COUNTIS E40/E41
E
C
B
A
D
U1
U2
U3
T1/T2 *
*
COUNTIS E41
+
-
N
L2
L1
L3
N
L2
L1
L3
N
11
1 3 5 7 9
4 6 8 10 12 14 16 2
S1 S2 S1 S2 S1 S2
Product presentation
A LCD display.
B Key to scroll readings.
C «Prog» key to set up the CT ratio and the type
of network.
D Reset to reset the partial counter.
E Metrological LED (1 Wh = 10 impulses).
Meter setup
The following settings have to be made before the
meter can be put to use :
- CT ratio.
- Type of network (single or three-phase).
- Type of three-phase installation (balanced or
unbalanced
1. Press the Prog key during 3 sec. to enter the
setup mode.
2. The CT ratio setting is displayed (100A). Press
the key «Read» repeatedly to scroll the possible
CT values (50,60,75,100,125,150,160,200,250,3
00,400,500,600,700,750,800,1000,1200,1250,1
500,1600,2000,2500,3000,4000,5000,6000A).
3. Press «Prog» to conrm and switch to the next
setting.
4. The type of network (1L+N, 2L, 3L, 3L+N) is
displayed. Press the key «Read» repeatedly to
scroll the possible values and select the type of
network.
5. Press «Prog» to conrm and switch to the next
setting.
6. On three-phase installations, the type of
installation is displayed as «Balanced/
Unbalanced» (Bl, Unbl). Press the key «Read»
to scroll the values and select the type of
installation.
7. Press «Prog» to conrm.
8. Press the Prog key during 3 sec. to exit the
programming mode.
Metrological characteristics
- Accuracy class B (1%) according to EN50470-3
- Metrological LED:
1 pulse = 0.1Wh current transformer ratio
e.g. in a installation with a 100/5A C.T.,
1 pulse = 0.1Wh /20 pulses = 2Wh
- Starting current: 10 mA
- Basic current: 5 A
- Max current: 6 A
Technical characteristics
- Consumption: < 0,6 W et 2,8 VA max per phase
- Supply: 230/400 VAC +/- 15%
- Frequency: 50/60 Hz +/- 2 Hz
- Savings of measures are made regularly and in
case of power failure in EEPROM
Display of readings
The various datas can be scrolled by pressing
the Key «Read».
The Default display will indicate power
consumption according to the current tari.
COUNTIS E40:
1 1st pressure : backlight switches ON.
Total active energy consumption (kWh).
2 2nd pressure: partial active energy
consumption (kWh).
3 3rd pressure: total reactive energy
consumption (kVAR).
4 4th pressure: partial reactive energy
consumption (kVAR).
5 5th pressure: instant power consumption (kW).
COUNTIS E41:
The COUNTIS E41 provides detailed display
of the total/partial active energy consumptions
according to tari (T1 or T2) and in total (T).
To reset the partial meter
- Press the scrolling key several times in order
to display partial energy.
- Press the reset button during 3 sec.
The partial meters (active and reactive energy)
will be set to zero.
ERROR message:
In case of bad wiring, an «ERROR» message
will be displayed.
- Check for each phase that current (I1, I2, I3)
and voltage (L1, L2, L3) are measured on the
right phase.
- Check the correct wiring of the product (L/N).
Note :
The information
on the display indicates
that the corresponding phase (1, 2,3) is under
voltage. The information is available only when
the neutral is connected.
- Characteristic of tari input COUNTIS E41:
tari 1 = 0 V, tari 2 = 230 VAC +/- 15%
- Impulse output characteristics:
• 1 pulse: 100 Wh
• Pulse duration: 100 ms
• External supply: 20 ... 30 VDC
Mechanical characteristics
- Modular casing 4 M (72 mm)
- Protection degree (casing) : IP20
- Protection degree noze: IP50/IK03
- Insulation class: II
Environment
- Storage temperature: -25 °C to +70 °C
- Working temperature: -10 °C to +55 °C
- Connection capacity:
• exible: 1 à 6 mm
2
• rigid: 1,5 à 10 mm
2
Operating principle
This kilowatt hour meter measures the active and reactive electrical energy used in an electrical
installation.
This device has a digital LCD to display energy used and power.
This device has a total counter and a partial resettable counter.
In case of two tari levels, the COUNTIS E41 will count separetely the energy used in tari 1 and in tari 2.
Technical specications
Note:
in a unbalanced network, please connect 1 C.T.
for each phase. If the installation settings is
related to a "balanced network", 1 C.T. on the
phase 1 has to be connected.
COUNTIS E40 / E41
Three phase kWh meter,
measure via CT 50 to 6000 A
USER
MANUAL
CORPORATE HQ CONTACT: SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE
Recto / papier blanc offset 70g/m
2
/ noir et blanc / format ouvert : 210x297 mm / format plié 70x75 mm. Subject to change without notice.
EN
www.socomec.com
537204B
-
1
dans d''autres langues
Documents connexes
-
Socomec COUNTIS E4x Mode d'emploi
-
-
-
-
-
-
-
-
-