Deckorators 239721-16 Guide d'installation

Marque: Deckorators

Modèle: 239721-16

Taper: Guide d'installation

EOVATIONS INSTALLATION GUIDE

Items you will need

• Safety glasses

• Pencil or pen

• Tape measure

• Utility knife

• Jigsaw

• Carpenter square

(speed square)

• Power screw gun or drill

• Soft mallet

• Portable power saw

• Fine-tooth saw blades

(40-tooth minimum, sharp

carbide-tipped wood or

ﬁnish/trim blades)

• Large ﬁle or medium-grit

sandpaper

• Chalk line

• Spacing tools

• Fastener-speciﬁc tools

recommended by

manufacturer

Joist spacing requirements

Gapping requirements

5 Meadowcraft Parkway, Selma, AL 36701 800.332.5724 8529_8/18

Deckorators.com

Each Deckorators

Vault board has a unique appearance and should

be arranged according to the end user’s preference. Prior to construction,

check with your local regulatory agency's code requirements. For best

results, follow all installation instructions, paying close attention to

gapping, spacing and fastener requirements.

•

16"

•

16"

•

12"

Eotek4.pdf

Standard Picture frame Diagonal (45°)

Residential 16" 16" 12"

Commercial 12" 12" 12"

Note: All dimensions are on-center.

Installation style

Above 32º F

(0º C)

Below 32º F

(0º C)

Side-to-Side 1/8" 3/16"

End-to-End 1/16" 1/8"

End-to-Side 1/16" 1/8"

Abutting Solid

Objects

1/8" 1/4"

Installation temperature

Each variegated

Deckorators board

has a unique

appearance and

should be arranged

according to the

end user's

preference.

Almacenamiento

Mantenga cubierto antes de ser instalado.

Instalación

• Todas las tablas deben distribuirse de forma adecuada

para permitir la expansión y contracción. Refiérase a las

instrucciones para la instalación completa para detalles.

• Distribuya todo el material para terrazas a 1/4

(6.4 mm) de distancia de cualquier estructura

permanente o poste.

• Utilice como mínimo sujetadores para piso de terraza

de 2-1/2 pulg., resistentes a la corrosión, con rosca

inversa y con recubrimiento.

Espaciado de las vigas

• Espaciado de la viga 16 in (41 cm) en el centro para la

instalación perpendicular a la viga.

• Espaciado de la viga 12 in (31 cm) en el centro para la

instalación diagonal a la viga.

Visite Deckorators.com para instrucciones completas

de instalación, e información de la garantía y el cuidado

y limpieza.

Deckorators es una marca comercial de Universal Consumer Products, Inc. en

los EE.UU.

La garantía está disponible en www.deckorators.com.

Guarde las etiquetas UPC como comprobante de compra.

Rangement

Gardez couvert avant l'installation.

Installation

• Toutes les planches doivent être espacées

correctement pour permettre la dilatation et le retrait.

Consultez les directives d’installation complètes pour

obtenir les détails.

• Éloignez tout le matériau de terrasse de 6,4 mm (1/4

po) de toute structure permanente ou de tout poteau.

• Utiliser des attaches de terrasse en composite enduit,

à filetage inverse, résistantes à la corrosion de au

moins 2-1/2 po.

Espacement des solives

• Espacement aux solives de 41 cm (16 po) entre axes

pour l’installation perpendiculaire aux solives.

• Espacement des solives de 31 cm (12 po) entre axes

pour l’installation diagonale aux solives.

Visitez Deckorators.com pour les instructions complètes

d’installation, garantie et l’entretien.

Deckorators est une marque de commerce déposée de Universal Consumer

Products, Inc. aux États-Unis.

Le texte de la garantie est disponible à l’adresse www.deckorators.com.

Conservez l’étiquette d’extrémité à code UPC comme preuve d’achat.

Storage

Keep covered prior to installation.

Installation

• All boards must be spaced properly to allow for

expansion and contraction. Refer to complete

installation instructions for details.

• Space all decking material 1/4-in away from any

permanent structure or post.

• Use minimum 2-1/2" corrosion-resistant, reverse-thread,

coated composite decking fasteners.

Joist Spacing

• 16-in on-center for installation perpendicular to the joist.

• 12-in on-center for installation diagonal to the joist.

Visit Deckorators.com for complete installation

instructions, warranty and care and cleaning information.

Deckorators is a trademark of Universal Consumer Products, Inc., in the U.S.

Warranty available at www.deckorators.com.

Save UPC end tags for proof of purchase.

8560 10/15

5 Meadowcraft Parkway, Selma, AL 36701 (800) 332-5724

Chaque planche de

platelage possède

une apparence

unique et devrait

donc être

disposée au goût

de l'utilisateur.

Cada tablón tiene

una apariencia

únicay debe ser

colocado de

acuerdo a la

preferencia

del usuario final.

VAULT DECKING

•

16"

•

16"

•

12"

Eotek4.pdf

End Tag

Product Sticker

1X6-16' GR. DKR.

• •

12"

DeckConstr.ai

• •

16"

• •

16"

• •

12"

DeckConstr.ai

• •

16"

• •

16"

• •

12"

DeckConstr.ai

• •

16"

• •

16"

SIDE

VIEW

Standard Picture frame Diagonal

TOP

VIEW

•

16"

•

16"

•

12"

Eotek4.pdf

Note: Always follow best workmanship practices. Including, and

not limited to, square cutting both board ends prior to installation.

EOVATIONS INSTALLATION INSTRUCTIONS, CONTINUED

Cutting

Installation

5 Meadowcraft Parkway, Selma, AL 36701 800.332.5724 8529_8/18

Deckorators.com

• Upcut with a clean/smooth jigsaw blade.

• Cut deck boards with the leading edge of the saw blade,

cutting into the exposed face. Use a sharp utility knife or jigsaw

to ﬁnish cuts where a circular saw cannot fully complete cut.

• Use a jigsaw to cut openings for protrusions.

• If necessary, use a large ﬁle or medium-grit sandpaper

to clean cut edges.

• Use utility knife to cut any ﬁbers or strands.

(In the rare event that a strand or ﬁber protrudes from

the board, do not pull it.)

• Set power driver such that screws are slightly counter sunk.

Do not overdrive.

• If using a hidden fastener system, use the manufacturer’s

recommended fastener and follow the manufacturer’s instructions.

• Two fasteners per joist minimum.

• Ends of each board must fall on a joist.

• Double joist or use blocking where two board ends meet.

• 1" maximum cantilever.

• Install entire deck at same temperature.

• Install the deck boards starting from the outside edge of the platform

and work toward anchor wall so that ripped pieces abut the wall. Start

installing from one end of the board and work toward the other end

of the board.

OR: Start installing from the center of the board and work out toward

the ends of the board. Do not install by fastening each end ﬁrst and

working toward the middle.

• Continue installing deck boards, adhering to the gapping

requirements. Ensure consistent appearance by aligning each

plank so that the cathedrals of the emboss pattern point in the

same direction.

NOTE: Cutting all ends of boards prior to installation recommended.

Fastener requirements

• 10" 40T, 80T circular blade

• 12" 40T, 72T, 80T circular blade

• Corrosion-resistant, galvanized or

stainless steel fasteners

• Reverse-thread composite screw

• Minimum of 2-1/2" long screws

• 1-1/4" minimum penetration into joist

Face screw installation

Hidden fastener installation

3/8"-1"

•

Eotek 6.pdf

16" max.

•

Eotek 7.pdf

Hidden

fastener

Joist

Slot

•

Deck board

• Use reverse-threaded composite deck screws.

• Screws should be 3/8" to 1" from side of board,

3/8" to 1" from end of board.

• Use color-matched screws for best results.

• Use caution not to overdrive screw.

• Please refer to the compatible fastener information

on Deckorators.com/FastenerInfo.

• Fastener slots may be routed into the side of the

deck boards, as needed.

• Follow hidden fastener manufacturer’s instructions.

EOVATIONS INSTALLATION INSTRUCTIONS, CONTINUED

Stair installation

5 Meadowcraft Parkway, Selma, AL 36701 800.332.5724 8529_8/18

Deckorators.com

• Stairs must be constructed according to national and local building

codes. Generally, building codes require 3' minimum wide treads and

11" minimum tread depth.

• 9" maximum center-to-center spacing of stringers is required.

• Stair treads should be fastened over a minimum of 5 stringers to

meet code requirements.

• 1/2" maximum tread overhang over stringers.

• 1/8" minimum gap between stair-tread boards. Local building codes

may require the gap to be increased to 1/4" - 3/8" in order to maintain

the minimum tread depth.

Like most composites, Deckorators Decking will have color variations

from piece to piece. This is due to naturally occurring variations in

polymers. Purchasing all required decking material at one time is

recommended, as manufacturing runs can produce slightly different

colors. Do not install if color variation is not acceptable.

Mold and mildew can be a nuisance on any exterior building surface,

regardless of the material. If the conditions are right, they will grow on

wood, plastic, concrete, metal and other surfaces. Mold formation is

most prevalent in consistently wet, shaded areas. Spores from the nat-

ural environment are carried by the wind and commonly land on decks

surfaces. It is important to note that the appearance of mold/

mildew is a function of nature, not necessarily a deﬁciency with any

of the material on which it grows.

Periodic washing with soap/mild detergent and water will help remove

surface dirt. This will also help prevent the buildup of pollen, debris and

spores that can cause and accelerate mold/mildew growth.

Caution: A pressure washer should not be used to “blast” mold/mildew

or soils from a deck surface. The abrasive nature of the water stream can

potentially cause damage by driving the spores deeper into the material,

which may create a more challenging problem to remedy. A pressure

washer with a fan-tipped nozzle should be used only to lightly wet or

rinse wood or composite deck surfaces.

There are many deck wash and exterior cleaning products available at

retail. It is important to make sure you use a cleaner speciﬁcally intended

for your application. After selecting a product, be certain to read,

Stringer

Stair tread

Eotek2.pdf

9" max.

36" min.

5 stringers

required

11" min.

depth

1/8" min.

gap

•

THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR

USE OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE

CONSTRUCTION OR USE OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED IN THE PROJECT,

INCLUDING, BUT NOT LIMITED TO, WEARING THE APPROPRIATE SAFETY EQUIPMENT. UNIVERSAL FOREST PRODUCTS, INC., MAKES NO WARRANTY, EITHER EXPRESS OR IMPLIED,