

1-1/16"

1-3/4"

4-1/2"

7/16"

1-3/16"

SL77 CENTER HUNG

APPLICATION †

3/32"

1-9/16"

1-3/16"

1-1/16"

1-7/8"

7/16"

11/16"

SEE BELOW

SL53

3/32"

1-29/32"

1-3/16"

1-1/16"

1-7/8"

7/16"

11/16"

SEE BELOW

SL54

3/32"

1-9/16" 1-11/16"

1-1/16" 7/16"

11/16"

1-3/16"

SEE BELOW

SL77 SAFETY HINGE

APPLICATION †

Single Door

Hinge side clearance

SL53 & SL54 *3/16"

SL77 Center Hung *5/32"

SL77 Safety Hinge *13/16"

INSTALLATION INSTRUCTIONS

Half Surface Geared Continuous Hinges

Reinforcing & Rivnuts®

No hinge reinforcement is necessary except on

extremely high-frequency, extremely heavy or extra-

wide doors. Rivnuts are recommended for use in the

frame when the door exceeds 450 lb. (max. 600 lb.)

NOTE: Only SELECT steel Rivnuts® are to be used

with ﬁre-rated SELECT hinges.

Grouted/Slushed-in Frames

For ease of installation, it is recommended some sort

of mudguard be installed behind the frame. Do not

use self-drilling, thread-forming (SDTF) screws to

drill into grouted frames. If mudguards have not been

used, carefully drill pilot holes through frame and

remove grout for screw clearance. Do not oversize

holes in frame.

Fire-Rated Hinges †

All stock SELECT hinges are 90-minute

UL-rated, without pins. Please contact

SELECT for complete information about

itsﬁre-ratedhinges.

† Please note the SL77 is notﬁre-rated.

*1/8"

*1/8"– 3/16"

Door Clearances

For Square and Beveled-Edge Doors

IMPORTANT: All uncut SL53, SL54 and SL77 hinges

are non-handed and templated. Theybecome handed

after cutting. Ifdoor inset is required, install acontinuous

piece ofshimunder the door leaf.

YLX\PYLTLU[ZVUÄYLYH[LKLU[YHUJLZ

† Please note the SL77 is not ﬁre-rated.

* Same clearance

as opposite side

Double Doors

(Pair)

Hinge side clearance

SL53 & SL54 *3/16"

SL77 Center Hung *5/32"

SL77 Safety Hinge *13/16"

Ph: 800-423-1174 | Fax: 800-423-7107 | www.select-hinges.com Information subject to

change without notice.

How to Cut the Hinge to Fit

A. Keep hinge in “door closed” position

(Fig. 1).

B. Determine whether this will be a right-

hand or left-hand installation.

IMPORTANT: Cut only one end of hinge.

Cut end will be installed at the bottom. Keep

original templated six-hole pattern at top

end of hinge.

C. Using a metal-cutting saw, begin the

cut through the gear cap ﬁrst.

NOTE: DO NOT cut through a set screw

bearing.

D. Loosen set screw from side of door leaf

cover with 5/64" Allen wrench (Fig. 1).

E. Remove door leaf cover by sliding it o

uncut end of hinge.

F. Reinstall any set screw bearing that

may have been cut o.

A. Attach Hinge to Frame

NOTE: Remove door leaf cover if not

already removed. See step D above.

1. Shim hinge to 1/8" below the header to

allow for door clearance.

2. Hold hinge in “door open” position (Fig.

2) making sure frame leaf alignment

ﬂange is tight against frame rabbet.

3. Mark (or centerpunch) two holes at top

and two holes at bottom of frame leaf.

NOTE: TF screws and wood screws require

pilot holes at marked locations. SDTF

screws do not require pilot holes.

4. If using SDTF screws, go to Step 5. If

using TF or wood screws, drill holes at

marked locations.

QMetal frame: Use #13 (.185") bit or

3/16" (.188") bit

QWood frame: Use a 5/32" (.156") bit

5. Fasten frame leaf to door frame using

two screws at the top and two screws

at the bottom.

QMetal frame : Use #12-24 TF ﬂathead

screws provided, or use #12-24

SDTF ﬂathead screws (provided on

request)

QWood frame: Use #12 ﬂathead wood

screws (provided on request)

B. Prepare Door

6. Shim door into opening to provide

required hinge clearances.

IMPORTANT: Top end of the hinge must be

ﬂush with the top of the door.

IMPORTANT: A 13/16" gap between

door edge and a frame without a stop is

necessary for the SL77 safety feature to be

eective.

See illustration on other side.

7. Mark locations for the four SDTF

panhead screws on the door using

7/32" center punch.

8. With #3 Phillips drive, temporarily

attach door leaf to door through the

four locator holes with SDTF panhead

screws provided.

9. Remove shims and check door

clearances, alignment and operation.

NOTE: Door may sag slightly when

shims are removed. Note the amount of

adjustment needed to bring door back into

alignment.

DO NOT PROCEED UNTIL DOOR

OPERATES PROPERLY.

10. Mark locations for barrel nuts on the

door using 3/8" center punch.

11. Remove door and lay it ﬂat. Use

3/8" drill bit to drill holes at marked

locations.

NOTE: Be sure to drill squarely through

door.

C. Attach Door to Hinge

12. Fasten door to door leaf with the barrel

nuts and 1/4-20 shoulder screws.

NOTE: Always install shoulder screws on

the secured side of the door (Fig. 3).

13. Mark (or centerpunch) remaining frame

leaf hole locations. Drill holes in frame

through the frame leaf and secure with

ﬂathead screws.

14. Secure door to door leaf with barrel

nuts and 1/4-20 shoulder screws.

NOTE: Always install shoulder screws on

the secured side of the door (Fig. 3).

D. Install Leaf Cover

15. Align leaf cover with top edge of hinge.

16. Starting from the top and working

downward, apply pressure to leaf cover

to snap it into place (Fig. 3).

NOTE: If you use a hammer to tap cover

into place, be sure to protect the surface of

the cover from damage.

17. Tighten set screws with 5/64" Allen

wrench.

Tools Needed

QMetal-cutting saw

QTape measure

Q#13 or 3/16" drill bit & 3/8" drill bit

Q5/32" drill bit (wood frames only)

Q#3 Phillips drive

Q5/64" Allen wrench

QHammer

QShims

Parts Supplied

Q#12-24 self-drilling, thread-forming

(SDTF) 410 SS Phillips undercut

ﬂathead screws

Q#12-24 self-drilling, thread-forming

(SDTF) 410 SS Phillips undercut

panhead screws

Q1/4-20 barrel nuts (through bolts)

Q1/4-20 shoulder screws

Q7/32" center punch

Q3/8" center punch

QSet screws

Optional Parts

Q#12 410 SS Phillips undercut

ﬂathead wood screws

Q#12-24 thread-forming (TF)

410 SS Phillips undercut ﬂathead

screws

QLong barrel nuts for doors

2"—2-1/4" thick

QProtective gloves are

recommended

Gear Cap

Frame

Leaf

Door

Leaf

Frame

Door

Set

Screw

Fig. 1 Door Closed Position

Gear

Cap

Frame

Leaf

Door

Leaf

Frame

Door

Fig. 2 Door Open 90˚

Gear Cap Door Leaf

Cover

Frame

Door

Set Screw

Shoulder Screw

SECURED SIDE, OUTSWING

Barrel Nut

(not to

scale)

NOTE: For inswing applications, reverse

position of barrel nut and shoulder

screw so that the shoulder screw is

on the secured side of the door.

Fig. 2 Leaf Cover Installation

SELECT HINGES SL53 HD Heavy Duty Half Surface Geared Continous Hinges Manuel utilisateur

Marque: SELECT HINGES

Modèle: SL53 HD Heavy Duty Half Surface Geared Continous Hinges

Taper: Manuel utilisateur

Télécharger le PDF

rapport

SELECT HINGES SL53 HD Heavy Duty Half Surface Geared Continous Hinges Manuel utilisateur

SELECT HINGES SL53 HD Heavy Duty Half Surface Geared Continous Hinges Manuel utilisateur

dans d''autres langues

Autres documents